Ransomes 88010, 88042 Owner's manual
- Category
- Lawnmowers
- Type
- Owner's manual
This manual is also suitable for
WARNING:If incorrectly used, this machine can cause severe injury. Those who
use and maintain this machine should be trained in its proper use, warned of its
dangers and should read the entire manual before attempting to set up, operate,
adjust or service the machine.
GB
Safety & Operation
Manual
When Performance Matters.
™
WARNING
If incorrectly used, this machine can cause severe injury. Those who use
and maintain this machine should be trained in its proper use, warned of its
dangers, and should read the entire manual before attempting to set up,
operate, adjust, or service the machine.
Groom Master II
™
Sand Trap Rake / Groomer
with ROPS
88010, Briggs & Stratton
®
Vanguard, 3WD
88042, Kubota
®
D722-E3B, 3WD
4201264-Rev A
1 CONTENTS
2
Proposition 65 Warning
Engine exhaust from this product
contains chemicals known to the State
of California to cause cancer, birth
defects, and other reproductive harm
© COPYRIGHT 2010, Jacobsen, A Textron Company.
“All rights reserved, including the right to reproduce this book or portions thereof in any form”.
All information in this publication is based on information available at time of approval for printing. Jacobsen reserves the
right to make changes at any time without notice and without incurring any obligation.
This manual contains Safety and Operating instructions for
your new Jacobsen machine. A Parts & Maintenance
Manual has also been included that contains adjustment,
maintenance, troubleshooting instructions, and parts list.
Both manuals should be stored in the literature pouch
behind the seat for reference during operation.
Before you operate your machine, you and each operator
you employ, should read both manuals carefully in their
entirety. By following the safety, operating, and maintenance
instructions, you will prolong the life of your mower and
maintain its maximum efficiency.
If additional information is needed, contact your Jacobsen
Dealer.
The mower serial plate is located on the seat pan, to the left
of the seat. Jacobsen recommends you record these
numbers below for easy reference.
®
P.O. BOX 7708,
CHARLOTTE,
NC 28241, USA
A T extron Compa n y
kg kg kg kW
Jacobsen.com
1-800-848-1636 (US)
PRODUCT OF U.S.A.
FORWORD
1 CONTENTS
1CONTENTS
2SAFETY
2.1 Operating Safety.................................................. 3
2.2 Important Safety Notes ........................................ 4
3DECALS
3.1 Decals.................................................................. 5
4 INITIAL INSPECTION
4.1 General ................................................................ 8
4.2 Initial Inspection ................................................... 8
5 CONTROLS
5.1 Icons .................................................................... 9
5.2 Control Descriptions .......................................... 11
5.3 Operator Alerts .................................................. 12
6 OPERATION
6.1 Daily Inspection ................................................. 13
6.2 Interlock System ................................................ 13
6.3 Operating Procedures ....................................... 14
6.4 Starting .............................................................. 15
6.5 Stopping / Parking ............................................. 15
6.6 To Drive / Transport ........................................... 16
6.7 Hillside Operation .............................................. 16
6.8 Attachments ....................................................... 18
6.9 Towing / Trailering ............................................. 18
6.11 Daily Maintenance ............................................. 19
6.12 Long Term Storage ............................................ 20
7NOTES
LITHO IN U.S.A. 4-2010
SAFETY 2
3
2 SAFETY
2.1 OPERATING SAFETY ______________________________________________________
1. Safety is dependent upon the awareness, concern,
and prudence of those who operate or service the
equipment. Never allow minors to operate any
equipment.
2. It is your responsibility to read this manual and all
publications associated with this equipment (Safety &
Operation Manual, Engine Manual, and attachments/
accessories instruction sheets). If the operator
cannot read English it is the owner’s responsibility to
explain the material contained in this manual to them.
3. Learn the proper use of the machine, the location
and purpose of all the controls and gauges before
you operate the equipment. Working with unfamiliar
equipment can lead to accidents.
4. Never allow anyone to operate or service the
machine or its attachments without proper training
and instructions, or while under the influence of
alcohol or drugs.
5. Wear all the necessary protective clothing and
personal safety devices to protect your head, eyes,
ears, hands, and feet. Operate the machine only in
daylight or in good artificial light.
6. Evaluate the terrain to determine what accessories
and attachments are needed to properly and safely
perform the job. Only use accessories and
attachments approved by Jacobsen.
7. Stay alert for holes in the terrain and other hidden
hazards.
8. Inspect the area where the equipment will be used.
Pick up all the debris you can find before operating.
Beware of overhead obstructions (low tree limbs,
electrical wires, etc.) and also underground obstacles
(sprinklers, pipes, tree roots, etc.). Enter a new area
cautiously. Stay alert for hidden hazards.
9. Never direct discharge of material toward bystanders,
nor allow anyone near the machine while in
operation. The owner/operator can prevent and is
responsible for injuries inflicted to themselves, to
bystanders, and damage to property.
10. Do not carry passengers. Keep bystanders and pets
a safe distance away.
11. Never operate equipment that is not in perfect
working order or is without decals, guards, shields,
discharge deflectors, or other protective devices
securely fastened in place.
12. Never disconnect or bypass any switch.
13. Do not change the engine governor setting or
overspeed the engine.
14. Carbon monoxide in the exhaust fumes can be fatal
when inhaled. Never operate the engine without
proper ventilation or in an enclosed area.
15. Fuel is highly flammable; handle with care.
16. Keep the engine clean. Allow the engine to cool
before storing and always remove the ignition key.
17. Disengage all drives and engage parking brake
before starting the engine (motor). Start the engine
only when sitting in operator’s seat, never while
standing beside the unit.
18. Equipment must comply with the latest federal, state,
and local requirements when driven or transported on
public roads. Watch out for traffic when crossing or
operating on or near roads.
19. Local regulations may restrict the age of the operator.
20. Never use your hands to search for oil leaks.
Hydraulic fluid under pressure can penetrate the skin
and cause serious injury.
21. Operate the machine up and down the face of slopes
(vertically), not across the face (horizontally).
22. To prevent tipping or loss of control, do not start or
stop suddenly on slopes. Reduce speed when
making sharp turns. Use caution when changing
directions.
23. Always use the seat belt when operating groomer
equipped with a Roll Over Protective Structure
(ROPS).
Never use a seat belt when operating groomer
without a ROPS.
24. Always disconnect battery cables from battery before
performing any welding operation on the groomer.
This machine is to be operated and maintained as specified in this manual. It is intended for professional use
and is equipped with attachments designed to move, smooth and loosen sandy materials on golf courses and
sports fields. It is not intended for use with hard compacted soil or gravel.
WARNING
EQUIPMENT OPERATED IMPROPERLY OR BY UNTRAINED PERSONNEL CAN BE DANGEROUS.
Familiarize yourself with the location and proper use of all controls. Inexperienced operators should receive
instruction from someone familiar with the equipment before being allowed to operate the machine.
!
2 SAFETY
4
2.2 IMPORTANT SAFETY NOTES _______________________________________________
This safety alert symbol is used to alert you to potential hazards.
DANGER - Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury.
WARNING - Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious
injury.
CAUTION - Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury
and property damage. It may also be used to alert against unsafe practices.
NOTICE - Indicates a potentially hazardous situation which, if not avoided, MAY result in property damage. It may
also be used to alert against unsafe practices.
For pictorial clarity, some illustrations in this manual may show shields, guards, or plates open or removed. Under no
circumstances should this equipment be operated without these devices securely fastened in place.
By following all instructions in this manual, you will prolong the life of your machine and maintain its maximum
efficiency. Adjustments and maintenance should always be performed by a qualified technician.
If additional information or service is needed, contact your Authorized Jacobsen Dealer who is kept informed of the
latest methods to service this equipment and can provide prompt and efficient service.
WARNING
The Interlock System on this groomer prevents the groomer from starting
unless the parking brake is engaged and traction pedal is in Neutral. The
system will stop the engine if the operator leaves the seat without engaging
the parking brake.
NEVER operate groomer unless the Interlock System is working.
!
WARNING
1. Before leaving the operator’s position for any reason:
a. Return traction pedal to Neutral.
b. Disengage all drives.
c. Lower all implements to the ground.
d. Engage parking brake.
e. Stop engine and remove the ignition key.
2. Keep hands, feet, and clothing away from moving parts. Wait for all
movement to stop before you clean, adjust or service the machine.
3. Keep the area of operation clear of all bystanders and pets.
4. Never carry passengers, unless a seat is provided for them.
!
DECALS 3
5
3 DECALS
3.1 DECALS _________________________________________________________________
Familiarize yourself with the following decals. They are critical to the safe operation of the
machine. REPLACE DAMAGED DECALS IMMEDIATELY.
4181865
4181864
• Read operator's manual. Do not allow untrained
operators to use machine.
• Keep shields in place and hardware securely
fastened.
• Keep hands, feet, and clothing away from moving
parts.
• Before you clean, adjust, or repair this equipment,
disengage all drives, engage parking brake, and stop
engine.
• Never carry passengers.
• Keep bystanders away.
• Do not use on slopes greater than 15°.
Danger
To avoid injury when working with battery:
1. Always connect the black (-) ground last and remove it
first.
2. Keep sparks and flames away, and avoid contact with
acid.
To avoid injury when jumping battery:
1. Connect positive (+) terminal to positive (+) terminal.
2. Connect negative (-) terminal on good battery to frame
of vehicle that has dead battery.
3 DECALS
6
Familiarize yourself with the following decals. They are critical to the safe operation of the
machine. REPLACE DAMAGED DECALS IMMEDIATELY.
700877
4199140
4164281
4181860
WARNING
To prevent burns, do not touch muffler or muffler
shield. Temperatures may exceed 150° F (66° C).
WARNING
Pinch Point
Keep hands away.
WARNING
Failure to read and obey warnings and operating
instructions may result in serious or fatal injury to
you or others and may also result in equipment
and/or property damage. Read Safety &
Operation Manual before operating groomer.
Avoid sharp turns, quick stops, and sudden
direction changes, especially on hills. Go up and
down slopes, not accross. (Located on Oil Tank
Cover)
To prevent serious injury, never disconnect or
tamper with the seat switch. Read Manual for
more information. (Located under Control Panel)
Do not use this machine on slopes greater than
15°. Keep bystanders away. Read Safety &
Operation Manual for more information. (Located
on Steering Tower)
DECALS 3
7
4181863
838368
4135931
3008577
3002308
838363
3008576
838364
WARNING (Gas Units Only)
Stop engine before engaging or disengaging belt ider. Engaging
idler while engine is running may cause vehicle to move in either
forward or reverse direction without warning and may result in
personal injury, death, equipment damage, and/or property
damage. See manual for operating instructions.
Hydraulic Oil Tank
Raise
Rake
Lower
Raise
Blade
Lower
Raise
Scarifier
Lower
Gas Units Only
Move lever down to
disengage belt idler.
Diesel Fuel Tank
Gasoline Tank
Choke
(Gas Units Only)
Throttle
Fast
Slow
4 INITIAL INSPECTION
8
4 INITIAL INSPECTION
4.1 GENERAL________________________________________________________________
The inspection and testing of the unit should always be
performed by a trained technician, familiar with the
operation of this equipment.
Read each instruction completely and make sure you
understand it before proceeding. Stay alert for potential
hazards and obey all safety precautions.
The RIGHT and LEFT, FRONT and REAR of the
machine are referenced from the operator’s seat, facing
forward.
Accessories not included with this product must be
ordered separately. See instructions provided with
accessory for installation and parts.
4.2 INITIAL INSPECTION_______________________________________________________
1. Perform a visual inspection of the entire unit, look for
signs of wear, loose hardware, and components that
may have been damaged during transport.
2. Inspect paint and decals for damage or scratches.
Decals provide important operating and safety
information. Notify dealer and replace all missing or
hard to read decals.
3. All fluids must be at the full level mark with engine
cold.
Check:
a. Radiator coolant level (Diesel Units).
b. Engine oil level.
c. Hydraulic fluid level.
4. Make sure air filter connections are tight and cover
is securely in place.
5. Check tires for proper inflation. Tires have been over
inflated for transport. Correct tire pressure should be
set to 3 - 5 psi (0.21 - 0.34 BAR).
6. Check belt tension.
[Parts & Maintenance Manual, Section 3.2]
7. Inspect battery connections and electrolyte level.
Check that battery is fully charged.
8. Check for fuel or oil leaks.
9. Inspect lube points on decks and unit for proper
lubrication.
[Parts & Maintenance Manual, Section 6.1]
10. Complete Pre-Delivery Inspection (PDI) forms and
return to Jacobsen Customer Service. (Dealer Only)
CAUTION
Do not attempt to drive the unit unless you are familiar
with this type of equipment and know how to operate
all controls correctly.
!
CAUTION
The initial inspection should be performed only when the engine is off and all fluids are cold. Lower attachments to
the ground, engage the parking brake, stop engine, and remove ignition key.
!
CONTROLS 5
9
5 CONTROLS
5.1 ICONS ___________________________________________________________________
WARNING
Never attempt to drive the unit unless you have read the Safety and Operation Manual and
know how to operate all controls correctly.
Familiarize yourself with the icons shown above and what they represent. Learn the
location and purpose of all the controls and gauges before operating this unit.
Glow Plug
Light
D
Read Manual Engine Throttle
High Low
Parking Brake
Engaged Disengaged
Fuel
Gasoline Diesel
Warning Lights
Battery Oil Water
Pressure Temp
Engine
Off Run Start
Headlight
ON OFF
Attachments
Rake Scarifier Blade
!
5 CONTROLS
10
A
B
C
D
E
F
G
H
J
L
K
L
M
N
P
R
B
1
B
2
S
Total Hours
1
10
0 0 0 0 0
A Steering Tilt Lever
B Parking Brake
C Traction Pedal
D Rake Control Lever
E Scarifier Control Lever (Optional)
F Blade Control Lever (Optional)
G Throttle
H Seat Adjuster
J Fuel Cap
K Access Panel
L Tool Holder
M Ignition Switch
N Hour Meter
P Light Switch
R Warning Light Panel
S 12 Volt Accessory Power Outlet
CONTROLS 5
11
5.2 CONTROL DESCRIPTIONS __________________________________________________
A.
Steering Tilt Control
Pull lever to release steering column. Tilt column up
or down to position desired. Release lever to lock
steering column in place.
B.
Parking Brake Lock / Release
To lock parking brake, hold brake pedal (B) down and
press lock (B
1
) until it engages. To disengage, press
brake pedal release (B
2
).
C.
Traction Pedal
Press front of pedal down for forward travel. Press
rear of pedal down for reverse travel. Release pedal
to slow unit and stop. Allow unit to come to a
complete stop before reversing directions. Do not
press traction pedal when parking brake is set.
D.
Rake Control Lever
Push forward to lower rake, pull back to raise rake.
NOTE:
Never operate in reverse with rake down.
Rake may fold under unit and damage rake and unit.
E.
Scarifier Lever (Optional)
Push forward to lower attachment, pull back to raise
attachment.
F.
Blade Control Lever (Optional)
Push forward to lower attachment, pull back to raise
attachment. To lock blade in float position, push lever
all the way forward.
G.
Throttle
Controls engine speed. Run machine at full throttle
during normal machine operation.
H.
Seat Adjustment
Pull left side lever out to adjust seat forward or
backward.
J.
Fuel Cap/Gauge
Displays fuel level. Read fueling instructions and the
engine manufacturer’s Owner’s Manual before
refueling.
K.
Access Panel
Open panel to access hydraulic reservoir.
L.
Tool Holder
A holder has been placed on each side of the hood to
store hand rakes, shovels, etc.
M.
Ignition Switch
The ignition switch has three positions. OFF - RUN -
START. See Section 6.4.
N.
Hour Meter
Records engine operating hours. Use hour meter to
schedule periodic maintenance.
P.
Light Switch
Controls operation of work lights.
R.
Warning Light Panel
Alerts the operator to conditions requiring immediate
action. See Section 5.3.
S.
12 Volt Accessory Power Outlet
Allows operation of approved 12 volt accessories and
attachments. To prevent excessive battery drain, only
use 12 volt outlet with engine running.
CAUTION
Never adjust steering while unit is moving. Stop unit
and set parking brake before adjusting.
!
CAUTION
The 12 Volt Accessory outlet circuit is protected by a
10 Amp fuse. Do not attempt to use attachment(s)
with a combined power rating greater than 120 Watts.
To prevent the risk or burns or fire do not replace 10
amp fuse with a higher amperage rating fuse.
!
5 CONTROLS
12
5.3 OPERATOR ALERTS_______________________________________________________
The electronic controller monitors vital machine systems.
It uses an audible alarm and warning lights to alert the
operator of conditions requiring immediate action. When
an alert occurs follow the general guidelines listed in the
chart below, and any specific actions outlined by the
grounds superintendent or service manager.
To test alarm system:
Turn ignition switch to RUN. All lights will come on for one
second or more and the alarm will sound briefly.
This system monitors:
T. Battery voltage
U. Engine oil pressure
V. Engine coolant temperature
W. Glow Plugs (Diesel Units)
Figure 5A
T
U
V
W
Alert Action
T. Battery Voltage - Warning light
comes on.
Return unit to a service area as soon as possible. Inspect battery and
battery charging system.
U. Engine Oil Pressure - alarm
sounds and oil pressure light
comes on. Oil pressure low.
Stop unit immediately, lower implements and shut off engine! Inspect oil
level in engine. If oil light remains on with oil at proper level, shut off engine,
and tow or trailer unit back to a service area. NEVER operate engine with oil
light on, severe damage to the engine can occur.
V. Engine Coolant Temperature
Alarm sounds. Engine coolant
temperature high. (Diesel Units
Only)
Stop unit immediately, lower implements and shut off engine! Remove
debris such as leaves and grass clippings that may be restricting air flow
through rear screen on hood and area between radiator and oil cooler. If
engine continues to run hot, return groomer to a service area.
CAUTION: Engine coolant is under pressure. Turn engine off and
allow fluid to cool before checking fluid level or adding coolant to
radiator.
W. Glow Plug - Glow plug light
comes on. (Diesel Units)
System is energizing glow plugs. Hold key in start position, starter will
engage when glow plug light turns off.
OPERATION 6
13
6 OPERATION
6.1 DAILY INSPECTION ________________________________________________________
1. Perform a visual inspection of the entire unit, look for
signs of wear, loose hardware, and missing or
damaged components. Check for fuel or oil leaks to
ensure connections are tight and hoses and tubes
are in good condition.
2. Check the fuel supply, radiator coolant level (Diesel
units), crankcase oil, and air cleaner indicator. All
fluids must be at the full level mark with engine cold.
3. Check tires for proper inflation.
4. Test the Interlock System.
Note: For more detailed maintenance information,
adjustments and maintenance/lube charts, see the
Parts & Maintenance manual.
6.2 INTERLOCK SYSTEM ______________________________________________________
1. The Interlock System prevents the engine from
starting unless the parking brake is engaged and the
traction pedal is in Neutral. The system also stops
the engine if the operator leaves the seat with the
traction pedal out of Neutral, or parking brake
disengaged.
2. Perform each of the following tests to insure the
Interlock System is functioning properly. Stop the
test and have the system inspected and repaired if
any of the tests fail as listed below:
The engine does not start in test 1;
The engine does start during tests 2 or 3;
The engine continues to run during test 4.
3. Refer to the chart below for each test and follow the
check () marks across the chart. Shut engine off
between each test.
Test 1:
Represents normal starting procedure. The
operator is seated, parking brake is engaged, and
the traction pedal is in Neutral.
Test 2:
The engine must not start if the parking brake
is DISENGAGED.
Test 3:
The engine must not start if traction pedal is
not in Neutral.
Test 4:
Start the engine in the normal manner then
disengage parking brake and lift your weight off the
seat. Engine must shut down.
Start engine, then lift your weight off seat. The engine will shut down.
CAUTION
The daily inspection should be performed only when
the engine is off and all fluids are cold. Lower
attachments to the ground, engage the parking brake,
stop engine, and remove ignition key.
!
WARNING
Never operate equipment with the Interlock
System disconnected or malfunctioning. Do not
disconnect or bypass any switch.
!
Test Operator
Seated
Parking
Brake
Traction Pedal
in Neutral
Engine
Starts
Yes No Engaged Disengaged Yes No Yes No
1
2
3
4
6 OPERATION
14
6.3 OPERATING PROCEDURES_________________________________________________
1. Under no circumstances should the engine be
started without the operator seated on the unit.
2. Never run the engine in an enclosed area.
3. Keep hands and feet away from moving parts. If
possible, do not make adjustments with the engine
running.
4. Do not operate unit or attachments with loose,
damaged, or missing components. Replace all worn
or damaged decals
5. Operate and rake in a flat test area to become
thoroughly familiar with the operation of the unit,
controls and rake.
6. Study the area to determine the best and safest
operating procedure. Consider the height and angle
of the bunker and whether it is wet or dry. Each
condition will require certain adjustments or
precautions. Enter and exit bunkers cautiously at the
lowest and flattest area.
7. Be aware of attachment discharge direction and
never direct discharge of material toward
bystanders, nor allow anyone near the machine
while in operation. The owner/operator is
responsible for injuries inflicted to bystanders and/or
damage to their property.
8. Slow down and raise the attachments when
crossing paths or roadways. Look out for traffic.
9. Stop and inspect the equipment for damage
immediately after striking an obstruction or if the
machine begins to vibrate abnormally. Have the
equipment repaired before resuming operation.
10. Operate engine at full throttle. Control speed by
using the forward/reverse pedals rather than the
engine throttle.
11. Slow down and use caution
12. Slow down and use extra care on hillsides. Read
Section 6.7. Use caution when operating near drop
offs.
13. Look behind and down before backing up to be sure
the path is clear. Use care when approaching blind
corners, shrubs, trees, or other objects that may
obscure vision.
Note:
Never operate in reverse with rake down. Rake
may fold under unit and damage rake and unit.
14. Never use your hands to clean attachments, use a
brush. Attachments may have extremely sharp
edges that can cause serious injuries
WARNING
A Roll Over Protection Structure (ROPS) is included with this groomer. Seat belts must be worn whenever operating
a groomer with a ROPS. Always keep seat belt snugly adjusted. DO NOT use seat belts on a groomer without a
ROPS.
If the groomer is overturning, hold onto the steering wheel. Do not attempt to jump out or leave the seat.
!
CAUTION
To prevent injury, always wear safety glasses, leather work shoes or boots, a hard hat, and ear protection. Long hair,
loose clothing, or jewelry may get tangled in moving parts
!
CAUTION
Before operating, pick up all debris such as rocks,
toys, and wire which can be thrown by the machine.
Enter a new area cautiously. Always operate at
speeds that allow you to have complete control of the
unit.
!
WARNING
Before you clean, adjust, or repair this equipment,
always disengage all drives, lower implements to the
ground, engage parking brake, stop engine, and
remove key from ignition switch to prevent injuries.
!
OPERATION 6
15
6.4 STARTING________________________________________________________________
IMPORTANT:
Do not use starting assist fluids.
Use of
such fluids in the air intake system may be potentially
explosive or cause a “Runaway” engine condition and
could result in serious engine damage.
1. Make sure the tow valve (See Section 6.9) is closed.
2. Sit in operator’s seat, make sure the parking brake
is engaged and traction pedal is in Neutral.
3. Move throttle lever between 1/8 to 1/2 throttle. Turn
ignition switch (M) to RUN. Battery (T), oil pressure
(U) and coolant temperature (V) lights should turn
on. Glow plug light (W) may also turn on (Diesel
Units).
4. Gas Units.
a. Pull choke lever to fully close choke plate.
b. Turn Ignition switch to START position and
release as soon as engine starts. Do not hold the
key in the start position for more than 15
seconds.
c. Slowly push choke lever in to open choke plate.
5. Diesel Units - Turn key to START position. Glow
plug light (W) will illuminate for about 3 to 5
seconds. Starter will engage when light goes out,
Release as soon as engine starts. The colder the
temperature, the longer it will take to energize plugs.
Do not hold switch in the START position for more
than 15 seconds.
6. As soon as the engine starts, warning lights (T, U
and V) should turn off. If any of the warning lights
do not shut off, stop the engine immediately and
have the unit serviced
7. Allow the engine to become warm and properly
lubricated before operating at high RPM.
Figure 6A
6.5 STOPPING / PARKING______________________________________________________
To stop:
Remove your foot from traction pedal. The unit will
automatically brake when the traction pedal returns to
Neutral.
To park the unit under normal conditions:
1. Raise the attachments and move away from the area
of operation.
2. Select a flat and level area to park.
a. Release traction pedal to bring the unit to a
complete stop.
b. Lower attachments to the ground, reduce throttle
to slow, and allow engine to operate at no load
for a minute.
3. Engage parking brake, stop the engine, and always
remove the ignition key.
If an emergency arises and the unit must be parked in the
area of operation, follow the guidelines outlined by the
grounds superintendent. If the unit is parked on an
incline, chock or block the wheels.
WARNING
To prevent injuries, sit in the seat, engage parking
brake, and place traction pedal in Neutral before
attempting to start the engine.
!
M
T
U
V
W
Total Hours
1
10
0 0 0 0 0
6 OPERATION
16
6.6 TO DRIVE / TRANSPORT____________________________________________________
Read and follow all safety notes contained in this manual
when driving or transporting unit. Refer to Section 6.3 for
general operating instructions. When operating in reverse
look behind you to ensure you have a clear path.
Important: If this unit is driven on public roads, it must
comply with federal, state, and local ordinances. Contact
local authorities for regulations and equipment
requirements.
1. Fully raise attachments when driving to and from the
area of operation.
2. Disengage parking brake and move throttle lever to
“Fast”. Depress traction pedal slowly.
6.7 HILLSIDE OPERATION _____________________________________________________
The unit has been designed for good traction and stability
under normal operating conditions; however, use caution
while operating on slopes, especially when the sand or
grass is wet. Wet terrain reduces traction and steering
control.
1. Always operate with the engine at full throttle. Control
groomer speed using traction pedal.
2. If the unit tends to slide or the tires begin to “mark”
the terrain, angle unit into a less steep grade until
traction is regained or tire marking stops.
3. If unit continues to slide or mark the terrain, the
grade is too steep for safe operation. Do not make
another attempt to climb, raise rake, and back down
slowly.
4. Correct tire pressure is essential for maximum
traction.
Front and Rear.......... 3-5 psi - (0.21-0.34 BAR)
Figure 6B
Figure 6C
CAUTION
To prevent tipping or loss of control, travel at reduced
speed when making turns.
!
WARNING
To minimize the possibility of overturning, the safest
method for operating on hills and terraces is to travel
up and down the face of the slope (vertically), not
across the face (horizontally). Avoid unnecessary
turns, travel at reduced speeds, stay alert for hidden
hazards, and drop offs.
To prevent tipping or loss of control, do not start or
stop suddenly on slopes. Reduce speed when making
sharp turns. Use caution when changing directions.
WARNING
Do not operate this unit on slopes greater than 15°
!
!
Maximum 15° Slope
Maximum 15° Slope
0°
Degrees are shown to nearest 1/4°
General Slope of Roadway Embankment - 45°
Steepest Grass Area - 31°
Slope of Average Roof - 19-1/4°
2nd Class Highway Maximum Grade - 4-1/2°
Toll Road or Freeway - 1-3/4°
0%
2-3/4°
5%
5-3/4°
10%
8-1/2°
15%
11-1/4°
20%
14°
25%
16-3/4°
30%
19-1/4°
35%
21-3/4°
40%
24-1/4°
45%
26-1/2°
50%
28-3/4°
55%
31°
60%
33°
65%
35°
70%
36-3/4°
75%
38-3/4°
80%
40-1/4°
85%
42°
90%
43-1/2°
95%
45°
100%
Degrees
Grade
OPERATION 6
17
How to calculate a slope:
Tools Required:
Level (A), either 1 yard, or 1 meter long.
Tape measure (B).
With the level (A) positioned horizontally, measure the
distance (C) with tape measure (B). Use the chart to
calculate eirther the slope angle or the % grade of the
slope (D).
Figure 6D
C
A
B
D
Height (C) Result (D)
Inches with 1 Yard Level (A) Millimeters with 1 Meter Level (A) Slope in Degrees Slope Grade %
3
4.8 8.3
100 5.7 10.0
150 8.5 15
6
9.5 16.7
200 11.3 20.0
7.5
11.8 20.8
225 12.7 22.5
9 250 14 25.0
275 15.4 27.5
10
15.5 27.8
300 16.7 30.0
11
17.0 30.6
325 18.0 32.5
12
18.4 33.3
350 19.3 35.0
13
19.9 36.1
375 20.6 37.5
14
21.3 38.9
400 21.8 40.0
15
22.6 41.7
425 23.0 42.5
16
24 44.4
475 25.4 47.5
18 500 26.6 50.0
20
29.1 55.6
600 31.0 60.0
25
34.8 69.4
800 38.7 80.0
30
39.8 83.3
900 42.0 90
36 1000 45.0 100
6 OPERATION
18
6.8 ATTACHMENTS___________________________________________________________
The Groom Master will accept several attachments
designed to perform a variety of operations. Before
installing and using attachments read and save the
instruction sheet included with it.
Contact your Jacobsen Distributor for a complete list of
attachments and accessories available for your machine.
6.9 TOWING / TRAILERING _____________________________________________________
If the unit experiences problems and removed from the
area, it should be loaded onto a trailer for transport. If a
trailer is not available, the unit can be towed slowly short
distances.
Use care when loading and unloading unit. Fasten unit to
trailer to prevent it from rolling or shifting during transport.
Before towing, open tow valve. The tow valve permits
moving the unit without starting the engine and prevents
possible damage to hydraulic components.
The tow valve (A) is located on the hydraulic drive pump
under rear hood. To open valve, insert a pin into the small
hole in the valve stem. Turn the valve counterclockwise
one full turn.
Before towing make sure attachments are raised. If they
cannot be raised, remove them from the unit.
Close valve completely after towing.
NOTE:
Do not exceed 1 MPH (1.6 KPH) while towing.
Long distance towing is not recommended.
f
Figure 6J
A
TRG004
OPERATION 6
19
6.11 DAILY MAINTENANCE______________________________________________________
Important: For more detailed maintenance information,
adjustments, and maintenance/lubrication charts, see
the Parts & Maintenance manual.
1. Park the unit on a flat, level surface. Fully lower the
attachments to the ground, engage parking brake,
stop the engine, and remove key from ignition switch.
2. Grease and lubricate all points if required. To
prevent fires, wash the unit after each use.
a. Use only fresh water for cleaning your
equipment.
Note:
Use of salt water or effluent water has been
known to encourage rust and corrosion of metal parts
resulting in premature deterioration or failure.
Damage of this nature is not covered by the factory
warranty.
b. Do not use high pressure spray.
c. Do not spray water directly at the instrument
panel, or any electrical components.
d. Do not spray water into the cooling air intake or
the engine air intake.
Note:
Do not wash a hot or running engine. Use
compressed air to clean the engine and radiator fins.
e. Clean the tires thoroughly. Check tire pressure.
f. Clean radiator and oil cooler passages using
compressed air (30 psi (2 BAR) maximum).
3. Fill unit’s fuel tank at the end of each operating day
to within 1 in., (25 mm) below the filler neck.
Diesel Engine - Use clean, fresh, #2 low or ultra low
sulfur diesel fuel. Minimum Cetane Rating 45.
Gasoline Engine - Use clean, fresh, unleaded
gasoline, 85 octane minimum.
4. Handle fuel with care - it is highly flammable. Use
an approved container, the spout must fit inside the
fuel filler neck. Avoid using cans and funnels to
transfer fuel.
a. Never remove the fuel cap from the fuel tank, or
add fuel, when the engine is running, or while the
engine is hot.
b. Do not smoke when handling fuel. Never fill or
drain the tank indoors.
c. Never overfill or allow the tank to become empty.
Do not spill fuel. Clean any spilled fuel
immediately.
d. Never handle or store fuel containers near an
open flame or any device that may create sparks
and ignite the fuel or fuel vapors.
5. Store fuel according to local, state, or federal
ordinances and recommendations from your fuel
supplier.
6. Inspect hydraulic hoses and tubes daily. Look for
wet hoses or oil spots and replace worn or
damaged hoses and tubes before operating the
machine.
7. After engine has cooled, check coolant level.
Radiator should be full and recovery bottle should be
up to the cold mark.
8. Park machine in designated area. Engage parking
brake and remove key. Do not part
equipment near
an open flame or spark which could ignite fuel or fuel
vapors.
Place key in a secure location to prevent
unauthorized use of equipment.
9. Check the engine oil and hydraulic oil at the start
and end of each day. If the oil level is low, remove
the oil filler cap, and add oil as required. Do not
overfill.
WARNING
To prevent serious injury from hot, high pressure oil,
never use your hands to check for oil leaks, use paper
or cardboard.
Hydraulic fluid escaping under pressure can have
sufficient force to penetrate skin. If fluid is injected into
the skin, it must be surgically removed within a few
hours by a doctor familiar with this form of injury or
gangrene may result.
WARNING
To prevent serious bodily injury from hot coolant or
steam blow-out, never attempt to remove the radiator
cap while the engine is running. Stop the engine and
wait until it is cool. Even then, use extreme care when
removing the cap.
CAUTION
Do not pour cold water into a hot radiator. Do not
operate engine without a proper coolant mixture.
Install cap and tighten securely.
!
!
!
6 OPERATION
20
6.12 LONG TERM STORAGE ____________________________________________________
General
1. Wash the unit thoroughly and lubricate. Repair and
paint damaged or exposed metal.
2. Inspect the unit, tighten all hardware, and replace worn
or damaged components.
3. Drain and refill radiator.
4. Clean the tires thoroughly and store the unit so the
load is off the tires. If unit is not on jack stands, check
tires at regular intervals and reinflate as necessary.
5. Keep the machine and all its accessories clean, dry
and protected from the elements during storage. Never
store equipment near an open flame or spark which
could ignite fuel or fuel vapors.
Battery
1. Remove, clean and store battery in upright position on a
non-conductive surface (wood) in a cool, dry place. To
prevent accelerated discharge, do not store battery on
concrete or steel surface.
2. Check and recharge battery every 60 to 90 days while
in storage.
3. Store batteries in a cool, dry place. To reduce the self
discharge rate, room temperature should not be above
80°F (27°C) or fall below 20°F (-7°C) to prevent
electrolyte from freezing.
Engine
1. While the engine is warm, remove drain plug, drain the
oil from the crankcase, and change oil filter. Install drain
plug and refill with fresh oil. Torque drain plug to 22 ft. lb.
(30 Nm).
2. Clean exterior of engine. Paint exposed metal or apply
a light coat of rust preventative oil.
3. Add a fuel conditioner or biocide to prevent gelling or
bacterial growth in fuel. See your local fuel supplier.
Attachments
1. Wash the attachments thoroughly, then repair and paint
any damaged or exposed metal.
2. Lubricate all fittings and friction points.
After Storage
1. Check and reinstall battery.
2. Check or service fuel filter and air cleaner.
3. Check the radiator coolant level.
4. Check oil level in the engine crankcase and hydraulic
system.
5. Fill the fuel tank with fresh fuel. Bleed the fuel system.
6. Make certain that the tires are properly inflated.
7. Start and operate the engine at 1/2 throttle. Allow
enough time for the engine to become properly
warmed and lubricated.
WARNING
Never operate the engine without proper ventilation;
exhaust fumes can be fatal when inhaled.
!
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
Ransomes 88010, 88042 Owner's manual
- Category
- Lawnmowers
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Ransomes 88008 Owner's manual
-
-
-
-
-
-
-
-
Textron USAD004 Owner's manual
-
