Kichler Lighting 42588OZ User manual

Brand
Kichler Lighting
Model
42588OZ
Type
User manual

This manual is also suitable for

1) Pass wire from fixture through stem and screw stem to top of
fixture. NOTE: Thread locking compound must be applied to
all stem threads as noted with symbol (3) to prevent
accidental rotation of fixture during cleaning, relamping, etc.
2) Pass fixture wire through remaining stems and screw stems
together.
3) Thread one small threaded pipe into end of each small loop.
4) Pass fixture wire through first loop. Thread first loop onto
end of last stem.
5) Pass fixture wire through second loop and through hole in
canopy.
6) Pass threaded pipe at end of second loop through hole in
canopy.
7) Pass fixture wire through hole in lockwasher. Thread
lockwasher onto end of threaded pipe protruding from
inside canopy.
8) Pass fixture wire through hole in hexnut. Thread hexnut onto
end of threaded pipe.
9) Attach chain link to small loop at end of stem and to loop on
canopy.
10) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF”
position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room
that you are working on.
c) Place the wall switch in the “OFF” position. If the fixture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
11) Find the appropriate threaded holes on mounting strap.
Assemble mounting screws into threaded holes.
12) Attach mounting strap to outlet box. (Screws not provided).
Mounting strap can be adjusted to suit position of fixture.
13) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a
hole and two raised dimples. Wrap ground wire from
outlet box around green ground screw, and thread into
hole.
B) On fixtures where a cupped washer is provided. Attach
ground wire from outlet box under cupped washer and
green ground screw, and thread into mounting strap.
If fixture is provided with ground wire. Connect fixture
ground wire to outlet box ground wire with wire connector
(not provided.) after following the above steps. Never
connect ground wire to black or white power supply wires.
14) Make wire connections (connectors not provided). Reference
chart below for correct connections and wire accordingly.
15) Push fixture to ceiling, carefully passing mounting screws
through holes in canopy.
16) Thread knurl knobs onto mounting screws. Tighten knurl
knobs to secure fixture to ceiling.
17) Insert recommended bulbs.
18) Raise glass up to fixture. Pass hole in glass over socket cluster.
19) Fit top edge of glass inside cup of fixture body.
20) Thread finials into each hole along side of cup of fixture.
Carefully tighten finials to secure glass in place.
MOUNTING STRAP
ABRAZADERA DE MONTAJE
CANOPY
ESCUDETE
Date Issued: 5/30/14 IS-42588-US
GREEN GROUND
SCREW
CUPPED
WASHER
A
B
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
(NOT PROVIDED)
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth)
*Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.
KNURL KNOB
PERILLA ESTRADA
SMALL LOOP
ARGOLLA PEQUEÑA
CHAIN LINK
ESLABÓN DE
CADENA
STEM
VASTAGO
GLASS
VIDRIO
3
FIXTURE BODY
CUERPO DEL ARTEFACTO
3
3
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
HENXUT
TUERCA HEXAGONAL
LOCKWASHER
ARANDELA DE
SEGURIDAD
CUP
TAZA
FINIAL
CAPUCHON
SOCKET CLUSTER
GRUPO DE PORTALÁMPARAS
Page is loading ...
1) Pass wire from fixture through stem and screw stem to top of
fixture. NOTE: Thread locking compound must be applied to
all stem threads as noted with symbol (3) to prevent
accidental rotation of fixture during cleaning, relamping, etc.
2) Pass fixture wire through remaining stems and screw stems
together.
3) Thread one small threaded pipe into end of each small loop.
4) Pass fixture wire through first loop. Thread first loop onto
end of last stem.
5) Pass fixture wire through second loop and through hole in
canopy.
6) Pass threaded pipe at end of second loop through hole in
canopy.
7) Pass fixture wire through hole in lockwasher. Thread
lockwasher onto end of threaded pipe protruding from
inside canopy.
8) Pass fixture wire through hole in hexnut. Thread hexnut onto
end of threaded pipe.
9) Attach chain link to small loop at end of stem and to loop on
canopy.
10) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF”
position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room
that you are working on.
c) Place the wall switch in the “OFF” position. If the fixture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
11) Find the appropriate threaded holes on mounting strap.
Assemble mounting screws into threaded holes.
12) Attach mounting strap to outlet box. (Screws not provided).
Mounting strap can be adjusted to suit position of fixture.
13) Make wire connections (connectors not provided.) Reference
chart below for correct connections and wire accordingly.
14) Push fixture to ceiling, carefully passing mounting screws
through holes in canopy.
15) Thread knurl knobs onto mounting screws. Tighten knurl
knobs to secure fixture to ceiling.
16) Insert recommended bulbs.
17) Raise glass up to fixture. Pass hole in glass over socket cluster.
18) Fit top edge of glass inside cup of fixture body.
19) Thread finials into each hole along side of cup of fixture.
Carefully tighten finials to secure glass in place.
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth)
*Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
Date Issued: 5/30/14 IS-42588-CB
INSTRUCTIONS
For Assembling and Installing Fixtures in Canada
Pour L’assemblage et L’installation Au Canada
MOUNTING STRAP
PATTE DE FIXATION
CANOPY
CACHE
KNURL KNOB
BOUTON MOLETÉ
SMALL LOOP
PETITE BOUCLE
STEM
TIGE
CHAIN LINK
MAILLON DE LA CHAÎNE
4
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
4
SEE OTHER SIDE FOR CANADIAN FRENCH TRANS-
LATIONS.
VOIR L’AUTRE CÔTÉ POUR LES CANADIENS TRA-
DUCTIONS EN FRANÇAIS.
4
GLASS
VERRE
SOCKET CLUSTER
GROUPE DE DOUILLES
HEXNUT
ECROU HEXAGONAL
LOCKWASHER
RONDELLE DE BLOCAGE
FINIAL
ORNEMENT
CUP
COUPE
FIXTURE BODY
LUMINAIRE
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Kichler Lighting 42588OZ User manual

Brand
Kichler Lighting
Model
42588OZ
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents