Hardware List
Part List
Home Styles Customer Service: www.homestyles-furniture.com,
888-680-7460, 877-831-0319
Hex Wrench
1 pc.
Adjustable Pin
12 pcs. (+1 extra)
Magnet
1 pc.
Knob
1 pc.
Handle
1 pc.
Wood Screw (long)
M3.5x25
8 pcs. (+1 extra)
20 05525 0992
Bar
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Tool(s) required for assembly: LevelPhillips screwdriver,
Refer to later page(s) of these
instructions for drawer assembly.
M3.5x16
Wood Screw
4 pcs. (+1 extra)
B.
Side Panel
1 pc.
C.
Side Panel
1 pc.
D.
Middle Panel
1 pc.
G.
Shelf
1 pc.
J.
Shelf
1 pc.
K.
Shelf
2 pcs.
M.
Drawer
1 pc.
N.
Foot Rest
1 pc.
O.
Foot Rest Support
3 pcs.
H.
Rail
1 pc.
Carton 20 05525 0991 is also needed for assembly.
Cam Lock Screw
35 pcs. (+1 extra)
Cam Lock
35 pcs. (+4 extra)
M3.5x16
Tapered Wood Screw
12 pcs. (+1 extra)
Machine Screw
3 pcs.
M4x25
M3x13
Wood Screw
for Magnet
2 pcs. (+1 extra)
I.
Base
1 pc.
Assembly Instructions 2/6
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
STEP 1
Insert Cam Lock Screws into pre-drilled holes in Top (A), Side Panels (B), (C),
Middle Panel (D), Front Panels (E), (F), Shelf (G) and Base (I), then tighten.
(See Figure 1)
Figure 1
Cam Lock Screw
A
B
C
D
E
F
I
G
E
Cam Lock
Assembly Instructions 3/6
STEP 3
Attach Side Panels (B) and (C)
to unit with Cam Locks.
B
C
Cam Lock
Figure 2
Cam Lock
Wood Screw for Magnet
Magnet
H
G
D
STEP 2
Attach Magnet to Rail (H)
with Wood Screws for Magnet into
pre-drilled holes. (See Figure 2)
Attach Shelf (G) and Rail (H) to Middle Panel (D)
with Cam Locks. (See Figure 3)
STEP 4
Place Front Panels (E) and (F)
face down on a soft cloth.
Attach Front Panel (E) to
Front Panel (F) to with Cam Locks.
Attach unit to front panel unit
with Cam Locks.
F
Figure 3
Assembly Instructions 4/6
STEP 6
Turn unit from Step 4 upside down
and place on a soft cloth.
Attach Base (I) to unit from Step 4
with Cam Locks.
I
Cam Lock
STEP 5
Slide Foot Rest (N) into
Foot Rest Supports (O).
Attach Foot Rest Supports (O) to Base (I) with
Tapered Wood Screws into pre-drilled holes.
Attach Foot Rest (N) to Foot Rest Supports (O), leaving same amount of Foot Rest (N)
protruding on outside of outer Foot Rest Supports (O). (See Figure 4)
O
N
Same amount of Foot Rest (N)
on each side
Tapered
Wood Screw
I
O
O
Figure 4
Assembly Instructions 5/6
Part ListPart List
Drawer (M)
M2.
Drawer Back
1 pc.
M5.
Drawer Bottom
1 pc.
M3.
Drawer Side
1 pc.
M4.
Drawer Side
1 pc.
M1.
Drawer Front
1 pc.
STEP 7
Attach Drawer Front (M1) and Drawer
Back (M2) to Drawer Side (M3)
with Wood Screws (long).
Attach Drawer Side (M4) to unit
with Wood Screws (long).
Bottom
M1
M3
M4M2
Wood Screw (long)
Roller at back
M5
STEP 8
Slide Drawer Bottom (M5) into groove.
Attach Drawer Bottom (M5)
to unit with Wood Screws.
Wood Screw
STEP 9
Attach Handle with Machine Screws.
Machine Screw
Handle
STEP 10
Turn unit over to its upright position.
Insert Adjustable Pins into middle panel and
side panels at desired level. (See Figure 5)
Place Shelves (J) and (K) into position.
Attach Door (L) to unit by sliding door hinges
into side panel hinges. (See Figure 6)
Attach Knob to Door (L) with Machine Screw.
(See Figure 7)
Attach Top (A) to unit with Cam Locks.
Slide Drawer (M) into position.
Level unit by adjusting the adjustable
levelers on bottom of unit. (See Figure 8)
Note: Unit must be level to work properly.
Figure 7
Figure 6
Figure 8
Figure 5
Assembly Instructions 6/6
Cam Lock
Machine Screw
Knob
Adjustable Pin
A
M
L
J
K
K
NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
888-680-7460, 877-831-0319
/
