EZ-FLO 10675 Installation guide
- Category
- Sanitary ware
- Type
- Installation guide
This manual is also suitable for
Single Control
Tub & Shower Trim Kit
Before You Begin
Check to make sure you have the following:
10675
10677
Tools and Supplies
You will need the following to install your new faucet:
Groove
Joint Pliers
Pipe
Tape
Adjustable
Wrench
Phillips
Screwdriver
• For use with an automatic compensating valve
rate at 1.56 gpm (5.9 L/min) or less.
• This product is engineered to meet the EPA
WaterSense flow requirement. The flow rate is
governed by the flow controller. If replacement
is ever required, be sure to replace it with a
WaterSense compliant flow controller to retain
the water conserving flow rate of this product.
Shut off main water supply before installation.
Faucet Installation
1 Shut off water supply. 2 Install shower flange and
shower arm.
3 Install showerhead
and tighten with
wrench.
4 Install nipple for spout. The
distance from the valve to the
tub spout stub out should be
between 8" (20 cm) and 18" (45
cm).
5A Installation on 1/2" Copper Pipe
(5/8" OD):
Slip on installation over 1/2" copper pipe:
Back out set screw in bottom of spout to
allow spout to slide on stub out pipe.
Slide the flange and spout over the pipe
with the spout tight to the wall, tighten
the set screw to the pipe.
5B Threaded installation with 1/2" Steel or
Brass Pipe(7/8" OD):
Apply pipe sealant tape on the pipe nipple
threads. Before installing spout, remove the
adapter assembly (including plastic
adapter, plastic washer, O-Ring) by
backing out the set screw and pulling out
the copper tube adapter assembly. Slide
the flange and spout over the pipe; with the
spout tight to the wall, tighten the set screw
to the pipe.
6 Before installing
escutcheon, remove the plastic
cap from plaster guard by
twisting cap to the clockwise.
8 Screw in handle.
8"~18"
203mm~457mm
Ø 5/8"
(Ø 15.9mm)
1 3/8"~2"
(35mm~51mm)
1/2"-14NPT
1 5/8"~1 11/16"
(41mm~43mm)
7 Install escutcheon and sleeve onto
valve.
1 Shower Arm Flange A019001-S
2 Shower Arm A020002
3 Shower Head 1.75gpm S1213606
4 Handle Cap A663376
5 Metal Handle Assembly A66E563
6 Screw Set A608563
7 Escutcheon Assembly A66F548-S
8 Sleeve A103322
9 Hex Wrench (H3.18 *20 MM L * 90 MM L) A031017NI
10 Spout Escutcheon A303070
11 Spout W/Diverter A523010
Troubleshooting Guide
Problem Cause Solution
Keep this manual for ordering replacement parts.
Replacement Parts
Leaks underneath handle. Cartridge has come loose or o-ring
on cartridge is dirty or twisted.
Tighten the cartridge by turning it clockwise. Move the
cartridge stem to the “on” position. If either o-ring is
twisted, straighten it out. If either o-ring is damaged,
replace it.
Minor problems often can be fixed without a plumber. Before doing any work on the faucet, shut off water supply and
close stopper or drain to avoid losing small parts.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
-
1
-
2
-
3
EZ-FLO 10675 Installation guide
- Category
- Sanitary ware
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI