Generac 20 kW 0053371 User manual

STANDBY GENERATOR

OWNER'S MANUAL

This manual should remain with the unit.

A new standard of reliability

Serial Number

1.6L

20kW

Models: 005336-1

005337-1

—CAUTION—

ONLY QUALIFIED ELECTRICIANS OR CONTRACTORS SHOULD ATTEMPT INSTALLATION!

DEADLY EXHAUST FUMES. OUTDOOR INSTALLATION ONLY!



Not intended for use in critical life support applications.



Cover079A Rev. 0 08/06 Part No. 0G2966A

Standby Generator Sets

Table of Contents

SECTION PAGE

SAFETY RULES ................................................ 1-1

INTRODUCTION .....................................................1-3

Read this Manual Thoroughly ...................................1-3

Operation and Maintenance ......................................1-3

How to Obtain Service ..............................................1-3

IDENTIFICATION RECORD .....................................2-1

Data Label ................................................................2-1

EQUIPMENT DESCRIPTION ...................................3-1

Equipment Description ................................................3-1

Engine Oil Recommendations ......................................3-1

Coolant Recommendations...........................................3-1

ENGINE PROTECTIVE DEVICES ............................4-1

High Coolant Temperature Switch ............................4-1

Low Coolant Level Sensor .........................................4-1

Low Oil Pressure Switch ...........................................4-1

Overcrank Shutdown ................................................4-1

Overspeed Shutdown ................................................4-1

RPM Sensor Loss Shutdown .....................................4-1

DC Fuse ....................................................................4-1

FUEL SYSTEMS .....................................................5-1

Fuel Requirements ....................................................5-1

Natural Gas Fuel System ..........................................5-1

Propane Vapor Withdrawal Fuel System....................5-1

LP Fuel System .........................................................5-1

SPECIFICATIONS ...................................................6-1

Generator .................................................................6-1

Engine.......................................................................6-1

Cooling System .........................................................6-1

Fuel System ..............................................................6-1

Electrical System ......................................................6-1

Cold Weather Kit .......................................................6-2

Reconfiguring the Fuel System ..................................6-2

GENERAL INFORMATION .......................................7-1

Generator AC Lead Connections ..................................7-1

Four-lead, Single-phase Stator ..................................7-1

Alternator Power Winding Connections ........................7-1

3-phase Alternators ..................................................7-1

INSTALLATION .......................................................8-1

Installation ...................................................................8-1

Preparation Before Start-up .........................................8-1

Transfer Switch ........................................................8-1

Fuel System ..............................................................8-1

Generator Set Lubrication ........................................8-1

Prior to Initial Start-up .............................................8-1

Engine Coolant .........................................................8-1

Belt Tension ..............................................................8-1

Electrical System ......................................................8-1

Initial Inspection for QT Genset Start-up .....................8-1

Start-up Checklist ........................................................8-2

Preparation for Start-up............................................8-2

Start-up Inspection ...................................................8-2

OPERATION ...........................................................9-1

Generator Control and Operation ................................9-1

Operating Unit with Manual Transfer Switch ...............9-1

Engine Start-up and Transfer ...................................9-1

Retransfer and Shutdown .........................................9-1

Operating Unit with Automatic Transfer Switch ...........9-1

MAINTENANCE .....................................................10-1

Maintenance Performed by Authorized

Service Facilities .....................................................10-1

Every Three Months ...............................................10-1

Once Every Six Months ...........................................10-1

Once Annually .........................................................10-1

First 100 Operating Hours ......................................10-1

Every 500 Operating Hours ....................................10-1

Every 800 Operating Hours ....................................10-1

Exhaust Manifold Procedure ......................................10-1

Intake Manifold Procedure .........................................10-1

Cylinder Head Procedure ...........................................10-1

Cooling System ..........................................................10-2

Overload Protection for Engine DC

Electrical System ....................................................10-2

Checking Fluid Levels ................................................10-2

Check Engine Oil ....................................................10-2

Battery Fluid ...........................................................10-2

Engine Coolant .......................................................10-2

Maintenance Owner/Operator Can Perform ................10-3

Check Engine Oil Level ...........................................10-3

Check Battery .........................................................10-3

Exercise System ......................................................10-3

Inspect Cooling System ...........................................10-3

Check Engine Coolant Level....................................10-3

Perform Visual Inspection .......................................10-3

Inspect Exhaust System ..........................................10-3

Check Fan Belt ........................................................10-3

Inspect Engine Governor ........................................10-3

Changing Engine Oil ...............................................10-3

Changing the Engine Air Cleaner ............................10-3

Spark Plugs ............................................................10-4

Coolant Change .......................................................10-4

Miscellaneous Maintenance ........................................10-4

Cleaning the Generator ...........................................10-4

Battery ....................................................................10-4

Battery Maintenance ...............................................10-4

Battery Replacement ...............................................10-5

SERVICE SCHEDULE ...........................................11-1

TROUBLESHOOTING ...........................................12-1

Troubleshooting Guide ...............................................12-1

NOTES

EXPLODED VIEWS & PARTS LISTS

WIRING DIAGRAMS & SCHEMATICS

WARRANTY

Content004 Rev. 0 09/05

1-1

INTRODUCTION

Thank you for purchasing this model of the Stationary Emergency

Generator set product line.

Every effort was expended to make sure that the information and

instructions in this manual were both accurate and current at the

time the manual was written. However, the manufacturer reserves

the right to change, alter or otherwise improve this product(s) at

any time without prior notice.

READ THIS MANUAL THOROUGHLY 

If any portion of this manual is not understood, contact the near-

est Authorized Service Dealer for starting, operating and servicing

procedures.

Throughout this publication, and on tags and decals affixed to the

generator, DANGER, WARNING, CAUTION and NOTE blocks are

used to alert personnel to special instructions about a particular

service or operation that may be hazardous if performed incor-

rectly or carelessly. Observe them carefully. Their definitions are

as follows:

DANGER

After this heading, read instructions that, if not

strictly complied with, will result in serious per-

sonal injury, including death, or property damage.

After this heading, read instructions that, if not

strictly complied with, may result in personal

injury or property damage.

After this heading, read instructions that, if not

strictly complied with, could result in damage to

equipment and/or property.

NOTE:

After this heading, read explanatory statements that require

special emphasis.

These safety warnings cannot eliminate the hazards that they

indicate. Common sense and strict compliance with the special

instructions while performing the service are essential to prevent-

ing accidents.

Four commonly used safety symbols accompany the DANGER,

WARNING and CAUTION blocks. The type of information each

indicates is as follows:



This symbol points out important safety informa-

tion that, if not followed, could endanger per-

sonal safety and/or property of others.



This symbol points out potential explosion

hazard.



This symbol points out potential fire hazard.



This symbol points out potential electrical shock

hazard.

The operator is responsible for proper and safe use of the equip-

ment. The manufacturer strongly recommends that the operator

read this Owner's Manual and thoroughly understand all instruc-

tions before using this equipment. The manufacturer also strongly

recommends instructing other users to properly start and operate

the unit. This prepares them if they need to operate the equipment

in an emergency.

OPERATION AND MAINTENANCE 

It is the operator's responsibility to perform all safety checks, to

make sure that all maintenance for safe operation is performed

promptly, and to have the equipment checked periodically by

an Authorized Service Dealer. Normal maintenance service and

replacement of parts are the responsibility of the owner/operator

and, as such, are not considered defects in materials or workman-

ship within the terms of the warranty. Individual operating habits

and usage contribute to the need for maintenance service.

Proper maintenance and care of the generator ensure a minimum

number of problems and keep operating expenses at a minimum.

See an Authorized Service Dealer for service aids and accessories.

Operating instructions presented in this manual assume that the

generator electric system has been installed by an Authorized

Service Dealer or other competent, qualified contractor. Installation

of this equipment is not a “do-it-yourself” project.

HOW TO OBTAIN SERVICE 

When the generator requires servicing or repairs, simply contact

an Authorized Service Dealer for assistance. Service technicians

are factory-trained and are capable of handling all service needs.

When contacting a dealer about parts and service, always supply

the complete Model Number, Serial Number and Type Code (where

applicable) from the DATA LABEL that is affixed to the unit.

AUTHORIZED SERVICE DEALER LOCATION

To locate the nearest AUTHORIZED

SERVICE DEALER, please call this number:

1-800-333-1322

or locate us on the web at:

www.generac.com

Stationary Emergency Generator

Important Safety Instructions

Safety 001 Rev. C 08/09

Study these SAFETY RULES carefully before installing, operating

or servicing this equipment. Become familiar with this Owner’s

Manual and with the unit. The generator can operate safely, effi-

ciently and reliably only if it is properly installed, operated and

maintained. Many accidents are caused by failing to follow simple

and fundamental rules or precautions.

The manufacturer cannot anticipate every possible circumstance

that might involve a hazard. The warnings in this manual, and on

tags and decals affixed to the unit are, therefore, not all inclusive.

If a procedure, work method or operating technique is used that

the manufacturer does not specifically recommend, ensure that it

is safe for others. Also make sure the procedure, work method or

operating technique utilized does not render the generator unsafe.

DANGER



Despite the safe design of this generator,

operating this equipment imprudently, neglect-

ing its maintenance or being careless can cause

possible injury or death. Permit only responsible

and capable persons to install, operate or main-

tain this equipment.



Potentially lethal voltages are generated by

these machines. Ensure all steps are taken to

render the machine safe before attempting to

work on the generator.



Parts of the generator are rotating and/or hot

during operation. Exercise care near running

generators.



GENERAL HAZARDS



For safety reasons, the manufacturer recommends that this •

equipment be installed, serviced and repaired by an Authorized

Service Dealer or other competent, qualified electrician or instal-

lation technician who is familiar with applicable codes, standards

and regulations. The operator also must comply with all such

codes, standards and regulations.

Installation, operation, servicing and repair of this (and related) •

equipment must always comply with applicable codes, stan-

dards, laws and regulations. Adhere strictly to local, state and

national electrical and building codes. Comply with regulations

the Occupational Safety and Health Administration (OSHA) has

established. Also, ensure that the generator is installed, operat-

ed and serviced in accordance with the manufacturer’s instruc-

tions and recommendations. Following installation, do nothing

that might render the unit unsafe or in noncompliance with the

aforementioned codes, standards, laws and regulations.

The engine exhaust fumes contain carbon monoxide gas, which •

can be DEADLY. This dangerous gas, if breathed in sufficient

concentrations, can cause unconsciousness or even death. For

that reason, adequate ventilation must be provided. This should

be considered prior to installing the generator. The unit should

be positioned to direct exhaust gasses safely away from any

building where people, animals, etc., will not be harmed. Any

exhaust stacks that ship loose with the unit must be installed

properly per the manufacturer's instruction, and in strict compli-

ance with applicable codes and standards.

Keep hands, feet, clothing, etc., away from drive belts, fans, •

and other moving or hot parts. Never remove any drive belt or

fan guard while the unit is operating.

Adequate, unobstructed flow of cooling and ventilating air is •

critical in any room or building housing the generator to prevent

buildup of explosive gases and to ensure correct generator

operation. Do not alter the installation or permit even partial

blockage of ventilation provisions, as this can seriously affect

safe operation of the generator.

Keep the area around the generator clean and uncluttered. •

Remove any materials that could become hazardous.

When working on this equipment, remain alert at all times. •

Never work on the equipment when physically or mentally

fatigued.

Inspect the generator regularly, and promptly repair or replace •

all worn, damaged or defective parts using only factory-

approved parts.

Before performing any maintenance on the generator, discon-•

nect its battery cables to prevent accidental start-up. Disconnect

the cable from the battery post indicated by a NEGATIVE, NEG

or (–) first. Reconnect that cable last.

Never use the generator or any of its parts as a step. Stepping •

on the unit can stress and break parts, and may result in dan-

gerous operating conditions from leaking exhaust gases, fuel

leakage, oil leakage, etc.



SAVE THESE INSTRUCTIONS – The manufacturer suggests that these rules for safe operation be copied and posted in

potential hazard areas. Safety should be stressed to all operators, potential operators, and service and repair technicians

for this equipment.

The engine exhaust from this product

contains chemicals known to the state

of California to cause cancer, birth

defects or other reproductive harm.

WARNING:



This product contains or emits chemicals

known to the state of California to cause

cancer, birth defects or other reproductive harm.

WARNING:



1-2

Stationary Emergency Generator

Important Safety Instructions



Safety 001 Rev. C 08/09



ELECTRICAL HAZARDS



All Stationary Emergency Generators covered by this manual •

produce dangerous electrical voltages and can cause fatal

electrical shock. Utility power delivers extremely high and dan-

gerous voltages to the transfer switch as well as the generator.

Avoid contact with bare wires, terminals, connections, etc.,

on the generator as well as the transfer switch, if applicable.

Ensure all appropriate covers, guards and barriers are in place

before operating the generator. If work must be done around

an operating unit, stand on an insulated, dry surface to reduce

shock hazard.

Do not handle any kind of electrical device while stand-•

ing in water, while barefoot, or while hands or feet are wet.

DANGEROUS ELECTRICAL SHOCK MAY RESULT.

If personnel must stand on metal or concrete while installing, •

operating, servicing, adjusting or repairing this equipment,

place insulative mats over a dry wooden platform. Work on the

equipment only while standing on such insulative mats.

The National Electrical Code (NEC) requires the frame and •

external electrically conductive parts of the generator to be con-

nected to an approved earth ground. This grounding will help

prevent dangerous electrical shock that might be caused by a

ground fault condition in the generator or by static electricity.

Never disconnect the ground wire.

Wire gauge sizes of electrical wiring, cables and cord sets must •

be adequate to handle the maximum electrical current (ampac-

ity) to which they will be subjected.

Before installing or servicing this (and related) equipment, make •

sure that all power voltage supplies are positively turned off at

their source. Failure to do so will result in hazardous and pos-

sibly fatal electrical shock.

Connecting this unit to an electrical system normally supplied •

by an electric utility shall be by means of a transfer switch so as

to isolate the generator electric system from the electric utility

distribution system when the generator is operating. Failure to

isolate the two electric system power sources from each other

by such means will result in damage to the generator and may

also result in injury or death to utility power workers due to

backfeed of electrical energy.

Stationary Emergency Generators installed with an automatic •

transfer switch will crank and start automatically when normal

(utility) source voltage is removed or is below an acceptable

preset level. To prevent such automatic start-up and possible

injury to personnel, disable the generator’s automatic start cir-

cuit (battery cables, etc.) before working on or around the unit.

Then, place a “Do Not Operate” tag on the generator control

panel and on the transfer switch.

In case of accident caused by electric shock, immediately •

shut down the source of electrical power. If this is not pos-

sible, attempt to free the victim from the live conductor. AVOID

DIRECT CONTACT WITH THE VICTIM. Use a nonconducting

implement, such as a dry rope or board, to free the victim from

the live conductor. If the victim is unconscious, apply first aid

and get immediate medical help.

Never wear jewelry when working on this equipment. Jewelry •

can conduct electricity resulting in electric shock, or may get

caught in moving components causing injury.



FIRE HAZARDS



Keep a fire extinguisher near the generator at all times. Do NOT •

use any carbon tetra-chloride type extinguisher. Its fumes are

toxic, and the liquid can deteriorate wiring insulation. Keep the

extinguisher properly charged and be familiar with its use. If

there are any questions pertaining to fire extinguishers, consult

the local fire department.



EXPLOSION HAZARDS



Properly ventilate any room or building housing the generator to •

prevent build-up of explosive gas.

Do not smoke around the generator. Wipe up any fuel or oil •

spills immediately. Ensure that no combustible materials are left

in the generator compartment, or on or near the generator, as

FIRE or EXPLOSION may result. Keep the area surrounding the

generator clean and free from debris.

These generators may operate using one of several types •

of fuels. All fuel types are potentially FLAMMABLE and/or

EXPLOSIVE and should be handled with care. Comply with all

laws regulating the storage and handling of fuels. Inspect the

unit’s fuel system frequently and correct any leaks immediately.

Fuel supply lines must be properly installed, purged and leak

tested according to applicable fuel-gas codes before placing

this equipment into service.

Diesel fuels are highly FLAMMABLE. Gaseous fluids such •

as natural gas and liquid propane (LP) gas are extremely

EXPLOSIVE. Natural gas is lighter than air, and LP gas is heavier

than air; install leak detectors accordingly.

1-3

Stationary Emergency Generator

Important Safety Instructions

Safety 001 Rev. C 08/09

IDENTIFICATION RECORD

DATA LABEL 

Every generator set has a DATA LABEL that contains

important information pertinent to the generator. The

data label, which can be found attached to the gen-

erator’s lower connection box, lists the unit’s serial

number and its rated voltage, amps, wattage capac-

ity, phase, frequency, rpm, power factor, production

date, etc.

NOTE:

For actual information related to this particular

model, please refer to the Manual Drawing Listing

located at the end of this manual, or to the data

label affixed to the unit.

Stationary Emergency Generator Model and 

Serial Number

This number is the key to numerous engineering and

manufacturing details pertaining to your unit. Always

supply this number when requesting service, order-

ing parts or seeking information.

2-1

Stationary Emergency Generator

General Information

Identy 002 Rev. C 01/09

WAUKESHA, WI

RATED KW

RATED VOLTAGE

POWER FACTOR

ENGINE RPM

ALTERNATOR SUBTRANSIENT REACTANCE

ALTERNATOR TRANSIENT REACTANCE

CLASS

MODEL

MADE IN USA

PRODUCTION DATE

GENERAC POWER SYSTEMS, INC.

HERTZ

RATED KVA

GENERATOR SET DATA

RATED AMPS

ALT RPM

PHASE

SERIAL

ROTOR STATOR WINDING INSULATION AT 25°C AMBIENT

Data Label

EQUIPMENT DESCRIPTION

This equipment is a revolving field, alternating cur-

rent Stationary Emergency Generator set. It is pow-

ered by a gaseous fueled engine operating at 1800

rpm for 4-pole direct drive units, 3600 rpm for

2-pole direct drive units and 2300 - 3000 rpm for

quiet drive gear units. See the Specifications section

for exact numbers. The unit comes complete with a

sound attenuated enclosure, internally mounted muf-

fler, control console, mainline circuit breaker, battery

charger, and protective alarms as explained in the

following paragraph.

All AC connections, including the power leads from

the alternator, 120 volt battery charger input and

control connections to the transfer switch are avail-

able in the main connection box.

The Stationary Emergency Generator incorporates

the following generator features:

• Rotor and Stator insulation is Class F rated as

defined by NEMA MG1-32.6, NEMA MG1-1.66.

The generator is self ventilated and drip-proof con-

structed.

• The voltage waveform deviation, total harmonic

content of the AC waveform and telephone influ-

ence factor have been evaluated and are acceptable

according to NEMA MG1-32.

ENGINE OIL RECOMMENDATIONS

The unit has been filled with 15W-40 engine oil at

the factory. Use a high-quality detergent oil classi-

fied “For Service SJ or SH.” Detergent oils keep the

engine cleaner and reduce carbon deposits. Use oil

having the following SAE viscosity rating, based on

the ambient temperature range anticipated before the

next oil change:



Any attempt to crank or start the engine before

it has been properly serviced with the recom-

mended oil may result in an engine failure.

NOTE:

For temperatures below 32° F, it is strongly recom-

mended to use the optional Cold Weather Start Kit

(part number listed in the Specification Section).

The oil grade for temperatures below 32° F is 5W-

30 synthetic oil.

COOLANT RECOMMENDATIONS

Use a mixture of half low silicate ethylene glycol

base anti-freeze and deionized water. Cooling system

capacity is listed in the specifications. Use only deion-

ized water and only low silicate anti-freeze. If desired,

add a high quality rust inhibitor to the recommended

coolant mixture. When adding coolant, always add

the recommended 50-50 mixture.



Do not use any chromate base rust inhibitor

with ethylene glycol base anti-freeze or chro-

mium hydroxide (“green slime”) forms and will

cause overheating. Engines that have been oper-

ated with a chromate base rust inhibitor must

be chemically cleaned before adding ethylene

glycol base anti-freeze. Using any high silicate

anti-freeze boosters or additives will also cause

overheating. The manufacturer also recommends

that any soluble oil inhibitor is NOT used for this

equipment.

DANGER



Do not remove the radiator pressure cap while

the engine is hot or serious burns from boiling

liquid or steam could result.



Ethylene glycol base antifreeze is poisonous.

Do not use mouth to siphon coolant from the

radiator, recovery bottle or any container. Wash

hands thoroughly after handling. Never store

used antifreeze in an open container because

animals are attracted to the smell and taste of

antifreeze even though it is poisonous to them.

Temperature Oil Grade (Recommended)

Above 80° F (27° C) SAE 30W or 15W-40

32° to 80° F (0° to 27° C) SAE 20W-20 or 15W-40

Below 32° F (0° C) See Note

3-1

Stationary Emergency Generator

Equipment Description

Equip002 Rev. B 11/08

ENGINE PROTECTIVE DEVICES

The Stationary Emergency Generator may be required

to operate for long periods of time without an opera-

tor on hand to monitor such engine conditions as

coolant temperature, oil pressure or rpm. For that

reason, the engine has several devices designed to

protect it against potentially damaging conditions by

automatically shutting down the unit when the oil

pressure is too low, the coolant temperature is too

high, the coolant level is too low, or the engine is run-

ning too fast.

NOTE:

Engine protective switches and sensors are men-

tioned here for the reader’s convenience. Also

refer to the applicable control panel manual for

additional automatic engine shutdown informa-

tion.

HIGH COOLANT TEMPERATURE SWITCH 

The switch will close if the temperature should

exceed approximately 140° C (284° F), initiating an

engine shutdown. The generator will automatically

restart and the LED will reset once the temperature

has returned to a safe operating level.

LOW COOLANT LEVEL SENSOR 

To prevent overheating, the engine has a low coolant

level sensor. If the level of engine coolant drops below

the level of the low coolant level sensor, the engine

automatically shuts down.

LOW OIL PRESSURE SWITCH 

This switch has normally closed contacts that are

held open by engine oil pressure during cranking and

operating. Should oil pressure drop below the 8 psi

range, switch contacts close, and the engine shuts

down. The unit should not be restarted until oil is

added, and the AUTO/OFF/MANUAL switch must be

turned to OFF and then back to AUTO.

OVERCRANK SHUTDOWN 

After a prespecified duration of cranking, this func-

tion ends the cranking if the engine has failed to

start. The overcrank LED will turn ON. Turn OFF the

AUTO/OFF/MANUAL switch, then turn switch back to

AUTO to reset the generator control board.

NOTE:

If the fault is not corrected, the overcrank feature

will continue to activate.

Approximate Crank Cycle Times

• 15 seconds ON

• 7 seconds OFF

• 7 seconds ON

• 7 seconds OFF

• Repeat for 45 seconds

Approximately 90 seconds total.

OVERSPEED SHUTDOWN 

A speed circuit controls engine cranking, start-up,

operation and shutdown. Engine speed signals are

delivered to the circuit board whenever the unit is

running. Should the engine overspeed above a safe,

preset value, the circuit board initiates an automatic

engine shutdown. Contact the nearest Authorized

Dealer if this failure occurs.

RPM SENSOR LOSS SHUTDOWN 

If the speed signal to the control panel is lost, engine

shutdown will occur.

DC FUSES 

Fuse F1 (15 amp) is located inside of the control

panel. It protects the panel wiring and components

from damaging overload. Always remove this fuse

before commencing work on the generator. The

unit will not start or crank if the fuse is blown.

Fuse F2 (25 amp) is located in the engine wire har-

ness adjacent to the DC alternator. It is used to pre-

vent circuit failure due to DC alternator falure. If this

fuse is blown, battery charging will not occur while

the engine is running. Replace these fuses with the

same size, type, and rating. (See the exploded views

and parts lists at the end of this manual for replace-

ment part number.)

4-1

Stationary Emergency Generator

Engine Protective Devices

EngProt001 Rev. B 09/08

FUEL SYSTEM

FUEL REQUIREMENTS 

The Stationary Emergency Generator may be equipped with one of

the following fuel systems:

Natural gas fuel system•

Propane vapor (PV) fuel system•

Liquid propane (LP) fuel system•

Recommended fuels should have a Btu content of at least 1,000

Btu's per cubic foot for natural gas; or at least 2,520 Btu's per

cubic foot for LP gas. Ask the fuel supplier for the Btu content of

the fuel.

Required fuel pressure for natural gas is 5 inches to 14 inches

water column (0.18 to 0.5 psi); and for liquid propane, 5 inches

to 14 inches of water column (0.18 to 0.5 psi).

NOTE:

Any piping used to connect the generator to the fuel supply

should be of adequate size to ensure the fuel pressure NEVER

drops below five inches water column for natural gas or 5

inches water column for propane vapor for all load ranges. The

fuel supply piping shall be sized according to the installation

manual using the fuel consumption requirements identified in

the Specifications section of the Owner's Manual.

NOTE:

It is the responsibility of the installer to make sure that only

the correct recommended fuel is supplied to the generator fuel

system. Thereafter, the owner/operator must make certain that

only the proper fuel is supplied.

NATURAL GAS FUEL SYSTEM 

Natural gas is supplied in its vapor state. In most cases, the gas

distribution company provides piping from the main gas distribu-

tion line to the standby generator site. The following information

applies to natural gas fuel systems.

Gas pressure in a building is usually regulated by national, state •

and local codes.

To reduce gas pressure to a safe level before the gas enters a •

building, a primary regulator is needed. The natural gas supplier

may or may not supply such a regulator.

It is the responsibility of the gas supplier to make sure sufficient •

gas pressure is available to operate the primary regulator.

Gas pressure at the inlet to the fuel shutoff solenoid should not •

exceed approximately 14 inches water column (0.5 psi).

PROPANE VAPOR WITHDRAWAL FUEL SYSTEM 

This type of system utilizes the vapors formed above the liquid

fuel in the supply tank. Approximately 10 to 20 percent of the tank

capacity is needed for fuel expansion from the liquid to the vapor

state. The vapor withdrawal system is generally best suited for

smaller engines that require less fuel. The installer should be aware

of the following:

When ambient temperatures are low and engine fuel consump-•

tion is high, the vapor withdrawal system may not function

efficiently.

Ambient temperatures around the supply tank must be high •

enough to sustain adequate vaporization, or the system will not

deliver the needed fuel volume.

In addition to the cooling effects of ambient air, the vaporization •

process itself provides an additional cooling effect.

LP LIQUID FUEL SYSTEM 

LP is supplied as a liquid in pressure tanks. It is usually made up

of propane, butane, or a mixture of the two gases. Propane tends

to vaporize readily even at temperatures as low as -20° F (-29° C).

However, butane reverts to its liquid state when temperatures drop

below 32° F (0° C).

LP in a liquid withdrawal system must be converted to its gaseous

state before it is introduced into the engine carburetor. A vaporizer-

converter is generally used to accomplish this. In such a converter,

heated engine coolant is ported through the converter to provide

the necessary heat for conversion of the fuel from a liquid to a

gaseous state.

5-1

Stationary Emergency Generator

Fuel Systems

FuelSys001 Rev. D 07/09

SPECIFICATIONS

GENERATOR

Type ............................................................................. Synchronous

Rotor Insulation ....................................................................Class F

Stator Insulation ...................................................................Class F

Total Harmonic Distortion .........................................................< 5%

Alternator Output Leads 3-phase ........................................... 4-wire

Bearings .........................................................................Sealed Ball

Coupling .......................................................................Flexible Disc

Load Capacity (Standby Rating) ............................................20kW*

*

NOTE: Generator rating and performance in accordance with ISO8528-5, BS5514, SAE J1349,

ISO3046 and DIN 6271 Standards. KW rating is based on LPG fuel and may derate with natural

gas.

Excitation System ....................................................................Direct

Generator Output Voltage/kW - 60 Hz kW Amp CB Size

120/240V, 1-phase, 1.0 pf 20 83 100

120/208V, 3-phase, 0.8 pf 20 69 80

Generator Locked Rotor KVA Available @ Voltage Dip of 35%

Single-phase or 208 3-phase ............................................. 30 KVA

ENGINE

Make ................................................................................... Generac

Model ..................................................................................... In Line

Cylinders and Arrangement ............................................................ 4

Displacement ....................................................................... 1.6 Liter

Bore ...................................................................................... 3.15 in.

Stroke ................................................................................... 3.13 in.

Compression Ratio .............................................................9.75-to-1

Air Intake System ...............................................Naturally Aspirated

Valve Seats ................................................................... Replaceable

Lifter Type .......................................................................... Hydraulic

Engine Parameters

Rated Synchronous RPM ..............................................60 Hz, 3600

HP at rated kW ....................................................................... 35 HP

Exhaust System

Exhaust Flow at Rated Output 60 Hz .................................. 177 cfm

Exhaust Temperature at Rated Output .................................. 910° F

Combustion Air Requirements (Natural Gas)

Flow at rated power, 60 Hz ................................................... 80 cfm

Governor

Type .................................................................................. Electronic

Frequency Regulation ...................................................Isochronous

Steady State Regulation ........................................................± .25%

Adjustments:

Speed ............................................................................ Selectable



Engine Lubrication System

Type of Oil Pump ...................................................................... Gear

Oil Filter .............................................................Full Flow, Cartridge

Crankcase Oil Capacity ....................................................4 U.S. qts.

COOLING SYSTEM

Type ....................................................................................... Closed

Water Pump .................................................................... Belt Driven

Fan Speed ................................................................................ 2550

Fan Diameter .....................................................................16 inches

Fan Mode ..............................................................................Pusher

Air Flow (inlet air including alternator and

combustion air) .......................................................... 1528 ft3/min.

Coolant Capacity ...........................................................2.0 U.S. gal.

Heat Rejection to Coolant ..........................................107,000 Btu/h

Maximum Operating Air Temp. on Radiator ..............60° C (150° F)

Maximum Ambient Temperature ................................50° C (140° F)

FUEL SYSTEM

Type of Fuel ......................................... Natural Gas, Propane Vapor

Carburetor ...................................................................... Down Draft

Secondary Fuel Regulator .................................................Standard

Fuel Shut-off Solenoid ........................................................Standard

Operating Fuel Pressure ...................... 5 in. - 14 in. Water Column

Fuel Consumption - ft

3

/hr (Natural Gas/LPV)

Exercise 25% 50% 75% 100%

Cycle Load Load Load Load

59/23 124/49 188/75 250/99 315/125

ELECTRICAL SYSTEM

Battery Charge Alternator ............................................12V, 15 Amp

Static Battery Charger ............................................................2 Amp

Recommended Battery ...................................... Group 26, 525CCA

System Voltage .....................................................................12 Volts

Voltage Regulator

Type .................................................................................. Electronic

Sensing ........................................................................ Single-phase

Regulation ................................................................................± 1%

Features ................................................. V/F Adjustable, Adjustable

Voltage and Gain LED Indicators

Power Adjustment for Ambient Conditions

Temperature Deration

3% for every 10° C above °C ..................................................... 40

1.65% for every 10° above °F .................................................. 104

Altitude Deration

1% for every 100 m above m ................................................... 914

3% for every 1000 ft. above ft. ............................................... 3000

Controller .................................................R-200



6-1

Standby Generator Sets

Specifications

GenSpec030 Rev. 0 05/06

COLD WEATHER KIT

For cold climates, optional cold weather kit (part

number 0F6148) is recommended. The kit includes:

• Battery Warmer

• 4” Junction Box with hardware

• 6 qt. pack 5W-30 synthetic oil (engine)

RECONFIGURING THE FUEL SYSTEM

NOTE:

All models are configured for natural gas or LP

vapor from the factory.

To reconfigure the fuel system from NG to LP, follow

these steps:

1. Turn the main gas supply off.

2. Remove the carburetor fuel hose from the outlet

port (Port 1) of the demand regulator (Figure

6.2).

3. Remove the brass hose fitting from the outlet port

(Port 1) of the demand regulator.

4. Remove pipe plug from Port 2.

5. Install brass hose fitting into Port 2.

6. Install pipe plug into Port 1.

7. Connect carburetor gas hose to brass fitting.

8. Tighten all clamps and plugs.

9. Make sure fuel supply is of the proper pressure

and type for configuration.



10. Reverse the procedure to convert back to natural

gas.

11. The Dip switch inside the control panel must be

in the LP or NG position when switching to differ-

ent fuels.

Figure 6.2 — Reconfigure the Fuel System

NG FUEL SYSTEM

LP FUEL SYSTEM

Port 1

Port 2

FUEL HOSE

BRASS HOSE

FITTING

HOUSING

PORTS

OUT

PORT 2

PLUG

FUEL HOSE

BRASS HOSE

FITTING

HOUSING

PORTS

PLUG

OUT

PORT 1

NOTE:

Port 1 is for NG only and Port 2 is for LP vapor

only. No provision for dual fuel has been made.

DANGER



Serious injury or damage may occur if not con-

figured properly. Please consult an Authorized

Dealer with any questions.

TO

ALTERNATOR

NEUTRAL

GROUND

CIRCUIT

BREAKER

NEUTRAL

Ground Level

Concrete Slab

STUB-UP AREA

See Install Dwg for

Dimensions

CONTROL PANEL

GENERATOR

CONNECTION

BOX

FRAME RAIL

N1

N2

23

194

186

178

To Generator Control Panel

Utility In

Load

Out

Gen

N1

N2

23

194

183

178

120 Volt +

Neutral

Grd

Battery

Charger

Input

Transfer Switch

CIRCUIT BREAKER SIZE

KW VOLTS / AMPS LUG SIZE

25 240 1 Ø 125 #4 to 1/0

25 208 3 Ø 100 #4 to 1/0

4- # 14 GA

WIRES TO

GENERATOR

CONNECTION

BOX

TO GENERATOR

CONNECTION BOX

Figure 1 — Interconnections

6-2

Standby Generator Sets

Specifications

GenSpec030 Rev. 0 05/06

ALTERNATOR AC LEAD CONNECTIONS

See “Voltage Codes”. This Stationary Emergency

Generator may be rated at any one of three voltages,

either single-phase or three-phase. The electrical

wires in the unit’s AC connection (lower) panel should

be installed according to the number of leads and the

voltage/phase required for the application. If there

are any questions regarding lead connection, refer to

the wiring diagrams at the back of this manual.

Voltage codes apply to the type of stator assembly

installed on a particular generator.

FOUR-LEAD, SINGLE-PHASE STATOR 

Four-lead alternators (see Figure 7.1) are designed

to supply electrical loads with voltage code “A” (240V,

1-phase, 60 Hz). Electrical power is produced in the

stator power windings. These windings were con-

nected at the factory to the main circuit breaker as

shown in Figure 7.1.

The rated voltage between each circuit breaker ter-

minal is 240V. The rated voltage between each circuit

breaker terminal and the neutral point 00 is 120V.

Figure 7.1 — Four-lead, Single-phase Stator

ALTERNATOR POWER WINDING

CONNECTIONS

3-PHASE ALTERNATORS 

The Stationary Emergency Generator is designed

to supply 3-phase electrical loads. Electric power is

produced in the alternator power windings. These

windings were connected at the factory to the main

circuit breaker with a “Y” configuration as shown in

Figures 7.2 and 7.3.

The rated voltage between circuit breaker terminals

E1-E2, E1-E3 and E2-E3 is either 480V or 208V

depending on the model.

The rated voltage between each circuit breaker termi-

nal and the neutral point 00 is either 277V or 120V

depending on the model.

Figure 7.2 — Stator Power Winding

Connections - 3-phase, 277/480V (6 Lead)

S6

E

3

S3

INTERNAL

CO

NNE

C

TI

O

N

S

L-

N

L

-

L

S4

E2

S2

S5

S1

E1

NE

U

TRA

L

Figure 7.3 — Stator Power Winding

Connections - 3-phase, 120/208V (6 Lead)

E

3

E2

00

(

NEUTRAL

)

E1

L

-

L

-

N

S1

S4

S

6

S6

S3

S5

S2

7-1

Stationary Emergency Generator

General Information

ACConn001 Rev. A 10/08

INSTALLATION

Refer to the separate “Installation Guide QT Product

Line” supplied with the unit.

PREPARATION BEFORE START-UP

The instructions in this section assume that the

Stationary Emergency Generator has been properly

installed, serviced, tested, adjusted and otherwise

prepared for use by a competent, qualified installa-

tion contractor. Be sure to read the “Safety Rules”, as

well as all other safety information in this manual,

before attempting to operate this (and related) equip-

ment.

Before starting the generator for the first time, the

installer must complete the following procedures. For

follow-up maintenance information and/or service

intervals, please refer to the “Maintenance” section

and the “Service Schedule”.

TRANSFER SWITCH 

If this generator is used to supply power to any elec-

trical system normally powered by an electric utility,

the National Electrical Code requires that a transfer

switch be installed. The transfer switch prevents elec-

trical backfeed between two different electrical sys-

tems. (For additional information, see the applicable

transfer switch manual for this unit.) The transfer

switch, as well as the generator and other electrical

components, must be properly located and mounted

in strict compliance with applicable codes, standards

and regulations.

FUEL SYSTEM 

Make sure the fuel supply system to the genera-

tor (a) delivers the correct fuel at the correct pres-

sure and (b) is properly purged and leak tested

according to code. No fuel leakage is permitted. See

“Specifications” for more information.

GENERATOR SET LUBRICATION 

Check the engine crankcase oil level before operating

and add oil to the proper level – the dipstick “FULL”

mark. Never operate the engine with the oil level

below the dipstick “ADD” mark. See “Specifications”

and “Engine Oil Recommendations”.

NOTE:

This engine is shipped from the manufacturer

with “break-in” oil. This oil should be changed

after 30 hours of operation.

Check the oil level in the generator gearbox (if so

equipped) prior to initial use and at the intervals

indicated by the “Service Schedule.” The recom-

mended oil is SAE 90 gear lubricant.

Also, if the engine is equipped with a mechanical gov-

ernor, make sure the governor is properly lubricated

with clean engine oil.

PRIOR TO INITIAL START-UP 



Prior to initially starting the generator, it must

be properly prepared for use. Any attempt to

crank or start the engine before it has been

properly serviced with the recommended types

and quantities of engine fluids (oil, coolant, fuel,

etc.) may result in an engine failure.

ENGINE COOLANT 

Have the engine cooling system properly filled with

the recommended coolant mixture. Check the system

for leaks and other problems. See “Specifications”

and “Coolant” sections.

BELT TENSION 

Check-the engine-fan belt tension and condition prior

to placing the unit into service and at recommended

intervals. Belt tension is correct when a force of

approximately 22 pounds (10 kg), applied midway

between pulleys, deflects the belt about 3/8- to 5/8-

inch (10 to 16 mm).

ELECTRICAL SYSTEM 

Make sure the generator is properly connected to an

approved earth ground.

Make sure the generator battery is fully charged,

properly installed and interconnected, and ready for

use.

NOTE:

Battery charger must be connected to 120 VAC, 15

amp circuit to operate.

Check to ensure that there are no loose electrical con-

nections. Restrain any loose wires to keep them clear

of any moving generator set components.

INITIAL INSPECTION FOR QT GENSET

STARTUP

Inspect for the following.

• Freight Damage.

• Manuals present.

• Fluid Levels (Oil, coolant, battery, Gear Drive).

• Correct fuel piping.

• Correct muffler installation for external applica-

tion.

• Adequate air flow, clearances and ventilation per

installation drawings and applicable codes.

• Correct AC and DC wire size, connections and

grounding. Control and communication wiring to/

from the transfer switch must be run in a separate

conduit from the AC power leads.

8-1

Stationary Emergency Generator

Installation

Install001 Rev. E 11/08

• Battery charger connection to 120 VAC.

• Communication wires connected between transfer

switch and generator (HTS only).

• Unit secured to pad.

START-UP CHECKLIST



Before working on the Stationary Emergency

Generator, ensure the following:

• The AUTO/OFF/MANUAL switch is in the OFF

position.

• The 120VAC supply to the battery charger is

switched OFF.

PREPARATION FOR START-UP 

• Ensure that the 120VAC circuit breaker to the bat-

tery charger is open.

• Remove the fuse from the the control panel. For

the H-100 and R-series: Open the front door of the

control box and remove the 15 Amp ATO fuse in

the lower left-hand corner of the control box.

• Connect the battery cables to the battery. Attach

negative battery cable last.

• Close the 120VAC circuit breaker to the battery

charger.

• Measure the voltage at the battery before and after

the charger is turned on.

• Verify all AC electrical connections are tight at the

circuit breaker and transfer switch.

• Visually inspect entire area looking for loose paper,

plastic wrappings, leaves, etc.

• Check all hoses clamps fittings for leaks or dam-

age.

• Check all electrical plugs throughout the genera-

tor. Ensure each plug is seated correctly and fully

inserted into its receptacle.

• Verify the AUTO/OFF/MANUAL switch is in OFF

position.

• Open the valve to the engine fuel line.

• Bleed the fuel system of air. (necessary for long fuel

lines).

• Open the generator main line circuit breaker.

• Connect a manometer to the gas line and record

the static pressure. It must be as listed in the

Specifications.

• Insert the fuse into the control panel.

• Move the AUTO/OFF/MANUAL switch to the MAN-

UAL position. The engine should now crank and

start.

• Check voltage at the generator terminals.

• For 3-phase units, check phase rotation at the

transfer switch terminals. The generator phase

rotation must match the utility phase rotation.

• Check for coolant, fuel, oil, and exhaust leaks.

• Close the generators main line circuit breaker.

• Turn the generator set off.

• Connect the UTILITY supply to the transfer

switch.

• Set the AUTO/OFF/MANUAL switch to AUTO.

• Disconnect utility power before the transfer

switch.

Engine should start, transfer to load.

Run at least 15 minutes on generator power.

Make certain all 3-phase loads are functioning

correctly (correct phase rotation).

• Reconnect Utility power

Transfer switch will transfer back to Utility and

engine will shut down within the given time

parameters set up for the specific transfer switch

and controller.

• Install all covers, access plates and door panels.

• Put the Owners Manual in a safe and accessible

place.

• Make certain the AUTO/OFF/MANUAL switch is in

the AUTO position.

START-UP INSPECTION 

When a start-up is performed by an Authorized

Service Dealer, a standard three-part form titled

“Start-up Inspection for Standby Power Systems”

(part no. 067377), should be completed by the instal-

lation technician or engineer. See page 1-3 for infor-

mation on locating the nearest Authorized Service

Dealer. The installer should complete the form and

disseminate copies as follows:

• White copy: Mail to Generac Warranty Department,

P.O. Box 340, 211 Murphy Dr., Eagle, WI 53119-

2062.

• Pink Copy: For service file of installing dealer.

• Yellow Copy: For the customer’s records.

8-2

Stationary Emergency Generator

Installation

Install001 Rev. E 11/08

STATIONARY EMERGENCY

GENERATOR CONTROL AND

OPERATION

Refer to the appropriate control panel operator’s manual for this

unit.

OPERATING UNIT WITH MANUAL

TRANSFER SWITCH

If the Stationary Emergency Generator was installed in conjunction

with a transfer switch capable of manual operation only, the fol-

lowing procedure applies. A manually operated transfer switch is

one that will not provide automatic start-up and does not include

an intelligence circuit.

ENGINE START-UP AND TRANSFER 

For additional information, refer to the applicable control panel

manual for this unit, as well as any literature pertaining to the

specific transfer switch.

DANGER



The Maintenance Disconnect Switch and the

AUTO/OFF/MANUAL switches (if so equipped)

must be set properly, or the generator will crank

and start as soon as the utility power to the

transfer switch is turned off. Refer to applicable

control panel and transfer switch manuals for

more information.



Do not proceed until certain that utility source

voltage is available to the transfer switch and

the transfer switch main contacts are set to

UTILITY.



Do not attempt manual operation until all power

supplies to the transfer switch have been posi-

tively turned off, or extremely dangerous - pos-

sibly lethal - electrical shock will result.



Transfer switch enclosure doors should be kept

closed and locked. Only authorized personnel

should be allowed access to the transfer switch

interior. Extremely high and dangerous voltages

are present in the transfer switch.

In order to transfer load from the utility source to the generator,

follow these directions:

Turn OFF or disconnect the utility power circuit to the transfer •

switch, using the means provided (such as the utility source

main line circuit breaker).

Set the transfer handle to its UTILITY (NORMAL) position with •

load circuits connected to the utility power supply.

Set the generator’s main line circuit breaker to its OFF (or OPEN) •

position.

Start the generator.•



Do not crank the engine continuously for longer

than 30 seconds, or the heat may

damage the starter motor.

Let engine stabilize and warm up.•

Check all applicable instrument and gauge readings. When •

certain that all readings are correct, move the transfer switch

manual handle to the STANDBY (or EMERGENCY STANDBY)

position, i.e., load circuits supplied by the generator.

Set the generator’s main line circuit breaker to its ON (or •

CLOSED) position.

Load circuits are now powered by the generator.•

RETRANSFER AND SHUTDOWN 

For additional information, refer to the applicable control panel

manual for this unit, as well as any literature pertaining to the

specific transfer switch.

To transfer the load back to the utility power source and shut down

the generator, follow these directions:

Set the generator’s main line circuit breaker to its OFF (or OPEN) •

position.

Manually move the transfer switch handle to its UTILITY •

(NORMAL) position, i.e., load circuits connected to the utility.

Turn ON the utility power supply to the transfer switch, using •

the means provided (such as the utility power source main line

circuit breaker).

Let the generator run at no-load for a few minutes to stabilize •

internal temperatures.

Shut down the generator.•

OPERATING UNIT WITH AUTOMATIC

TRANSFER SWITCH

If the Stationary Emergency Generator has been installed with an

automatic transfer switch, the engine may be started and stopped

automatically or manually.

NOTE:

Refer to the applicable manual for your transfer switch and to

“Transfer Switch Start Signal Connections”. In addition, please

note the dangers under “Engine Start-up and Transfer.”

9-1

Stationary Emergency Generator

Operation

Oper001 Rev. C 08/09

MAINTENANCE PERFORMED BY

SERVICE DEALERS



Before working on the Stationary Emergency

Generator, ensure the following:

The AUTO/OFF/MANUAL switch is in the OFF •

position.

The 15A fuse has been removed from the con-•

trol box.

The 120VAC supply to the battery charger is •

switched OFF.

EVERY THREE MONTHS 

1. Check battery condition.

2. Inspect and test fuel system.

3. Check transfer switch.

4. Inspect exhaust system.

5. Check engine ignition system.

6. Check fan belts.

ONCE EVERY SIX MONTHS 

1. Test Engine Safety Devices (low oil pressure, low

coolant level, high coolant temperature).

ONCE ANNUALLY 

1. Test engine governor; adjust or repair, if needed.

2. Clean, inspect generator.

3. Flush cooling system.

FIRST 30 OPERATING HOURS 

1. Change engine "break-in" oil and filter.

FIRST 100 OPERATING HOURS 

1. Change engine oil and oil filter. After initial

change, service engine oil and filter at 100 operat-

ing hours or six months, whichever comes first.

2. Retorque cylinder head.

3. Retorque intake and exhaust manifold.

EVERY 500 OPERATING HOURS 

1. Service air cleaner.

2. Check starter.

3. Check engine DC alternator.

COOLING SYSTEM

Air intake and outlet openings in the generator com-

partment must be open and unobstructed for contin-

ued proper operation. This includes such obstruc-

tions as high grass, weeds, brush, leaves and snow.

Without sufficient cooling and ventilating air flow, the

engine/generator quickly overheats, which causes it

to shut down. (See the installation diagram.)



The exhaust system parts from this product get

extremely hot and remains hot after shutdown.

High grass, weeds, brush, leaves, etc. must

remain clear of the exhaust. Such materials may

ignite and burn from the heat of the exhaust

system.

OVERLOAD PROTECTION FOR ENGINE

DC ELECTRICAL SYSTEM

Engine cranking, start up and running are controlled

by a solid state Engine Controller circuit board.

Battery voltage is delivered to that circuit board via

a 15 amp fuse. These overcurrent protection devices

will open if the circuit is overloaded.



If a circuit breaker opens or a fuse element

melts, find the cause of the overload before

resetting the circuit breaker or replacing the

fuse.

CHECKING FLUID LEVELS

CHECK ENGINE OIL 

Check engine crankcase oil level (Figure 10.1) at least

every 20 hours of operation, or prior to use.

Remove oil dipstick and wipe dry with a clean, lint-•

free cloth.

Install oil dipstick, then remove again.•

Oil should be between FULL and ADD marks.•

If oil level is below the dipstick ADD mark, remove •

oil fill cap-. Add the recommended oil to bring oil

level up to the FULL mark. DO NOT FILL ABOVE

THE “FULL” MARK. See “Engine Oil Recommen-

dations” for recommended oils.

10-1

Stationary Emergency Generator

Maintenance

Maint011 Rev. F 09/08

Figure 10.1 - Oil Dipstick and Oil Fill Cap

OIL FILL CAP

OIL

DIPSTICK

BATTERY FLUID 

Check battery electrolyte fluid based on the

Maintenance Schedule. Fluid should cover separa-

tors in all battery cells. If fluid level is low, add dis-

tilled water to cover tops of separators. DO NOT USE

TAP WATER IN BATTERY.

ENGINE COOLANT 

Check coolant level in coolant recovery bottle. See

Specifications.

Add recommended coolant mixture as necessary.•

Periodically remove radiator pressure cap (only •

when engine has cooled down) to make sure the

coolant recovery system is functioning properly.

Coolant should be at bottom of radiator filler neck.

If coolant level is low, inspect gasket in radiator

pressure cap. Replace cap, if necessary. To have

pressure cap tested, contact a Service Dealer.

Inspect cooling system and coolant recovery sys-

tem for leaks.

MAINTENANCE OWNER/OPERATOR

CAN PERFORM

CHECK ENGINE OIL LEVEL 

Refer to “Checking Fluid Levels”.

CHECK BATTERY 

See “Checking Fluid Levels”.•

Check battery cables for condition, tightness, cor-•

rosion or damage. Clean, tighten or replace as

necessary.

EXERCISE SYSTEM 

Start the Stationary Emergency Generator engine at

least once every seven days and let it run at least 20

minutes. For more detailed exercise information, see

the respective sections in the Control Panel Technical

Manual that is supplied with the unit.

INSPECT COOLING SYSTEM 

Inspect engine cooling system. See “Maintenance •

Schedule”.

Check hoses for damage, deterioration, leaks, etc. •

Correct any discrepancies found.

Check hose clamps for tightness.•

CHECK ENGINE COOLANT LEVEL 

See “Checking Fluid Levels”.

PERFORM VISUAL INSPECTION 

Complete a thorough visual inspection of the entire

engine-generator monthly. Look for obvious damage,

loose, missing or corroded nuts, bolts and other fas-

teners. Look for fuel, oil or coolant leaks.

INSPECT EXHAUST SYSTEM 

Inspect the exhaust system at least once every three

months. Check all exhaust system pipes, mufflers,

clamps, etc. for condition, tightness, leaks, security,

damage.

CHECK FAN BELT 

Inspect fan belts every three months. Replace any •

damaged, deteriorated, worn or otherwise defec-

tive belt.

Check fan belt tension. Thumb pressure, exerted •

midway between pulleys, should deflect about 3/8

to 5/8 of an inch. Adjust belt tension as required.

INSPECT ENGINE GOVERNOR 

Visually inspect electronic governor.

DANGER



Do not attempt to adjust the governor. Only

qualified service facilities should adjust the

governor. Excessively high operating speeds

are dangerous and increase the risk of personal

injury. Low speeds impose a heavy load on the

engine when adequate engine power is not

available and may shorten engine life. Correct

rated frequency and voltage are supplied only

at the proper governed speed. Some connected

electrical load devices may be damaged by incor-

rect frequency and/or voltage. Only qualified

service technicians should adjust the governed

speed.

Stationary Emergency Generator

Maintenance

10-2

Maint011 Rev. F 09/08

CHANGING ENGINE OIL 

Refer to maintenance performed by service facilities

for engine oil and filter change frequencies.

Drain the oil while the engine is still warm from run-

ning. This means warm up the engine, shut it down

and drain immediately as follows:

1. Remove OIL DRAIN HOSE from its retaining

clip.

2. Loosen and remove OIL DRAIN HOSE CAP. Drain

oil completely into suitable container.

3. When all oil has drained, install and tighten OIL

DRAIN HOSE CAP, and re-install into its retaining

clip.

4. Turn OIL FILTER (Figure 10.2) counterclockwise

and remove. Properly dispose of old filter.

Figure 10.2 – Oil Filter

OIL

FILTER

OIL

DIPSTICK

5. Apply light coating of new engine oil to seal of new

oil filter.-Install FILTER and tighten by hand only.

DO NOT OVER TIGHTEN.

6. Remove OIL FILL CAP. Add recommended oil (see

SPECIFICATIONS). DO NOT FILL ABOVE THE

DIPSTICK “FULL” MARK. Crankcase oil capacity

is 4.0 U.S. quarts (3.8 liters).



After refilling the crankcase with oil, always

check oil level on dipstick. NEVER OPERATE

ENGINE WITH OIL BELOW THE DIPSTICK “ADD”

MARK.

7. Start engine and check for oil leaks.

CHANGING THE ENGINE AIR CLEANER 

To replace the engine air cleaner, simply remove the

air cleaner cover and replace the air filter making

sure it is positioned properly before reattaching the

cover (Figure 10.3).

See the “Service Schedule,” for air cleaner mainte-

nance.

Figure 10.3 – Engine Air Cleaner

Air Cleaner

(Doors Removed for Clarity)

SPARK PLUGS 

Reset the spark plug gap or replace the spark plugs

as necessary (Figure 10.4).

1. Clean the area around the base of the spark plugs

to keep dirt and debris out of the engine. Clean

by scraping or washing using a wire brush and

commercial solvent. Do not blast the spark plugs

to clean.

2. Remove the spark plugs and check the condition.

Replace the spark plugs if worn or if reuse is

questionable. See the “Service Schedule” section

for recommended inspection.

3. Check the spark plug gap using a wire feeler

gauge. Adjust the gap to 0.76 mm (0.030 inch)

by carefully bending the ground electrode (Figure

10.4).

Figure 10.4 – Setting the Spark Plug Gap

COOLANT CHANGE 

Every year, have a service facility drain, flush and

refill the cooling system. See “Specifications” for cool-

ing system recommendations.

Stationary Emergency Generator

Maintenance

10-3

Maint011 Rev. F 09/08

SET PLUG GAP AT 0.76 mm

(0.030 inch)

MISCELLANEOUS MAINTENANCE

CLEANING THE STATIONARY EMERGENCY 

GENERATOR

Keep the generator as clean and as dry as possible.

Dirt and moisture that accumulates on internal gen-

erator windings have an adverse effect on insulation

resistance.

Periodically clean generator exterior surfaces. A soft

brush may be used to loosen caked on dirt. Use a

vacuum system or dry, low pressure air to remove

any accumulations of dirt. The generator is housed

inside an all-weather enclosure, clean the enclosure

with a soft, damp cloth or sponge and water.

Once each year have the generator cleaned and

inspected by a Service Dealer. That dealer will use

dry, low pressure air to clean internal windings. Parts

inside the control console should be cleaned and

inspected at this time as well.

Finally, have the insulation resistance of stator and

rotor windings checked. If insulation resistances are

excessively low, the generator may require drying.

BATTERY 

All lead-acid storage batteries discharge when not in

use. Refer to specific instructions and warnings that

accompany the battery. If such information is not

available, observe the following precautions when

handling a battery:

DO NOT use jumper cables and a booster battery •

to crank or start the generator engine.

DO NOT recharge a weak battery while it is •

installed in the generator. Remove battery from

generator and recharge in a well-ventilated area,

away from fuel vapors, sparks, heat or flames.

Battery electrolyte fluid is an extremely caustic •

sulfuric solution that can cause severe burns. DO

NOT permit fluid to contact eyes, skin, clothing,

painted surfaces, wiring insulation, etc. If any bat-

tery fluid is spilled, flush the affected area with

clear water immediately.

Always wear safety glasses, rubber apron and •

gloves when handling a battery.

Batteries give off explosive hydrogen gas while •

charging. The gas can form an explosive mixture

around the battery for several hours after charging.

Any spark, heat or flames can ignite the gas and

cause an explosion which can shatter the battery,

causing blindness or other serious injury.

BATTERY MAINTENANCE 

The battery should be inspected per the Scheduled

Maintenance section. The following procedure should

be followed for inspection:

1. Inspect the battery posts and cables for tightness

and corrosion. Tighten and clean as necessary.

2. Check the battery fluid level of unsealed batteries

and, if necessary, fill with DISTILLED WATER

ONLY. DO NOT USE TAP WATER IN BATTERIES.

3. Have the state of charge and condition checked.

This should be done with an automotive-type bat-

tery hydrometer.

DANGER



Storage batteries give off explosive hydrogen

gas. This gas can form an explosive mixture

around the battery for several hours after charg-

ing. The slightest spark can ignite the gas and

cause an explosion. Such an explosion can shat-

ter the battery and cause blindness or other

injury. Any area that houses a storage battery

must be properly ventilated. Do not allow smok-

ing, open flame, sparks or any spark producing

tools or equipment near the battery.



Battery electrolyte fluid is an extremely corro-

sive sulfuric acid solution that can cause severe

burns. Do not permit fluid to contact eyes, skin,

clothing, painted surfaces, etc. Wear protective

goggles, protective clothing and gloves when

handling a battery. If fluid is spilled, flush the

affected area immediately with clear water.



Do not use any jumper cables or booster battery

to crank and start the generator engine. If the

battery has completely discharged, remove it

from the generator for recharging.



Be sure the AUTO/OFF/MANUAL switch is set to

the OFF position, before connecting the battery

cables. If the switch is set to AUTO or MANUAL,

the generator can crank and start as soon as the

battery cables are connected.



Be sure the 120VAC power supply to the battery

is turned OFF, or sparking may occur at the bat-

tery posts as the cables are attached and cause

an explosion.

BATTERY REPLACEMENT 

NOTE:

Unit DOES NOT include battery.

When supplying or replacing the battery, the recom-

mended number and type of battery is listed in the

Specifications Section.

NOTE:

The BCI number should be located directly on the

battery.

REPAIR PARTS 

The latter portion of this manual consists of exploded

views, parts lists and electrical data pertaining to this

generator set. The parts lists consist of (a) an item

number, (b) a part number, (c) the quantity required,

and (d) a description of the part. The item number

corresponds to an identical number on the exploded

view drawing.

Stationary Emergency Generator

Maintenance

10-4

Maint011 Rev. F 09/08

SERVICE SCHEDULE

The following is a recommended maintenance schedule for Stationary Emergency Generator sets. The established intervals in the schedule

are the maximum recommended when the unit is used in an average service application. They will need to be decreased (performed more

frequently) if the unit is used in a severe application. Use calendar time or accumulated run time, from the previous maintenance interval to

determine the next required maintenance interval.

Service Maintenance Interval Information:

The various service maintenance intervals are designated by interval numbers as follows:

1 An early inspection of the generator set to insure it is ready to operate when required and to identify any potential problem areas.

Performed monthly this requires approximately .5 man-hours per unit to complete.

This inspection may be performed by the end user providing the following safety steps are taken to prevent the engine from starting

automatically without warning:

To prevent injury, perform the following steps in the order indicated before starting any maintenance:

• Disable the generator set from starting and/or connecting to the load by setting the control panel

AUTO/OFF/MANUAL switch to the OFF position.

• Remove the 5 amp and 15 amp control panel fuses.

• Turn off the battery charger (turn OFF utility supply to ATS).

• Remove the negative battery cable.

The battery charger must be turned off BEFORE removing the battery cable to prevent an over current condition from burning out

sensitive control panel components and circuits.

Following all maintenance, reverse these steps to insure the unit is returned to standby setup for normal

operation when required.

2 A break-in service inspection of the generator set to insure it is ready to operate and carry the load when required, and to identify any

potential problem areas.

Performed ONLY ONCE following the first three months, or 30 run time hours of operation after purchase of the unit and requires approxi-

mately 2.5 man-hours per unit to complete.

This inspection contains some maintenance tasks which require special tools, equipment, and/or knowledge to accomplish and should be

performed only by a Service Dealer.

3 An operational inspection of the generator set to insure it is ready to operate and carry the load when required, and to identify any potential

problem areas.

Performed semi-annually this requires approximately 1.5 man-hours per unit to complete.

This inspection contains some maintenance tasks which require special tools, equipment, and/or knowledge to accomplish and should be

performed only by a Service Dealer.

4 A mid-level inspection of the generator set to insure it is ready to operate and carry the load when required, and to identify any potential

problem areas.

Performed annually this requires approximately 4.0 man-hours per unit to complete.

This inspection contains some maintenance tasks which require special tools, equipment, and/or knowledge to accomplish and should be

performed only by a Service Dealer.

11-1

Stationary Emergency Generator

Service Schedule

SrvSchd002 Rev. E 07/09

Page is loading ...

Generac 20 kW 0053371 User manual

Generac 20 kW 0053371 User manual

Other documents