Carlton EF1000 User manual

Carlton
Brand
Carlton
Model
EF1000
Type
User manual

Carlton EF1000 is an electric fire designed to provide realistic flames and warmth in your home. It features a 15-watt, 230/240-volt bulb that creates the illusion of a coal fire, as well as two heat settings (low and high) that provide up to 2000 watts of heating power. The EF1000 is easy to install and can be plugged into a standard electrical socket. It also has a safety cut-out to prevent overheating and a mains cable that can be positioned to exit from the back or side of the unit. Additionally, the EF1000 comes with a plastic screen and coal to enhance the realistic effect of the flames.

Carlton EF1000 is an electric fire designed to provide realistic flames and warmth in your home. It features a 15-watt, 230/240-volt bulb that creates the illusion of a coal fire, as well as two heat settings (low and high) that provide up to 2000 watts of heating power. The EF1000 is easy to install and can be plugged into a standard electrical socket. It also has a safety cut-out to prevent overheating and a mains cable that can be positioned to exit from the back or side of the unit. Additionally, the EF1000 comes with a plastic screen and coal to enhance the realistic effect of the flames.

SAFETY FIRST SPECIFICATIONS
Do not operate the electric fire with a damaged cord
or plug or after the electric fire malfunctions, has
been dropped or damaged in any manner.
If the power cord becomes damaged, it must be
replaced by your service agent or qualified person to
prevent a hazard. Please contact your local Currys
store for details.
ELECTRIC FIRE
Mains supply: 230-240V
~
50Hz
Output: low heat 1000 watts
high heat 2000 watts
Lamp: 15x2 watts
Flame flicker: 30 watts, <35dB
Width at rear: 400mm
Overall width: 508mm
Height at rear: 535mm
Overall height: 600mm
Depth: 230mm
Because we continually strive to improve our products we may change
specifications and designs without prior notice.
Always position the heater with the plug in an accessible
position.
EF1000
Keep clear of
flammable objects –
Make sure that the plug
is always accessible.
Point the electric fire into
the centre of the room
and away from curtains, furniture, or wall
coverings. Do not use the electric fire in
wardrobes or near fabric or clothing. Do
not stand the electric fire on deep pile car-
pets. Keep the electric fire mains cord clear
of the electric fire.
Do not cover – Use
your electric fire in a
well-ventilated area. Do
not use where
flammable liquids are
used or stored. Do not
use in very dusty areas as dust may
accumulate on the heating elements and
cause overheating.
Do not use in the
bathroom, shower
or near a swimming
pool – Do not use your
electric fire anywhere
where it could be
splashed by water or fall into water.
Do not leave
unattended – Switch
off and unplug the
electric fire when not in
use and do not stand
your electric fire nearer
than 15cm to any flammable object.
Do not allow young
children to play
with your electric
fire – Do not allow
children to open door or
play at the back of the
electric fire.
!
Caution!
Make sure to follow these warnings:
Do not cover the heater. Do not block (even partially) the
front and rear grills of your heater.
Do not leave your heater unattended. Switch off and
unplug your heater when not in use.
Do not touch the knob on the front of the fire. It will
become hot.
Keep your heater free of dust to prevent overheating and
prolong the life of your heater. This can be done with a
vacuum cleaner, using the brush attachment, when the heater
is switched off and unplugged and cooled down.
Do not place your electric fire too close or below an
electrical mains socket.
EF1000 electric fire A3 12/10/99 12:50 pm Page 1
It is recommended that a competent and qualified
builder installs the electric fire.
Position the heater upright on the floor away from curtains, furniture or
wallcoverings.
Installing your electric fire
The electric fire fits into a chimney opening. A
flue is not required, so make sure the flue is
blocked to prevent any draught, as it
may cause the ‘overheating limit’
switch to work incorrectly.
508mm
400 – 440mm
240mm
600mm
540 – 580mm
TROUBLE SHOOTING
INSTALLING YOUR FIRE
My electric fire cuts out
Important. Your heater has a safety cut out, designed to prevent
it working if it becomes too hot.
1
Unplug your heater and allow it to cool down.
2
Inspect your heater. Clean the grills with a vacuum
cleaner if necessary. If there is any sign of physical
damage (e.g. melting or burning of the case) do not
attempt to use your heater. In this case, contact your
nearest store.
3
Let your heater cool down for at least 15 minutes.
4
The heater can then be switched on again.
My electric fire does not
work when I turn it on
1
Check that your heater is plugged in and the power is
turned on to the socket.
2
Try replacing the fuse in the plug.
3
Check the wiring in the plug.
4
If your heater still doesn't work, please contact your
nearest store.
Plug your heater into a standard electrical
socket (230-240 Volt 13 Amp rated).
Realistic flames
Your electric fire gives the impression of a real coal fire. To achieve the realistic
flames electric fans are used which may cause a small residual noise when
switched on.
Use the switch on the lefthand of
the electric fire to switch to no
heat, low heat or high heat.
Use the switch on the right
of the electric fire to switch it
on or off.
You can position the mains cable to exit
out of the electric fire from the back or
from the side. It is important to make
sure that the grommet and the cable tie
is securely in place to prevent the cable
from being damaged.
Mains cable location
no heat
low
heat
high
heat
Electric
fire off
Electric
fire on
grommet
cable tie
Put the plastic screen
in front of the electric
lamps. Place the
lumps of coal into the
fire to look like a real
coal fire. Make sure
young children do not
handle the coal.
Laying the coal
Electric lamps
replacement
UNPLUG FROM THE MAINS.
Allow the electric fire to cool.
Remove the coal and the
plastic screen. Rotate the faulty
lamp anti-clockwise to remove.
Replace with new 15 watt
230/240 volt bulb. Replace
plastic screen and coal.
FEATURES
Fire goes
inside
chimney
opening
Front
cover
Screw main
frame into
wall
Main
frame
How to install electric fire
1 Prepare a chimney opening space as shown in diagram.
2 Detach the front cover and put the electric fire in opening.
3 Mark the position of the four screw holes on the wall then remove the
electric fire from opening.
4 Drill four holes where you made the marks and insert raw plugs provided.
5 Relocate the electric fire into the opening and fix it with the screws provided.
6 Attach the front cover on the main frame.
EF1000 electric fire A3 12/10/99 12:50 pm Page 2
  • Page 1 1
  • Page 2 2

Carlton EF1000 User manual

Carlton
Brand
Carlton
Model
EF1000
Type
User manual

Carlton EF1000 is an electric fire designed to provide realistic flames and warmth in your home. It features a 15-watt, 230/240-volt bulb that creates the illusion of a coal fire, as well as two heat settings (low and high) that provide up to 2000 watts of heating power. The EF1000 is easy to install and can be plugged into a standard electrical socket. It also has a safety cut-out to prevent overheating and a mains cable that can be positioned to exit from the back or side of the unit. Additionally, the EF1000 comes with a plastic screen and coal to enhance the realistic effect of the flames.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents