jWIN JD-VD745 Operating instructions
- Category
- DVD players
- Type
- Operating instructions
DVD / CD PLAYER
JD-VD745 V1.1
OPERATION MANUAL
2
INVISIBLE LASER
OPEN AND INTERLOCK
FAILS OR IS DEFEATED.
AVOID DIRECT EXPOSURE
TO THE LASER BEAM.
DANGER
LASER SAFETY
This unit employs an optical laser beam system in the CD mechanism, designed
with built-in safeguards. Do not attempt to disassemble; refer to qualified service
personnel. Exposure to this invisible laser light beam may be harmful to the human eye.
THIS IS A CLASS-1 LASER PRODUCT. USE OF CONTROLS, OR
ADJUSTMENTS OR PROCEDURES OTHER THAN THOSE SPECIFIED
HEREIN, MAY RESULT IN HAZARDOUS LASER LIGHT BEAM EXPOSURE.
PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE OPERATING THIS UNIT.
THIS PRODUCT MAY BE IS SOLD WITH AN AC ADAPTER AND A CAR ADAPTER
AC Adapter Car Adapter
1. Input : AC100-240V~ 0.5A 50-60Hz 1. Input : DC . . . 12V
2. Output: DC 9V / 2000mA 2. Output : DC . . . 12V 2A
WARNING
To prevent fire or shock hazard, do not expose this appliance to rain or moisture. The apparatus
should not be exposed to dripping or slashing and no objects filled with liquids, such as vases,
shall be placed on the apparatus. Ventilation should not be impeded by covering the ventilation
openings with items, such as newspapaers, tablecloths, curtains, etc.
No nakedflame sources, such as lighted candles, should be placed on the apparatus.
Car Adapter Fuse Replacement
Should the player fail to operate with the DC car adapter/cord, check the fuse (UL 2A 250V, CUL
T2AL 250V). If blown, check all connections and inspect the adapter cord for any damage. Always
replace the fuse with the same type and rating. If the fuse blows again after replacement, a
potential problem is indicated. DO NOT replace fuse with a higher rating, as doing so may cause
damage to the player.
CAUTION
Since the CD circuitry may cause interference to other radio tuners nearby, switch this unit off when
not in use or move it away from the affected radio tuner.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE
RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER
(OR BACK). NO USER-
S E R V I C E A B L E PA R T S
INSIDE, REFER SERVICING
TO QUALIFIED SERVICE
PERSONNEL.
The exclamation point within an
equilateral triangle is intended
to alert the user to presence of
important operating and main-
tenance (servicing) instructions
in the literature accompanying
the appliance.
The lightning flash with an arrowhead
triangle, is intended to alert the user
to the presence of an uninsulated "dan-
gerous voltage" within the product's
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesirable operation.
This Class B digital apparatus complies with Canadian ICES-003.
RADIATION WHEN
symbol, within an equilateral
3
Getting Started
Before attempting to connect, operate or adjust this product, please read these
instruction completely and keep this manual for future reference.
Dear Customers :
May we take this opportunity to thank you for purchasing this DVD Player.
We strongly recommend that you carefully study the operating instructions before
operating the unit.
Main Features
• Front loading DVD / MP3 / CD player.
Standards
Video : NTSC or PAL
Audio : LT/RT stereo
Power sources
Battery Installation
Follow the step to install and release the battery pack.
Battery Operation
1. Fully charge the battery before use.
2. Do not short circuit the battery and unintentionally reverse charge it.
3. Do not dispose of the battery in a fire and keep away from damage.
4. Store the battery, uncharged, in a cool and dry place.
5. Dispose of properly in accordance with local law.
Battery Specifications
Charging Voltage : DC 9V / 2000mA
DC Output : DC 7.2V / 4000mA/H
Charged Condition : Red LED light indicates that the battery is being charged.
Green LED light indicates that the battery is fully charged.
Note : Charge within the surrounding temperature range of 10°C ~ 30°C condition.
(See page 17 : Caution on Charging Battery pack)
• Install the battery pack
Put the battery pack on the bottom of the
DVD main unit. Refer to the arrow direction
of following diagram to lock the battery
pack.
• Release the batterye pack
Slide OPEN knob on the side of the battery
pack to release it from the DVD main unit.
4
* Player is CD-R, CD-RW compatible.
Note: CD-R, CD-RW discs recorded with writing device can only be used when they are
correctly treated.
Region Management Information
This DVD Player is designed and manufactured to respond to the Region Management
Information that is recorded on a DVD disc. If the Region number described on the DVD
disc does not correspond to the Region number of this DVD Player, this DVD player can-
not play that disc.
This Region number of this DVD player is
.
Disc maintenance
– Before playback, wipe the disc from the center hole toward the outer edge with a clean
cloth.
– Never use bezine, thinner, cleaning fluid, static electricity prevention liquids or any
other solvent.
Note : Dirty disc may cause bad picture.
Audio & Video
Audio
Audio & Video
Disc size 12cm
single side, single layer / single side, double layer
PAL and NTSC DVD disc
Playback time 135min / 240min max.
Disc size 12cm / 8cm
CD disc
Playback time 74min/20min max.
CD-G format disc
Disc types
Correct
From the center to the edge
Incorrect
CD-G
5
Safety precautions
Warning
To avoid electrical shock, do not open the
cabinet, refer servicing to qualified person-
nel only.
Warning
Keep the unit away from flower vases, tubs,
sinks, etc. If liquids are spilt into the unit,
serious damage could occur.
Warning
Do not expose this equipment to rain or
moisture.
Warning
Do not block ventilation holes of the unit so
that air can circulate freely.
Attention
If smoke, malodor or unrelated noise are
emitted from the unit, turn off the power and
disconnect the AC power cord.
Attention
Touching the unit is dangerous especially if
during thunder.
Attention
When left unused for a long period of time,
the unit should be unplugged from the house-
hold AC outlet.
Attention
Be sure to turn the unit off and disconnect the AC
power cord before cleaning the unit surface. If the
surface is dirty, wipe clean with a cloth which has
been dipped in a weak soap and water solution and
wrung out thoroughly, and then wipe again with a
dry cloth.
Note: This unit is a class 1 laser product and uses a visible laser beam which could
cause hazardous radiation exposure if directed. Be sure to operate it correctly as
instructed.
6
1. Speaker
2. Remote Sensor
3. Power On / Line In Indicator
a. Power On - Green light
b. Line In - Orange light
4. Power On/Off Switch
5. Open Knob
6. LCD On/Off
7. Title Button
8. Menu Button
9. Setup Button
10. Next Button
11. Previous Button
12. Display Button
13. Direction Buttons
(Up / Down / Left / Right )
14. Enter Button
15. Push Knob
16. Pause Button
17. Stop Button
18. Play / Enter Button
19. Volume Control
20. Headphones Output Jack
21. A/V Output Jack
22. A/V Input Jack
23. Line IN/OUT Selector Switch
24.
25. DC IN: 7.2V – 12V
26. Battery
1
2
5
6
18
3 4 19 20
21
22 24
23 25 26
8
11
12
7
9
10
13
14
171615
Location of Controls
Note: When using the LINE IN
setting of the selector switch, the
LCD screen will be blank if there
is no video input present at the
A/V Input Jack (22).
S-Video Output
7
Battery Installation (Remote Control Unit)
1. Remove the battery cover.
2. Insert two batteries (AAA) making sure the polarity (+/-) matches the marks inside the
unit.
3. Replace the cover.
– Do not attempt to recharge, short-circuit, disassemble, heat or throw the batteries into
a fire.
– Do not mix old and new batteries
Note : Weak batteries can leak and severely damage the remote control unit.
Remote Control Unit
1. Zoom Button
2. Standby Button
3. Numeric Buttons
4. Subtitle Button
5. Display Button
6. Audio Button
7. Angle Button
8. Setup Button
9. Play / Enter Button
10. Direction Buttons
( Up / Down/ Left/ Right)
11. PIC Menu Button
12. Picture – Button
13. Picture + Button
14. Title Button
15. Mute Button
16. Slow Button
17. Search Button
18. Program Button
19. Repeat A-B Button
20. Repeat Button
21. DVD Menu Button (VCD PBC On/Off)
22. Stop Button
23. Step/Pause Button
24. Fast Backward Button
25. Fast Forward Button
26. Next Button
27. Previous Button
8
GETTING STARTED
The following steps will help you to get your JD-VD745 ready for use.
CHARGING THE BATTERY
1. Begin by locating the Battery Pack and the Power Supply Switching Adapter.
2. Plug the adapter’s circular connector into the battery’s connector labeled “DCIN 9V”
found on its side. Do NOT attempt to plug the adapter’s connector into the battery’s
“pigtail” lead on the opposite side of the battery.
3. Plug the adapter into a convenient electrical outlet.
4. Confirm that the battery’s CHR (Charging) LED, located adjacent to its “DC IN 9V”
connector) is also lit. If RED, the battery is in need of a charge and is being charged.
If GREEN, the battery is fully charged, and further charging is not necessary,
although no harm will be done to the battery if charging is continued.
5. You cannot overcharge the battery. If you prefer, you may keep the battery charged,
whether separated or attached to the DVD player (see below).
NOTE:For extended periods of non-use, however, store the battery,
disconnected from its charger, in a cool and dry place.
INSTALLING THE BATTERY ON THE DVD PLAYER
1. Be sure the unit is OFF by checking that its POWER ON/OFF switch (item 4 on
page 6) is in the OFF position.
2. With the battery properly charged as described above, disconnect it from the
charger and orient it as shown on page 3.
3. To prevent possible damage to the LCD display, close its lid (if it is open) until it
latches. Refer to the illustration at the upper right of page 6, and place the battery at
the rear of the unit so that the two protrusions on the inner vertical surface of the
battery align with the two slots at the rear of the unit. Once done, slide the battery
away from you, until it “clicks” in place.
4. With the battery attached to the unit as described, plug its “pigtail” lead into the
unit’s DC IN 9V jack, (item 25, shown on page 6). The unit’s Power LED (item 3on
page 6) will turn RED. Operate the unit as described in the following pages.
NOTE:Removing the battery requires that the OPEN switch (on the opposite side of
the battery) be pushed to the rear. Once done, the battery can be removed from
the unit. Don’t forget to unplugthe "pigtail" lead.
USING THE JD-VD745 WITHOUT THE BATTERY
1. The unit can be used without the battery. Turn the unit off and remove the battery
as described above.
2. Plug the AC adapter's circular connector into the unit's DC IN 9V jack (item 25 on
page 6. If necessary, plug the other end of the AC adapter into a working wall outlet.
3. Operate your unit as described in this manual.
9
O P E R A T I O N
PLAYING DISCS
1. If necessary, turn the unit ON with the Power Switch. The unit’s Power LED should be
GREEN, indicating that the battery is not in need of a charge. The unit will attempt to load
a disc if one is present under the disc cover. Press the PUSH TO OPEN button (item 15 on
page 6), on the left side of the front panel to open the DVD door and put a disc on the loader,
with the label side facing up. For double-sided DVD discs, mount the disc with the "A1"
label (the Side 1 equivalent label) facing up.
2. Close the DVD door, and the disc will be loaded automatically. Once loaded,
if it is a DVD disc, it will start playing automatically, typically showing either the
Menu/Title Page on the screen or previews of coming attractions.
if it is a CD, it will play the first track directly.
PRE-STOP []
3. Press the STOP button (item 17 on page 6 / item 22 on page 7) once if you want invoke the
PRE-STOP mode. PRE-STOP stops the playback, displays the manufacturer’s logo, and
allows playback to be resumed from the point at which STOP was pressed--simply by
pressing the PLAY/ENTER button (item 18 on page 6 / item 9 on page 7). PRE-STOP is
very similar to PAUSE, except that PAUSE freezes the existing video on the screen, while
PRE-STOP replaces it with the aforementioned logo.
4. Pressing the STOP button twice completely stops the disc, and causes the unit to enter
the STOP mode, where the disc ceases to spin, and playback can no longer be resumed
from the point at which the STOP button was pressed.
(PAUSE) STEP []
5. The PAUSE function is applicable to both DVDs and CD audio discs:
a. The PAUSE function (II) is initiated by pressing the PAUSE button (item 16 on
page 6 / item 23 on page 7).
b. For DVDs, pressing PAUSE causes the picture to freeze and the sound to
cease.
c. For CD audio discs, pressing PAUSE causes the sound to pause and be muted.
d. Press the PLAY/ENTER button again to resume normal play.
6. The STEP function (available only on the remote control (item 23 on page 7) is
activated only after PAUSE is invoked.
a. Each press of this key advances the video content by a small interval. The audio is
silent.
b. Cancel the PAUSE or STEP function by pressing PLAY.
DVD SETUP MODE
7. Setup Mode provides the menus for the configuration of the SYSTEM SETUP,
LANGUAGE SETUP, VIDEO SETUP, and SPEAKER SETUP categories.
a. Press the SETUP button (item 9 on page 6 / item 8 on page 7) to display the
Setup Menu.
b. Along the top of the initial display are four icons, each representing one of the four
categories listed above. By using the left [] or right [] direction keys (item 13 on
page 6 / item 10 on page 7), it is possible to highlight the desired category, whose
name will also be displayed in yellow type below the icons.
c. The following section will cover all four configuration categories and their
settings
10
8. To exit the Setup Menu, press the SETUP button again or scroll down to EXIT
SETUP (use the down [] direction key to highlight the phrase, and the
PLAY/ENTER key to select EXIT SETUP, after which, the unit was display its logo,
and wait for the next command.
OPERATING EXTERNAL DEVICES THROUGH YOUR JD-VD745
SENDING OUTPUT SIGNALS FROM YOUR JD-VD745 TO AN EXTERNAL DEVICE
Your JD-VD745 can send its video and audio content to an external device (typically a
TV), in order to be viewed on a larger screen, and heard on bigger speakers. There are
two ways that your JD-VD745 supplies these external signals. The first, called
"composite" video, combines video and audio content into a single “composite”cable,
which is supplied with your JD-VD745. On one end of the cable, there is a 1/8”(3.5mm)
miniature phone plug for connection to your JD-VD745’s A/V out jack. On the other end
of this cable, there are three RCA-type connectors, consisting of a YELLOW Video
connector, and two Audio connectors, one being WHITE (to carry left channel audio),
and the other RED (for right channel audio). When used only with an external TV, all
three RCA connectors plug into the TV, but when the TV is used in combination with an
audio system (for better sound), the two Audio connectors must be plugged into the
appropriate sound system inputs.
To achieve the same results, you can connect an S-VIDEO cable (not included) between
your JD-VD745’s S-VIDEO jack, and an external TV equipped with an S-VIDEO input
connector (and, if desired, an external audio system, as well). In either case, in addition
to the S-Video cable you will have to use the supplied Audio cable to provide sound to
the TV, or to the sound system (since the S-Video cable carries only video signals).
In some cases, you may want to your VCR to record DVD images being played on your
JD-VD745. In such cases, your cabling would be the same as shown on the Quick
Guide’s first two examples, but you must be aware that only non copy-protected DVDs
will record properly on your VCR. Attempting to record copy protected DVD video
material is illegal and will likely produce unsatisfactory results.
RECEIVING INPUT SIGNALS FROM EXTERNAL DEVICES AT YOUR JD-VD745
Your JD-VD745 is also capable of receiving and playing content from external devices
like VCRs, game consoles, audio systems, and portable CD players, using the
JD-VD745's LCD screen and speakers as the means for viewing the resulting images
and its audio content.
The Quick Guide contains an illustration of the proper techniques to do this in its third
example.
FINALLY, REMEMBER THE LINE SELECT SWITCH
Be sure that the JD-VD745’s LINE SELECT switch (item 23 on page 6) is placed in the
OUT position when you want the unit’s A/V output signals to be sent to the external
device(s). Similarly, the switch must be placed in the IN position to properly receive all
A/V input signals sent by the external device(s). Refer to the Quick Guide for
clarification and examples.
Your JD
-
VD745 comes with a
one page
Quick
Connection
Guide
to
which you may want to refer when reading the following material.
11
SYSTEM SETUP
In STOP mode, press the SETUP button and highlight SYSTEM setup with remote control.
Once done, press the ENTER button to confirm.
To select the desired item, use the direction buttons ( ,,,), then press the ENTER
button to confirm the selection.
TV SYSTEM
- NTSC (default)
-PAL
SCREEN SAVER
- ON (default)
- OFF
TV TYPE
- 4:3 PS (Pan Scan)
- 4:3 LB (Letter Box)
- 16:9 (wide screen) (default)
DEFAULT: RESTORE
Choose this option to restore all
the choosen setup options to
their default (factory) settings.
SYSTEM SETUP
TV SYSTEM
NTSC
SCREEN SAVER PAL
TV TYPE
DEFAULT
EXIT SETUP
SYSTEM SETUP
TV SYSTEM
SCREEN SAVER
TV TYPE
4:3 PS
DEFAULT 4:3 LB
16:9
EXIT SETUP
SYSTEM SETUP
TV SYSTEM
SCREEN SAVER
TV TYPE
DEFAULT
RESTORE
EXIT SETUP
SYSTEM SETUP
TV SYSTEM
SCREEN SAVER
ON
TV TYPE OFF
DEFAULT
EXIT SETUP
12
LANGUAGE SETUP
In the STOP mode, press the SETUP button and then the direction (and) to highlight
LANGUAGE SETUP. Once done, press ENTER.
OSD LANGUAGE
(ON SCREEN DISPLAY) LANGUAGE
Press the UP/DOWN direction buttons (/) to
highlight the OSD LANGUAGE. Press ENTER to
move the cursor to the column of choices. Use
the (/) buttons to select the desired OSD
Language, and press ENTER:
- ENGLISH (default)
- GERMAN - FRENCH
- SPANISH - ITALIAN
AUDIO LANGUAGE
Press the direction (/) buttons to highlight
the AUDIO LANG and press ENTER.
Use the (/) button to select the desired
AUDIO Language, and press ENTER:
- ENGLISH (default)
- GERMAN - FRENCH
- SPANISH - ITALIAN
SUBTITLE LANGUAGE
Press the direction (/) buttons to highlight
the SUBTITLE LANG and press ENTER.
Use the (/) buttons to select the desired
SUBTITLE Language, (or OFF to select none)
and press ENTER:
- ENGLISH (default) - FRENCH
- GERMAN - ITALIAN
- SPANISH - OFF
MENU LANGUAGE
Press the direction (/) button to highlight the
MENU LANG and press ENTER.
Use the (/) buttons to select the desired
MENU Language, and press ENTER:
- ENGLISH (default)
- GERMAN - FRENCH
- SPANISH - ITALIAN
LANGUAGE SETUP
OSD LANGUAGE
ENGLISH
AUDIO LANG GERMAN
SUBTITLE LANG SPANISH
MENU LANG FRENCH
ITALIAN
EXIT SETUP
LANGUAGE SETUP
OSD LANGUAGE
ENGLISH
AUDIO LANG GERMAN
SUBTITLE LANG
SPANISH
MENU LANG FRENCH
ITALIAN
EXIT SETUP OFF
LANGUAGE SETUP
OSD LANGUAGE
ENGLISH
AUDIO LANG
GERMAN
SUBTITLE LANG SPANISH
MENU LANG FRENCH
ITALIAN
EXIT SETUP
LANGUAGE SETUP
OSD LANGUAGE
ENGLISH
AUDIO LANG GERMAN
SUBTITLE LANG SPANISH
MENU LANG
FRENCH
ITALIAN
EXIT SETUP
13
VIDEO SETUP
In the STOP mode, press SETUP button and press direction / buttons to highlight
VIDEO setup. Then press ENTER button to confirm.
• BRIGHTNESS
Using direction / button to move the scroll bar and
adjust the brightness.
• CONTRAST
Using direction / button to move the scroll bar and
adjust the contrast.
• HUE
Using direction / button to move the scroll bar and
adjust the hue.
• SATURATION
Using direction / button to move the scroll bar and
adjust the sauration.
SPEAKER SETUP
In the STOP mode, press SETUP button and highlight SPEAKER setup. Then press
ENTER button to confirm.
• DUAL MONO
- LT/RT
- STEREO (default)
VIDEO SETUP
BRIGHTNESS – – 12
CONTRAST – – 10
HUE – – 8
SATURATION
– – 6
– – 4
EXIT SETUP – – 2
– – 0
VIDEO SETUP
BRIGHTNESS – – + 6
CONTRAST – – + 4
HUE
––+ 2
SATURATION – – 0
–– - 2
EXIT SETUP – – - 4
–– - 6
VIDEO SETUP
BRIGHTNESS
––12
CONTRAST – – 10
HUE – – 8
SATURATION – – 6
– – 4
EXIT SETUP – – 2
– – 0
VIDEO SETUP
BRIGHTNESS – – 12
CONTRAST
––10
HUE – – 8
SATURATION – – 6
– – 4
EXIT SETUP – – 2
– – 0
SPEAKER SETUP
DOWNMIX
LT/RT
STEREO
EXIT SETUP
14
DVD
OPERATION
DVD Menu Play
The DVD Menu Play function is only applicable for DVD movie. User can access the Casting
information, Production History, Movie Introduction etc. directly through this function.
1. Press the DVD MENU key on the remote control to enter the Root Menu.
2. Use the direction button ( / / / ) or input the item index through the Number keys
(0-9) to do the selection.
3. Press ENTER to confirm the selection.
Audio
This function is applicable for DVD and CD audio but with different effects.
- Pressing the AUDIO key will change the Audio channel.
Note :
• When AV is ON, this key has no function.
Scan
This function is applicable for DVD and CD audio but with different effects. The FAST
FORWARD and FAST BACKWARD keys are used to achieve fast play function.
• For DVD, there are 4 different levels of speed (x2, x4, x8, x20) available. Press the
FAST button to cycle speed.
• For CD audio, the FORWARD / BACKWARD keys will play at high speed.
Note :
• Press PLAY key at any stage will resume to normal speed.
• This function is not available when playing CD-G discs.
PREV. / Next
During playback, press PREV or NEXT key :
• When the PREV. key is pressed once, playback returns to the beginning of the
PREVIOUS playing chapter or track.
• When the NEXT key is pressed once, playback starts at the beginning of next chapter
or track.
Slow Play
The Slow Forward is only available for DVD. There are 6 steps of slow motion speed:
1/2, 1/3, 1/4, 1/5, 1/6, 1/7. Press SLOW key to cycle playback speeds.
Note :
• Press PLAY key to resume normal playback speed.
• This function is not available for CD-G.
Repeat Mode
This function is applicable for DVD and CD audio but with different effects.
• For DVD disc playback, user can choose to repeat the current chapter, current title and
disc. Subsequent button press of the REPEAT button can change between these three
options.
• For CD, user can choose to repeat the current track or the whole disc (Repeat All).
Subsequent button press of the REPEAT button can change between these two
options.
15
Repeat AB
User can specify the repeating interval by marking the starting point and the end point.
1. Press the REPEAT AB button to mark the starting point (Playback will continue).
2. Press the REPEAT AB button to mark the end point (The marked part will be repeated
automatically.)
Note :
• Press the REPEAT AB button during repetition will disable the Repeat mode.
• This function is not available for CD-G.
Subtitle
This function is only applicable for DVD disc. It can change the subtitle language shown on
the screen.
Note :
• Number of subtitle available depends on the DVD disc.
• This function is not available for CD-G.
Angle
Some discs may have multiple viewing angles during production. The ANGLE button is to
select the viewing angle shown on the screen.
Note : The number of Angle of View depends on the disc.
Search
The user can access a specific location or a specific track by keying in the targent time or the
track number.
1. Press the SEARCH button to enter to search mode.
2. Input the target time to the number button (0-9) and press the ENTER button. The player
will jump to the target location immediately.
Display
This funciton is to show the time and status information on the screen.
Resume Play
This function is in playback mode. When the STOP button is pressed once, the player will
enter the Resume Play mode. At this time, if the PLAY button is pressed, the player will
resume playback at the location when the STOP button is pressed. If the STOP button is
pressed a second time, resume mode cancels.
Zoom
This function will enlarge or reduce a still picture or a moving picture by pressing the ZOOM
button to select the levels of zooming (2, 3, 4, 1/2, 1/3, 1/4)
Note :
• Use the direction buttons (///) to navigate within the image.
• This function is not available for CD-G.
PIC. MENU
Press PIC. MENU button to select the PICTURE, BRIGHTNESS, CONTRAST, 4:3/16:9,
HUE functions and press the +/- button to adjust the desired level.
16
PROGRAM MODE
This function is applicable for DVD and CD audio. User can assign the playback
sequence according to his/her preference. For CD audio, user can assign the track
sequence. For DVD disc, user can assign both the Title and Chapter sequence.
• CD/CDG
1. Press the PROGRAM button. The Program
Sequence table will be shown on the screen.
2. Enter the track number according to the user
preference through the Number keys (0-9) on
the remote control.
3. After assigning the playback sequence, move
the highlight cursor to the PLAY option by using
the navigation arrows. Press ENTER on the
remote control to confirm.
• DVD
1. Press the PROGRAM button. The Program
Sequence table will be shown on the screen.
2. Enter the Title number with the number keys
(0-9) on the remote control.
PROG
1 - - - - 5 - - - - 9 - - - - 13 - - - -
2 - - - - 6 - - - - 10 - - - - 14 - - - -
3 - - - - 7 - - - - 11 - - - - 15 - - - -
4 - - - - 8 - - - - 12 - - - - 16 - - - -
PLAY CLEAR
PROG
1 0001 5 - - - - 9 - - - - 13 - - - -
2 0003 6 - - - - 10 - - - - 14 - - - -
3 0005 7 - - - - 11 - - - - 15 - - - -
4 - - - - 8 - - - - 12 - - - - 16 - - - -
PLAY CLEAR
PROG
1 0001 5 - - - - 9 - - - - 13 - - - -
2 0003 6 - - - - 10 - - - - 14 - - - -
3 0005 7 - - - - 11 - - - - 15 - - - -
4 - - - - 8 - - - - 12 - - - - 16 - - - -
PLAY CLEAR
PROG
T C T C T C T C
1 - -:- - 5 - -:- - 9 - -:- - 13 - -:- -
2 - -:- - 6 - -:- - 10 - -:- - 14 - -:- -
3 - -:- - 7 - -:- - 11 - -:- - 15 - -:- -
4 -- :- - 8 - -:- - 12 - -:- - 16 - -:- -
PLAY CLEAR
PROG
T C T C T C T C
1
02
:- - 5 - -:- - 9 - -:- - 13 - -:- -
2 - -:- - 6 - -:- - 10 - -:- - 14 - -:- -
3 - -:- - 7 - -:- - 11 - -:- - 15 - -:- -
4 -- :- - 8 - -:- - 12 - -:- - 16 - -:- -
PLAY CLEAR
17
3. Enter the Chapter number of the Title selected in
the last step.
4. Repeat steps 2 - 3 to input the sequence.
5. After assigning the playback sequence, move the
highlight cursor to the START option by using
the Navigation Arrows. Press ENTER on the
remote control to confirm.
To cancel the program:
Move the highlight cursor to the desired program by
using the navigation arrows, and then press the CLEAR
button to delete the selected program.
Picture CD
Load a picture CD into the tray, so the disc can be identified. The player will start showing
each picture (JPG) in sequence (in a slide show format).
Operation
During Slide Show Mode:
• Press the STOP button. It will shift to the Digest Mode in which 6 pictures will be shown
on the screen at a time.
• Press the PAUSE button. It will freeze the screen so that the current picture can be held
for a long time. To resume the slide show mode, press the PLAY button.
• Press the NEXT button on the remote control to skip to the next picture.
• Press the PREVIOUS button on the remote control to repeat the current picture.
• Pressing the PROGRAM button will change the picture effect as indicated below:
1) EXTEND FROM CENTER H
2) EXTEND FROM CENTER V
3) NONE
PROG
T C T C T C T C
1
02
:
03
5 - -:- - 9 - -:- - 13 - -:- -
2 - -:- - 6 - -:- - 10 - -:- - 14 - -:- -
3 - -:- - 7 - -:- - 11 - -:- - 15 - -:- -
4 -- :- - 8 - -:- - 12 - -:- - 16 - -:- -
PLAY CLEAR
PROG
T C T C T C T C
1
02
:
03
5 - -:- - 9 - -:- - 13 - -:- -
2
01
:
01
6 - -:- - 10 - -:- - 14 - -:- -
3
03
:
04
7 - -:- - 11 - -:- - 15 - -:- -
4 -- :- - 8 - -:- - 12 - -:- - 16 - -:- -
PLAY CLEAR
PROG
T C T C T C T C
1
02
:
03
5 - -:- - 9 - -:- - 13 - -:- -
2
01
:
01
6 - -:- - 10 - -:- - 14 - -:- -
3
03
:
04
7 - -:- - 11 - -:- - 15 - -:- -
4 -- :- - 8 - -:- - 12 - -:- - 16 - -:- -
PLAY CLEAR
18
TROUBLESHOOTING
Check the following guide for the possible cause of a problem before contacting service.
Symptom
The unit is NOT
receiving power
The power is ON,
but the unit does
not operate
There is no picture
(and/or sound), and
the Power LED is lit
in AMBER, rather
than GREEN
Poor picture and/or
audio quality.
The DVD player
does not start
playback
The remote control
does not work
properly
Cause
• The AC adapter is disconnected
from the wall outlet or is not
connected to the unit.
• The battery is depleted.
• No disc is inserted.
• The “Line Select” switch is set to
IN, but there is no external video
input available (see page 6).
• The external video/audio cable(s)
are not connected securely.
• The external video/audio
equipment is powered off.
• A dirty or scratched disc is being
played.
• No disc is inserted.
• An unplayable disc is inserted.
• The disc is placed in the unit
upside down or misaligned with
the guides.
• The disc is dirty.
• A menu is still on the screen
• Not pointed at the unit.
• Operated too far away.
• Obstacle in remote’s path.
• Batteries in remote are low.
Correction
• Plug the AC adapter securely into the
wall outlet and securely into the unit,
as well.
• Be sure the battery is fully charged.
If unable to be charged, the battery
will have to be replaced.
• Insert a disc.
• Set the “Line Select” switch
appropriately, for either an external
video source (IN) or for internal disc
usage (OUT). Refer to page 6 for
additional information on this switch.
• Check the unit for the proper
external connections.
• Turn on the externally connected
equipment.
• Clean the disc by following the
procedure on page 4.
• Insert a disc
• Insert a playable disc. (Check the
disc type, the TV System menu, and
the Regional Code).
• Place the disc on the disc tray with
the proper orientation.
• Clean the disc.
• Press the SETUP button on the unit
or remote control to close the menu
screen.
• Point remote at unit’s sensor.
• Operate with 23 feet (7m).
• Remove the obstacle.
• Replace the batteries.
19
Cleaning and Maintenance
Many plastic parts are used in this DVD player casing. Do not use volatile chemicals
such as benzene or thinner. This might damage the finish.
Wipe the casing with a soft, dry cloth. For excessive dirt, use a cloth dampened in a
diluted neutral detergent and wipe again with soft, dry cloth.
Wipe off fingerprints or dirt on the LCD screen using a soft, dry cloth.
SPECIFICATIONS
GENERAL
Power source
Power consumption
External dimensions (WxHxD)
Operating conditions
Operation status
Operating humidity
SYSTEM
Laser
Signal system
S/N
Dynamic Range
INPUT
Composite video
Audio
OUTPUT
Composite video
S-Video
Audio output (Digital)
Audio output (Analog)
AC Input (via Adapter)
DC 7.2V-12V @ 2A
10W
220mm x 142mm x 40mm
Temperature: 5°C to 35°C
Horizontal
5% to 90%
Semiconductor laser wave length 650nm
PAL/ NTSC
more than 90db
more than 90db
1.0V P-P 75ohm negative sync.
0.5Vrms 47Kohm
1.0V P-P 75ohm negative sync.
(Y) 1.0V P-P 75ohm negative sync.
(C) 0.3V P-P 75ohm negative sync.
0.5V PP 75ohm
0.5Vrms 600 ohm
AC 100V~240V @ 50/60Hz
* Design and specifications are subject to change without notice.
This product incorporates copyright protection technology that is protected by
method claims of certain U.S. patents and other intellectual property rights
owners. Use of this copyright protection technology must be authorized by
Marcrovision Corporation, and is intended for home and other limited viewing
uses only unless otherwise authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and
the double-D symbol are trademarks of Dolby Laboratories. Confidential unpub-
lished works. ©1992-1997 Dolby Laboratories, Inc. All rights reserved.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
jWIN JD-VD745 Operating instructions
- Category
- DVD players
- Type
- Operating instructions
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Lenco MES-230 Owner's manual
-
NextBase SDV685-AC Operating Instructions Manual
-
Medion SDVX7 Series Operating instructions
-
AIRIS M201 Operating instructions
-
-
Eltax HT-153 User manual
-
Curtis DVD6019-B User manual
-
-
Lloyds DVDV816L Operating instructions
-