Curtain Conversion Kit #A39843-001
For Scotsman Models:
•
EH222
•
C0830/C1030
•
C1448/C1848/C2148 - need two kits each
Kit contents:
•
Upper and Lower Curtain with magnets
•
Curtain switch (for EH222 only)
•
Curtain switch mounting bracket (for EH222 only).
• Loop clamps
• Screws
Tools required:
• Screw driver
EH222 - 1 kit per unit
1. Remove front panel.
2. Shut machine down.
3. Remove evaporator cover.
4. Remove top panel
5. Remove left side panel.
6. Swing controller box out.
7. Open controller door.
8. Remove curtain.
9. Install switch mounting bracket from kit in location in illustration.
10. Attach switch and bracket to wall of ice machine using screws provided.
Instructions
11. Route wire thru 2 loop clamps, wrap once around each clamp: one about 2 - 3"
from switch and the other 8 – 10” up from switch.
12. Route switch wire up right edge of freezing compartment, over back wall next to ice
thickness sensor wire, to the left part of the cabinet.
13. Remove cover from wire chase and route wire into back of controller box. Be sure
wire is routed away from ice making area.
14. Disconnect existing curtain switch and connect the new one in its place. Leave
original switch wire loose in control box.
15. Remove slack from wires. Secure loop clamps to side of freezing compartment
using provided screws.
A
Loop Clamps
Wire Routing
Switch and
Bracket Detail,
locate bracket
against right
inside corner of
compartment
Switch and
Bracket
Wire Routing
16. Mount new curtain assembly in ice machine.
17. Move curtain in and out and confirm curtain switch light works properly. Be sure
curtain switch wire is not in the way of curtain movement.
•
Note: Curtain switch mounts to the RIGHT of the curtain.
18. Check that any sealant or gaskets have been trimmed to remove any interference
with the curtain.
19. Reinstall all panels and restart unit.
C0830/C1030 - uses 1 kit
C1448/C1848/C2148 – requires 2 kits per unit
•
Remove front panel.
•
Shut unit off.
•
Remove evaporator cover.
•
Remove existing curtain(s).
•
Disconnect curtain switch from existing mounting.
•
Install curtain switch in new location.
•
Attach curtain switch to new location using two #6 screws from kit.
•
Secure wire to refrigerant tube as shown.
•
Repeat for opposite side on two evaporator models.
•
Mount new curtain assemblies in ice machine.
•
Move curtain(s) in and out and confirm curtain switch light works properly.
•
Reinstall all panels and restart unit.
17-3346-01
Curtain Switch in New Location
Magnet
-
1
-
2
-
3
-
4
Scotsman Prodigy Articulated Curtain Kit for all 18" evaps. - A39843-001 - 17-3346-01 Operating instructions
- Type
- Operating instructions
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Scotsman Two Piece Articulated Curtain - 17-3362-01 Operating instructions
-
-
-
Scotsman C1448R User manual
-
-
-
-
-
-
Other documents
-
Scotsman Ice C1848 User manual
-
-
-
Manitowoc Ice Q Model QuietQube Q0600C/Q0800C/Q1000C Installation guide
-
Ventrac SS300 Owner's manual
-
Manitowoc S-2070C Specification
-
-
Manitowoc IB1000C User manual
-
-