NXP KIT34FS6407EVB User guide

Brand: NXP

Model: KIT34FS6407EVB

Type: User guide

This manual is also suitable for

KIT34FS6408EVB

Freescale Semiconductor, Inc.

User’s Guide

Document Number: KT34FS6407-34FS6408UG

Rev. 1.0, 8/2015

KIT34FS6407EVB and KIT34FS6408EVB

Evaluation Board

Figure 1. KIT34FS6407EVB and KIT34FS6408EVB Board

KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015

2 Freescale Semiconductor, Inc.

Contents

1 Important Notice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

2 Getting Started. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

3 Terms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

4 Getting to Know the Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

5 Accessory Interface Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

6 Installing the Software and Setting up the Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

7 Initialization and Configuration Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

8 Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

9 Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

10 References. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

11 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Important Notice

KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015

Freescale Semiconductor, Inc. 3

1 Important Notice

Freescale provides the enclosed product(s) under the following conditions:

This evaluation kit is intended for use of ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES

ONLY. It is provided as a sample IC pre-soldered to a printed circuit board to make it easier to access inputs,

outputs, and supply terminals. This evaluation kit may be used with any development system or other source

of I/O signals by simply connecting it to the host MCU or computer board via off-the-shelf cables. Final device

in an application will be heavily dependent on proper printed circuit board layout and heat sinking design as

well as attention to supply filtering, transient suppression, and I/O signal quality.

The goods provided may not be complete in terms of required design, marketing, and or manufacturing related

protective considerations, including product safety measures typically found in the end product incorporating

the goods. Due to the open construction of the product, it is the user's responsibility to take any and all

appropriate precautions with regard to electrostatic discharge. In order to minimize risks associated with the

customers applications, adequate design and operating safeguards must be provided by the customer to

minimize inherent or procedural hazards. For any safety concerns, contact Freescale sales and technical

support services.

Should this evaluation kit not meet the specifications indicated in the kit, it may be returned within 30 days from

the date of delivery and will be replaced by a new kit.

Freescale reserves the right to make changes without further notice to any products herein. Freescale makes

no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor

does Freescale assume any liability arising out of the application or use of any product or circuit, and

specifically disclaims any and all liability, including without limitation consequential or incidental damages.

“Typical” parameters can and do vary in different applications and actual performance may vary over time. All

operating parameters, including “Typical”, must be validated for each customer application by customer’s

technical experts.

Freescale does not convey any license under its patent rights nor the rights of others. Freescale products are

not designed, intended, or authorized for use as components in systems intended for surgical implant into the

body, or other applications intended to support or sustain life, or for any other application in which the failure

of the Freescale product could create a situation where personal injury or death may occur.

Should the Buyer purchase or use Freescale products for any such unintended or unauthorized application,

the Buyer shall indemnify and hold Freescale and its officers, employees, subsidiaries, affiliates, and

distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising

out of, directly or indirectly, any claim of personal injury or death associated with such unintended or

unauthorized use, even if such claim alleges that Freescale was negligent regarding the design or manufacture

of the part. Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other

product or service names are the property of their respective owners. © Freescale Semiconductor, Inc. 2015

Getting Started

KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015

4 Freescale Semiconductor, Inc.

2 Getting Started

2.1 Kit Contents/Packing List

The KIT34FS6407EVB and KIT34FS6408EVB contents include:

• Assembled and tested evaluation board/module in anti-static bag

• Warranty card

2.2 Jump Start

Freescale’s analog product development boards help to easily evaluate Freescale products. These tools support analog mixed signal and

power solutions including monolithic ICs using proven high-volume SMARTMOS mixed signal technology, and system-in-package devices

utilizing power, SMARTMOS and MCU dies. Freescale products enable longer battery life, smaller form factor, component count reduction,

ease of design, lower system cost and improved performance in powering state of the art systems.

• Click on the appropriate link for your board

KIT34FS6407EVB: www.freescale.com/KIT34FS6407EVB

KIT34FS6408EVB: www.freescale.com/KIT34FS6408EVB

• Review your Tool Summary Page

• Look for

• Download documents, software, and other information

Once the files are downloaded, review the user guide in the bundle. Jump start bundles are available on each tool summary page with the

most relevant and current information. The information includes everything needed for design.

2.3 Required Equipment and Software

To use this kit, you need

•2.7 V to 40 V power supply, 3.0 A capability

• Freescale’s KITUSBSPIDGLVME interface dongle

• SPIGen Graphical User Interface or MC3390X_GUI

When not connected to an evaluation board, the KITUSBSPIDGLVME can be used in standalone mode to program its

onboard MC68HC908JW32 microcontroller. In this case, the interface dongle and USB cable are required. For more

information, see the “

SPIGen 7 User Guide”.

2.4 System Requirements

The kit requires the following:

• USB-enabled PC with Windows

XP or higher

Jump Start Your Design

Terms

KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015

Freescale Semiconductor, Inc. 5

3Terms

Part Number or

Parameter

Definition

CAN_5V 5.0 V CAN voltage

EVB Evaluation Board

FCCU Fault Collection and Control Unit

FS0B Fail-safe Output Number 0

INTB Interrupt

IO Input/Output

LDO Low-dropout Regulator

RSTB Reset

SMPS Switching Mode Power Supply

SPIGen Software utility (installed on a PC) provides communication functions between the PC and a Freescale evaluation board

AUX

Auxiliary power supply

CCA

Power supply for ADC

PRE

Pre-regulator voltage

WD Watchdog

Getting to Know the Hardware

KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015

6 Freescale Semiconductor, Inc.

4 Getting to Know the Hardware

4.1 Board Overview

KIT34FS6407EVB and KIT34FS6408EVB evaluation boards demonstrate the functionality of the SMARTMOS MC34FS6407 and

MC34FS6408 power system basis chips, respectively. These ICs are equipped with an intelligent power management system including

safety features targeting the latest ISO26262 automotive functional safety standard. The EVB is a standalone board that can be used

either with a compatible microcontroller or with a PC. The latter case requires a KITUSBSPIDGLEVME accessory interface board. See

Section 2.3 "Required Equipment and Software".

4.2 Board Features

This EVB comes mounted with either an MC34FS6407 or an MC34FS6408 IC. The main features of the board are:

•V

BAT

power supply either through power jack (2.0 mm) or phoenix connector

•V

CORE

configuration:1.2 V or 3.3 V

•V

CCA

configuration: 5.0 V/3.3 V

• Internal transistor or external PNP

•V

AUX

configuration: 3.3 V or 5.0 V

• Enabled or disabled at startup

• Ignition key switch

• CAN bus

• IO connector (IO_0 to IO_5)

• Debug connector (SPI bus, CAN digital, RSTB, FS0B, INTB, Debug, MUX_OUT)

• Signalling LED to give state of signals or regulators

4.3 Device Features

The MC34FS6407 and the MC34FS6408 are multi-output ICs, with power supply and HSCAN transceiver. The MC34FS6407 is designed

to support up 800 mA on V

CORE

, while MC34FS6408 supports up to 1.5 A on V

CORE

. All other features are the same.

Table 1. Device Features

Device Description Features

MC34FS6407/

MC34FS6408

Power system

basis chip with

high-speed CAN

and LIN

transceivers

• Highly flexible SMPS pre-regulator, allowing two topologies: non-inverting buck-boost or

standard buck

• Switching mode power supply (SMPS) dedicated to MCU core supply: 1.2 V or 3.3 V,

delivering up to 1.5 A for the MC34FS6408 and up to 800 mA for the MC34FS6407

• Linear voltage regulator dedicated to MCU A/D reference voltage or I/Os supply (VCCA):

5.0 V or 3.3 V

• Linear voltage regulator dedicated to auxiliary functions or to a sensor supply (VCCA

tracker or independent 5.0 V/3.3 V)

• Multiple wake-up sources in Low-power mode: CAN and/or IOs

• Battery voltage sensing and multiplexer output terminal (various signal monitoring)

• Enhanced safety block associated with fail-safe outputs

• Six configurable I/Os

• ISO11898 high-speed CAN interface compatibility for baud rates of 40 kB/s to 1.0 MB/s

• High EMC immunity and ESD robustness

Getting to Know the Hardware

KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015

Freescale Semiconductor, Inc. 7

4.4 Board Description

The EVB comes with either a Freescale MC34FS6407or MC34FS6408 IC mounted on it. Below is a view of the board indicating the major

components.

Figure 2. Board Description —MC34FS6407and MC34FS6408

Table 2. Board Description

Name Description

Buck/Buck-Boost Section

•V

PRE

DC/DC selection mode, either Boost or Buck

Battery Connection

• Battery voltage input, either on Jack (black connector) or Phoenix (green) connector

Main Switch

• Battery voltage ON/OFF

Power Supplies

Buck/Buck Boost

Section

LEDs for

Power

Supplies

Compensation

Network

CORE

Selection

DBG Mode

Select

SPI Dongle

Connector

Battery

Connection

Main

Switch

Ignition

Key

Switch

LIN Bus

(Not Avaiable on

KIT34FS640xEVB)

CAN Bus

FS Output

Circuitry

CCA

and V

AUX

Selection

Main Signals of

MC34FS6407/MC34FS6406

Second Resistor Bridge

- V

DRIFG

Selection

I/Os of

MC34FS6407/MC34FS6406

Getting to Know the Hardware

KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015

8 Freescale Semiconductor, Inc.

4.5 Evaluation Board Configuration

Figure 3 shows a configuration example for the EVB, which enables:

•V

CORE

3.3 V

• Compensation network for MPC5643L

•V

CCA

and V

AUX

= 5.0 V

•V

CCA

with external PNP

• Debug mode

•V

PRE

in Buck mode

•V

DDIO

tied to V

CCA

• Various signalling LEDs enabled

• IO1 configured as IN/OUT

Ignition Key Switch

• Simulate ignition key. Connected to IO_0

LIN Bus

• LIN bus as a master (Not available on KIT34FS640xEVB)

CAN Bus

• CANH and CANL differential pair

I/Os of MC34FS6407_8

• All IOs, VDDIO and GND available

Second Resistor Bridge - V

DRIFT

Selection

• Bridge resistor for V

CORE

redundant check

Main Signals of MC34FS6407_8

• SPI, VDDIO, fail-safe pin, CAN, MUXOUT, INTB and RSTB available

CCA

and V

AUX

Selection

•V

CCA

and V

AUX

voltage selection

FS Output Circuitry

• FS0B configuration

SPI Dongle Connector

• Connector with SPI bus. Compliant to SPIGen Freescale board

DBG Mode Select

• Controls Debug or Normal mode entering at boot up

CORE

Selection

•V

CORE

voltage selection

Compensation Network

• Compensation network selection

LEDs for Power Supplies

• Switches for ON/OFF on LEDs

Power Supplies

• MC34FS6407 or MC34FS6408 output power supply (V

PRE

, V

CORE

, V

AUX

, V

CCA

)

Table 2. Board Description (continued)

Name Description

Getting to Know the Hardware

KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015

Freescale Semiconductor, Inc. 9

Figure 3. Default Board Configuration

KIT34FS640XEVB REV A

2015 FREESCALE

Switch Jumper Red LED Green LED

Getting to Know the Hardware

KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015

10 Freescale Semiconductor, Inc.

4.6 LED Definitions

The following table lists the LEDs used as visual output devices on the EVB:

4.7 Test Point Definitions

The following test-point jumpers provide access to signals on the MC34FS6407or MC34FS6408:

Table 3. LEDs

Schematic

Label

Name Description

D6 V

PRE

Indicator of pre-regulator voltage

D7 V

AUX

Indicator of auxiliary power supply

D8 V

CCA

Indicator of ADC power supply

D9 CAN_5V Indicator of 5.0 V CAN voltage

D10 IO_5 Indicator of IO_5 state

D11 IO_4 Indicator of IO_4 state

D12 FS0B Indicator for fail-safe output number 0

D13 V

BAT_P

Indicator of battery voltage after protection diode

D14 RSTB Indicator of a reset

D15 INTB Indicator of an interrupt

D17 V

CORE

Indicator of V

CORE

power supply

Table 4. Test Points

Schematic Label Signal Name Description

TP2 J24.3 -

TP3 J24.5 -

TP4 J24.7 -

TP5 J20.16 -

TP6 PGND Power ground

TP7 PGND Power ground

TP8 GND Ground

TP9 GND Ground

TP10 GND Ground

TP11 GND Ground

TP12 GND Ground

TP13 GND Ground

TP14 GND Ground

TP15 GND Ground

Getting to Know the Hardware

KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015

Freescale Semiconductor, Inc. 11

TP16 GND Ground

TP17 GND Ground

TP18 J24.2 -

TP19 J24.4 -

TP20 J24.6 -

TP21 J24.8 -

TP22 J24.10 -

TP23 J24.12 -

TP24 J24.14 -

TP25 J24.16 -

TP26 V

PRE

Pre-regulator voltage

TP27 V

CORE

Core voltage for the MCU

TP28 CANH -

TP29 CANL -

TP30 LIN LIN bus (Not available on

KIT34FS640xEVB)

TP31 MUX_OUT Output from the analog multiplexer

TP32 FS0B Fail-safe output

TP33 RSTB Reset signal

TP34 INTB Interrupt output

TP35 V

PRE

Switching voltage

TP36 V

AUX

Auxiliary power supply

TP37 V

CCA

ADC power supply

TP38 CAN_5V CAN power supply

TP39 V

SUP3

Supply voltage

TP40 VSW_Core V

CORE

supply voltage

Table 4. Test Points (continued)

Schematic Label Signal Name Description

Getting to Know the Hardware

KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015

12 Freescale Semiconductor, Inc.

4.8 Connector and Jumper Definitions

Table 5. Main Power Supply Connector

JP1 Pin Number Name of Power Rail Description

CORE

Core voltage for the MCU

2 PGND Power ground

CCA

ADC power supply

4 GND Ground

AUX

Auxiliary power supply

6 GND Ground

7 CAN_5V CAN power supply

8 GND Ground

PRE

Pre-regulator voltage

10 PGND Power ground

Table 6. Jumpers J1 through J31 (Including Connectors)

Schematic

Label

Pin Number Pin Name Jumper/Pin Function

Compensation network for FB_core – part 1

1-2 V

CORE

= 1.23 V

3-4 V

CORE

= 3.3 V

C_OUT – selection of output capacitance for V

CORE

If connected, output capacitance is 40 µF, 20 µF otherwise

No jumper C

OUT

= 20 µF

1-2 C

OUT

= 40 µF

Power supply DC 12 V

Buck-boost/standard buck mode configuration

1-2

Buck-boost configuration

3-4

No jumper

Buck only configuration

CORE

selection

1-2

CORE

= 1.23 V

3-4

CORE

= 3.3 V

Getting to Know the Hardware

KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015

Freescale Semiconductor, Inc. 13

Configuration for Boots_core pin

1-2

Boots_core pin connected to GND – used for devices with linear voltage regulator on

CORE

2-3

Boots_core pin connected to SW_core – used for devices with switching mode power

supply on V

CORE

Power supply (max. voltage = 40 V)

This connector should be used to supply EVB from protected voltage source

1 VBAT

Positive supply

2GND

Ground

Power supply for EVB

Allows disconnecting of all three supply pins for current measurements

Normally (no measurement), jumpers should be connected

1-2

Enables power supply (V

BAT_P

) for VSUP3 pin of MC34FS6407(or MC34FS6408)

3-4

Enables power supply (V

SUP

) for VSUP1 and VSUP2 pins of MC34FS6407(or

MC34FS6408)

Compensation network for FB_core – part 2

1-2

CORE

= 1.23 V

3-4

CORE

= 3.3 V

J10

SNS

_EN – connects battery voltage before filter to V

SENSE

J11

External transistor for V

CCA

1-2

Emitter of Q2 connected to VCCA_E

2-3

External transistor Q2 is not used

J12

IO_0_PD – pulls down IO_0

J13

FS0B pull-up connection

1-2

FS0B pull-up is supplied from V

SUP3

2-3

FS0B pull-up is supplied from V

DDIO

J14

Connects base of the transistor Q2 to the VCCA_B pin

J15

External resistor bridge monitoring (for future use)

Used in conjunction with J18

Resistor bridge has to be in same configuration as J5

Voltage on this voltage divider has to be adjusted to same level as for first bridge using potentiometer R17

1-2

CORE

= 1.23 V

3-4

CORE

= 3.3 V

Table 6. Jumpers J1 through J31 (Including Connectors) (continued)

Schematic

Label

Pin Number Pin Name Jumper/Pin Function

Getting to Know the Hardware

KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015

14 Freescale Semiconductor, Inc.

J16

DDIO

tracking

1-2

DDIO

tracks V

CCA

2-3

DDIO

tracks V

CORE

J17

DBG_EN - enables debug mode

No jumper

Normal mode

1-2

Debug mode

J18

DRIFT_MONIT – External resistor bridge monitoring

1-2

Second resistor bridge on IO_1 is disabled

2-3

Reserved for future use

J19

CCA

AUX

regulator selection

1-3 and 2-4

AUX

is disabled

3-5 and 4-6

AUX

is enabled

Table 6. Jumpers J1 through J31 (Including Connectors) (continued)

Schematic

Label

Pin Number Pin Name Jumper/Pin Function

Getting to Know the Hardware

KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015

Freescale Semiconductor, Inc. 15

J20

Additional Inputs/Output

1FS0B

Fail-safe output

2 VDDIO

DDIO

voltage

3MISO

SPI – Master Input Slave Output

4RSTB

Reset pin – connect to the reset line of the MCU

5MOSI

SPI – Master Output Slave Input

6GND

Ground

7SCLK

SPI – clock

8GND

Ground

9NCS

SPI – Chip Select

10 GND

Ground

11 MUX_OUT

Output from the multiplexer – connect to the MCU's ADC

12 INTB

Interrupt pin – connect to the MCU IO with an interrupt capability

13 RXD_L

LIN receive pin – connect to the MCU — Not Available on KIT34FS640xEVB

14 TXD_L

LIN transmit pin – connect to the MCU — Not Available on KIT34FS640xEVB

15 GND

Ground

16 TP5

17 RXD

CAN receive pin – connect to the MCU

18 TXD

CAN transmit pin – connect to the MCU

19 DBG

Debug pin

20 GND

Ground

J21

LIN connector

1LIN

LIN after transceiver (NOT the MCU side) — Not Available on KIT34FS640xEVB

2GND

Ground

J22

CAN connector

1CANH

CANH signal after transceiver (NOT the MCU side)

2CANL

CANL signal after transceiver (NOT the MCU side)

Table 6. Jumpers J1 through J31 (Including Connectors) (continued)

Schematic

Label

Pin Number Pin Name Jumper/Pin Function

Getting to Know the Hardware

KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015

16 Freescale Semiconductor, Inc.

J23

General Inputs/Outputs

pin1 IO_1

pin2 IO_0

pin3 IO_3

pin4 IO_2

pin5 IO_5

pin6 IO_4

pin7 VDDIO

pin8 NC

pin9 VBAT

pin10 GND

J24

SPI/USB dongle or MCU connection

SPI/USB dongle should be directly connected to this port

pin1 GND

Ground

pin2 TP18

pin3 TP2

pin4 TP19

pin5 TP3

pin6 TP20

pin7 TP4

pin8 TP21

pin9 SCLK

SPI – clock

pin10 TP22

Not connected

pin11 MOSI

SPI – Master Output Slave Input

pin12 TP23

pin13 MISO

SPI – Master Input Slave Output

pin14 TP24

pin15 NCS

SPI – Chip Select

pin16 TP25

J25

Power supply for LEDs on IO_4 and IO_5 (D11, D10)

1-2

Enables power supply for IO_4 (D11)

3-4

Enables power supply for IO_5 (D10)

J26

RSTB_LED_EN – enables LED D14 for RSTB output

Table 6. Jumpers J1 through J31 (Including Connectors) (continued)

Schematic

Label

Pin Number Pin Name Jumper/Pin Function

Getting to Know the Hardware

KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015

Freescale Semiconductor, Inc. 17

J27

INTB_LED_EN – enables LED D15 for INTB output

J28

IO5_OUT – IO_5 output configuration

1-2

IO_5 connected to LED D10 via transistor Q5

2-3

IO_5 pulled down

J29

IO4_OUT – IO_4 output configuration

1-2

IO_4 pulled down

2-3

IO_4 connected to LED D11 via transistor Q6

J30

Enable LED D12 for fail-safe.

J31

Enables LED D13 as indicator of power supply

J32

Enables LED D17 as indicator for V

CORE

power supply

Table 6. Jumpers J1 through J31 (Including Connectors) (continued)

Schematic

Label

Pin Number Pin Name Jumper/Pin Function

Getting to Know the Hardware

KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015

18 Freescale Semiconductor, Inc.

4.8.1 Compensation Network

A voltage regulator needs feedback from the V

CORE

voltage to be able to adjust (control) output voltage. For this reason, two bridges are

implemented in the external MC34FS6407 or MC34FS6408 circuitry. Static feedback (steady-state) voltage is defined by a simple resistor

bridge (given by RA3/RB3 and RA4). Dynamic behavior of the regulator is controlled by another bridge that is an RC divider (defined by

RBx, CBx, R1, C1, R2, C2).

Figure 4 shows the compensation network. Steady-state voltage can be either 1.2 V or 3.3 V. To tune the

dynamic performance, the board is equipped with two different bridges (possible combinations of the jumpers J1 and J9 are shown in

Table 7). The combinations shown in Table 7 are chosen to provide optimal performance for the given output voltage. The real dynamic

performance can differ for different applications and can be tuned by changing the compensation network and by adding output capacitors

(J2).

Figure 4. Compensation Network and V

CORE

Setup Schematic

Table 7. Compensation Network and V

CORE

Settings

CORE

(V)

Jumper Settings

Static Behavior Dynamic Behavior

J5 J1 J9

1.23 3-4 3-4 3-4

3.3 1-2 1-2 1-2

CORE

_sense

Getting to Know the Hardware

KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015

Freescale Semiconductor, Inc. 19

4.8.2 Second Resistor Bridge - V

DRIFT

Monitoring

To increase the safety level of an application, a second resistor bridge has been added. This bridge generates the same voltage as the

bridge connected to FB_core pin. If the difference between voltages is greater than V

DRIFT

, the FS state machine is impacted.

Invoking this functionality involves both the board hardware and the software configuration. On the hardware side, the second resistor

bridge must be configured by jumper J18, as shown in the Figure 5, and adjusted by the potentiometer R17 to set the same voltage as on

the first bridge. Software sets registers INIT_Vreg1 (bit Vcore_FB to 1) and register INIT_FSSM1 (bit IO_1_FS to 1).

Figure 5. Second Resistor Bridge

Table 8. V

DRIFT

Monitoring Settings

CORE

(V)

Hardware Settings

J15 J18

1.23 1+2 3+4

3.3 3+4 1+2

CORE

J15

IO _ 1 V

CORE

FB Drift Enable

Getting to Know the Hardware

KT34FS6407-34FS6408UG User’s Guide Rev. 1.0 8/2015

20 Freescale Semiconductor, Inc.

4.9 Switch Definitions

Table 9. Switches

Switch Number Position Function Description

SW1

Power supply select

1-2

Supply from J7 selected

2-3

Power jack on J3 selected

SW2

CCA

AUX

switch

Only one choice is possible at the same time

3.3 V / 3.3 V

5.0 V / 5.0 V

3.3 V / 5.0 V This setting is not allowed if V

AUX

is not used - option

CCA

only (selected by J19)

5.0 V / 3.3 V

SW3

LEDs - indicators for power supplies

PRE

Enables LED indicator for pre-regulator

AUX

Enables LED indicator for auxiliary power supply

CCA

Enables LED indicator for V

CCA

regulator

CAN_5 V Enables LED indicator for CAN regulator

SW4

Ignition switch

1-2

IO_0 connected to V

BAT

(ignition key active)

2-3

No voltage on the IO_0

Page is loading ...

NXP KIT34FS6407EVB User guide

Brand: NXP

Model: KIT34FS6407EVB

Type: User guide

This manual is also suitable for

KIT34FS6408EVB

Download PDF

report

NXP KIT34FS6407EVB User guide

This manual is also suitable for

NXP KIT34FS6407EVB User guide

Related papers

Other documents