Matrix MG-A81 Owner's manual

Type
Owner's manual
MAGNUM SERIES
MG-A81
3
PROPER USAGE
1. Do not exceed weight limits of the exercise device.
2. If applicable, set safety stops to appropriate height.
3. If applicable, adjust seat pads, leg pads, foot pads, range of motion
adjustment, or any other type of adjustment mechanisms to a comfortable
start position. Make certain that the adjusting mechanism is fully
engaged to prevent unintentional movement and to avoid injury.
4. Sit on bench (if applicable) and get into appropriate position for exercise.
5. Exercise using no more weight than you can safely lift and control.
6. In a controlled manner, perform exercise.
7. Return weight to its fully-supported start position.
WARRANTY
For North America, please visit www.matrixtness.com for warranty
information along with warranty exclusions and limitations.
PRODUCT SPECIFICATIONS
Max User Weight
Max Training Weight 265 kg / 585 lbs
Product Weight 125 kg / 275.6 lbs
Overall Dimensions
(L x W x H)*
211.5 x 166.8 x 201.0 cm /
83.3” x 65.7” x 79.2”
* Ensure a minimum clearance width of 0.6 meters (24”) for access to and
passage around MATRIX strength equipment. Please note, 0.91 meters (36”)
is the ADA recommended clearance width for individuals in wheelchairs.
MAINTENANCE CHECKLIST
ACTION FREQUENCY
Clean Upholstery
1
Daily
Inspect Cables
2
Daily
Clean Guide Rods Monthly
Inspect Hardware Monthly
Inspect Frame Bi-Annually
Clean Machine As Needed
Clean Grips
1
As Needed
Lubricate Guide Rods
3
As Needed
1
Upholstery & Grips should be cleaned with a mild soap
and water or a non-ammonia based cleaner.
2
Cables should be inspected for cracks or frays and immediately replaced if present.
If excessive slack exists cable should be tightened without lifting the head plate.
3
Guide rods should be lubricated with Teon based lubricant. Apply the
lubricant to a cotton cloth and then apply up and down the guide rods.
TORQUE VALUES
M12 Bolt (Nyloc Nut & Flowdrill) 135 Nm / 100 ft-lbs.
M10 Bolt (Nyloc Nut & Flowdrill) 77 Nm / 57 ft -lbs
M8 Bolts 25 Nm / 18 ft-lbs
M8 Plastic 15 Nm / 11 ft-lbs
M6 Bolts 15 Nm / 11 ft-lbs
Pad Bolts 10 Nm / 7 ft-lbs
ENGLISH
4
IMPORTANT SAFETY INFORMATION
It is the sole responsibility of the purchaser of MATRIX products to instruct all individuals,
whether they are the end user or supervising personnel on proper usage of the equipment.
It is recommended that all users of MATRIX exercise equipment be
informed of the following information prior to its use.
Do not use any equipment in any way other than designed or intended by the manufacturer.
It is imperative that MATRIX equipment be used properly to avoid injury.
INSTALLATION
1. STABLE AND LEVEL SURFACE: MATRIX exercise equipment must
be installed on a stable base and properly leveled.
2. SECURING EQUIPMENT: Manufacturer recommends that all stationary MATRIX
strength equipment be secured to the oor to stabilize equipment and eliminate
rocking or tipping over. This must be performed by a licensed contractor.
3. Under no circumstances should you slide equipment across the oor due to risk of tipping. Use
proper materials handling techniques and equipment recommended by OSHA.
All anchor points must be able to withstand 750 lbs. (3.3 kN) pull-out force.
MAINTENANCE
1. DO NOT use any equipment that is damaged and or has worn or broken parts. Use
only replacement parts supplied by your country’s local MATRIX dealer.
2. MAINTAIN LABELS AND NAMEPLATES: Do not remove labels for any reason. They contain
important information. If unreadable or missing, contact your MATRIX dealer for a replacement.
3. MAINTAIN ALL EQUIPMENT: Preventative maintenance is the key to smooth operating equipment as
well as keeping your liability to a minimum. Equipment needs to be inspected at regular intervals.
4. Ensure that any person(s) making adjustments or performing maintenance
or repair of any kind is qualied to do so. MATRIX dealers will provide service
and maintenance training at our corporate facility upon request.
ADDITIONAL NOTES
This equipment should only be used in supervised areas where access and control is specically
regulated by the owner. It is up to the owner to determine who is allowed access to this training
equipment. The owner should consider a user’s: degree of reliability, age, experience, etc.
This training equipment meets industry standards for stability when used for its intended
purpose in accordance with the instructions provided by the manufacturer.
This equipment is for indoor use only. This training equipment is a Class S product
(designed for use in a commercial environment such as a tness facility). This
training equipment is in compliance with EN ISO 20957-1 and EN 957-2.
WARNING
DEATH OR SERIOUS INJURY CAN OCCUR ON THIS
EQUIPMENT. FOLLOW THESE PRECAUTIONS TO AVOID
INJURY!
1. All warnings and instructions should be read and
proper instruction obtained prior to use. Use this
equipment for its intended purpose ONLY.
2. ALWAYS use a spotter if working out on this
equipment.
3. Do not allow the lifting bar/sled to drop suddenly.
4. Visually ensure lifting bar catches are fully
engaged and seated in the hooks before releasing
the load and exiting the machine.
5. Adjustable stops must be used at all times.
6. ALWAYS set both adjustable stops to the same
height when using this machine.
7. PROPER adjustable stop height depends on the
exercise performed.
Adjust as follows:
• Remove weight from lifting bar/sled.
• For squats, perform the exercise and determine
the lowest comfortable position of the bar/sled
that ensures no spinal compression. For other
exercises, perform the movement and determine
the lowest point of bar travel that is
comfortable without the bar contacting your
body.
• Position both stop catches to stop the bar at this
point. Ensure that they are completely seated
on the stop rods or catch plate.
• FOR SQUATS PERFORMED ON A SMITH PRESS:
NEVER PLACE THE STOPS BELOW THE HEIGHT
INDICATED ON THE EQUIPMENT.
• Load weights onto the lifting bar and carefully
perform the exercise.
8. DO NOT REMOVE THIS LABEL. REPLACE IF DAMAGED
OR ILLEGIBLE.
ENGLISH
WARNING
Plate-loaded / Free Weight
DEATH OR SERIOUS INJURY CAN OCCUR ON THIS
EQUIPMENT. FOLLOW THESE PRECAUTIONS TO AVOID
INJURY!
1. Keep children under the age of 14 away from this
strength training equipment. Teenagers must be
supervised at all times while using this
equipment.
2. This equipment is not intended for use by persons
with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or
instruction concerning use of the equipment by a
person responsible for their safety.
3. All warnings and instructions should be read and
proper instruction obtained prior to use. Use this
equipment for its intended purpose ONLY.
4. Inspect the machine before use. DO NOT use
machine if it appears damaged or inoperable.
5. Do not exceed weight capacity of this equipment.
6. ALWAYS use a spotter if using free weights.
7. Balance the weight applied to this equipment
and/or any barbell. Where applicable, use
retention devices to retain weight discs.
8. Injuries to health may result from incorrect or
excessive training. Cease exercise if you feel faint
or dizzy. Obtain a medical exam before beginning
an exercise program.
9. Keep body, clothing, hair, and fitness accessories
free and clear of all moving parts.
10. Adjustable stops, where provided, must be used
at all times.
11. When adjusting any adjustable mechanism (stop
position, seat position, pad location, range of
motion limiter, pulley carriage, or any other type),
make certain that the adjustable mechanism is fully
engaged prior to use to prevent unintended motion.
12. Manufacturer recommends that this equipment be
secured to the floor to stabilize and eliminate
rocking or tipping over. Use a licensed contractor.
13. If equipment is NOT secured to floor: NEVER allow
resistance straps, ropes or other means to be
attached to this equipment, as this may result in
serious injury. NEVER use this equipment for
support during stretching, as this may result in
serious injury.
14. DO NOT REMOVE THIS LABEL. REPLACE IF
DAMAGED OR ILLEGIBLE.
5
TOOLS REQUIRED FOR ASSEMBLY (not included)
3MM L-Shaped Allen Wrench 10MM L-Shaped Allen Wrench
4MM L-Shaped Allen Wrench 12MM L-Shaped Allen Wrench
5MM L-Shaped Allen Wrench Phillips Screwdriver
6MM L-Shaped Allen Wrench 8MM Open-End Wrench
8MM L-Shaped Allen Wrench 19MM Open-End Wrench
If any items are missing please contact your country’s local MATRIX dealer for assistance.
0 mm 10 20 30 40 50 60 70 80 90 100 110 120 130
UNPACKING
Thank you for purchasing a MATRIX Fitness product. It is inspected before it is
packaged. It is shipped in multiple pieces to facilitate the compact packaging of
the machine. Prior to assembly, conrm all the components by matching them
with the exploded diagrams. Carefully unpack the unit from this box and dispose
of the packing materials in accordance with your local laws. Exercise device must
be assembled by a trained assembly team or be pre-assembled prior to delivery.
CAUTION
To avoid injury to yourself and prevent damage to the frame components,
be sure to have proper assistance removing the frame pieces from this box.
Please be sure to install the equipment on a stable base, and properly level the
machine. Ensure a minimum clearance width of 0.6 meters (24”) for access to
and passage around MATRIX strength equipment. Please note, 0.91 meters (36”)
is the ADA recommended clearance width for individuals in wheelchairs.
TRAINING AREA
1.67 M
(65.7”)
2.12 M
(83.3”)
FREE AREA
0.6 M (2 FT)
WIDE PATH
ENGLISH
6
ENGLISH
A
B
C
C
B
A
B
1
Hardware Qty
A
B
C
Bolt (M10x100L)
Arc Washer (M10)
Nyloc Nut (M10)
4
8
4
2
Hardware Qty
A
B
C
Bolt (M10x100L)
Arc Washer (M10)
Nyloc Nut (M10)
4
8
4
A
B
C
C
B
F
E
C
F
B
E
A
B
C
3
Hardware Qty
A
B
C
D
E
F
Bolt (M10x100L)
Arc Washer (M10)
Nyloc Nut (M10)
Bolt (M10x25L)
Bolt (M10x70L)
Flat Washer (M10)
2
5
4
1
2
4
4
Hardware Qty
A
B
C
D
E
F
Bolt (M10x100L)
Arc Washer (M10)
Nyloc Nut (M10)
Bolt (M10x25L)
Bolt (M10x70L)
Flat Washer (M10)
2
5
4
1
2
4
ASSEMBLY COMPLETE
14
A
B
C
C
B
A
B
1
Apparatuur Aant.
A
B
C
Bout (M10x100L)
Dichtingsring (M10)
Nylon moer (M10)
4
8
4
2
Apparatuur Aant.
A
B
C
Bout (M10x100L)
Dichtingsring (M10)
Nylon moer (M10)
4
8
4
A
B
C
C
B
F
E
C
F
B
E
A
B
C
3
Apparatuur Aant.
A
B
C
D
E
F
Bout (M10x100L)
Dichtingsring (M10)
Nylon moer (M10)
Bout (M10x25L)
Bout (M10x70L)
Vlakke sluitring (M10)
2
5
4
1
2
4
4
Apparatuur Aant.
A
B
C
D
E
F
Bout (M10x100L)
Dichtingsring (M10)
Nylon moer (M10)
Bout (M10x25L)
Bout (M10x70L)
Vlakke sluitring (M10)
2
5
4
1
2
4
MONTAGE VOLTOOID
NEDERLANDS
44
ВАЖНАЯ ИНФОРМАЦИЯ О ТЕХНИКЕ БЕЗОПАСНОСТИ
Покупатель продукции MATRIX несет исключительную ответственность за инструктирование конечных
пользователей
и наблюдающего персонала относительно правильной эксплуатации оборудования.
Перед использованием всем пользователям тренировочного оборудования MATRIX рекомендуется ознакомиться
с представленной далее информацией.
Не используйте оборудование не по назначению или каким-либо иным способом, который не предусмотрен
производителем. Во избежание травм крайне важно использовать оборудование MATRIX надлежащим образом.
УСТАНОВКА
1. УСТОЙЧИВАЯ И РОВНАЯ ПОВЕРХНОСТЬ. Тренировочное оборудование MATRIX должно
быть установлено на устойчивом основании и надлежащим образом выровнено.
2. КРЕПЛЕНИЕ ОБОРУДОВАНИЯ. Производитель рекомендует закрепить все стационарное
оборудование для силовых тренировок MATRIX на полу для устойчивости, предотвращения
качания или опрокидывания. Установку должен выполнять лицензированный подрядчик.
3. Из-за риска опрокидывания ни при каких обстоятельствах не передвигайте оборудование по полу.
Используйте надлежащие методы перемещения материалов и оборудование, рекомендуемые Управлением
по охране труда США.
Все опорные точки должны выдерживать силу выдергивания в 750 фунтов (3,3 кН).
ТЕХНИЧЕСКОЕ ОБСЛУЖИВАНИЕ
1. НЕ используйте поврежденное оборудование или оборудование с изношенными либо сломанными деталями.
Используйте только запасные части, предоставленные местным дилером компании MATRIX в вашей стране.
2. СОХРАНЕНИЕ ЭТИКЕТОК И ФИРМЕННЫХ ТАБЛИЧЕК. Ни при каких обстоятельствах не удаляйте этикетки. На
них указана важная информация. Если информацию сложно прочитать или она отсутствует, обратитесь к
дилеру компании MATRIX для замены.
3. ОБСЛУЖИВАНИЕ ОБОРУДОВАНИЯ. Профилактическое техническое обслуживание является ключевым
фактором бесперебойной работы оборудования, который гарантирует несение вами минимальной степени
ответственности. Оборудование необходимо осматривать через регулярные промежутки времени.
4. Убедитесь в том, что любые лица, осуществляющие регулировку или выполняющие техническое
обслуживания либо ремонт любого рода, имеют соответствующую квалификацию. По запросу дилеры
компании MATRIX проводят тренинги по сервисному и техническому обслуживанию на нашем
корпоративном объекте.
ДОПОЛНИТЕЛЬНЫЕ ПРИМЕЧАНИЯ
Это оборудование следует использовать исключительно в контролируемой зоне, где доступ и эксплуатация
будут осуществляться под наблюдением владельца. Владелец определяет, кому разрешен доступ к этому
тренировочному оборудованию. Владелец должен оценивать степень надежности пользователя, его возраст,
опыт и т. п.
Это тренировочное оборудование отвечает отраслевым стандартам устойчивости при использовании по
назначению в соответствии с инструкциями, предоставленными производителем.
Это оборудование предназначено только для использования в помещении. Это оборудование является изделием
класса S (предназначено для использования в коммерческом помещении, например в фитнес-центре). Данное
тренировочное оборудование соответствует стандартам EN ISO 20957-1 и EN 957-2.
WARNING
DEATH OR SERIOUS INJURY CAN OCCUR ON THIS
EQUIPMENT. FOLLOW THESE PRECAUTIONS TO AVOID
INJURY!
1. All warnings and instructions should be read and
proper instruction obtained prior to use. Use this
equipment for its intended purpose ONLY.
2. ALWAYS use a spotter if working out on this
equipment.
3. Do not allow the lifting bar/sled to drop suddenly.
4. Visually ensure lifting bar catches are fully
engaged and seated in the hooks before releasing
the load and exiting the machine.
5. Adjustable stops must be used at all times.
6. ALWAYS set both adjustable stops to the same
height when using this machine.
7. PROPER adjustable stop height depends on the
exercise performed.
Adjust as follows:
• Remove weight from lifting bar/sled.
• For squats, perform the exercise and determine
the lowest comfortable position of the bar/sled
that ensures no spinal compression. For other
exercises, perform the movement and determine
the lowest point of bar travel that is
comfortable without the bar contacting your
body.
• Position both stop catches to stop the bar at this
point. Ensure that they are completely seated
on the stop rods or catch plate.
• FOR SQUATS PERFORMED ON A SMITH PRESS:
NEVER PLACE THE STOPS BELOW THE HEIGHT
INDICATED ON THE EQUIPMENT.
• Load weights onto the lifting bar and carefully
perform the exercise.
8. DO NOT REMOVE THIS LABEL. REPLACE IF DAMAGED
OR ILLEGIBLE.
WARNING
Plate-loaded / Free Weight
DEATH OR SERIOUS INJURY CAN OCCUR ON THIS
EQUIPMENT. FOLLOW THESE PRECAUTIONS TO AVOID
INJURY!
1. Keep children under the age of 14 away from this
strength training equipment. Teenagers must be
supervised at all times while using this
equipment.
2. This equipment is not intended for use by persons
with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or
instruction concerning use of the equipment by a
person responsible for their safety.
3. All warnings and instructions should be read and
proper instruction obtained prior to use. Use this
equipment for its intended purpose ONLY.
4. Inspect the machine before use. DO NOT use
machine if it appears damaged or inoperable.
5. Do not exceed weight capacity of this equipment.
6. ALWAYS use a spotter if using free weights.
7. Balance the weight applied to this equipment
and/or any barbell. Where applicable, use
retention devices to retain weight discs.
8. Injuries to health may result from incorrect or
excessive training. Cease exercise if you feel faint
or dizzy. Obtain a medical exam before beginning
an exercise program.
9. Keep body, clothing, hair, and fitness accessories
free and clear of all moving parts.
10. Adjustable stops, where provided, must be used
at all times.
11. When adjusting any adjustable mechanism (stop
position, seat position, pad location, range of
motion limiter, pulley carriage, or any other type),
make certain that the adjustable mechanism is fully
engaged prior to use to prevent unintended motion.
12. Manufacturer recommends that this equipment be
secured to the floor to stabilize and eliminate
rocking or tipping over. Use a licensed contractor.
13. If equipment is NOT secured to floor: NEVER allow
resistance straps, ropes or other means to be
attached to this equipment, as this may result in
serious injury. NEVER use this equipment for
support during stretching, as this may result in
serious injury.
14. DO NOT REMOVE THIS LABEL. REPLACE IF
DAMAGED OR ILLEGIBLE.
РУССКИЙ
MG-A81
© 2019 Johnson Health Tech
Rev 1.0 B
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47

Matrix MG-A81 Owner's manual

Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI