Estate TEDX640PQ0 Owner's manual

Estate
Brand
Estate
Model
TEDX640PQ0
Category
Tumble dryers
Type
Owner's manual

This manual is also suitable for

BYWHIRLPOOLCORPORATION
DRYERUSERINSTRUCTIONS
TableofContents
ASSISTANCE OR SERVICE ............................ 1
DRYER SAFETY ............................................... 1
DRYER USE ...................................................... 3
DRYER CARE ................................................... 5
TROUBLESHOOTING ...................................... 6
WARRANTY ...................................................... 8
Assistance orService
If you need service, first see the "Troubleshooting" section.
Additional help is available by calling our Customer Interaction
Center at 1-800-253-1301 from anywhere in the U.S.A., or write:
Estate Brand Home Appliances
Customer Interaction Center
553 Benson Road
Benton Harbor, MI 49022-2692
Please include a daytime phone number in your correspondence.
To order accessories, call 1-800-442-9991 or visit our website at
www.estateappliances.com.
Keep this book and your sales slip together for future
reference. You must provide proof of purchase or installation
date for in-warranty service.
Write down the following information about your appliance to help
you obtain assistance or service if you ever need it. You will need
to know your complete model number and serial number. You can
find this information on the model and serial number label, located
on your appliance.
Dealer name
Serial number
Address
Phone number
Model number
Purchase date
DRYERSAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injuw, and tell you what can
happen if the instructions are not followed.
8533783
iMPORTANTSAFETYiNSTRUCTiONS
WARNING:Toreducetheriskoffire,electricshock,orinjurytopersonswhenusingthedryer,followbasicprecautions,
includingthefollowing:
m
m
Read all instructions before using the dryer.
Do not place items exposed to cooking oils in your dryer.
items contaminated with cooking oils may contribute to
a chemical reaction that could cause a Ioad to catch fire.
Do not repair or replace any part of the dryer or attempt
any servicing unless specifically recommended in this
Use and Care Guide or in published user-repair instruc-
tions that you understand and have the skills to carry out.
m Do not dry articles that have been previously cleaned in,
washed in, soaked in, or spotted with gasoline, dry-
cleaning solvents, other flammable, or explosive
substances as they give off vapors that could ignite or
explode.
m Do not allow children to ptay on or in the dryer. Close
supervision of children is necessary when the dryer is
used near children.
m Before the dryer is removed from service or discarded,
remove the door to the drying compartment.
m Do not reach into the dryer if the drum is moving.
m Do not install or store the dryer where it will be exposed
to the weather.
m Do not tamper with controls.
m Do not use fabric softeners or products to eliminate static
unless recommended by the manufacturer of the fabric
softener or product.
m Do not use heat to dry articles containing foam rubber or
similarly textured rubber-like materials.
m Clean Iint screen before or after each load.
m Keep area around the exhaust opening and adjacent sur-
rounding areas free from the accumulation of lint, dust,
and dirt.
The interior of the dryer and exhaust vent should be
cleaned periodically by qualified service personnel.
See installation instructions for grounding requirements.
SAVE THESE iNSTRUCTiONS
WARNING: For your safety, the information in this manual must be followed to minimize
the risk of fire or explosion, or to prevent property damage, personal injury, or death.
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
- WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Clear the room, building, or area of all occupants.
• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer, service agency, or
the gas supplier.
Your dryer must be properly installed and vented to achieve
maximum drying efficiency and shorten drying times. Use the
minimum recommended installation clearances found in your
Installation Instructions. See the Installation Instructions for more
information.
Fire Hazard
Use a heavy metal vent.
Do not use a plastic vent.
Do not use a metal foil vent.
Failure to folow these instructions can result in death
or fire.
If the dryer is not properly installed and vented, it will not be
covered under the warranty.
NOTE: Service calls caused by improper venting will be paid for
by the customer, whether it was a paid installation or self-
installed.
1. Do not use plastic vent or metal foil vent. Use 4" (10.2 cm)
metal or flexible metal vent. Do not kink or crush flexible metal
vent. It must be completely extended to allow adequate
exhaust air to flow. Check vent after installation. Refer to your
Installation Instructions for proper length requirements of vent.
2. Use a 4" (10.2 cm) exhaust hood.
3. Use the straightest path possible when routing the vent.
4,
5.
Use clamps to seal all joints. Do not use duct tape, screws or
other fastening devices that extend into the interior of the vent
to secure vent.
Clean exhaust vent periodically, depending on use, but at
least every 2 years, or when installing your dryer in a new
location. When cleaning is complete, be sure to follow the
Installation Instructions supplied with your dryer for final
product check.
DRYERUSE
Load clothes loosely into the dryer. Do not pack the dryer. Allow space for clothes to tumble freely. The following charts show examples
of balanced loads that would allow for proper tumbling.
SUPER CAPACITY DRYERS
Heavy Work Clothes Mixed Load Towels Delicates
4 pair of pants 3 sheets (1 king, 2 twin) 10 bath towels 3 camisoles
4 pair of jeans 4 pillowcases 10 hand towels 1 robe
2 sweatshirts 9 T-shirts 14 washcloths 4 slips
2 sweatpants 9 pair of shorts 1 bath mat 8 undergarments
4 shirts 3 blouses 2 sets of sleepwear
10 handkerchiefs 1 child's outfit
3 shirts
EXTRA LARGE CAPACITY DRYERS
Heavy Work Clothes Mixed Load Towels Delicates
3 pair of pants 3 double sheets 10 bath towels 3 camisoles
4 pair of jeans 4 pillowcases 10 hand towels 1 robe
2 pair of overalls 8 T-shirts 14 washcloths 4 slips
3 shirts 6 pair of shorts 1 bath mat 6 undergarments
2 blouses 2 sets of sleepwear
8 handkerchiefs 1 child's outfit
i!ii!iii, ::: i iiiiiii i/ i!iiiiill! ....
E×piesion Hazard
Keep flammabme materials and vapors, such as
gasoline, away from dryer.
Do not dry anything that has ever had anything
flammabme on it (even after washing)o
Failure to fellow these instructions can result in death,
e×plesien, or fire,
This booklet covers several different models. Your dryer may not
have all of the cycles and features described.
Before using your dryer, wipe the dryer drum with a damp cloth to
remove dust from storing and shipping.
1. Load clothes loosely into the dryer and close the door. Do not
pack the dryer. Allow space for clothes to tumble freely.
2. Turn the Cycle Control knob to the recommended cycle for the
type of load being dried. Use the Energy Preferred Automatic
Setting (*) to dry most heavy to medium-weight fabrics.
3. (OPTIONAL) If your dryer has aTemperature selector, set it to
the recommended setting for the type of fabric being dried.
See "Dryer Cycle Descriptions" (separate sheet) for
temperature suggestions. On some models, temperature is
included in the cycle selections.
4. (OPTIONAL) Your dryer may have a WRINKLE PREVENT TM
feature setting. When you are unable to remove a load from
the dryer as soon as it stops, wrinkles can form. This feature
periodically tumbles, rearranges and fluffs the load without
heat to help avoid wrinkling.
5. (OPTIONAL) Your dryer may have an End of Cycle Signal as
part of the Push To Start button. This signal is helpful when
drying items that should be removed from the dryer as soon
as it stops. Turn the PUSH TO START button to ON or OFR
The signal will sound only if the selector is set to On.
6. If desired, add fabric softener sheet. Follow package
instructions.
7. Press the PUSH TO START button.
Stopping and Restarting
You can stop your dryer anytime during a cycle,
To stop your dryer
Open the dryer door or turn the Cycle Control knob to OFR
NOTE: The Cycle Control knob should point to an Off area when
the dryer is not in use.
To restart your dryer
Close the door. Select a new cycle and temperature (if desired).
Press PUSH TO START.
Fire Hazard
No washer can completely remove oil
Do not dry anything that has ever had any type of oH on
it (including cooking oils).
items containing foam, rubber, or plastic must be dried
on a cmothesmine or by using an Air Cycle.
FaiBure to follow these instructions can resuJt in death
or fire.
Use the Drying Rack to dry items such as sweaters and pillows
without tumbling. The drum turns, but the rack does not move.
If your model does not have a drying rack, you may be able to
purchase one for your model. To find out whether your model allows
drying rack usage and for ordering information, please refer to the
front page of your manual or contact the dealer from whom you
purchased your dryer.
NOTE: The rack must be removed for normal tumbling. Do not
use the automatic cycle with the drying rack.
To use the drying rack
1. Place drying rack in dryer.
Style 1: Your drying rack has front legs. Slide rear pegs into
the dimples on the back wall of the dryer. Lower the front legs
to rest on the dryer opening.
Style 2: Your drying rack does not have front legs. Do not
remove the lint screen. Slide drying rack over the bottom of
the dryer door opening. Push down to secure rack on frame.
2. Put wet items on top of rack, leaving space between items.
Do not allow items to hang over the edge of the rack. Close
the door.
3. Select a timed drying cycle and temperature, or an air cycle.
Items containing foam, rubber, or plastic must be dried on a
clothesline or by using an air cycle. Refer to the following
table.
4. Start the dryer. Reset cycle to complete drying, if needed.
Rack Dry Cycle Temp Time
Washable wool items (block Timed Low 60 min.
to shape, lay flat on rack)
Stuffed toys/pillows (cotton Timed Low 60 min.
or polyester filled)
Stuffed toys/pillows Air N/A 90 min.
Foam rubber filled (no heat)
DRYERCARE
Keep dryer area clear and free from items that would obstruct the
flow of combustion and ventilation air.
Explosion Hazard
Keep flammable materiams and vapors, such as
gasoline, away from dryer.
Place dryer at Beast 18 inches (46 cm) above the floor
for a garage installation.
Failure to do so can resuJt in death, explosion, or fire.
As Needed Cleaning
1. Roll lint off the screen with your fingers.
2. Wet both sides of lint screen with hot water.
3. Wet a nylon brush with hot water and liquid detergent. Scrub
lint screen with the brush to remove residue buildup.
4. Rinse screen with hot water.
5. Thoroughly dry lint screen with a clean towel. Replace screen
in dryer.
1. Apply a nonflammable household cleaner to the stained area
of the drum and rub with a soft cloth until stain is removed.
2. Wipe drum thoroughly with a damp cloth.
3. Tumble a load of clean cloths or towels to dry the drum.
NOTE: Garments which contain unstable dyes, such as denim
blue jeans or brightly colored cotton items, may discolor the dryer
interior. These stains are not harmful to your dryer and will not
stain future loads of clothes. Dry unstable dye items inside-out to
prevent dye transfer.
Clean the lint screen before each load. A screen blocked by lint
can increase drying time.
IMPORTANT:
• Do not run the dryer with the lint screen loose, damaged,
blocked, or missing. Doing so can cause overheating and
damage to both the dryer and fabrics.
• If lint falls off the screen into the dryer during removal, check
the exhaust hood and remove the lint.
Every Load Cleaning
Style 1:
1. The lint screen is located on top of the dryer. Pull the lint
screen toward you. Roll lint off the screen with your fingers.
Do not rinse or wash screen to remove lint. Wet lint is hard to
remove.
2. Push the lint screen firmly back into place.
Style 2:
1. The lint screen is located in the door of the dryer. Pull the lint
screen straight up. Roll lint off the screen with your fingers. Do
not rinse or wash screen to remove lint. Wet lint is hard to
remove.
2. Push the lint screen firmly back into place.
J ili
From Inside the Dryer Cabinet
Lint should be removed every 2 years, or more often, depending
on dryer usage. Cleaning should be done by a qualified person.
From Inside the Exhaust Vent
Lint should be removed every 2 years, or more often, depending
on dryer usage.
1. Unplug dryer or disconnect power.
2. Open the dryer door. Locate the light bulb cover on the back
wall of the dryer. Remove the screw located in the lower right-
hand corner of the cover. Remove the cover.
3. Turn bulb counterclockwise. Replace the bulb with a 10-watt
appliance bulb only. Replace the cover and secure with the
screw.
4. Plug in dryer or reconnect power.
TROUBLESHOOTING
Firsttry the solutions suggested here and possibly avoid the cost of a service call...
Lint on load
• Is the lint screen clogged? Clean lint screen. Check for air
Dryer will not run
• Checkthe following:
Is the power cord plugged in?
Has a fuse blown, or has a circuit breaker tripped? There
may be 2 fuses or circuit breakers for the dryer. Check to
make sure both fuses are intact and tight, or that both circuit
breakers have not tripped.
Was a regular fuse used? Use a time-delay fuse.
Is the dryer door firmly closed?
Was the start button firmly pressed?
Is a cycle selected?
No heat
movement.
• Is the load properly sorted? Sort lint givers (towels, chenille)
from lint takers (corduroy, synthetics). Also sort by color.
• Is the load too big or too heavy? Dry smaller loads so lint
can be carried to the lint screen.
Was the load overdried? Use correct dryer settings for load
type. Overdrying can cause lint-attracting static electricity.
See "Dryer Cycle Descriptions" (separate sheet).
Was paper or tissue left in pockets?
Is pilling being mistaken for lint? Pilling (surface fuzz) is
caused by normal wear and laundering.
Stains on load or color change
• Has a fuse blown, or a circuit breaker tripped? Electric
dryers use 2 household fuses or breakers. The drum may be
turning, but you may not have heat.
• Has an air dry cycle been selected? Select the right cycle
for the types of garments being dried.
• For gas dryers, is the valve open on the supply line?
softener sheets at the beginning of the cycle. Fabric softener
sheets added to a partially-dried load can stain your
garments.
Were items soiled when placed in the dryer? Items should
be clean before being dried.
Were items properly sorted? Sort light colors from dark
colors. Sort colorfast items from noncolorfast items.
Unusual sounds
• Has the dryer had a period of non-use? Ifthe dryer hasn't
been used for a while, there may be a thumping sound during
the first few minutes of operation.
• Is it a gas dryer? The gas valve clicking is a normal operating
sound.
Items shrinking
• Was the dryer overloaded? Dry smaller loads that will tumble
freely.
• Did the load overdry? Check the manufacturer's care label.
Match dryer setting to load type.
Clothes are not drying satisfactorily
• Checkthe following:
Is the lint screen clogged with lint?
Is the exhaust vent or outside exhaust hood clogged with lint,
restricting air movement? Run the dryer for 5-10 minutes.
Hold your hand under the outside exhaust hood to check air
movement. If you do not feel air movement, clean exhaust
system of lint or replace exhaust vent with heavy metal or
flexible metal vent. See your Installation Instructions.
Is the exhaust vent crushed or kinked? Replace with heavy
metal or flexible metal vent. See your Installation Instructions.
Are fabric softener sheets blocking the grille? Use only one
fabric softener sheet, and use it only once.
• Is the dryer located in a room with temperature below
45°F (7°0)? Proper operation of dryer cycles requires
temperatures above 45°F (7°C).
• Was a cold rinse water used? Was the load very wet?
Expect longer drying times with items rinsed in cold water and
with items that hold moisture (cottons).
• Is the load too large and heavy to dry quickly? Separate the
load to tumble freely.
Loads are wrinkled
• Was the load removed from dryer at the end of the cycle?
• Was the dryer overloaded? Dry smaller loads that can
tumble freely.
• Did the load overdry? Check the manufacturer's care label.
Match dryer setting to load type.
Odors
• Have you recently been painting, staining or varnishing in
the area where your dryer is located? Ifso, ventilate the
area. When the odors or fumes are gone from the area, rewash
and dry the clothing.
• If the dryer is electric, is it being used for the first time?
The new electric heating element may have an odor. The odor
will be gone after the first cycle.
Garment damage
• Checkthe following:
Were zippers, snaps, and hooks left open?
Were strings and sashes tied to prevent tangling?
Were care label instructions followed?
Were items damaged before drying?
ESTATE®DRYERWARRANTY
ONE-YEAR FULL WARRANTY
For one year from the date of purchase, when this dryer is operated and maintained according to instructions attached to or furnished
with the product, Whirlpool Corporation will pay for FSP_replacement parts and repair labor costs to correct defects in materials or
workmanship. Service must be provided by a Whirlpool designated service company.
Whirlpool Corporation will not pay for:
1. Service calls to correct the installation of your dryer, including venting. Heavy 4" (10.2 cm) metal exhaust vent must be used. Refer
to the venting section of this manual and your Installation Instructions.
2. Service calls to instruct you how to use your dryer, to replace house fuses or correct house wiring or reset circuit breakers, or to
replace owner accessible light bulbs.
3. Repairs when your dryer is used in other than normal, single-family household use.
4. Damage resulting from accident, alteration, misuse, abuse, fire, floods, acts of God, improper installation (including, but not limited
to, venting with plastic or flexible foil), installation not in accordance with local electrical and plumbing codes, or use of products not
approved by Whirlpool Corporation.
5. Replacement parts or repair labor costs for units operated outside the United States.
6. Pickup and delivery. This product is designed to be repaired in the home.
7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
WHIRLPOOL CORPORATION SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so this exclusion or limitation may not apply
to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
Outside the 50 United States, this warranty does not apply. For details, contact your authorized Estate dealer.
12/03
Replacement Parts
If you need to order replacement parts, we recommend that you
only use FSP_factory specified parts. These parts will fit right and
work right because they are made with the same precision used
to build every new ESTATE®appliance.
To locate FSP replacement parts in your area:
Call the Customer Interaction Center at 1-800-253-1301, or your
nearest designated service center.
For information on how to contact Whirlpool Corporation, please
see front page of this document.
8533783
© 2004 Whirlpool Corporation.
All rights reserved. ® Registered Trademark/TM Trademark of Whirlpool, U.S.A.
2/04
Printed in U.S.A.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Estate TEDX640PQ0 Owner's manual

Estate
Brand
Estate
Model
TEDX640PQ0
Category
Tumble dryers
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents