Contec PCB100WS Owner's manual

Contec
Brand
Contec
Model
PCB100WS
Type
Owner's manual

Contec PCB100WS is a cable that converts a 100-pin connector of the interface made of CONTEC board into a 37-pin D-SUB male connector. It is available in three lengths: 1.5m, 3m, and 5m. The cable has a 100 core shield cable with AWG#30 conductor size and weighs 420g, 640g, and 940g for the 1.5m, 3m, and 5m lengths, respectively.

The PCB100WS is designed to be used with CONTEC boards that have a 100-pin connector. It can be used to connect a CONTEC board to a device with a 37-pin D-SUB connector, such as a computer or a printer.

Contec PCB100WS is a cable that converts a 100-pin connector of the interface made of CONTEC board into a 37-pin D-SUB male connector. It is available in three lengths: 1.5m, 3m, and 5m. The cable has a 100 core shield cable with AWG#30 conductor size and weighs 420g, 640g, and 940g for the 1.5m, 3m, and 5m lengths, respectively.

The PCB100WS is designed to be used with CONTEC boards that have a 100-pin connector. It can be used to connect a CONTEC board to a device with a 37-pin D-SUB connector, such as a computer or a printer.

1
PCB100WS-1.5, PCB100WS-3, PCB100WS-5
Connection Conversion Shield Cable
(100pin→37pin D-SUBx2)
PCB100WS-1.5, PCB100WS-3,
PCB100WS-5 User’s Guide
CONTEC CO.,LTD.
The PCB100WS-1.5, PCB100WS-3, and PCB100WS-5 are cables which converts 100-pin connector of
the interface made of CONTEC board into 37-pin D-SUB male connector.
External Dimensions
19
201
37
44.1mm
70.5mm
46.44mm
9mm
58.7mm
CNA
1
50
100
51
15.0mm
PCB100WS-1.5
PCB100WS-3
PCB100WS-5
1,500mm
3,000mm
5,000mm
CNB
CNA
CNB
Specifications
Item Specification
100-pin 0.8mm-pitch connector HDRA-E100MA1 [HONDA] or equivalent
Thumb screw: M2
Connector
37-pin D-SUB, male connector
17JE-23370-02(D8C)[DDK] or equivalent
Cable 100 core shield cable. Conductor size: AWG#30 Conductor composition: 7pcs/0.1mm UL20276
Weight
420g(PCB100WS-1.5), 640g(PCB100WS-3), 940g(PCB100WS-5)
Notes!
- Do not strike or bend the product. Otherwise, the product may malfunction, overheat, cause a
failure or breakage.
- Do not insert or remove the connector while the power is turned on to the PC. Failure to observe
this precaution may cause malfunction, overheating.
- Insert or remove the cable straightly. Otherwise, the part of connector may distort, cause a failure
or breakage.
- The specifications of this product are subject to change without notice for quality improvement.
Even when using the product continuously, be sure to read the manual and understand the contents.
- Regardless of the foregoing statement, CONTEC assumes no responsibility for any errors that may
appear in this document or for any results of using the product.
- All relevant issues have been considered in the preparation of this document. Should you notice an
omission or any questionable item in this document, please feel free to notify CONTEC CO., LTD.
PCB100WS-1.5, PCB100WS-3, PCB100WS-5 User’s Guide
Copyright 2002 CONTEC CO., LTD. ALL RIGHTS RESERVED.
CONTEC CO., LTD. May 2008 Edition
3-9-31, Himesato, Nishiyodogawa-ku, Osaka 555-0025, Japan
Japanese http://www.contec.co.jp/
English http://www.contec.com/ A-46-669 (LYBT323)
Chinese http://www.contec.com.cn/ 05212008_rev7[07262002]
No part of this document may be copied or reproduced in any form by any means without prior written
consent of CONTEC CO., LTD.
Connection Diagram
100-pin
connector
100-pin
connector
CN1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
CN1
CNA
37-pin D-SUB
connector
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
CNB
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
37-pin D-SUB
connector
  • Page 1 1
  • Page 2 2

Contec PCB100WS Owner's manual

Contec
Brand
Contec
Model
PCB100WS
Type
Owner's manual

Contec PCB100WS is a cable that converts a 100-pin connector of the interface made of CONTEC board into a 37-pin D-SUB male connector. It is available in three lengths: 1.5m, 3m, and 5m. The cable has a 100 core shield cable with AWG#30 conductor size and weighs 420g, 640g, and 940g for the 1.5m, 3m, and 5m lengths, respectively.

The PCB100WS is designed to be used with CONTEC boards that have a 100-pin connector. It can be used to connect a CONTEC board to a device with a 37-pin D-SUB connector, such as a computer or a printer.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents