Gossen MetraWatt SECULIFE IF+ Installation guide

Gossen MetraWatt
Brand
Gossen MetraWatt
Model
SECULIFE IF+
Type
Installation guide

Gossen MetraWatt SECULIFE IF+ is a high-precision Infusion Pump Analyzer (IPA) designed to test the flow rate of intravenous (I. V.) infusion pumps. It can simultaneously test two volumetric pumps for output flow rate using two volumetric chambers.

The device has two connector sockets at the back for connecting chambers, and a Power terminal. It connects to the chamber via an 8-pin Mini-DIN cable, and to the infusion pump via Luer Lock Tube.

The SECULIFE IF+ features a graphical LCD display that shows the flow rate in milliliters per hour, and level indicators to identify the level of water in each chamber.

Gossen MetraWatt SECULIFE IF+ is a high-precision Infusion Pump Analyzer (IPA) designed to test the flow rate of intravenous (I. V.) infusion pumps. It can simultaneously test two volumetric pumps for output flow rate using two volumetric chambers.

The device has two connector sockets at the back for connecting chambers, and a Power terminal. It connects to the chamber via an 8-pin Mini-DIN cable, and to the infusion pump via Luer Lock Tube.

The SECULIFE IF+ features a graphical LCD display that shows the flow rate in milliliters per hour, and level indicators to identify the level of water in each chamber.

QUICK SETUP
GUIDE
SECULIFE IF
+
The SECULIFE IF+ is a microprocessor based high precision Infusion Pump Analyzer (IPA). It tests the flow of intravenous (I. V.) infusion
pumps. The flow rates are displayed in milliliters per hour. Simultaneously the unit can test two volumetric pumps for output flow rate using
two volumetric chambers.
1. SECULIFE IF
+
1
8-pin Mini-Din connector for connection to Chamber 1/
Chamber 2
Terminal for power supply unit (2.1 mm)
LCD graphical display
Operating panel (6 light touch keys)
9 V battery compartment (back)
2.
Chambers (3.5 mL or 35 mL)
3. 8-pin Mini-Din cable
4. Luer Lock tube
2
8 pin Mini-Din connector for connection to SECULIFE IF+
Luer Lock connection for fluid supply
Connection of Infusion Pump Testers
The device hast two connector sockets at the back for connecting Chamber 1 / Chamber 2. They are connected by an 8-pin Mini-Din plug.
Additionally, there is a Power terminal at the back.
1.) Connection of SECULIFE IF+ and Chamber
SECULIFE IF+ is connected with the chamber (3.5 ml or 35 ml)
via an 8-pin Mini-DIN cable. The connection is established by plugging the grey cable into the Chamber 1/ Chamber 2 port at the
SECULIFE IF+ and into the terminal located at the right side of the chamber.
Following the device is switched on at the operating panel.
3
2.) Connection between infusion pump and chamber
In the next step the infusion pump is connected to the chamber via Luer Lock Tube
3.) Functional test
The first step of the functional test is setting the flow rate (e.g. 200 ml/h) and pressing the start button to start the pump. The fluid located
in the Luer Lock Tube moves into the chamber. At the same time a timer is set by the SECULIFE IF+. Afterwards the result is shown on the
display of the SECULIFE IF+. This is shown in the right picture, highlighted in green.
4
4.) Reading the result
As a final step, the flow rate is checked by comparing the flow rate set at the infusion pump (here: 200 ml/h) with the value displayed at the
SECULIFE IF+ (here: 198.6 ml/h).
The flow accuracy of the SECULIFE IF+ equals +/- 1%.
5.) Transport protection
The switch lock prevents an accidental switch on e.g. during transport.
5
Level Indicator
A special graphic has been incorporated into the display to identify the level of water in each chamber.
The graphic is located at the lower right corner of the display for each channel.
This graphic indicates that water is not present at the lower or upper sensor.
This graphic indicates that fluid is present at the lower sensor.
These graphics are displayed sequentially to indicate that a test is running.
This graphic indicates that water is detected at the top and bottom sensor.
This graphic indicates that water is present at the top sensor, but not the bottom. This is an invalid condition, triggered by
either a bubble at the bottom sensor or a faulty sensor.
Setup
The Setup Mode allows the user to adjust the configuration of the meter. The setup screen can be
entered using the key. The parameters can be changed by using key to highlight the
line and to toggle between the available options.
The Setup screen can be exited using the key.
6
GMC-I Messtechnik GmbH
Südwestpark 15 □ 90449 Nürnberg □ Germany
TEL +49 911 8602-111 □ FAX +49 911 8602-777
www.gossenmetrwawatt.com □ [email protected]
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Gossen MetraWatt SECULIFE IF+ Installation guide

Gossen MetraWatt
Brand
Gossen MetraWatt
Model
SECULIFE IF+
Type
Installation guide

Gossen MetraWatt SECULIFE IF+ is a high-precision Infusion Pump Analyzer (IPA) designed to test the flow rate of intravenous (I. V.) infusion pumps. It can simultaneously test two volumetric pumps for output flow rate using two volumetric chambers.

The device has two connector sockets at the back for connecting chambers, and a Power terminal. It connects to the chamber via an 8-pin Mini-DIN cable, and to the infusion pump via Luer Lock Tube.

The SECULIFE IF+ features a graphical LCD display that shows the flow rate in milliliters per hour, and level indicators to identify the level of water in each chamber.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents