Contec PWA-84AWD1 Owner's manual

Type
Owner's manual
SWITCHING AC ADAPTER (12VDC 7.0A)
PWA-84AWD1 Users Guide
CONTEC CO.,LTD.
Thank you for purchasing this product.
This product is the AC adapter for input: 90 - 264VAC and output: +12VDC 7.0A. This product can be used for the
CONTEC’s following models. (Don’t use this product with any other devices.)
- PWA-84AWD1
Digital Signage Player: DS-380D-DCxxxx
Package Contents
- AC adapter …1 - User’s Guide (this booklet)1
- AC power cable (100VAC, 3pin)*1*2 …1 - Warranty Certificate 1
- Conversion cable …1 - Serial number label1
*1 This AC power cable is for the voltage of the 100VAC or less.
In the case that the voltage that this cable uses do not match you need to prepare other cable particularly.
*2 Do not use this AC power cable with any devices except for an attached AC adapter.
AC adapter
AC power cable
(100VAC, 3pin)
Conversion cable
Warranty
Certificate
Users Guide
(this document)
Serial number
label
Usage environment
It is expected that you will use this product in a comparatively good environment.
If you will use it in a harsh environment or if you require a long service life from it, we ask that you separately prepare a
power supply that fits your application.
If the AC adapter fails, CONTEC will replace it with an equivalent product (a charge may be applied to the replacement).
Also, note that we cannot provide analyses of failure causes.
Disposal
When disposing of the product, follow the disposal procedures stipulated under the relevant laws and municipal
ordinances.
Storage
When storing this product, keep it in its original packing form.
(1) Wrap it in the packing material, and then put it in the box.
(2) Store the package at room temperature at a place free from direct sunlight, moisture, shock, vibration, magnetism, and
static electricity.
Safety Information
This document provides safety information using the following symbols to prevent accidents resulting in injury or death
and the destruction of equipment and resources. Understand the meanings of these labels to operate the equipment safely.
DANGER
WARNING
CAUTION
Handling Precautions
DANGER
- Do not use the product in locations exposed to a flammable or corrosive gas. It may cause explosion, fire, electrical
shock, or malfunction.
- To avoid electrocution, do not use the product with a wet hand.
- Be sure to connect the product to the stipulated power supply voltage. Connecting to a different voltage might cause a
fire or electrical shock.
- Never disassemble or modify the product or replace its parts in order to prevent electrical shock, fire, or malfunction.
CONTEC reserves the right to refuse servicing the product modified by the user. When any part of the product needs
to be replaced at the expiration of its life or due to breakdown, please contact the CONTEC sales representative or sales
office.
WARNING
- If you sense abnormality (smoke, odor, or noise), immediately unplug the power cord from the wall outlet and contact
the CONTEC sales representative or sales office.
- Do not use the product with the other power device. It may cause fire or malfunction.
- When the cable or main body is damaged, stop using and repair it immediately. Using it as it is may cause fire,
electrical shock or malfunction.
- Use the product with the specified models by the CONTEC. Not doing so may cause fire or malfunction.
- Use the product in the specified operating condition (temperature and humidity)
CAUTION
- Do not use or store the product in a location exposed to extremely high or low temperature or susceptible to a rapid
temperature change. Example:
- Exposure to direct sun - In the vicinity of a heat source
- When unplugging the cable, hold the plug. Holding and pulling the cable itself can cause a failure such as discontinuity.
- To clean the product wipe it gently with soft cloth damp with either water or mild detergent.
Do not use chemicals or a volatile solvent, such as benzene and thinner, to prevent peeling or discoloration of the paint.
- When transporting the product, provide adequate measures to protect it from vibration or shock.
Copyright
Copyright 2014 CONTEC CO., LTD. All Rights Reserved.
No part of this document may be copied or reproduced in any form by any means without prior written consent of
CONTEC CO., LTD.
CONTEC CO., LTD. makes no commitment to update or keep current the information contained in this document.
The information in this document is subject to change without notice.
All relevant issues have been considered in the preparation of this document. Should you notice an omission or any
questionable item in this document, please feel free to notify CONTEC CO., LTD.
Regardless of the foregoing statement, CONTEC assumes no responsibility for any errors that may appear in this
document or for results obtained by the user as a result of using this product.
Using method
- Make sure that the AC power cable is not plugged into a wall outlet.
- Connect the AC power cable to the main body of AC adapter connector (CN1).
- Connect the DC cable of AC adaptor with the DC power supply connector.
- Plug the AC power cable into a wall outlet.
* This product has no power switch. When turning off, unplug the AC power cable from the wall outlet.
Specifications
Requirement
Description
Power supply space
Rated input voltage
100 - 240VAC (continuous input), 50 - 60Hz
Permissible input voltage
90 - 264VAC, 47 - 63Hz
Input current
1.3A Max. (100VAC)
Rated output voltage
+12VDC±5%
Rated output current
7.0A (Max.)
Hold up time
20ms or less
Dielectric strength
(between Input P and S)
1.5kVAC for one second
Insulation resistance
(between P and S)
Greater than 50M (500VDC)
Environmental specs
Surrounding temperature
Operating: 0 to +40 ºC
Storage: -30 to +60 ºC
Surrounding humidity
Operating: 8 - 80%RH (No condensation)
Storage: 8 - 90%RH (No condensation)
Floating dust particles
Not to be excessive
Corrosive gases
None
Others
Cable length
AC power cable: 2m, DC cable: 1.5m, Conversion cable: 220mm
External dimensions (mm)
58(W) x 160(D) x 32(H) (not include projection of cable)
Weight
Main body: 500g, AC power cable: 180g
MTBF *1
30,000H (temperature 25 ºC)
Life *1
7,800H (Operating temperature 25 ºC)
*1 Note that MTBF and life is only referential value, not guaranteed value.
External Dimensions and Component Identification
160
58
32
1500±100
[mm]
Copyright 2014 CONTEC CO., LTD. All Rights Reserved.
CONTEC CO.,LTD.
3-9-31, Himesato, Nishiyodogawa-ku, Osaka 555-0025, Japan
July 2014 Edition
Japanese http://www.contec.co.jp/ English http://www.contec.com/
Chinese http://www.contec.com.cn/
NA03408 (LYRN861)
[07142014]
No part of this document may be copied or reproduced in any form by any means without prior written consent of CONTEC CO., LTD.
  • Page 1 1

Contec PWA-84AWD1 Owner's manual

Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI