Comnet FVT10D1EM User manual
- Category
- Network switches
- Type
- User manual
This manual is also suitable for
Comnet FVT10D1EM is a compact and versatile fiber optic video transmission system that enables the extension of video signals over long distances using optical fiber cables. It supports the transmission of one channel of 10-bit digitally encoded video along with one bidirectional data channel and one full-duplex 10/100 Mbps Fast Ethernet port. The device features automatic reverse data transmission, and its data channel can be configured for various protocols such as RS232, RS422, or RS485, making it suitable for a wide range of applications.
Comnet FVT10D1EM is a compact and versatile fiber optic video transmission system that enables the extension of video signals over long distances using optical fiber cables. It supports the transmission of one channel of 10-bit digitally encoded video along with one bidirectional data channel and one full-duplex 10/100 Mbps Fast Ethernet port. The device features automatic reverse data transmission, and its data channel can be configured for various protocols such as RS232, RS422, or RS485, making it suitable for a wide range of applications.
INS_FVT/FVR10D1E_REV–
12/28/09
PAGE 1
INSTALLATION AND OPERATION MANUAL
FVT/FVR10D1E(M,S)[M]
10-BIT DIGITALLY ENCODED VIDEO TRANSMITTER
WITH 1 BI-DIRECTIONAL DATA CHANNEL
AND 10/100MB ETHERNET
The FVT/FVR10D1E is a single (1) channel ten (10) bit video transmission
system along with one channel of bi-directional data and one full duplex
10/100 Mbps Fast Ethernet port.
The data channel is configured using a two position switch to operate as RS232,
RS422 or RS485, either two (2) wire or four (4) wire. See Figure 7 for details.
The video channel also supports “up-the-coax” reverse data that is enabled
automatically.
The Ethernet uses a RJ45 data connector. The data input/output also uses
an RJ45 data connector and a “breakout box” to facilitate attachment of the
external wires. The breakout box and connecting cable are supplied with the
FVT/FVR10D1E module.
The FVT/FVR10D1E may be directly plugged into the ComNet Rack (Part #C1)
or operated as a standalone module powered by the PS-9VDC power supply
also provided with the module.
The FVT/FVR10D1E requires one optical fiber and may be supplied in a
multimode (M) or singlemode (S) version.
See Figures 1 – 11 for complete installation details.
INS_FVT/FVR10D1E_REV–
12/28/09
PAGE 2
NOTE: Remove Electrical Connector for Rack Mount Units
FIGURE 2 – FVT10D1E TRANSMITTER
FIGURE 1 – FVT/FVR10D1E TRANSMITTER AND RECEIVER
FIGURE 3 – FVR10D1E RECEIVER
INSTALLATION AND OPERATION MANUAL FVT/FVR10D1E
REAR PANEL REAR PANELFRONT PANEL FRONT PANEL
TECH SUPPORT: 1.888.678.9427
MULTIMODE OR SINGLE MODE
OPTICAL FIBER
BLACK
BLACK WITH WHITE STRIPE
Power Supply:
Surface Mount: 8–15 VDC @ 350mA
Rack Mount: From Rack
INS_FVT/FVR10D1E_REV–
12/28/09
PAGE 3
FIGURE 5 – FVT10D1E TRANSMITTER
FIGURE 4 – FVT10D1EM MINI TRANSMITTER
INSTALLATION AND OPERATION MANUAL FVT/FVR10D1E
REAR PANELFRONT PANEL
TECH SUPPORT: 1.888.678.9427
MULTIMODE OR SINGLE MODE
OPTICAL FIBER
BLACK
BLACK WITH WHITE STRIPE
Power Supply:
Surface Mount: 8–15 VDC @ 350mA
DIN+
DIN–
TERM
DOUT+
DOUT–
BIAS
GND
LEDs: POWER FIBER VIDEO DATA
GND
+Vin
ETHERNET
OPTICAL
VIDEO IN
INS_FVT/FVR10D1E_REV–
12/28/09
PAGE 4
FIGURE 6 – RJ45 BREAK-OUT
Factory Supplied
INSTALLATION AND OPERATION MANUAL FVT/FVR10D1E
TECH SUPPORT: 1.888.678.9427
INS_FVT/FVR10D1E_REV–
12/28/09
PAGE 5
FIGURE 7 – SWITCH POSITIONS
The mode for each data channel is configured using a set of two switches on the front panel of the unit.
The mode for the data on the FVT10D1E(M,S)M small size unit is set by the receiving unit it is connected to.
FIGURE 8 – SWITCH SETTINGS
RS232
1 NC
2 IN (-)
3 Ground
4 NC
5 OUT (-)
6 NC
7 NC
8 NC
RS485 (2W)
& SENSORNET
1 IN/OUT (+) A
2 IN/OUT (-) B
3 Ground
4 NC
5 NC
6 NC
7 NC
8 NC
RS422, RS485
(4W), Manchester
& Bi-Phase
1 IN (+)
2 IN (-)
3 Ground
4 OUT (+)
5 OUT (-)
6 NC
7 NC
8 NC
NC = No Connection
TECH SUPPORT: 1.888.678.9427
INSTALLATION AND OPERATION MANUAL FVT/FVR10D1E
INS_FVT/FVR10D1E_REV–
12/28/09
PAGE 6
FIGURE 9 – DATA CONNECTIONS
See Page 5 for Switch Settings
RS-232*
Customer
Equipment
FVT10D1E
Customer
Equipment
FVR10D1E
RS-422*
Bi-phase or
Manchester*
DOUT(+)
DOUT(-)
DIN(+)
DIN(-)
Data In (+)
Data In (-)
Data Out (+)
Data Out (-)
2-Wire
RS-485,
Sensornet*
DIN(+)
DIN(-)
DIN(+)
DIN(-)
Data (A)
Data (B)
Data (A)
Data (B)
Data Transmit
Data Receive
Signal Ground
DIN(-)
DOUT(-)
GND
DOUT(-)
DIN(-)
GND
Data Receive
Data Transmit
Signal Ground
4-Wire
RS-485*
DIN(+)
DIN(-)
DOUT(+)
DOUT(-)
DOUT(+)
DOUT(-)
DIN(+)
DIN(-)
Data Out (A)
Data Out (B)
Data In (A)
Data In (B)
Data In (A)
Data In (B)
Data Out (A)
Data Out (B)
DIN(+)
DIN(-)
DOUT(+)
DOUT(-)
DOUT(+)
DOUT(-)
DIN(+)
DIN(-)
Data Out (+)
Data Out (-)
Data In (+)
Data In (-)
Data In (+)
Data In (-)
Data Out (+)
Data Out (-)
TECH SUPPORT: 1.888.678.9427
INSTALLATION AND OPERATION MANUAL FVT/FVR10D1E
INS_FVT/FVR10D1E_REV–
12/28/09
PAGE 7
FIGURE 11 – LED INDICATORS
FIGURE 10 – ETHERNET CONFIGURATION
FIBER VIDEO 10/100 LINK DATA POWER
GREEN Communication link has An active video signal is Ethernet link has been An active data signal is Unit powered up
been established over present on the BNC established at the present on the input pins
optical fiber connector. RJ45 connector. of the data connector.
RED Communication link has No video signal – – –
not been established.
OFF Not powered up correctly – – No data signal Unit powered down
Ethernet IEEE 802.3
Network Element
Ethernet IEEE 802.3
Network Element
FVT10D1E FVR10D1ECAT5E/6 with
RJ45 Connections
CAT5E/6 with
RJ45 Connections
Optical Fiber
Ethernet IEEE 802.3 Network Element determined by user.
INS_FVT/FVR10D1E_REV–
12/28/09
PAGE 8
© 2010 Communications Networks Corporation. All Rights Reserved. “ComNet” and the “ComNet Logo” are registered trademarks of Communication Networks, LLC.
3 CORPORATE DRIVE | DANBURY, CT 06810 | USA
T: 203.796.5300 | F: 203.796.5303 | TECH SUPPORT: 1.888.678.9427 | INFO@COMNET.NET
8 TURNBERRY PARK ROAD | GILDERSOME | MORLEY | LEEDS, UK LS27 7LE
T: +44 (0)113 307 6400 | F: +44 (0)113 253 7462 | INFO-EUROPE@COMNET.NET
INSTALLATION CONSIDERATIONS
This fiber-optic link is supplied as a Standalone/Rack module. Units
should be installed in dry locations protected from extremes of
temperature and humidity.
C1-US, C1-EU, C1-AU OR C1-CH CARD CAGE RACKS
CAUTION: Although the units are hot-swappable and may be installed
without turning power off to the rack, ComNet recommends that
the power supply be turned off and that the rack power supply
is disconnected from any power source. Note: Remove electrical
connector before installing in card cage rack.
1. Make sure that the card is oriented right side up, and slide it into
the card guides in the rack until the edge connector at the back
of the card seats in the corresponding slot in the rack’s connector
panel. Seating may require thumb pressure on the top and bottom
of the card’s front panel.
CAUTION: Take care not to press on any of the LEDs.
2. Tighten the two thumb screws on the card until the front panel of
the card is seated against the front of the rack.
WARNING: Unit is to be used with a Listed Class 2 or LPS power supply rated
9-12 VDC @ 1A.
IMPORTANT SAFEGUARDS:
A) Elevated Operating Ambient - If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may
be greater than room ambient. Therefore, consideration should be given to
installing the equipment in an environment compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
B) Reduced Air Flow - Installation of the equipment in a rack should be such
that the amount of air flow required for safe operation of the equipment is
not compromised.
MECHANICAL INSTALLATION INSTRUCTIONS
FIGURE A
Dimensions are for a standard ComNet™ one slot module
.156 [3.96 mm]
.313 [7.95 mm]
FVT/FVR10DIE(M,S)[M] Part Ordering Options:
(M,S): Fiber Type
M: Multimode
S: Singlemode
[M]: Mini Enclosure (optional)
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Comnet FVT10D1EM User manual
- Category
- Network switches
- Type
- User manual
- This manual is also suitable for
Comnet FVT10D1EM is a compact and versatile fiber optic video transmission system that enables the extension of video signals over long distances using optical fiber cables. It supports the transmission of one channel of 10-bit digitally encoded video along with one bidirectional data channel and one full-duplex 10/100 Mbps Fast Ethernet port. The device features automatic reverse data transmission, and its data channel can be configured for various protocols such as RS232, RS422, or RS485, making it suitable for a wide range of applications.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Comnet FVT/FVR10D1A2C1 Series User manual
-
-
-
-
-
Comnet FVT/FVR4014 Series User manual
-
-
-
Comnet FVT/FVR8018 Series User manual
-
Other documents
-
Milan Technology RS485-CF-0x User manual
-
Dante DFC3301iRCZM2S Operating instructions
-
GE Phoenix A8950CC User manual
-
Pelco FR85081 User manual
-
-
-
-
-
-
oxic XFO1013TS User manual
