Hotpoint CH60GCIK User guide

Brand: Hotpoint

Model: CH60GCIK

Category: Barbecues & grills

Type: User guide

This manual is also suitable for

This appliance must be installed in accordance with the regulations in force and

only used in a well ventilated space.

Read these instructions before installing or using the appliance and retain

them for future reference.

Use and Installation Instructions

CH60GCIK

CH60GCIS

CH60GCIW

Please phone us on

08448 24 24 24

to activate your

guarantee

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

CONTENTS

PAGE

Introduction 3

For Your Safety 4

Installation Instructions 6

Features 13

Control Panel 14

Automatic Cooking 15

Oven Timer Operation 16

Hotplate 21

Grill 23

Main Oven 25

Main Oven Cooking Chart 27

The “Slow Cook” Setting 29

Top Oven 30

Top Oven Cooking Chart 31

Care and Cleaning 33

Something wrong with your Cooker?/ Disposal 35

Guarantee Information 39

Service Information 40

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

INTRODUCTION

To help you make the best use of your cooker, PLEASE READ THIS BOOKLET CAREFULLY.

Your new cooker is guaranteed and will give lasting service. The guarantee is only applicable if the cooker has

been installed in accordance with the Installation Instructions.

The cooker is designed specifically for domestic use and responsibility will not be accepted for use in any other

installation.

When first using the cooker ensure that the room is well ventilated (e.g. open a window or use an extractor fan)

and that persons who may be sensitive to the odour avoid any fumes. It is suggested that any pets be removed

from the room until the smell has ceased. This odour is due to any temporary finish and also any moisture

absorbed by the insulation.

Our policy is one of continual improvement in design and development, therefore strict accuracy of illustrations

and descriptions cannot be guaranteed.

This appliance conforms with the following European Economic Community directives:This appliance conforms with the following European Economic Community directives:

This appliance conforms with the following European Economic Community directives:

- 2006/95/

EC EC

EC of 12/12/06 (Low Voltage) and subsequent modifications;

- 2004/108/

ECEC

EC of 15/12/04 (Electromagnetic Compatibility) and subsequent modifications;

- 90/396/

EECEEC

EEC of 29/06/90 (Gas) and subsequent modifications (only for models which use gas);

- 93/68/

EECEEC

EEC of 22/07/93 and subsequent modifications.

- 2002/96/

ECEC

- -

- 1275/2008 (Stand-by/ Off mode)

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

FOR YOUR SAFETY

Please read the precautions below before using your cooker.

ALWAYS . . .

ALWAYS make sure you understand the controls before using the cooker.

ALWAYS check that all controls on the cooker are turned off after use.

ALWAYS stand back when opening an oven door to allow heat to disperse.

ALWAYS use dry, good quality oven gloves when removing items from the ovens.

ALWAYS take care when removing items from the top oven/grill when the main oven is on, as the contents may

be hot.

ALWAYS keep the oven and grill doors closed when the cooker is not in use.

ALWAYS place pans centrally over the hotplate burners and position them so that the handles cannot acciden-

tally be caught or knocked or become heated by other burners.

ALWAYSALWAYS

ALWAYS

keep the cooker clean, as a build up of grease or fat from cooking can cause a fire.keep the cooker clean, as a build up of grease or fat from cooking can cause a fire.

keep the cooker clean, as a build up of grease or fat from cooking can cause a fire.

ALWAYS allow the cooker to cool before cleaning.

ALWAYS follow the basic principles of food handling and hygiene to prevent the possibility of bacterial growth.

ALWAYS keep ventilation slots clear of obstructions.

ALWAYS turn off the electricity supply before cleaning or replacing an oven lamp.

ALWAYS refer servicing to CORGI registered appliance service engineers.



The appliance should not be operated by people (including children) with reduced physical, sensory or mental capacities, by

inexperienced individuals or by anyone who is not familiar with the product. These individuals should, at the very least, be

supervised by someone who assumes responsibility for their safety or receive preliminary instructions relating to the

operation of the appliance.



The appliance must be used by adults only for the preparation of food, in accordance with the instructions

outlined in this booklet. Any other use of the appliance (e.g. for heating the room) constitutes improper use and is

dangerous. The manufacturer may not be held liable for any damage resulting from improper, incorrect and

unreasonable use of the appliance.

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

FOR YOUR SAFETY

NEVER . . .

NEVER leave children unsupervised where the cooker is installed as all surfaces will get hot during and after

use.

NEVER allow anyone to sit or stand on any part of the cooker.

NEVER store items that children may attempt to reach above the cooker.

NEVER heat up unopened food containers as pressure can build up causing the container to burst.

NEVER store chemicals, food stuffs, pressurised containers in or on the cooker, or in cabinets immediately

above or next to the cooker.

NEVER fill a deep fat frying pan more than 1/3 full of oil, and never use a lid. DO NOT LEAVE UNATTENDED

WHILE COOKING.

NEVER place flammable or plastic items on or near the hotplate.

NEVER use proprietary spillage collectors on the hotplate.

NEVER use the cooker as a room heater.

NEVER dry clothes or place other times over or near to the hotplate or oven/gril doors.

NEVER wear garments with long flowing sleeves whilst cooking.

NOTE:NOTE:

NOTE: The use of a gas cooking appliance results in the production of heat and moisture in the room in which it

is installed. Always ensure that the kitchen is well ventilated; keep natural ventilation holes open or install a

mechanical ventilation device (mechanical extractor hood).

In particular when using the grill or more than one hotplate burner, open a window if a mechanical ventilation

device is not operating.

! The appliance should not be operated by people (including children) with reduced physical, sensory or mental

capacities, by inexperienced individuals or by anyone who is not familiar with the product. These individuals

should, at the very least, be supervised by someone who assumes responsibility for their safety or receive

preliminary instructions relating to the operation of the appliance.

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

Prior to installation, ensure that the local distribution conditions (nature of the gas and gas pressure) and the

adjustment conditions are compatible. The adjustment conditions for this appliance are stated on the data

badge which is fitted on the back panel.

This appliance is not designed to be connected to a combustion products evacuation device. It must be

installed and connected in accordance with current installation regulations. particular attention should be given

to the relevant requirements regarding ventilation.

MODEL NUMBERS:

Category II2H3+ (GB)

These models are set to burn NATURAL GAS (G20) at 20 mbar but can be converted for use on BUTANE (G30)

at 28-30mbar or PROPANE (G31) at 37mbar with the use of the LPG conversion kit that can be obtained free of

charge, if you contact our Genuine Parts and Accessories department (see Key Contacts, back page).

GAS SAFETY (INSTALLATION & USE) REGULATIONS

It is the law that all gas appliances are installed by competent persons in accordance with the current edition of

the above regulations. It is in your interest and that of safety to ensure compliance with the law.

In the UK, CORGI registered installers work to safe standards of practice. The cooker must also be installed in

accordance with BS 6172. Failure to install the cooker correctly could invalidate the warranty liability claims and

could lead to prosecution.

LOCATION

The cooker may be located in a kitchen, kitchen/diner or a bed-sitting room, but not in a room containing a bath

or shower. The cooker must not be installed in a bed-sitting room of less than 20m

When adjusted for use on Butane (G30) or Propane (G31), the cooker must not be installed in a room or internal

space below ground level, e.g. in a basement.

PROVISION FOR VENTILATION

The room containing the cooker should have an opening window or equivalent and some rooms may require a

permanent vent. For details refer to BS 5440: Part 2 (UK) or I.S. 813 (Republic of Ireland).

The room must have an opening window or equivalent; some rooms may also require a permanent vent. If the

room has a volume between 5 and 10m

, it will require an air vent of 50cm

effective area unless it has a door

which opens directly to outside. If the room has a volume of less than 5m

, it will require an air vent of 100cm

effective area. If there are other fuel burning appliances in the same room, BS 5440: Part 2 should be consulted

to determine air vent requirements.

INSTALLATION INSTRUCTIONS

CH60GCIK

CH60GCIS

CH60GCIW

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

TECHNICAL DATA

Gas connection Rp ½ (½" BSP female)

Pressure test point Front left hotplate injector

Gas rate adjustment None

Aeration adjustment None

Electrical connection Flexible cord fitted with a 3 pin 13 amp plug

230/240V a.c. 50Hz. 13A fuse.

INSTALLATION INSTRUCTIONS









HEAT INPUT INJECTOR HEAT INPUT INJECTOR

HOTPLATE

Front Left and Rear Right

3.05 kW 116 3.0 kW (220g/h) 86

HOTPLATE

Front Right and Rear Left

2.0 kW 103 2.0 kW (145g/h) 70

Grill 3.7 kW 150 3.4 kW (200g/h) 91

Main Oven 2.5 kW 115 2.3 kW (165g/h) 71

Top Oven 1.9 kW 100 1.9 kW (135g/h) 66

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

INSTALLATION INSTRUCTIONS

SPACE FOR FIXING

The cooker can be close fitted below hotplate level. This requires a minimum distance of 600mm between cupboard

units of hotplate height.

When installing next to a tall cupboard, partition or wall, for a minimum distance of 400mm above hotplate level,

allow a side clearance of at least 65mm.

The diagram below illustrates the minimum clearance between the cooker and adjacent walls, cupboards etc.

The wall behind the cooker, 50mm below and 450mm above, and the width of the cooker, must be a non-

combustible material such as ceramic wall tiles.

If the cooker is to be fitted close to a corner on the left hand side, ensure that there is a clearance of at least 50mm

to allow the main oven door to open fully for when removing oven shelves.

65 mm Min

840 mm Min

400 mm Min

600 mm Min

750mm Min

COOKER HOODS

If a cooker hood is to be installed, refer to the cooker hood manufacturers' instructions regarding fixing height.

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

INSTALLATION INSTRUCTIONS

UNPACKING THE COOKER

Unpack the components from inside the grill and oven. Check that the following parts are present:

Grill pan and grid Top oven/grill shelf heat shield

Baking dish Pan supports

Main oven shelves (2) Enamelled burner caps (4)

Top oven/grill shelf (1) Literature

Aluminium burner bodies (4)

LEVELLING

Four skid feet are fitted which can be adjusted up or down to level the cooker.

CONVERSION FOR USE ON BUTANE (G30) OR PROPANE (G31)

Each burner requires the injector to be replaced and bypass screws adjusted or replaced as follows:

1. Remove the loose hotplate burner parts.

2. Using a 7mm socket, replace the hotplate injectors as appropriate (see table on previous page).

3. Re-position the loose burner parts.

4. Remove the enamelled baffle at the front of the grill (2 screws).

5. Remove the screw on the right hand side of the burner and gently slide the burner off the injector.

6. Using a 7mm socket, replace the grill injector as appropriate (see table on previous page).

7. Re-assemble the burner and baffle.

8. Inside the top oven, remove the central screw securing the burner retainer. Slide the retainer to the right slightly

and lift away.

9. Lift the burner assembly and place on the floor of the oven to the right of the burner opening.

10.Using a 7mm socket, replace the oven injector as appropriate (see table on previous page).

11.Re-assemble the oven burner and retainer.

12.Replace the main oven injector following the same procedure as for the top oven.

13.From behind the cooker, remove the screws securing the rear panel and swing the left hand side outwards

(viewed from the rear) to gain access to the main oven flame supervision device.

14.Replace the flame supervision device bypass screw.

15.Re-assemble the rear panel.

16.Carefully pull off the control knobs and timer buttons.

17.Remove the 2 screws securing the underside of the control panel. Slide the control panel to the left slightly to

remove.

18.Remove the 6 screws securing the timer mounting panel. Without completely removing it, manoeuvre the timer

mounting panel to gain access to the thermostat bypass screws.

19.Using a narrow flat bladed screwdriver rotate the bypass screws fully clockwise. The main oven thermostat

bypass screw is located on the body of the thermostat below the spindle, the top oven thermostat bypass

screw is located on the body of the thermostat to the right of the spindle and the hotplate tap bypass screws are

located down the centre of the spindle.

20.Re-assemble the control panel parts.

21.Secure the self-adhesive LPG conversion label over the gas details on the data badge.

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

INSTALLATION INSTRUCTIONS

STABILITY CHAIN

A hole in the gas inlet valve bracket can be used to engage a stability chain.

CONNECTING TO GAS SUPPLY

300

670

Connection to the cooker should be made with an approved appliance flexible connection to BS 669. A length of

0.9 to 1.25m is recommended. The length of hose chosen should be such that when the cooker is in situ, the

hose does not touch the floor.

Those cookers converted to use on LPG should be connected with a hose suitable for LPG and capable of

withstanding a pressure of 50 mbar.

An adaptor backplate should be fitted within the shaded area shown, to allow the cooker to be pushed fully to

the wall and to ensure that the flexible hose is only likely to come into contact with areas at the rear of the

cooker that do not exceed a temperature rise of 70°C.

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

ELECTRICAL CONNECTION

WARNING - THIS APPLIANCE MUST BE EARTHED. CONNECT TO A 230-240V A.C. SUPPLY

ONLY.

Connection to the electricity supply should be made via a properly earthed, readily accessible wall socket

which is adjacent to but not directly above, and not more than 1.25m away from the appliance and capable of

electrical isolation.

The mains lead should be routed such that it cannot touch hot parts of the cooker i.e. the back panel above a

height of 650mm from the floor.

Should this plug not fit the socket outlet in your home it should be cut off and replaced with a suitable plug as

outlined below.

NOTE: The removed plug cannot be used for any other appliance and should therefore be properly disposed of

and not left where children might find it and plug it into a supply socket - with the obvious consequent danger.

IF THE FITTED PLUG IS REMOVED

The flexible mains lead must be correctly connected as below to a three pin plug of not less than 13 amp

capacity. If a B.S. 1363 fused plug is used, it must be fitted with a fuse which is approved to B.S. 1362.

IMPORTANT: The wires in the mains lead fitted to this

appliance are coloured in accordance with the following

code:

GREEN AND YELLOW - EARTH

BLUE - NEUTRAL

BROWN - LIVE

As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings

identifying the terminals in your plug, proceed as follows:

The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with

the letter E or by the earth symbol

or coloured green or green and yellow.

The wire which is coloured blue must be connected to the terminal which is marked with the N or coloured black.

The wire which is coloured brown must be connected to the terminal which is marked with the letter L or

coloured red.

When wiring the plug, ensure that all strands of wire are securely retained in each terminal. Do not forget to

tighten the mains lead clamp on the plug.

As the appliance must be earthed, do not use 2-pin sockets outlets, if you are in doubt, consult a qualified

electrician.

Should the mains lead ever require replacement, it is essential that this operation be carried out by a qualified

electrician and should only be replaced with a flexible cord of the same size i.e. 1.0mm2 cross sectional area

PVC cable, available from our parts department (see Back Cover).

IF A MOULDED PLUG IS FITTED

In the event of replacing a fuse in the plug supplied an ASTA approved fuse to BS1362 must be fitted.

NOTE: The fuse cover must be refitted when changing the fuse. In the event of losing the fuse cover the plug

must not be used until a replacement fuse cover has been obtained and fitted. A new fuse cover can be

obtained from your local Electricity Board. The colour of the correct replacement fuse cover is that of the

coloured marks or inserts in the base of the plug.

Make sure that the cable does not become trapped when pushing the cooker into position.

Green &

Yellow to

Earth

Brown

to Live

Blue to

Neutral

Cord

Clamp

13 Amp

Fuse

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

INSTALLATION INSTRUCTIONS

INSTALLATION AND OPERATIONAL CHECKS

After installation, check for gas soundness. The supply pressure can be checked at the front left hotplate

burner injector.

Fit the hotplate burner bodies and caps, pan supports and shelf shield(s). Referring to the instructions for use

where necessary,

1. Check that the hotplate burners ignite and cross-light to all ports. Check for a steady flame on the low setting.

2. Check that the grill burner ignites and cross-lights to all ports and that the flames remain when the control is

released 3 seconds later, Check for a steady flame on the low setting.

3. Check that with the main oven set to mark 9, the burner ignites and that tha flames remain when the control is

released 3 seconds later. Leave the oven full on with the door closed for 10 minutes, and check that when the

control is turned to mark 1 that the flame reduces.

4. Check that with the top oven set to mark 8, the burner ignites and that the flames remain when the control is

released 3 seconds later. Leave the oven full on with the door closed for 10 minutes, and check that when the

control is turned to mark 1 that the flame reduces.

5. Check the operation of the timer and oven light.

Instruct the user on operation of the cooker.

On those models adjusted for use with LPG, it is normal for the oven and grill burners to burn with yellow tips.

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

Timer

Top oven/grill

rod shelf

Oven light

Oven fan

Door Switch

'Stay Clean' liners

Main oven

rod shelves

Model number &

Serial number label

Inner door glass

Main Oven door

Top Oven door

'Stay Clean' liners

Control panel

Grill pan and

food support

Grill

2000W

3000W

Features

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

Control Panel

Control Knobs for the gas burners

The position of the gas burner controlled by each one of the knobs is shown by a solid ring

•

. To light one of

the burners, hold a lighted match or lighter near the burner and, at the same time, press down and turn the

corresponding knob counter clockwise to the

maximum maximum

maximum

setting. Each burner can be operated at its

maximum, minimum or intermediate power. Shown on the knob are the different symbols for off

•

(the knob is

on this setting when the symbol corresponds with the reference mark on the control panel), for

maximum maximum

maximum

and

minimum minimum

minimum

. To obtain these settings, turn the knob counter clockwise with respect to the off position. To

turn off the burner, turn the knob clockwise until it stops (corresponding again with the

•

symbol).

Electronic Ignition for the Gas Hob*

This device operates when a slight pressure is applied to the button marked with symbol. To light a specific

burner just press the button while pushing the corresponding knob all the way in and turning it counter-

clockwise until it lights.

For immediate lighting, first press the button and then turn the knobFor immediate lighting, first press the button and then turn the knob

For immediate lighting, first press the button and then turn the knob.

! Should the burner flames accidentally go out, turn off the control knob and wait at least 1 minute

before trying to relight.

*Only on certain models

Top Oven / Grill Control

This control switches on the top and bottom heating elements in the top oven.

The temperature in the oven can be set anywhere between 100°C and 220°C.

The temperature of the top oven can be set anywhere between 80°C and 230°C by turning the knob clockwise

from 1 to 8.

To set the grill turn the corresponding knob to

The grill can be operated at

minimum minimum

minimum

.and

maximum maximum

maximum

setting.

Main Oven Control

This control switches on the top and rear heating elements at various times in the main oven, dependent on

which mode has been set.

The temperature of the main oven can be set anywhere between 80°C and 230°C by turning the knob clockwise

from 1 to 9.

‘S’ SLOW Setting*‘S’ SLOW Setting*

‘S’ SLOW Setting*

This is used for slow cooking, keeping food warm and warming plates for short periods.

ELECTRONIC INIECTION BUTTON*

TIMER

MAIN OVEN

CONTROL

TOP OVEN/GRILL

CONTROL

BURNER CONTROLS

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

AUTOMATIC COOKING

The oven timer offers you the following features:

1. Time of Day

2. Automatic Cooking

3. Minute Minder

AUTOMATIC COOKING

The main oven can be controlled automatically.

GUIDANCE ON AUTOMATIC COOKING

1. Select foods which will take the same time to cook.

2. Set the oven timer so that the food has just finished or is just about to finish cooking on your return to the oven.

This will ensure the food has not cooled down and does not require reheating before serving.

3. Food should be as cold as possible when it goes into the oven, ideally straight from the refrigerator. Frozen

meat and poultry should be thawed thoroughly before it is put in the oven.

4. Warm food should never be placed in the oven if there is to be a delay period. Stews prepared by frying the

meat and vegetables should be cooked as soon as possible.

5. Dishes containing left-over cooked poultry or meat, for example Shepherds Pie, should not be cooked automati-

cally if there is to be a delay period.

6. Stews and joints should be cooked by the long slow method, so that the delay period is kept to a minimum.

7. On warm days, to prevent harmful bacterial growth in certain foods (ie poultry, joints, etc) the delayed start

should be kept to a minimum.

8. Wine or beer may ferment and cream may curdle during the delay period, so it is best to add these ingredients

just before serving.

9. Foods which discolour should be protected by coating in fat or tossing in water to which lemon juice has been

added, prior to placing food in the oven.

10.Dishes containing liquid should not be filled too full to prevent boiling over.

11.Food should be well sealed (but not airtight) in a container to prevent the loss of liquid during cooking. Alu-

minium foil gives a good seal.

12.Ensure food is cooked thoroughly before serving.

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

OVEN TIMER OPERATION

000

CLOCKFACE

The timer incorporates a 24 hour clock.

Ensure the correct time of day is always set, before using your cooker.

SYMBOLS

A 'bell' symbol will light up when you select a Minute Minder Period and will remain lit for the

period set.

At the end of the Minute Minder Period, the timer will emit an audible tone and the 'bell'

symbol will disappear.

The 'cookpot' symbol will light up either:-

- When the timer is in manual mode, or

- During the actual Cook Period.

'AUTO' will light up:-

- When the timer is first turned on it will flash. It will go out when a time of day is set or

when the timer is set to manual.

The 'AUTO' symbol will flash at the end of an Auto Cooking programme to indicate that the

programme has finished.

(When the 'AUTO' symbol is flashing, to return the oven to Manual operation, turn the oven controls off,

and press the "Manual" button - The 'AUTO' symbol will go out).

TIMER FUNCTION BUTTONS

Minute Minder Button

Here you can set a time period of up to 23 hours 59 minutes, that will count down. When it reaches zero, the

timer will emit an audible tone.

For Example: If you set 20 minutes, the audible tone will occur 20 minutes later.

AUTO COOKING PROGRAMME

Cook Period Button

Cook Period is the actual length of time for which, the timer will switch the oven(s) on as part of an "Auto

Cooking" programme. (e.g. If you set 2 hours, the food will be cooked for 2 hours).

End Time Button

The time of day at which you want an "Auto Cooking" programme to end.

For Example: If you set a "Cook Period" for 2 hours, and "End Time" of 11:00. The timer will switch the oven(s)

on at 9:00 and turn the oven(s) off at 11:00. You will hear a audible tone at 11:00, to indicate that the Auto

Cooking Programme has finished.

Notes:

- When setting an Auto Cooking programme you will need to set the oven control(s) to the required temperature(s)

when you set the timer.

- If an Auto Cooking programme has been set the oven(s) will only operate during the pre-programmed time.

Manual Button

Needs to be pressed to cancel an Auto Cooking programme and return the oven(s) to Manual operation.

"+" and "-" Buttons

Used to adjust the various timer function settings.

000

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

SETTING THE TIME OF DAY

Step 1 Make sure all oven controls are turned Off.

Step 2 Check the electricity supply to the cooker is turned on.

Step 3 When switched on the display will show 0.00 and the Auto symbol, flashing

intermittently.

Step 4 Press & hold in both the Cook Period & End Time buttons together.

Step 5 With the Cook Period & End Time buttons still held in, press either the "+" or "-"

buttons to set the correct time of day.

Step 6 Release all the buttons simultaneously. THE TIME OF DAY IS NOW SET.

To change the time of day repeat Steps 4, 5 & 6 above.

Note: You cannot adjust the time of day if the timer has been set for an Auto Cooking Programme.

SETTING THE MINUTE MINDER

Step 1 Ensure the time of day is set correctly.

Step 2 Press and hold the Minute Minder button.

Step 3 With the Minute Minder button held in, set the required Minute Minder period using

the "+" and "-" buttons. A 'bell' symbol will light up.

Release all buttons and the timer display will revert back to the time of day. The 'bell' symbol

will remain lit to signify that a Minute Minder period has been set.

At the end of the set time an audible tone will be heard, and the 'bell' symbol will disappear.

Step 4 To cancel the audible tone press the Minute Minder button.

Note 1 When the Minute Minder has been set, the time remaining can be checked at any time by simply pressing

the Minute Minder button.

Note 2 If necessary the Minute Minder can be cancelled before the tone sounds by pressing and holding the

Minute Minder button and then at the same time pressing the "-" button until 0.00 appears in the display

window.

000

OVEN TIMER OPERATION

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

AUTO COOKING PROGRAMMES

There are two Auto Cooking programmes that can be selected using your timer:-

(a) To set the timer to switch the oven(s) On and Off Automatically

(b) To set timer to switch on immediately and OFF automatically after a set cook period.

a) TO SET THE TIMER TO SWITCH THE OVEN(S) ON AND OFF AUTOMATICALLY

This allows you to cook at a specified time for a chosen period before the oven switches off

Automatically.

Step 1 Check that the correct time of day is set, if not follow instructions for setting the time of day.

Step 2 Place food onto the correct shelf position in the oven and close the oven door(s).

Step 3 Press and hold in the Cook Period button. The display will read 0.00 with the

'cookpot' symbol lit.

Step 4 With the Cook Period button still held in, set the required Cook Period using the "+"

and "-" buttons.

Release the buttons and the timer display will revert to the time of day with the 'Auto'

symbol and 'cookpot' symbol lit.

Step 5 Press and hold in the End Time button. The display will read the earliest possible

end time for the Cook Period that you have set above. The 'Auto' symbol and 'cookpot'

symbol will be lit.

Step 6 With the End Time button still held in, use the "+" and "-" buttons to set the 'End

Time' (i.e. The time you require the oven to switch off ).

Release all the buttons and the timer will revert back to the time of day.

The 'Auto' symbol will remain lit to signify that an Auto Cooking Programme has been set.

The 'cookpot' symbol will go out.

Step 7 Turn the oven control(s) to the required temperature, and if necessary select the

appropriate oven function.

At the end of the Automatic Cook Period the Auto Symbol will flash and an intermittent

bleeping sound will be heard.

The audible tone will continue unless cancelled.

The 'Auto' symbol will continue to flash until the timer is returned to Manual operation (see

below).

Step 8 Press the Manual button, the audible tone will be cancelled and the oven(s) will be

returned to Manual.

Step 9 Turn the oven control(s) to the OFF position.

000

4120

6120

4120

6120

OVEN TIMER OPERATION

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

Note 1 When cooking automatically the Cook Period can be checked at any time by simply pressing the

Cook Period button.

Note 2 When cooking automatically the End Time can be checked at any time by simply pressing the

End Time button.

b) TO SET TIMER TO SWITCH ON IMMEDIATELY AND OFF AUTOMATICALLY AFTER A SET

COOK PERIOD

Step 1 Check that the correct time of day is set, if not follow instructions for setting the time of day.

Step 2 Place food onto the correct shelf position in the oven and close the oven door(s).

Step 3 Turn the oven control(s) to the required temperature, and if necessary select the appropriate oven

function.

Step 4 Press & hold in the Cook Period button, the display will read 0.00 and the 'cookpot'

symbol will light up.

With the Cook Period button still held in set the required Cook Period using the "+" and "-"

buttons. Example: 1hr 30 minutes (as shown).

Step 5 Release all buttons.

The timer display will revert to the time of day with the 'Auto' symbol lit & 'cookpot' symbol

remaining lit.

At the end of the Cook Period the 'Auto' symbol will flash and an intermittent audible tone

will be heard. The audible tone will continue until cancelled. The 'Auto' symbol will continue

to flash until the timer is returned to Manual operation (see below).

Step 6 Press the Manual button. The audible tone will be cancelled and the oven(s) will be

returned to Manual.

Step 7 Turn the oven control(s) to the OFF position.

130

4120

6120

NOTE: The Cookpot symbol disappears

6120

OVEN TIMER OPERATION

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

TO CANCEL AN AUTO COOKING PROGRAMME BEFORE THE COOK

PERIOD HAS FINISHED.

Step 1 Turn the oven control to the OFF position.

Step 2 Press the Manual button to return the oven to "Manual" operation. The 'Auto' sym-

bol will go out.

Note 1 When cooking automatically the Cook Period can be checked at any time by simply pressing

the Cook Period button.

OTHER NOTES ON TIMER OPERATION

1. When cooking Automatically the Cook Period can be checked at any time simply by pressing the Cook Period

button.

2. When cooking Automatically the End Time can be checked at any time by simply pressing the End Time button.

3. Having set a Cook Period and End Time an electronic device stores the information. The device within the timer

will switch the oven(s) on and off at the required times.

4. When setting an Auto Cooking Programme and a mistake is made, to clear:-

(a) Press & release the Manual button.

(b) Start the sequence again.

5. If at any time the display shows three flashing zero's 0.00 and 'Auto', it is likely that the electricity supply to the

oven has been interrupted. Reset the timer to the correct time of day.

Food in the oven may, therefore, not

have been cooked, before serving check food is thoroughly heated and completely cooked.

6. To set each function always press and hold the required function button and at the same time press "+" or "-"

buttons.

5100

OVEN TIMER OPERATION

Page is loading ...

Hotpoint CH60GCIK User guide

Brand: Hotpoint

Model: CH60GCIK

Category: Barbecues & grills

Type: User guide

This manual is also suitable for

Download PDF

report

Hotpoint CH60GCIK User guide

This manual is also suitable for

Hotpoint CH60GCIK User guide

Related papers

Other documents