Behringer ULTRAGRAPH FBQ-PRO FBQ3102 Quick start guide

Brand: Behringer

Model: ULTRAGRAPH FBQ-PRO FBQ3102

Category: DJ controllers

Type: Quick start guide

This manual is also suitable for

(Check Out behringer.com for Full Manual)

ULTRAGRAPH PRO

FBQ6200/FBQ3102/FBQ1502

Audiophile 31-Band and 15-Band Stereo Graphic Equalizer

with FBQ Feedback Detection System

2 ULTRAGRAPH PRO FBQ6200/FBQ3102/FBQ1502 Quick Start Guide 3

Important Safety

Instructions

LIMITED WARRANTY

LEGAL DISCLAIMER

Terminals marked with this symbol carry

electrical current of su cient magnitude

to constitute risk of electric shock.

Use only high-quality professional speaker cables with

¼" TS or twist-locking plugs pre-installed. Allother

installation or modi cation should be performed only

by quali edpersonnel.

This symbol, wherever it appears,

alertsyou to the presence of uninsulated

dangerous voltage inside the

enclosure-voltage that may be su cient to constitute a

risk ofshock.

This symbol, wherever it appears,

alertsyou to important operating and

maintenance instructions in the

accompanying literature. Please read the manual.

Caution

To reduce the risk of electric shock, donot

remove the top cover (or the rear section).

No user serviceable parts inside. Refer servicing to

quali ed personnel.

Caution

To reduce the risk of  re or electric shock,

do not expose this appliance to rain and

moisture. The apparatus shall not be exposed to dripping

or splashing liquids and no objects  lled with liquids,

suchas vases, shall be placed on the apparatus.

Caution

These service instructions are for use

by quali ed service personnel only.

Toreduce the risk of electric shock do not perform any

servicing other than that contained in the operation

instructions. Repairs have to be performed by quali ed

servicepersonnel.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as

radiators, heat registers, stoves, or other apparatus

(including ampli ers) that produce heat.

9. Do not defeat the safety purpose of the polarized

or grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding-type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. Ifthe

provided plug does not  t into your outlet, consult an

electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11. Use only attachments/accessories speci ed by

themanufacturer.

12. Use only with the

cart, stand, tripod, bracket,

or table speci ed by the

manufacturer, orsold with

the apparatus. When a cart

is used, use caution when

moving the cart/apparatus

combination to avoid

injury from tip-over.

13. Unplug this apparatus during lightning storms or

when unused for long periods of time.

14. Refer all servicing to quali ed service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power supply cord or plug

is damaged, liquid has been spilled or objects have fallen

into the apparatus, the apparatus has been exposed

to rain or moisture, does not operate normally, or has

beendropped.

15. The apparatus shall be connected to a MAINS socket

outlet with a protective earthing connection.

16. Where the MAINS plug or an appliance coupler is

used as the disconnect device, the disconnect device shall

remain readily operable.

TECHNICAL SPECIFICATIONS AND APPEARANCES

ARE SUBJECT TO CHANGE WITHOUT NOTICE AND

ACCURACY IS NOT GUARANTEED. BEHRINGER IS

PART OF THE MUSIC GROUP MUSICGROUP.COM.

ALL TRADEMARKS ARE THE PROPERTY OF THEIR

RESPECTIVE OWNERS. MUSICGROUP ACCEPTS NO

LIABILITY FOR ANY LOSS WHICH MAY BE SUFFERED

BY ANY PERSON WHO RELIES EITHER WHOLLY OR

IN PART UPON ANY DESCRIPTION, PHOTOGRAPH

OR STATEMENT CONTAINED HEREIN. COLORS AND

SPECIFICATIONS MAY VARY FROM ACTUAL PRODUCT.

MUSIC GROUP PRODUCTS ARE SOLD THROUGH

AUTHORIZED FULLFILLERS AND RESELLERS ONLY.

FULLFILLERSAND RESELLERS ARE NOT AGENTS OF

MUSICGROUP AND HAVE ABSOLUTELY NO AUTHORITY

TO BIND MUSICGROUP BY ANY EXPRESS OR IMPLIED

UNDERTAKING OR REPRESENTATION. THIS MANUAL

IS COPYRIGHTED. NO PART OF THIS MANUAL MAY

BE REPRODUCED OR TRANSMITTED IN ANY FORM

OR BY ANY MEANS, ELECTRONIC OR MECHANICAL,

INCLUDING PHOTOCOPYING AND RECORDING OF ANY

KIND, FOR ANY PURPOSE, WITHOUT THE EXPRESS

WRITTEN PERMISSION OF MUSICGROUPIPLTD.

Trident Chambers, Wickhams Cay, P.O. Box 146,

Road Town, Tortola, British Virgin Islands

§ 1 Warranty

(1) This limited warranty is valid only if you purchased

the product from a MUSIC Group Authorized Reseller in

the country of purchase. A list of authorized resellers can

be found on BEHRINGER’s website behringer. com under

“Where to Buy”, or you can contact the MUSIC Group o

closest to you.

(2) MUSICGroup* warrants the mechanical and

electronic components of this product to be free of defects

in material and workmanship if used under normal

operating conditions for a period of one (1) year from

the original date of purchase (see the Limited Warranty

terms in §4 below), unless a longer minimum warranty

period is mandated by applicable local laws. If the product

shows any defects within the speci ed warranty period

and that defect is not excluded under §4, MUSICGroup

shall, at its discretion, either replace or repair the product

using suitable new or reconditioned product or parts.

Incase MUSICGroup decides to replace the entire product,

thislimited warranty shall apply to the replacement

product for the remaining initial warranty period, i.e.,

one (1) year (or otherwise applicable minimum warranty

period) from the date of purchase of the original product.

(3) Upon validation of the warranty claim, the repaired

or replacement product will be returned to the user

freight prepaid by MUSICGroup.

(4) Warranty claims other than those indicated above

are expressly excluded.

PLEASE RETAIN YOUR SALES RECEIPT. IT IS YOUR PROOF

OF PURCHASE COVERING YOUR LIMITED WARRANTY.

THIS LIMITED WARRANTY IS VOID WITHOUT SUCH PROOF

OFPURCHASE.

§ 2 Online registration

Please do remember to register your new BEHRINGER

equipment right after your purchase at behringer. com

under “Support” and kindly read the terms and conditions

of our limited warranty carefully. Registeringyour

purchase and equipment with us helps us process

your repair claims quicker and more e ciently.

Thankyouforyour cooperation!

§ 3 Return materials authorization

(1) To obtain warranty service, please contact the

retailer from whom the equipment was purchased.

Should your MUSIC Group Authorized Reseller not be

located in your vicinity, you may contact the MUSICGroup

Authorized Ful ller for your country listed under

“Support” at behringer. com. Ifyour country is not

listed, please check if your problem can be dealt with

by our “OnlineSupport” which may also be found under

“Support” at behringer. com. Alternatively,please submit

an online warranty claim at behringer. com BEFORE

returning the product. All inquiries must be accompanied

by a description of the problem and the serial number

of the product. Afterverifying the product’s warranty

eligibility with the original sales receipt, MUSICGroup

will then issue a ReturnMaterials Authorization

(“RMA”)number.

(2) Subsequently, the product must be returned in

its original shipping carton, together with the return

authorization number to the address indicated by

MUSICGroup.

(3) Shipments without freight prepaid will not

beaccepted.

§ 4 Warranty Exclusions

(1) This limited warranty does not cover consumable

parts including, but not limited to, fuses and batteries.

Where applicable, MUSICGroup warrants the valves or

meters contained in the product to be free from defects

in material and workmanship for a period of ninety (90)

days from date of purchase.

(2) This limited warranty does not cover the product

if it has been electronically or mechanically modi ed

in any way. If the product needs to be modi ed or

adapted in order to comply with applicable technical

or safety standards on a national or local level, inany

country which is not the country for which the

product was originally developed and manufactured,

thismodi cation/adaptation shall not be considered a

defect in materials or workmanship. Thislimited warranty

does not cover any such modi cation/adaptation,

regardless of whether it was carried out properly or not.

Under the terms of this limited warranty, MUSICGroup

shall not be held responsible for any cost resulting from

such a modi cation/adaptation.

(3) This limited warranty covers only the product

hardware. It does not cover technical assistance for

hardware or software usage and it does not cover

any software products whether or not contained in

the product. Any such software is provided “AS IS”

unless expressly provided for in any enclosed software

limitedwarranty.

(4) This limited warranty is invalid if the

factory- appliedserial number has been altered or

removed from theproduct.

(5) Free inspections and maintenance/repair work

are expressly excluded from this limited warranty,

inparticular, if caused by improper handling of the

product by the user. This also applies to defects caused

by normal wear and tear, in particular, of faders,

crossfaders, potentiometers, keys/buttons, guitar strings,

illuminantsand similar parts.

(6) Damage/defects caused by the following conditions

are not covered by this limited warranty:

• improper handling, neglect or failure to operate the

unit in compliance with the instructions given in

BEHRINGER user or service manuals;

• connection or operation of the unit in any way

that does not comply with the technical or safety

regulations applicable in the country where the

product is used;

• damage/defects caused by acts of God/Nature

(accident,  re,  ood, etc) or any other condition that

is beyond the control of MUSICGroup.

(7) Any repair or opening of the unit carried out by

unauthorized personnel (user included) will void the

limitedwarranty.

(8) If an inspection of the product by MUSICGroup

shows that the defect in question is not covered by the

limited warranty, the inspection costs are payable by

thecustomer.

(9) Products which do not meet the terms of this

limited warranty will be repaired exclusively at the buyer’s

expense. MUSICGroup or its authorized service center will

inform the buyer of any such circumstance. If the buyer

fails to submit a written repair order within 6 weeks after

noti cation, MUSICGroup will return the unit C.O.D. with

a separate invoice for freight and packing. Such costs will

also be invoiced separately when the buyer has sent in a

written repair order.

(10) MUSIC Group Authorized Resellers do not sell new

products directly in online auctions. Purchasesmade

through an online auction are on a “buyer beware” basis.

Online auction con rmations or sales receipts are not

accepted for warranty veri cation and MUSICGroup will

not repair or replace any product purchased through an

online auction.

§ 5 Warranty transferability

This limited warranty is extended exclusively to the

original buyer (customer of authorized reseller) andis

not transferable to anyone who may subsequently

purchase this product. No other person (reseller,etc.)

shallbe entitled to give any warranty promise on behalf

of MUSICGroup.

§ 6 Claim for damage

Subject only to the operation of mandatory applicable

local laws, MUSICGroup shall have no liability to the buyer

under this warranty for any consequential or indirect

loss or damage of any kind. In no event shall the liability

of MUSICGroup under this limited warranty exceed the

invoiced value of the product.

§ 7 Limitation of liability

This limited warranty is the complete and exclusive

warranty between you and MUSICGroup. It supersedes

all other written or oral communications related to this

product. MUSICGroup provides no other warranties for

this product.

§ 8 Other warranty rights and

nationallaw

(1) This limited warranty does not exclude or limit the

buyer’s statutory rights as a consumer in any way.

(2) The limited warranty regulations mentioned herein

are applicable unless they constitute an infringement of

applicable mandatory local laws.

(3)

This warranty does not detract from the seller’s

obligations in regard to any lack of conformity of the

product and any hidden defect.

§ 9 Amendment

Warranty service conditions are subject to change without

notice. For the latest warranty terms and conditions

and additional information regarding MUSICGroup’s

limited warranty, please see complete details online at

behringer. com.

* MUSICGroup Macao Commercial O shore Limited of

RuedePequim No. 202-A, Macau Finance Centre 9/J, Macau,

including all MUSICGroup companies

Page is loading ...

12 13ULTRAGRAPH PRO FBQ6200/FBQ3102/FBQ1502 Quick Start Guide

ULTRAGRAPH PRO FBQ6200/FBQ3102/FBQ1502 Controls

(1) (10)(8) (9)(3)

(5)(4) (6)

(15)

(11) (17)(16)

(12)

(14)

(4)

(3)(1)

(6)(5) (7) (8)

(2)

(9)

(12)

(10)

(13) (16) (17)(11) (15)

(14)

(19) (21)

(8)(26) (25)

(22)

(1) (23)

(20)(18) (7)

(2) (9)

(3)

(4) (5) (6) (24)

(12) (13) (16) (17)

(10)

(11) (15)

(14)

14 15ULTRAGRAPH PRO FBQ6200/FBQ3102/FBQ1502 Quick Start Guide

ULTRAGRAPH PRO FBQ6200/FBQ3102/FBQ1502 Controls

(1) The INPUT/OUTPUT LEVEL METER lets you keep an

eye on the signal level in order to avoid distortion.

Depending on the position of the I/O METER IN/OUT

switch (2) , the display shows either the input or the

output signal (switchdepressed) level. When the

signal level reaches roughly +18 dB, thatis, 3dBbelow

clipping starts to occur, the red CLIP LED lights up.

The level meter on the FBQ1502 displays only the

output signal level.

(2) The I/O METER IN/OUT switch lets you alternate

between displaying the input and the output signal

level. When the switch is depressed, the output signal

level is shown. The FBQ1502 does not feature this switch.

(3) When you press the FBQ switch, the FBQ feedback

detection system is activated. The frequency

(or frequen cies) that evoke feedback is/are indicated by

means of a lighted fader LED. All other LEDs are toned

down. Now, simply lower the respective frequency range

somewhat until you eliminate the feedback and the LED

no longer lights up.

(4) The AUDIO IN/OUT switch is used to enable or disable

the entire equalizer section. The FBQ1502 does this

electronically, while the FBQ3102 and the FBQ6200

feature a relay-driven hard bypass function. As long

as the switch is not depressed or while the equalizer is

not powered up, the inputs and the outputs are directly

connected to one another. The AUDIO IN/OUT switch is

used to alternate between A and B, i.e. to compare the

original unprocessed signal with the processed signal.

(5) The INPUT control is used to adjust the input signal

level. You can boost/attenuate the signal level from

+15 to -15 dB.

(6) The LOW CUT control is used to adjust the lower cut-o

frequency of your ULTRAGRAPH PRO. The high-pass

lter (18 dB/oct.) covers the range between 10 and

400 Hz, whereby the lter lets the signal pass through

unprocessed, when the control is in the 10 Hz position.

The FBQ1502 features a switchable high-pass lter

(LOW CUT) instead of a low cut control, and its cut-o

frequency is 25 Hz.

(7) The HIGH CUT control is used to adjust the upper cut-o

frequency of your ULTRAGRAPH PRO. The low-pass

lter (18 dB/oct.) covers the range between 2.5 and

30 kHz, whereby the lter lets the signal pass through

unprocessed when the control is in the 30 kHz position.

(8) The RANGE switch lets you alternate between the

maximum value of lowering/increasing of individual

frequencies from 12 dB to 6 dB (switchdepressed).

(9) These are the 31 SLIDING CONTROLS

(FBQ1502: 15 sliding controls per channel) for individual

frequency bands. When in “0” position, the particular

frequency range is not processed at all. To boost a

frequency range, pull the sliding control upward;

to attenuate, pull the sliding control downward.

(10) The POWER switch powers up your ULTRAGRAPH PRO.

The POWER switch should always be in the “O” position

when you are about to connect your FBQ to the mains.

(11) The connection to the mains is done via a standard

IEC connector. Amatching cable is included.

(12) FUSE COMPARTMENT/VOLTAGE SELECTION.

(13) SERIAL NUMBER.

(14) INPUT. These are the audio inputs of the FBQ3102.

All three equalizers in the series feature the same input

and output connectors in the form of balanced ¼" TRS

and XLR connectors.

(15) OUTPUT. These are the audio outputs.

The ¼" connectors and their respective

XLR connectors are wired in parallel.

(16) SUB OUT. This balanced XLR connector provides the

output signal for your subwoofer. A summed up mono

signal for the subwoofer is provided here.

(17) Use the X-OVER FREQ control to select the desired

crossover frequency for thesubwoofer.

(18) The ULTRAGRAPH PRO FBQ6200 features a built-in

limiter for each channel. Use the LIMITER switch

for its activation.

(19) The limiter display informs you about the amount of

gain reduction perfomed by the limiter.

(20) The limiter connes the signal to an adjustable

signal level. Use the THRESHOLD control to adjust

the threshold value of the limiter from -6to +22 dB.

When the control is in the “-6 dB” setting, the gain

reduction is very pronounced; the more you turn the

control toward “+22 dB”, the gain reduction is lower.

When the threshold control is in its right-most position,

the limiter is not applied.

(21) Activate the pink noise generator by using the

PINK NOISE switch. Thebuilt-in switch illumination

blinks red when the pink noise generator isactivated.

(22) Read o the noise generator’s signal level on

the LED display.

(23) Use the NOISE LEVEL control to adjust the volume

of the pink noise yougenerate.

(24) The LED display indicates the signal level present at the

SUB OUT connector.

(25) The signal level present at the subwoofer output

connector can be adjusted by using the LEVEL control.

(26) To activate the subwoofer output, please depress the

SUBWOOFER switch.

Check Out behringer.com for Full Manual

(1) El MEDIDOR DEL NIVEL DE ENTRADA/SALIDA

le permite vigilar el nivel de señal para evitar la

distorsión por sobreconducción. Dependiendo de la

posición del interruptor I/O METER IN/OUT, el display

muestra o bien el nivel de señal de entrada o la de

salida (interruptor pulsado). Cuando el nivel de

señal alcance aproximadamente los +18 dB, es decir,

3 dB por debajo de que empiece a haber cortes,

el CLIP-LED rojo se encenderá. El display de

distorsión del FBQ1502 muestra sólo los valores

de la señal de salida.

(2) El interruptor I/O METER IN/OUT le permite alternar

entre mostrar e nivel de señal en la entrada o en la

salida. Cuando el interruptor esté pulsado, se mostrará

el nivel de señal de salida. El FBQ1502 no dispone de

esteinterruptor.

(3) Cuando presione el interruptor FBQ, el sistema

de detección de realimentación FBQ se activa.

La frecuencia (o frecuencias) que evocan la

realimentación está/n indicada/s por medio de

un LED iluminado. El resto de los LEDs estarán

apagados. Simplemente tiene que ir reduciendo

el rango de frecuencia respectivo hasta que elimine

la realimentación y hasta que el LED se apague.

(4) El interruptor AUDIO IN/OUT se utiliza para conectar

o desconectar toda una sección del ecualizador en un

canal de audio. El FBQ1502 lo hace electrónicamente,

mientras que el FBQ3102 y el FBQ6200 disponen de

una función de bypass por relés. Mientras que el

interruptor no esté pulsado o mientras el ecualizador

no esté encendido, las entradas y salidas están

directamente conectadas unas a otras. El interruptor

AUDIO IN/OUT se usa para alternar entre A y

B, es decir, para comparar la señal original no

procesada y la procesada.

(5) El control de INPUT se usa para ajustar el nivel de señal

de entrada. Puedeincrementar/atenuar el nivel de

señal de +15 a -15 dB.

(6) El control LOW/CUT se usa para ajustar la frecuencia

de corte más baja de su ULTRAGRAPH PRO. El ltro

de high-pass (18 dB/oct.) cubre el rango entre 10y

400 Hz, mientras que el ltro permite a la señal no

procesada pasar cuando el control está en la posición

de 10 Hz. El FBQ1502 dispone de un ltro high-pass

contectable (LOW CUT) en lugar de un control de corte

bajo, ysu frecuencia de corte es de 25 Hz.

(7) El control HIGH CUT se usa para ajustar la frecuencia

de corte más alta de su ULTRAGRAPH PRO. El ltro

low-pass (18 dB/oct.) cubre el rango entre 2,5 y 30kHz,

mientras que el ltro permite a la señal no procesada

pasar cuando el control está en la posición de 30 kHz.

(8) El interruptor RANGE le permite alternar entre el

valor máximo de aumentar/disminuir los rangos

de frecuencia individuales entre 12 dB a 6 dB

(interruptor pulsado).

(9) Estos son los 31 SLIDING CONTROLS

(FBQ1502: 15 controles de deslizamiento por canal)

para rangos de frecuencia individuales. Cuando se

encuentran en posición “0”, el rango de frecuencia

particular no se procesa. Paraincrementar un

rango de frecuencia, deslice el control hacia arriba;

paraatenuarlo, deslícelo hacia abajo.

(10) El interruptor POWER conecta su ULTRAGRAPH PRO.

El conmutador POWER debe encon trarse en la

posición de “apagado” (no presionado) cuando realice

la conexión a la red de corriente.

(11) La conexión a red se realiza mediante una toma de tres

espigas IEC. En el suministro se incluye un cable de

red adecuado.

(12) PORTAFUSIBLES/SELECCIÓN DE TENSIÓN.

(13) NÚMERO DE SERIE.

(14) INPUT. Son las entradas de audio de su FBQ3102.

Los tres ecualizadores de esta serie disponen de los

mismos conectores de entrada y salida en la forma de

conectores balanceados de 6,3 mm TRS y XLR.

(15) OUTPUT. Son las salidas de audio. Los conectores

de 6,3mm y sus conectores XLR respectivos están

cableados en paralelo.

(16) SUB OUT. La señal de salida para el subwoofer está

situada en este conector balanceado XLR. Una señal

mono es creada combinando los dos canales estéreo

para el subwoofer.

(17) Use el control X-OVER FREQ para seleccionar el

frecuencia crossover deseada para el subwoofer.

(18) El ULTRAGRAPH PRO FBQ6200 dispone de un

limitador para cada canal. Useel interruptor

LIMITER para activarlo.

(19) El display del limitador le informa del nivel de

reducción de ganancia que genera el limitador.

(20) El limitador constriñe la señal a un nivel de señal

ajustable. Use el control THRESHOLD para ajustar

el nivel de umbral del limitador de -6 a +22 dB.

Cuando en control está en la posición de “+6 dB”,

la reducción de ganancia es muy pronunciada;

cuanto más gire el control hacia “+22 dB”, la reducción

de ganancia será menor. Cuando el control de umbral

está girado totalmente hacia la derecha, el limitador

está desconectado.

(21) Active el generador de ruido rosa usando el interruptor

PINK NOISE. Elinterruptor parpadeará en rojo cuando

el generador esté activado.

(22) Vea el nivel de señal del generador de ruido rosa en el

diplay de LEDs.

(23) Utilice el control NOISE LEVEL para ajustar el volumen

del ruido rosa quegenere.

(24) El diplay LED del Subwoofer indica el nivel de señal

presente en el conector de salida SUB OUT.

(25) El nivel de señal presente en el conector de salida del

subwoofer puede ajustarse usando el control LEVEL.

(26) Para activar la salida del subwoofer, pulse el

interruptor SUBWOOFER.

Si quiere acceder al manual de

instrucciones completo, vaya a la

página web behringer.com

(ES) Controles(EN) Controls

Page is loading ...

20 ULTRAGRAPH PRO FBQ6200/FBQ3102/FBQ1502 Quick Start Guide 21

Specications

FBQ6200 FBQ3102 FBQ1502

Audio Inputs

Inputs RF-ltered, servo-balanced XLR and ¼" TRS connectors

Impedance 40 kW balanced and unbalanced

Maximum input level +21 dBu balanced and unbalanced

CMRR typ. 40 dB, >55 dB @ 1 kHz

Audio Outputs

Outputs servo-balanced XLR and ¼" TRS connectors

Subwoofer Out

balanced XLR connector,

level variable o to 0 dB

balanced XLR connector balanced XLR connector

Crossover frequency variable, 30 - 200 Hz

System Specications

Frequency response 10 Hz to 30 kHz, ±3 dB

S/N ratio 22 Hz to 22 kHz >94 dB @ +4 dBu

Distortion (THD) typ. 0.006% @ +4 dBu, 1 kHz, Gain 1

Crosstalk typ. -65 dB @ 1kHz

Roll-O Filter Section

Type 12 dB/oct., Butterworth

Input variable (-15 dB to +15 dB)

Low Cut variable (10 Hz to 400 Hz) variable (10 Hz to 400 Hz) switchable, Cuto @ 25 Hz

High Cut variable (2.5 kHz to 30 kHz) variable (2.5 kHz to 30 kHz) —

Graphic Equalizer

Type analog 31-band equalizer analog 31-band equalizer analog 15-band equalizer

Frequency range

20 Hz to 20 kHz in 31 1/3-octave bands

(ISO frequencies)

20 Hz to 20 kHz in 31 1/3-octave bands

(ISO frequencies)

20 Hz to 16 kHz in 15 bands (ISO frequencies)

Bandwidth 1/3 octave 1/3 octave 2/3 octave

Control range ±6 dB or ±12 dB (switchable)

Limiter Section

Attack/Release 20 msec / 90 msec — —

Threshold variable, -6 dB to +22 dB (o) — —

LED meter Gain reduction 20/10/3/1 dB — —

Noise Generator

Type Pink noise, level variable, o to 0 dBu, — —

LED level meter -24/-12/-6/0 dB — —

Function Switches

FBQ activates the FBQ Feedback Detection System

Audio In/Out switch to bypass the equalizer functions

I/O Meter In/Out

switches the meter display

from input to output

switches the meter display

from input to output

—

Range shift of the maximum cut/boost range for all 31/15 bands

Low Cut — — activates the high pass lter

Limiter activates the limiter — —

Pink Noise activates the noise generator — —

Subwoofer activates the subwoofer output — —

FBQ6200 FBQ3102 FBQ1502

Indicators

Input/output level

8-segment LED display:

-24/-18/-12/-6/0/+6/+12 dB/CLIP

12-segment LED display:

-30/-24/-18/-12/-6/-3/0/+3/+6/+9

+12 dB/CLIP

4-segment LED display:

-20/0/+6 dB/CLIP (output only)

Subwoofer 4-segment LED display: -18/-12/0/+12 dB — —

Power Supply

Mains Voltage

USA / Canada 120 V~, 60 Hz

Europe / U.K. / Australia 230 V~, 50 Hz

Japan 100 V~, 50 - 60 Hz

general export model 120/230 V~, 50 - 60 Hz

Power consumption 22 W

Fuse 100 - 120 V~: T 630 mA H / 200 - 240 V~: T 315 mA H

Mains connection standard IEC receptacle

Dimensions / Weight

Dimensions (H x W x D)

approx. 5.90 x 5.23 x 18.97"

approx. 150 x 133 x 482.0 mm

approx. 5.90 x 3.50 x 18.99"

approx. 150 x 89 x 482.6 mm

approx. 8.46 x 1.75 x 18.99"

approx. 215 x 44.5 x 482.6 mm

Weight

approx. 6.70 lbs

approx. 3.04 kg

approx. 5.82 lbs

approx. 2.64 kg

approx. 5.15 lbs

approx. 2.34 kg

Page is loading ...

Quick Start Guide 3130 ULTRAGRAPH PRO FBQ6200/FBQ3102/FBQ1502

Other important information

1. Register online. Please register your new

MUSIC Group equipment right after you purchase it by

visiting behringer. com. Registering your purchase using

our simple online form helps us to process your repair

claims more quickly and eciently. Also, read the terms

and conditions of our warranty, ifapplicable.

2. Malfunction. Should your MUSICGroup

Authorized Reseller not be located in your vicinity, you

may contact the MUSIC Group Authorized Fulller for

your country listed under “Support” at behringer. com.

Shouldyour country not be listed, please check if your

problem can be dealt with by our “OnlineSupport” which

may also be found under “Support” at behringer. com.

Alternatively, please submit an online warranty claim at

behringer. com BEFORE returning theproduct.

3. Power Connections. Before plugging the

unit into a power socket, please make sure you are using

the correct mains voltage for your particular model.

Faultyfuses must be replaced with fuses of the same

typeand rating without exception.

1. Registro online. Le recomendamos que

registre su nuevo aparato MUSIC Group justo después de

su compra accediendo a la página web behringer. com.

Elregistro de su compra a través de nuestro sencillo

sistema online nos ayudará a resolver cualquier

incidencia que se presente a la mayor brevedad posible.

Además,aproveche para leer los términos y condiciones de

nuestra garantía, si es aplicable en sucaso.

2. Averías. En el caso de que no exista un distribuidor

MUSIC Group en las inmediaciones, puede ponerse en

contacto con el distribuidor MUSIC Group de su país,

queencontrará dentro del apartado “Support” de nuestra

página web behringer. com. En caso de que su país no

aparezca en ese listado, acceda a la sección “Online Support”

(quetambiénencontrará dentro del apartado “Support” de

nuestra páginaweb) y compruebe si su problema aparece

descrito y solucionado allí. De forma alternativa, envíenos a

través de la página web una solicitud online de soporte en

periodo de garantía ANTES de devolvernos el aparato.

3. Conexiones de corriente. Antes de enchufar

este aparato a una salida de corriente, asegúrese de que dicha

salida sea del voltaje adecuado para su modelo concreto.

En caso de que deba sustituir un fusible quemado, deberá

hacerlo por otro de idénticas especicaciones, sinexcepción.

1. Enregistrez-vous en ligne. Prenez le

temps d’enregistrer votre produit MUSIC Group aussi vite

que possible sur le site Internet behringer. com. Le fait

d’enregistrer le produit en ligne nous permet de gérer

les réparations plus rapidement et plus ecacement.

Prenezégalement le temps de lire les termes et conditions

de notre garantie.

2. Dysfonctionnement. Si vous n’avez pas de

revendeur MUSIC Group près de chez vous, contactez le

distributeur MUSIC Group de votre pays: consultez la liste

des distributeurs de votre pays dans la page “Support” de

notre site Internet behringer. com. Si votre pays n’est pas

dans la liste, essayez de résoudre votre problème avec

notre “aideen ligne” que vous trouverez également dans

la section “Support” du site behringer. com. Vous pouvez

également nous faire parvenir directement votre demande

de réparation sous garantie par Internet sur le site

behringer. com AVANT de nous renvoyer le produit.

3. Raccordement au secteur. Avant de relier

cet équipement au secteur, assurez-vous que la tension

secteur de votre région soit compatible avec l’appareil.

Veillez à remplacer les fusibles uniquement par des

modèles exactement de même taille et de même valeur

électrique — sans aucune exception.

1. Online registrieren. Bitte registrieren Sie Ihr

neues MUSIC Group-Gerät direkt nach dem Kauf auf der

Website behringer. com. Wenn Sie Ihren Kauf mit unserem

einfachen online Formular registrieren, können wir Ihre

Reparaturansprüche schneller und ezienter bearbeiten.

Lesen Sie bitte auch unsere Garantiebedingungen,

fallszutreend.

2. Funktionsfehler. Sollte sich kein MUSICGroup

Händler in Ihrer Nähe benden, können Sie den

MUSICGroup Vertrieb Ihres Landes kontaktieren,

derauf behringer. com unter „Support“ aufgeführt ist.

Sollte Ihr Land nicht aufgelistet sein, prüfen Sie bitte,

ob Ihr Problem von unserem „Online Support“ gelöst

werden kann, den Sie ebenfalls auf behringer. com unter

„Support“ nden. Alternativ reichen Sie bitte Ihren

Garantieanspruch online auf behringer. com ein, BEVOR Sie

das Produktzurücksenden.

3. Stromanschluss. Bevor Sie das Gerät an

eine Netzsteckdose anschließen, prüfen Sie bitte, obSie

die korrekte Netzspannung für Ihr spezielles Modell

verwenden. Fehlerhafte Sicherungen müssen ausnahmslos

durch Sicherungen des gleichen Typs und Nennwerts

ersetztwerden.

1. Registre-se online. Por favor, registre seu

novo equipamento MUSIC Group logo após a compra

visitando o site behringer. com Registrar sua compra

usando nosso simples formulário online nos ajuda a

processar seus pedidos de reparos com maior rapidez e

eciência. Além disso, leia nossos termos e condições de

garantia, caso seja necessário.

2. Funcionamento Defeituoso.

Casoseufornecedor MUSIC Group não esteja localizado

nas proximidades, você pode contatar um distribuidor

MUSIC Group para o seu país listado abaixo de “Suporte”

embehringer. com. Se seu país não estiver na lista,

favorchecar se seu problema pode ser resolvido com o

nosso “Suporte Online” que também pode ser achado

abaixo de “Suporte”em behringer. com. Alternativamente,

favor enviar uma solicitação de garantia online em

behringer. com ANTES da devolução do produto.

3. Ligações. Antes de ligar a unidade à tomada,

assegure-se de que está a utilizar a voltagem correcta para

o modelo em questão. Os fusíveis com defeito terão de

ser substituídos, sem qualquer excepção, por fusíveis do

mesmo tipo e corrente nominal.

Important information

Aspectos importantes

Informations importantes

Wegitere wichtige

Informationen

Outras Informações

Importantes

We Hear You

Behringer ULTRAGRAPH FBQ-PRO FBQ3102 Quick start guide

Brand: Behringer

Model: ULTRAGRAPH FBQ-PRO FBQ3102

Category: DJ controllers

Type: Quick start guide

This manual is also suitable for

Download PDF

report

in other languages

français: Behringer ULTRAGRAPH FBQ-PRO FBQ3102 Guide de démarrage rapide
español: Behringer ULTRAGRAPH FBQ-PRO FBQ3102 Guía de inicio rápido
Deutsch: Behringer ULTRAGRAPH FBQ-PRO FBQ3102 Schnellstartanleitung
português: Behringer ULTRAGRAPH FBQ-PRO FBQ3102 Guia rápido

Behringer ULTRAGRAPH FBQ-PRO FBQ3102 Quick start guide

This manual is also suitable for

Behringer ULTRAGRAPH FBQ-PRO FBQ3102 Quick start guide

in other languages

Related papers

Other documents