Bosch SGI43E15TC/70 Brief description

SGI43E15TC/70
Bosch
Brand
Bosch
Model
SGI43E15TC/70
Type
Brief description

This manual is also suitable for

Summary of instructions for dishwasher
Brief and handy:
everything your dishwasher
needs.
Before using for the first
time, read the installation
and operating instructions!
Select programme Off we go
Switch off the appliance Everything o.k.
Fill with rinse aid
Fill with detergent
Fill with salt
Turn on the tap
Water ready
When the “programme end” display illumi-
nates, switch off the main switch. Turn off
the tap.
Switch on the appliance
Close the door. Press the On/Off switch,
the last selected programme starts automatically.
9000 012 352  
en
Setting the water softening system *
Quickly sorted
Find out the water
hardness at your water
utility company and
enter below
* only before using the
dishwasher for the first
time or if the water hard-
ness changes
Read off the setting
SettingdH fH Clarke mmol/l
and then select a setting
– Hold down programme button B and switch on the main
switch, then release the buttons. The . display flashes and
buttons A and B illuminate (water hardness setting was set
to 2 at the factory).
– Each time button B is depressed, the setting increases by
one (0-3). If buttons A, B and C illuminate, the maximum
water hardness setting has been reached. If the water
hardness setting is now increased again, the lights go out
and the water hardness setting is set to 0.
– Switch off the main switch. The selected setting has been
stored in the appliance.
0
1
2
3
Reset
ABC
22–35
0–6
7–16
17–21
0–1,1
1,2–2,9
3,0–3,7
3,8–6,2
9–20
0–11
12–29
30–37
38–60
0–8
21–26
27–44
Dissolves limescale (not required for set value 0!)
Unscrew
the lid.
Only before using
the dishwasher
for the first time
pour approx. 1 l /
1 1/4 pt water into
the salt opening.
Pour in max.
1.5 kg / 3 lb 5 oz
salt (never deter-
gent!)
Screw on the
lid. Switch on
dishwasher
immediately.
Everything is sparkling clean ... Refill whenever level indicator is light!
Press mark 1,
lift up lid 2.
Pour in
rinse aid.
Close the
lid. CLICK!
Very dirty dishes, a lot of detergent ...
If required, open
the lid (press the
pin).
Warning,
combination
products are not
suitable for all
programmes,
follow manufac-
turer’s instructions.
Pour in
detergent.
Push the lid
shut, press.
PLOP!
Quick, economical or intensive ...
This overview indicates the max. possible number of
programmes. The programmes which correspond to your
appliance can be found on your appliance fascia.
The programme data are values measured in the
laboratory in compliance with Standard EN 50242.
Deviations is practice are possible.
Overview of programmes
150
1,80
21
180
1,30
14
95
0,90
15
50
0,70
10
20
0,10
4
35 50 70 65 40
Duration in minutes
Power consumption in kWh
Water consumption in litres
Intensive
Normal Eco Gentle
Quick Prerinse
140
1,55
18
Maintenance and care
For perfect rinsing results
Filters
Check and,
if required,
clean:
Rotate filter cylinder,
remove filter system
Rinse under
running water
Insert Screw on filter
system.
NOTE MARK!
Spray arms
Remove blockages/
deposits
Pull up lower arm Unscrew upper arm Clean under running
water (if required, use
a toothpick)
Insert lower arm Screw on upper arm
Troubleshooting
Dealing with problems correctly ...
Fault
Possible causes
Residual water in the appliance
Appliance does not run/stops
Utensils are not clean
Sand or gritty residue
on the utensils
Programme not yet finished
No/insufficient water
check whether
Utensils close together/on top of
each other
Insufficient detergent
Unsuitable programme
Spray arms blocked
Filters loose
Filters dirty
Spray arm nozzles blocked
Insufficient water
Turn on the water supply.
Supply fittings unobstructed and
not calcified.
Supply hose kink-free.
Arrange utensils according to
instructions.
Follow manufacturer’s instructions.
Select more intensive programme.
Re-arrange obstacles (e.g. large
spoons).
Clean filters (see above),
attach correctly (MARK).
Clean filters (see above).
Clean spray arms (see above).
See “Appliance does not run”.
Remedial action
Programme does not continue
Programme interrupted
Door is open
Continue the programme (see
Interrupting the programme).
Close the door, switch on the
main switch again.
Wait until programme ends
(programme ends – indicator
illuminates) or terminate programme
(see below).
Fault Possible causes
Remedial action
Plastic parts/utensil
parts discoloured ...
Detergent with lower bleaching
effect
Insufficient detergent
Use detergent containing chlorine
bleach.
Follow manufacturer’s instructions.
Milky deposits on the
utensils (removable)
...
Glasses cloudy/dull ...
Rust on the cutlery ...
Rinse aid dosage too high
(visible streaking)
Rinse aid dosage too low
Water too hard
Glasses not dishwasher-proof
Detergent unsuitable
Cutlery not rust-resistant
Reduce or increase dosage
according to instructions.
Refill with salt/adjust water softening
system.
Use dishwasher-proof glasses.
Use glass-friendly detergents.
Use dishwasher-proof cutlery.
Further information can be found
in the operating instructions ...
Self-help is worthwhile!
Interrupting the programme Cancelling the programme
Arranging utensils
correctly
While the programme is running,
simultaneously press the two
Reset buttons for approx.
3 seconds (RESET).
– Switch off the main switch.
– To continue the programme,
switch on the main switch
again.
Switch off the
appliance.
1 minute after the
programme has
ended, the “pro-
gramme end” dis-
play illuminates.
Arrange dishwasher-proof utensils (without any residual ash, wax, grease,
ink, sticky labels; remove large remnants of jam, dairy products and food)
according to the operating instructions and check that the spray arms can
rotate freely.
  • Page 1 1
  • Page 2 2

Bosch SGI43E15TC/70 Brief description

SGI43E15TC/70
Bosch
Brand
Bosch
Model
SGI43E15TC/70
Type
Brief description
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents