GE ZICS36NALH Specification

Category
Fridges
Type
Specification

This manual is also suitable for

Monogram.
Specification Revised 6/00
R
Listed by
Underwriters
Laboratories
ZICS36NA–GE Monogram 36" Built-In Stainless Steel Bottom Mount
Refrigerator with Automatic Icemaker
Advanced Planning for a Flush or Semi-Flush Enclosure Installation
Monogram built-in refrigerators can be installed flush
with typical 24-3/4” deep cabinetry.
When installed semi-flush, the case trim will conceal
slight gaps around the enclosure. The refrigerator will
project forward approximately 3/4” beyond the front face
of surrounding cabinetry.
Side Panels Requirements:
Side panels are not required whenever the refrigerator is installed
into an enclosure or between pantry and oven cabinets.
Side panels are required whenever the sides of the refrigerator
are exposed.
Side panel sizes vary depending on the type of installation
being made.
To accomplish an attractive installation,
you must:
1. Determine the need for side panels.
2. Determine side panel thickness.
3. Order matching side panels from the cabinet manufacturer. Be
sure to provide the exact dimensions.
Design Information
True Flush Installation
Semi-Flush Installation
True Flush Installation
In a flush installation,
the refrigerator doors
will align evenly with the
front face of adjacent cabinet
doors. The refrigerator blends
into the surrounding cabinetry.
Semi-Flush Installation
These refrigerators
can also be installed
semi-flush into an enclosure
using the minimum cutout
width. The case trim creates a
frame around the opening.
0"
3/4"
For answers to your Monogram,
®
GE Profile Performance Series,
GE Profile
or GE appliance questions, call
GE Answer Center
®
service, 800.626.2000.
Monogram.
Specification Revised 6/00
For answers to your Monogram,
®
GE Profile Performance Series,
GE Profile
or GE appliance questions, call
GE Answer Center
®
service, 800.626.2000.
R
Listed by
Underwriters
Laboratories
1/4" Thick
Side Panels
35-1/2"
Finished Dim.
36"
Roughed-In Dim.
Note: 1/4 thick side panels can be
inserted into the case trim, making
the rough-in the same as the outside
trim width, 36.
ZICS36NAGE Monogram 36" Built-In Stainless Steel Bottom Mount
Refrigerator with Automatic Icemaker
Design Information
Installation Between Base & Wall Cabinets
Cabinet
Refrigerator door
Refrigerator
Cabinet
1/4 Side Panels. Insert end of side panel
into trim.
37"
1/2" Thick
Side Panels
36"
Finished Dim.
Roughed-In Dim.
Note: 1/2 thick side panels shown.
Side panels can be any thickness.
Add side panel thickness to outside
trim width (36)to calculate the
rough-in dimension. The leading
(front) edge must be finished to match
surrounding cabinetry.
Refrigerator
Cabinet
Refrigerator door
Cabinet
1/2 To 3/4 Side Panels. Leading Edge Flush
With Cabinet.
Installation at End of Run
Side panels, 1/2 minimum thickness are required when using
frameless cabinets. The side panel acts as a spacer between
the cabinet and the case trim and prevents interference with
cabinet door swing. The leading (front) edge must be finished
to match surrounding cabinetry.
Frameless Cabinets
Refrigerator
Cabinet
Refrigerator door
1/2 To 3/4 Side Panels. Leading Edge Flush
With Cabinet.
Monogram.
Specification Revised 6/00
For answers to your Monogram,
®
GE Profile Performance Series,
GE Profile
or GE appliance questions, call
GE Answer Center
®
service, 800.626.2000.
R
Listed by
Underwriters
Laboratories
ZICS36NAGE Monogram 36" Built-In Stainless Steel Bottom Mount
Refrigerator with Automatic Icemaker
Dimensions and Specifications (in inches)
4"
24 3/4"
Side View
36" Overall"
35" Case
Front View
26 3/4"
73-1/2"
10 3/4" Max
10" Min
84 1/2" Max*
83 1/2" Min
26"
* 84" Shipping Height. For any other Height Installation
order either ZGCSS36RH (right-hand) or
ZGCSS36LH (left-hand).
7"
Wall View
Electrical
Area
84 1/2" max
83 1/2" min
Finished
Opening
74" From Floor
to
Bottom
of Electrical
5"
5"
3 1/2"
5"
3 1/2"
Water Supply
24 3/4" Total
Depth
*Finished Width
7 1/2"
*36 Min. for a flush installation.
35-1/2 Min. for a semi-flush installation.
Note: Additional cutout width may be required when side panels
are used. Add side panel thickness to the finished cutout to
calculate rough-in width. See installation examples on the
following page.
ZICS36NARH
Handle on the left side, the door swings
left to right.
ZICS36NALH
Handle on the right side, the door swings
right to left.
These refrigerators are equipped with special
hinges that allow the door to swing out and away
from the cabinet. No clearances are required on
the sides.
When the refrigerator is installed in a corner:
A 4 min. clearance on the hinge side will
assure a 90° door opening and access to
all drawers.
A 10 clearance on the hinge side is
required for removal of pans.
To achieve a flush fit the finished cutout
width must be at least 36 wide.
In a semi-flush installation, the finished
cutout must be 35-1/2.
The electrical and water locations must
be located as shown for either type
of installation.
Monogram.
Specification Revised 6/00
R
Listed by
Underwriters
Laboratories
ZICS36NAGE Monogram 36" Built-In Stainless Steel Bottom Mount
Refrigerator with Automatic Icemaker
Dimensions and Specifications (in inches)
84"
23-5/16"
2-5/16"
84"
3-3/4"
24-3/4"
Standard 4 high toekick or trim to fit. Height
may vary depending on application.
Illustration A
1/4 Side Panels
Insert end of side
panel into case trim.
Fasten with Velcro
strips included.
Illustration B
1/2 to 3/4 Side
PanelsLeading
edge of side panel is
flush with cabinet
front. Fasten to the
back wall using a cleat.
Illustration C
1/2 to 3/4 Side
PanelsRecessed
front edge of side
panel. Fasten to
adjacent cabinets.
Standard 4 high toekick or trim to fit. Height
may vary depending on application.
Standard 4 high toekick or trim to fit. Height
may vary depending on application.
Side panels are required whenever the sides of the
refrigerator will be exposed and when installed
between frameless cabinets.
Side panels are not required when the refrigerator is
installed into an enclosure.
Side panel installation will be determined by the
design of the side panel you have previously chosen.
Side panels must be installed plumb.
If you choose to use 1/4 side panels, they should be
inserted into the case trim as illustrated. Fasten the
panels to the refrigerator with velcro strips (provided)
before setting refrigerator in place. See illustration A.
1/2 to 3/4 side panels are normally set into place
and fastened to adjacent cabinetry or the back wall
before rolling the refrigerator into the opening. See
illustrations B and C.
These models are factory set for 84 installation height.
Adjustments to 83-1/2 or 84-1/2 heights can be made by
changing the grille panel.
Order ZGCSS36RH (right hand) or ZGCSS36LH (left hand)
Grille Panel Kit. These kits include 2 grille panels, for 83-1/2
and 84-1/2 installation heights.
For answers to your Monogram,
®
GE Profile Performance Series,
GE Profile
or GE appliance questions, call
GE Answer Center
®
service, 800.626.2000.
Monogram.
Specification Revised 6/00
ZICS36NAGE Monogram 36" Built-In Stainless Steel Bottom Mount
Refrigerator with Automatic Icemaker
Features and Benefits
20.8 Cu.Ft. Capacity (Fresh Food
14.1 Cu.Ft./ Freezer 6.7 Cu.Ft.)
Equipped with Factory Installed
Automatic Icemaker with
Removable Ice Storage Bin
2 Sealed, Adjustable Humidity
Slide-Out Vegetable/Fruit Pans
2 Sealed Slide-Out Snack Pans
Adjustable Spill-Proof Glass Shelves
6 Fresh Food Door Shelves (4
Adjustable, 2 with Gallon Storage)
2 Sealed Dairy Compartments
Egg Bin and Glass-Covered Butter Dish
Wine Holder
Slide-Out Freezer Compartment
with 2-Tier Wire Shelves
Stainless Steel Tubular Handles
Model ZICS36NA - Stainless steel
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

GE ZICS36NALH Specification

Category
Fridges
Type
Specification
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI