Eaton EATS16 Installation and User Manual
- Type
- Installation and User Manual
This manual is also suitable for
Eaton EATS16 is a high-availability automatic transfer switch that provides redundant power for sensitive equipment. It comes with two independent power sources and rapidly switches from one source to another if the primary power fails. The EATS16 is efficient and reliable, offering a clear LCD interface for monitoring power flow, status, parameters, and events. Additionally, the EATS16N model includes a network interface for remote monitoring and configuration via Ethernet.
Eaton EATS16 is a high-availability automatic transfer switch that provides redundant power for sensitive equipment. It comes with two independent power sources and rapidly switches from one source to another if the primary power fails. The EATS16 is efficient and reliable, offering a clear LCD interface for monitoring power flow, status, parameters, and events. Additionally, the EATS16N model includes a network interface for remote monitoring and configuration via Ethernet.
ENGLISH
EATS16
EATS16N
Installation
and user manual
Copyright © 2015 EATON
All rights reserved.
Service and support:
Call your local service representative
EATS16_EN
Page 2
EATS16_EN
SAVE THESE INSTRUCTIONS. This manual contains important instructions
that should be followed during installation and maintenance of the ATS.
The EATON ATS models that are covered in this manual are intended for installation
in an environment within 0°C to 40°C (32°F to 104°F) and free of conductive contaminant.
Certication standards
• Safety:IEC62310-1
• EMC:IEC62310-2
• Performance:IEC62310-3
• CEMark
• Additionalconformances:
- IEC60950-1
- CISPR22ClassB
Important safety notes
• Onlyqualiedpersonnelcanservicethisequipment.
• Followthefollowingprecautionswhenworkingonthisunit.
- Removewatches,rings,orothermetalobjects.
- Usetoolswithinsulatedhandles.
• Examinethepackingcontainer.Notifythecarrierimmediatelyifanydamageispresent.
• Donotdisassembletheunit.
• Do not operate the unit near water or in an area with excessive humidity.
• Keepliquidandforeignobjectsfromgettinginsidetheunit.
• Donotoperatetheunitclosetogasorre.
• Verifywhetherthebranchcircuitbreakerorfuseonservicefeediscorrect.
• Verify line voltage requirements and the supplied line voltage prior to installation.
• Thisunitissuppliedfrommultiplesources,disconnectallsourcesbeforeservicing.
Electrical warnings
• Checkthatpowercords,plugs,andoutletsareingoodcondition.
• RAL equipment:"EquipmentintendedforinstallationinRestrictedAccessLocation".
Warning
• Intendedtobeconnectedtocomputerload.
• Nottobeconnectedtoinductiveloadorwith>3:1crestfactorload.
SAFETY INSTRUCTIONS
Page 3
EATS16_EN
ENGLISH
Contents
1. Introduction ....................................................................................... 4
2. Presentation ...................................................................................... 4
2.1 Weights and dimensions ...............................................................................................4
2.2. Rear panel layout - EATS16 - EATS16N ..........................................................................4
2.3 Control panel ..................................................................................................................4
2.4 LCD description .............................................................................................................5
2.4.1 Power ow ..................................................................................................................... 5
2.4.2 Measures ....................................................................................................................... 6
2.5 ATS settings ...................................................................................................................6
2.6 Warning ..........................................................................................................................8
3. Installation for ATS ........................................................................... 9
3.1 Checking the accessory kit - EATS16 - EATS16N ...........................................................9
3.2 Storage ........................................................................................................................10
3.3 Installation for rack mounting (normal installation) ...................................................... 10
3.4 Installation for rack mounting (2 post installation) ....................................................... 10
3.5 Wall installation ............................................................................................................10
3.5 Instructions ................................................................................................................. 11
4. Power cables connection ............................................................... 12
4.1 Installation diagram ......................................................................................................12
4.2 Input/Output connection EATS16 - EATS16N...............................................................12
5. Communication .............................................................................. 13
5.1 Communication ports: EATS16N .................................................................................13
5.2 Eaton Intelligent Power Software suite .......................................................................14
6. Maintenance ................................................................................... 15
6.1 Troubleshooting ...........................................................................................................15
7. Specications .................................................................................. 16
Page 4
EATS16_EN
1. Introduction
TheEATONAutomaticTransferSwitch(ATS)isahighavailabilityswitchdesignedforprovidingredundant
powerforsensitiveequipment.Itispoweredbytwoindependentpowersourcesandautomaticallymakes
a rapid switch from one source to the other when the power supply used to power its connected load fails.
ThisATSisdesignedtobeefcientandreliable.
UserscanknowEATONATS’spowerow,status,parametersfromtheLCDinterface.Besides,the
EATS16Nunithasanetworkinterfaceforuserstoreadandwriteparameters.Thenetworkinterfacecanbe
implementedviatheEthernetprotocolthroughanRJ45connector.
2. Presentation
2.1 Weights and dimensions
Rack installation
D
H
W
Description Weights
(kg / lb)
Dimensions H x W x D
(mm / inch)
EATS16 3.32/7.31 43 x 438 x 250/1.7x17.24x9.84
EATS16N 3.54/7.8 43 x 438 x 250/1.7x17.24x9.84
2.2. Rear panel layout - EATS16 - EATS16N
2
1
43 3
1
InputSource1:IECC20inlet
2
InputSource2:IECC20inlet
3
Output:8xC1310A
4
Output:1xC1916A
2.3 Control panel
TheATShasthreebuttonsonthecontrolpanelandaLCDdisplay.Itprovidesusefulinformationaboutthe
ATSitself,loadstatus,events,measurementsandsettings.
2
31
4
5
1
LCDpanel
2
Navigation:Scrolldownbutton
3
Navigation:Enterbutton
4
Navigation:Escapebutton
5
TransferTest:ScrolldownandEnter
buttonspressedfor5s
Page 5
EATS16_EN
ENGLISH
2.4 LCD description
1
3
4
2
1
Power flow
3
ATS Settings
2
Measures/Infos
4
Events
2.4.1 Power ow
or
S1isdefinedastheprioritysource(truebydefault)
or
S2isdefinedastheprioritysource(canbeset)
or
S1 not powered
or
S2 not powered
or
S1 powering the load
or
S2 powering the load
or
S1poweredbutnotpoweringtheload
or
S2poweredbutnotpoweringtheload
or
Transfer from S1 to S2
or
Transfer from S2 to S1
or
Transfer from S1 to S2 for Test
or
Transfer from S2 to S1 for Test
2. Presentation
Page 6
EATS16_EN
2. Presentation
2.4.2 Measures
Output current
(default display)
Output voltage
Input voltage : S1
(default display only when S1 voltage is out of tolerance)
Input frequency: S1
(default display only when S1 frequency is out of tolerance)
Input voltage : S2
(default display only when S2 voltage is out of tolerance)
Input frequency: S2
(default display only when S2 frequency is out of tolerance)
S1 and S2 phase shift
(availableonlywhenS1andS2arenotsynchronized)
2.5 ATS settings
OUTPUT: Sets voltage thresholds
-
200V-208V-220V-230 V (default)-240V
ALARM:Silentsalarm
-
ON:normalbeepinwarningorfaultmode,bydefault
OFF:silent.
SENSITIVITY (mainly for LIA UPS):Sets
Sensitivity mode for input mains detection.
-
Std:NormalSensitivity,bydefault
Lo:LowSensitivity,forcompatibilitywithdistorted
waveform.
P SOURCE:Setstheprioritysource Sc.1:PriorityonSource1,bydefault
Sc.2:PriorityonSource2
TRANSFER: Std:noadditionalbreakevenifS1andS2arenot
synchronized,bydefault
Gap:additionalbreakduringtransferifS1andS2are
notsynchronized.
Page 7
EATS16_EN
ENGLISH
2. Presentation
Press Enter to reach settings menu
To cancel the changes
To select value
OUTPUT
ALARM
SENSITIVITY
PRIORITY SOURCE
TRANSFER
Page 8
EATS16_EN
2.6 Warning
ForFault,refertotroubleshootingsection6.1.
Event Example of displays Rootcause
Overload
Loadisovernominalrating
Removesomeoftheequipmentfrom
theATS.TheATScontinuestooperate,
butmayshutdowniftheloadincreases.
The alarm resets when the condition
becomesinactive.
Unsynchronizedsources
OnesourceNandLarereversed
S1ansdS2arefedbydifferentphase
(L1/L2/L3)
S1 and S2 frequency are different
Source 1 or Source 2 power loss
Oneofthesourceismissing,
The ATS power on the load with the
source that is present.
Source 1 or Source 2 voltage out
of tolerance
One of the source voltage is out of
tolerance.
The display shows the voltage measure
of the faulty source.
Source 1 or Source 2 frequency
out of tolerance
One of the source frequency is out of
tolerance.
The display shows the frequency
measure of the faulty source.
Source 1 and Source 2 quality
The sources are outside ranges so that
it generates too many transfers within a
short period of time.
The alarm resets when the condition
becomesinactive.
2. Presentation
Page 9
EATS16_EN
ENGLISH
3. Installation for ATS
3.1 Checking the accessory kit - EATS16 - EATS16N
• VerifythatthefollowingadditionalitemsareincludedwiththeATS:
EATS16
2
3
1
8
7
4
5
6
1
Usermanual
2
Quickstartguide
3
Safety manual printed
4
2xInputcables:C19-C20
5
2xInputcablelockers
6
Plasticstripsforoutputlocking
7
RS232cable
8
Accessoriesforrackinstallation
EATS16N
8
2
3
1
9
7
4
5
6
1
Usermanual
2
Quickstartguide
3
Safety manual printed
4
2xInputcables:C19-C20
5
2xInputcablelockers
6
Plasticstripsforoutputlocking
7
RS232cable
8
DB9/RJ45serialcableforNMCcard
9
Accessoriesforrackinstallation
Page 10
EATS16_EN
3. Installation for ATS
3.2 Storage
• PleasestoretheATSinitsoriginalpackageandinadryplace.
Keepthestoragetemperaturebetween-13to131°F(-25°Cand+55°C).
3.3 Installation for rack mounting (normal installation)
1
3
2
1
3
2
Followsteps1to3formodulemountingontherails.
Accessories for rack installation
• 1xEar(Left)
• 1xEar(Right)
• 4xM4x6atscrewforear
• 4xM6x10cagenutclipforrack4
• 4xM6x12atscrewforrack
• 4xM6washerconicalplateforrack
3.4 Installation for rack mounting (2 post installation)
1
3
2
1
3
2
Followsteps1to3formodulemountingontherails.
Accessories for rack installation
• 1xEar(Left)
• 1xEar(Right)
• 4xM4x6atscrewforear
• 4xM6x10cagenutclipforrack4
• 4xM6x12atscrewforrack
• 4xM6washerconicalplateforrack
Page 11
EATS16_EN
ENGLISH
3.5 Wall installation
Follow steps 1 to 2 for module mounting on the wall.
2
1
2
1
3.6 Instructions
1.ElevatedOperatingAmbient-Ifinstalledinaclosedormulti-unitrackassembly,theoperatingambient
temperatureoftherackenvironmentmaybegreaterthanroomambient.Therefore,consideration
shouldbegiventoinstallingtheequipmentinanenvironmentcompatiblewiththemaximumambient
temperature(Tmax)speciedbythemanufacturer.
2. ReducedAirFlow-Installationoftheequipmentinarackshouldbesuchthattheamountofairow
required for safe operation of the equipment is not compromised.
3. MechanicalLoading-Mountingoftheequipmentintherackshouldbesuchthatahazardousconditionis
not achieved due to uneven mechanical loading.
4. CircuitOverloading-Considerationshouldbegiventotheconnectionoftheequipmenttothesupply
circuit and the effect that overloading of the circuits might have on overcurrent protection and supply
wiring.Appropriateconsiderationofequipmentnameplateratingsshouldbeusedwhenaddressingthis
concern.
5.ReliableEarthing-Reliablegroundingofrack-mountedequipmentshouldbemaintained.Particular
attentionshouldbegiventosupplyconnectionsotherthandirectconnectionstothebranchcircuit(e.g.
use of power strips).
3. Installation for ATS
Page 12
EATS16_EN
4.1 Installation diagram
ATS
Input
ATS
Input
UPS
Input
UPS
Input
UPS
Output
ATS
Output
to the sensitive equiment
UPS
Output
UPS 1
ATS
UPS 2
S1
S2
4.2 Input/Output connection EATS16 - EATS16N
Inputs connections
from UPSs outputs
Ouput connection to equipment
1.ConnectinputpowercablestoUPSsoutputandtoATSinputs(S1isthedefaultprioritysource).
2. Connect ATS output to the equipment.
4. Power cables connection
Page 13
EATS16_EN
ENGLISH
5. Communication
5.1 Communication ports: EATS16N
• RS232 communication port
• Characteristics of the optocouplers communication port
Whenasignalisactivated,thecontactisclosedbetweenthecommon(Pin4)andthepinofthe
correspondingsignalforn.ocontact,andviceversaforn.ccontact.
1
6789
common
2345
Pin assignment Description Contact type Open State Close State
Pin 1 Summary alarm signal n.o Normal Alarm occurred
Pin 2 RX - - -
Pin3 TX - - -
Pin 4 Common - - -
Pin 5 GND - - -
Pin 6 Source 1 OK n.c Source 1 is failure Source1isok
Pin 7 Source 2 OK n.c Source 2 is failure Source2isok
Pin8 Loadonsource1 n.c Source1nottakeload Source1takesload
Pin9 Loadonsource2 n.c Source2nottakeload Source2takesload
n.o:normallyopened
n.c:normallyclosed
2
1.ConnecttheRS232
2
communicationcableto
the serial on the computer.
2. Connect the other end of the
communicationcable
2
to the
RS232
1
communication port
on the ATS.
The ATS can now communicate
with EATON power management
software.
Contact characteristics (optocoupler)
• Voltage:48VDCmax
• Current:25mAmax
• Power:1.2 W
Page 14
EATS16_EN
• Connectivity Cards: EATS16N
ConnectivitycardsallowtheATStocommunicateinavarietyofnetworkingenvironmentsandwith
different types of devices. The Network-MS cardhasSNMPandHTTPcapabilitiesaswellasmonitoring
throughaWebbrowserinterface;connectstoEthernetnetwork.Inaddition,anEnvironmentalMonitoring
Probecanbeattachedtoobtainhumidity,temperature,smokealarm,andsecurityinformation.
Network-MS card
ETHERNET
100M 10M UPS data Reset
Setting/Sensor
5.2 Eaton Intelligent Power Software suite
EatonSoftwaresuiteprovidesup-to-dategraphicsofATSpowerandsystemdataandpowerow.
Italsogivesyouacompleterecordofcriticalpowerevents,anditnotiesyouofimportantATSorpower
information.
5. Communication
Page 15
EATS16_EN
ENGLISH
6. Maintenance
6.1 Troubleshooting
Operation status Possible cause Action
Overload
Power requirement exceeds the
ATS capacity (greater than 105 % of
nominal).
Removesomeoftheequipment
from the ATS.The ATS continues
tooperate,butmayshutdown
if the load increases.The alarm
resetswhentheconditionbecomes
inactive.
Short-circuitfault
Ashort-circuitoccurred. Checkdeviceconnectionor
integrity.
Iferrorpersists,notethealarm
message and the ATS serial
number,andthencontactyour
service representative.
Internalrelayfault
Internalrelayfault,notethatthe
load is no powered.
Note the alarm message and the
ATSserialnumber,andthencontact
your service representative.
Source 1 or Source 2 power
supply fault
Internalpowersupplyofoneofthe
sourceisfaulty;theothersourceis
powering the load.
Note the alarm message and the
ATSserialnumber,andthencontact
your service representative.
EEPROMfault
EEPROMfault,notethattheloadis
still powered.
Note the alarm message and the
ATSserialnumber,andthencontact
your service representative.
Page 16
EATS16_EN
7. Specifications
Table 1. Model list
Model Operating voltage Current rating Operating frequency
EATS16
200/208/220/230/240 Vac 1ɸ
16A 50/60Hz
EATS16N
Table 2. Weights and dimensions
Model Dimensions H x W x D (mm/inch) Weight (kg/lb)
EATS16
43 x 438 x 250 /1.7x17.24x9.84 3.32 /7.31
EATS16N
43 x 438 x 250 /1.7x17.24x9.84 3.54 /7.8
Table 3. Electrical input connections
Model Input connection
EATS16-EATS16N IECC20inlet(2xInputcables:C19-C20provided)
Table 4. Electrical output connections
Model Output connection
EATS16-EATS16N
1xC19
8xC13
Table 5. Environmental and safety
Operating temperature 0°Cto40°C(32°Fto104°F)
Storage temperature -25°Cto55°C/-13°Fto131°F
Relative humidity Storage:0-90%
Operating:20-85%
Operating altitude 2000m meters (6252 ft)
Audible noise 25dBAmax(withoutbuzzer)
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
Eaton EATS16 Installation and User Manual
- Type
- Installation and User Manual
- This manual is also suitable for
Eaton EATS16 is a high-availability automatic transfer switch that provides redundant power for sensitive equipment. It comes with two independent power sources and rapidly switches from one source to another if the primary power fails. The EATS16 is efficient and reliable, offering a clear LCD interface for monitoring power flow, status, parameters, and events. Additionally, the EATS16N model includes a network interface for remote monitoring and configuration via Ethernet.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Eaton ATC-300 Plus Automatic Transfer Switch - found in LMR Plus Electric Fire Pump Controllers Operating instructions
-
-
-
Eaton 9SXEBM36R Installation and User Manual
-
-
Eaton 9PX EBM 180V User guide
-
-
Eaton 9PX10KSP Installation and User Manual
-
-
Other documents
-
POWERSHIELD PSATS3K, User manual
-
CyberPower PDU15SW10ATNET User manual
-
Lapara LA-ON-2K-RACK Datasheet
-
Powerware 1500 VA - 60kVa User manual
-
WTI VMR Series Hardware Guide
-
CyberPower PowerPanel Business 4 User manual
-
-
-
-
