ProTemp PT-033-230 User's Manual And Operating Instructions

Model #’s: PT-02-230, PT-033-230,

PT-033-230, PT-05-400, PT-09-400

User’s Manual and

Operating Instructions

Electric Fan Heater

Do not operate this heater until you have read, and

thoroughly understand these safety and operating

instructions. Failure to comply with the precautions and

instructions provided with this heater can result in death,

serious bodily injury, property loss or damage from the

hazards of fire, explosion, burns, or electric shock. Only

persons who can read and understand these instructions

should use or service this heater. Not for recreational

vehicle use.

821000175-11

CONSUMER: Retain this manual for future reference.

Table of Contents

English ................................................................. 2-3

Spanish................................................................. 4-5

French ................................................................. 6-7

Dutch .................................................................. 8-9

Exploded View and Parts List............................ 10-11

Page 2 EN Electric Fan Heater User’s Manual

Introduction

Electric Fan Heater

NEVER LEAVE HEATER

UNATTENDED WHILE BURN-

ING, OR WHILE CONNECTED

TO A POWER SOURCE.

- At first turn the thermostat to “Max” and let the

heater operate with full power input. When the

room temperature reaches the required value, turn

the thermostat to the left until it switches off.

- The thermostat will then switch on and off auto-

matically to control the room temperature

according to the preset value and to keep the

room temperature constant.

- When using the heater for the first time, you may

notice a slight emission of smoke. This is quite

normal and it stops after a short time. The heating

element is made of steel and was coated with a

layer of protective oil during production. The

smoke is caused by the leftover oil as it is heated.

Technical Specifications

Specifications subject to change without notice

Thermostat Instructions

- The fan heater is not suitable for use outdoors in

damp weather, in bathrooms or in other wet or

damp environments.

- Please note that the fan heater can become very

hot and should, therefore, be placed at a safe

distance from flammable objects such as furniture,

curtains and similar objects.

- Do not cover the fan heater.

- Do not place the fan heater immediately under a

wall outlet.

- Do not connect the fan heater using an on/off timer

or other equipment which can automatically switch

the device on.

- The fan heater must not be placed in rooms where

flammable liquids or gases are used or stored.

- If an extension cable is used, it must be as short

as possible and must always be fully extended.

- Children should be supervised to ensure that they

do not play with the appliance. The appliance in

not intended for use by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge.

If the appliance is damaged, do not use it any

more.

Special Safety Regulations

Model Voltage / Hz Power

Rating

Settings Temp Fuse

requirement

Dims Weight

PT-02-230 230V~50Hz 2,000

4 (OFF, 650W,

1300W, 2000W)

continuously

adjustable 0-85°C

10A

197x210x303

mm

4.2 kg

PT-033-230 230V~50Hz 3,300

4 (OFF, 30W, 1650W,

3300W)

continuously

adjustable 0-40°C

16A

250x250x390

mm

5.6 kg

PT-05-400 400V~50Hz 5,000

4 (OFF, FAN, 2500W,

5000W)

continuously

adjustable 0-40°C

10A

250x250x390

mm

6.6 kg

PT-09-400 400V~50Hz 9,000

4 (OFF, FAN, 4500W,

9000W)

continuously

adjustable 0-40°C

16A

350x440x480

mm

11.8 kg

To get the most out of your new fan heater, please

read through these instructions and the attached

safety regulations before use. Please also save the

instructions in case you need to remind yourself of

the fan heater’s functions at a later date.

- Housing of steel plate and heat-resistant lacquer

- Supplied complete with cable and plug

(9w may not include cable or plug).

Figure 1. Fan Heater Dials

Function Selector with

three power settings

Thermostat Dial

Special Safety Regulations (cont.)

- Do not place the appliance on moving vehicles or

somewhere it may easily tip over.

- Use the appliance in places with good air

ventilation, do not position it near a wall or corner.

- It is recommended that a separate circuit serving

only this appliance be provided. Keep the power

cable far enough from the hot air outlet.

- If the supply cable is damaged, it must be replaced

by the manufacturer or service agent or a similarly

qualified person in order to avoid a hazard.

- You must not connect other appliances to the

same electrical outlet as the fan heater.

- Do not dispose of electrical appliances as unsorted

municipal waste; use separate collection facilities.

Contact your local government for information

regarding the collection systems available. If

electrical appliances are disposed of in landfills or

dumps, hazardous substances can leak into the

groundwater and get into the food chain, damaging

your health and well-being. When replacing old

appliances with new ones, the retailer is legally

obligated to take back your old appliance for

disposals free of charge.

- If the fan heater is to be permanently installed, the

following instructions must be observed (see figure

2).

Operation

- Position the fan heater so that it stands upright on a

firm surface and at a safe distance from wet

environments and flammable objects.

- Connect the fan heater to the electrical power.

- Set the thermostat dial to the maximum

temperature.

- The fan heater will switch on when the function

selector dial is set to one of the three power

settings.

- Once the room reaches the desired temperature,

turn the thermostat dial back until heating element

turns off. The fan will still continue to run. The

thermostat is now set at your desired temperature,

and the heater will continue to maintain a constant

temperature.

Cleaning and Maintenance

- Before cleaning the appliance, disconnect it from

the outlet and let it cool down.

- The enclosure is easy to get dirty. Wipe it often

with a soft sponge. For very dirty parts, wipe with a

sponge dipped in < 50°C water and mild detergent,

then dry the heater enclosure with a clean cloth.

Be careful not to let the water enter the inside of

the appliance

- In order to protect the enclosure

, don’t splash

water onto the heater, and never use a solvent like

gasoline, isoamyl acetate, toluene, etc. to clean

the heater.

- Clean the coupler, dry and pack it in a plastic bag.

- When you store the heater, let it cool down first

and, keep it dry. Then cover it with a plastic bag,

put it in the packing box and store it in a dry,

ventilated place.

Electric Fan Heater User’s Manual EN Page 3

Figure 2. Installing your Heater

Electric Fan Heater

NEVER LEAVE HEATER

UNATTENDED WHILE BURN-

ING, OR WHILE CONNECTED

TO A POWER SOURCE.

Page is loading ...

ProTemp PT-033-230 User's Manual And Operating Instructions

This manual is also suitable for

ProTemp PT-033-230 User's Manual And Operating Instructions

in other languages

Other documents