Gladiator GAWUXXPTTG Installation guide

Gladiator
Brand
Gladiator
Model
GAWUXXPTTG
Type
Installation guide

Gladiator GAWUXXPTTG is a multifunctional storage system designed to help you organize and store your tools and equipment. With a maximum weight capacity of 100 lbs, it can accommodate a variety of items, such as power tools, hand tools, gardening equipment, and sports gear. It features a sturdy steel construction with a durable powder-coated finish, ensuring longevity and resistance to rust and corrosion. The Project Caddy's versatile design allows for multiple mounting options, including Gladiator® Garageworks GearWall® panels and GearTrack® channels.

Gladiator GAWUXXPTTG is a multifunctional storage system designed to help you organize and store your tools and equipment. With a maximum weight capacity of 100 lbs, it can accommodate a variety of items, such as power tools, hand tools, gardening equipment, and sports gear. It features a sturdy steel construction with a durable powder-coated finish, ensuring longevity and resistance to rust and corrosion. The Project Caddy's versatile design allows for multiple mounting options, including Gladiator® Garageworks GearWall® panels and GearTrack® channels.

PROJECT CADDY
Assembly Instructions
ORGANIZADOR DE
PROYECTOS
Instrucciones de ensamblaje
ORGANISATEUR À
ACCESSOIRES
Instructions d'assemblage
W10176614A
IT'S TIME TO RETHINK THE GARAGE.
®
ES TIEMPO DE VOLVER A PENSAR EN EL GARAGE.™
LE GARAGE REPENSÉ.™
2
INSTALLATION INSTRUCTIONS
Project Caddy Use Requirements
■ Intended to be installed on Gladiator
®
Garageworks GearWall
®
panel or a GearTrack
®
channel.
■ Maximum weight limit is 25 lbs (11.34 kg) for each hook.
■ Maximum weight limit is 100 lbs (45.36 kg) for the project caddy.
Unpack the Project Caddy Parts
Remove the project caddy parts and fasteners, and dispose of/
recycle all packaging materials.
Assemble Project Caddy
Gather the required tools before starting assembly.
Tools Needed:
1. Place the left-hand side piece on a flat surface. Insert the tool
bag hook into the lower channel in the side, as shown.
2. Insert the support rod into the upper channel in the side, as
shown.
3. Insert the tool bag hook and the support rod into the channels in
the right-hand side piece, as shown. Rotate the tool bag hook
downward over the support rod until it locks into place.
4. Insert the threaded studs at the top of each side piece into the
two holes in each side of the project caddy back.
5. Using two acorn nuts (F10) per side, attach the sides to the back.
Completely tighten with a ³⁄₈" nut driver.
6. Attach the project caddy shelf (with the name badge facing up)
by interlocking the shelf tabs with the tabs on the project caddy
back.
NOTE: The tabs on the project caddy back fit underneath the
tabs on the shelf.
F3b F10
F3b Phillips-head screw (2) F10 Acorn nut (10)
■ ³⁄₈" Nut driver ■ Phillips screwdriver
A. Left-hand side
B. Tool bag hook
C. Support rod
A
B
C
A. Right-hand side
A. Project caddy back
B. Acorn nuts (F10)
A. Project caddy shelf
A
B
A
A
A
3
7. Using the two Phillips-head screws (F3b) and two acorn
nuts (F10) fasten the project caddy shelf to the sides.
8. Holding each screw in place with a screwdriver, completely
tighten the acorn nut with the nut driver.
9. Insert the threaded studs on each double-hook end piece into
the two holes in each side piece.
10. Using two acorn nuts (F10) per side, attach the double-hook end
pieces to the sides. Completely tighten with a ³⁄₈" nut driver.
Mount the Project Caddy to the Wall
IMPORTANT: Be sure the GearWall
®
panel or GearTrack
®
channel is
installed with mounting screws in every slot and at every stud
location with a maximum of 24" (60.96 cm) horizontally between
screws.
1. Engage the bracket rims located on the back of the project
caddy into the slots in the GearWall
®
panel or GearTrack
®
channel
by lifting up, pushing toward the wall and lowering the rims into
the slots.
2. Inspect the project caddy from the side to ensure the bracket
rims are fully engaged in the slots as shown.
3. Place the tool bag on the tool bag hook, as shown.
Warranty
For warranty information:
In the U.S.A. call 1-866-342-4089 or visit our website at
www.GladiatorGW.com
In Canada call 1-800-807-6777 or visit our website at
www.gladiatorgarageworks.ca
A. Phillips-head screws (F3b)
B. Acorn nuts (F10)
A. Acorn nuts (F10)
A
A
B
A
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
W10176614A
© 2008 Whirlpool Corporation.
All rights reserved.
Todos los derechos reservados.
Tous droits réservés.
® Registered Trademark/TM Trademark of Whirlpool, U.S.A., Whirlpool Canada LP Licensee in Canada
® Marca registrada/TM Marca de comercio de Whirlpool, U.S.A., usada bajo licencia de Whirlpool Canada LP en Canadá
® Marque déposée/TM Marque de commerce de Whirlpool, U.S.A., emploi sous licence par Whirlpool Canada LP au Canada
6/08
Printed in China
Impreso en China
Imprimé en Chine
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Gladiator GAWUXXPTTG Installation guide

Gladiator
Brand
Gladiator
Model
GAWUXXPTTG
Type
Installation guide

Gladiator GAWUXXPTTG is a multifunctional storage system designed to help you organize and store your tools and equipment. With a maximum weight capacity of 100 lbs, it can accommodate a variety of items, such as power tools, hand tools, gardening equipment, and sports gear. It features a sturdy steel construction with a durable powder-coated finish, ensuring longevity and resistance to rust and corrosion. The Project Caddy's versatile design allows for multiple mounting options, including Gladiator® Garageworks GearWall® panels and GearTrack® channels.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents