FMI DVM36VNE Owner's manual

Brand: FMI

Model: DVM36VNE

Category: Fireplaces

Type: Owner's manual

DIRECT-VENT FIREPLACE

OWNER’S OPERATION AND INSTALLATION MANUAL

NATURAL GAS MODELS (V)VC36NE SERIES

PROPANE/LP GAS MODELS (V)VC36PE SERIES

For more information, visit www.desatech.com

WARNING: If the information in this manual is not

followed exactly, a re or explosion may result causing

property damage, personal injury or loss of life.

— Do not store or use gasoline or other ammable

vapors and liquids in the vicinity of this or any other

appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the re

department.

— Installation and service must be performed by a quali-

ed installer, service agency or the gas supplier.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

Patent Pending

www.desatech.com

116235-01K2

SAFETY

WARNING: Improper

installation, adjustment,

alteration, service or

maintenance can cause

injury or property dam-

age. Refer to this manual

for correct installation

and operational proce-

dures. For assistance or

additional information

consult a qualified in-

staller, service agency or

the gas supplier.

This appliance may be in-

stalled in an aftermarket,*

permanently located,

manufactured (mobile)

home, where not prohib-

ited by local codes.

This appliance is only for

use with the type of gas

indicated on the rating

plate. This appliance is

not convertible for use

with other gases, unless

a certied kit is used.

* Aftermarket: Completion of sale, not for

purpose of resale, from the manufacturer

State of Massachusetts:

The installation must be

made by a licensed plumber

or gas tter in the Common-

wealth of Massachusetts.

WARNING: This product

contains and/or generates

chemicals known to the State

of California to cause cancer or

birth defects or other reproduc-

tive harm.

IMPORTANT: Read this owner’s

manual carefully and completely

before trying to assemble, op-

erate or service this log set.

Improper use of this log set can

cause serious injury or death

from burns, fire, explosion,

electrical shock and carbon

monoxide poisoning.

DANGER: Carbon monoxide

poisoning may lead to death!

This replace must be installed by a qualied

(certied or licensed) service person. It has

a sealed gas combustion chamber that uses

a coaxial pipe (pipe within a pipe and having

the same center) venting system. It brings in

fresh air for combustion through the outer pipe

and combustion gases are exhausted through

the inner pipe. If the glass door assembly and

venting pipe are not properly seated, con-

nected and sealed, carbon monoxide leakage

(spillage) can occur.

TABLE OF CONTENTS

Safety .................................................................. 2

Product Identication ........................................... 4

Local Codes......................................................... 5

Product Features ................................................. 5

Pre-Installation Preparation ................................. 5

Location of Termination Cap ................................ 8

Venting Installation............................................... 9

Fireplace Installation.......................................... 19

Wiring Diagram .................................................. 27

Operation ........................................................... 28

Inspecting Burners............................................. 29

Cleaning and Maintenance ................................ 30

Troubleshooting ................................................. 31

Replacement Parts ............................................ 34

Service Hints ..................................................... 34

Technical Service............................................... 34

Specications .................................................... 34

Accessories ....................................................... 35

Parts .................................................................. 36

Warranty ..............................................Back Cover

www.desatech.com

116235-01K 3

Carbon Monoxide Poisoning: Early signs

of carbon monoxide poisoning resemble the

u, with headaches, dizziness or nausea. If

you have these signs, the log set may not

be working properly. Get fresh air at once!

Have log set serviced. Some people are

more affected by carbon monoxide than oth-

ers. These include pregnant women, people

with heart or lung disease or anemia, those

under the inuence of alcohol and those at

high altitudes.

Natural and Propane/LP Gas: Natural and

propane/LP gas are odorless. An odor-making

agent is added to the gas. The odor helps you

detect a gas leak. However, the odor added to

the gas can fade. Gas may be present even

though no odor exists.

Make certain you read and understand all

warnings. Keep this manual for reference. It

is your guide to safe and proper operation of

this replace.

WARNING: Any change to

this replace or it’s controls can

be dangerous. Do not modify

this replace under any circum-

stances. Any parts removed for

servicing must be replaced prior

to operating replace.

WARNING: Do not use a

blower insert, heat exchanger

insert or other accessory not

approved for use with this re-

place.

WARNING: This appliance

is only for use with the type of

gas indicated on the rating plate.

This appliance is not convertible

for use with other gases unless

a certied kit is used.

SAFETY

Continued

WARNING: Do not allow fans

to blow directly into the replace.

Avoid any drafts that alter burner

ame patterns.

Due to high temperatures, the

appliance should be located out

of trafc and away from furniture

and draperies.

Do not place clothing or other

ammable material on or near

the appliance. Never place any

objects on the appliance.

Do not use this replace to cook

food or burn paper or other am-

mable material.

This replace reaches high tem-

peratures. Keep children and

adults away from hot surface to

avoid burns or clothing ignition.

Fireplace will remain hot for a

time after shutdown. Allow sur-

face to cool before touching.

Carefully supervise young chil-

dren when they are in the room

with replace.

Keep the area around your

replace clear of combustible

materials, gasoline and other

ammable vapor or liquids. Do

not run replace where these

are used or stored.

1. For propane/LP replace, do not place

propane/LP supply tank(s) inside any

structure. Locate propane/LP supply

tank(s) outdoors. To prevent performance

problems, do not use propane/LP fuel tank

of less than 100 lb. capacity.

www.desatech.com

116235-01K4

2. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do

not use any phone in your building

• immediately call your gas supplier from

a neighbor’s phone. Follow the gas

supplier's instructions

• if you cannot reach your gas supplier,

call the re department.

3. Never install the replace

• in a recreational vehicle

• in windy or drafty areas where curtains

or other combustible (flammable)

objects can make contact with the

replace front

• in high trafc areas

4. Turn fireplace off and let cool before

servicing, installing or repairing. Only a

qualied service person should install,

service or repair this replace. Have re-

place inspected annually by a qualied

service person.

5. You must keep control compartments,

burners and circulating air passages

clean. More frequent cleaning may be

needed due to excessive lint and dust

from carpeting, bedding material, etc.

SAFETY

Continued

Turn off the gas valve and pilot light before

cleaning replace.

6. Have venting system inspected annually by

a qualied service person. If needed, have

venting system cleaned or repaired. See

Cleaning and Maintenance, page 30.

7. Do not use any solid fuels (wood, coal,

paper, cardboard, etc.) in this replace.

Use only the gas type indicated on re-

place nameplate.

8. This appliance, when installed, must be

electrically grounded in accordance with

local codes or, in the absence of local

codes, with the National Electrical Code,

ANSI/NFPA 70 or the Canadian Electrical

Code, CSA C22.1.

9. Do not use replace if any part has been

exposed to or under water. Immediately

call a qualied service person to arrange

for replacement of the unit.

10. Do not operate replace if any log is

broken.

11. Do not operate replace with glass door

removed, cracked or broken.

12. Provide adequate clearances around air

openings.

Figure 1 - Direct-Vent Fireplace with Millivolt Ignition

PRODUCT IDENTIFICATION

Glass Door

Assembly

Switch Bracket for Optional

Remote and Blower

Electronic Control Valve

Log Set

Lava Rock

Glowing

Embers

Upper Louver Panel

Lower Louver Panel

Flue Collar

Nailing Flange

Burner

Assembly

www.desatech.com

116235-01K 5

These are a few facts that can help you under-

stand and enjoy your direct-vent replace:

• The venting system may be routed to the

outside of your home in several ways. It

may vent through the roof (vertical) or it

may vent to an outside/exterior wall (hori-

zontal). The vent pipe installation is very

important to allow for proper operation.

You must follow the venting instructions

very carefully for either vertical or horizontal

applications.

• This replace may be installed in any room

of your house provided all local codes and

these installation instructions are followed.

Figure 2 - Common Fireplace Locations

Flush with a wall

Through exterior wall

enclosed in a chase

Corner

installation

Figure 3 - Fireplace Bottom Dimensions

29"

41"

LOCAL CODES

LOCATION AND SPACE

REQUIREMENTS

Determine the safest and most efcient loca-

tion for your DESA Heating, LLC direct-vent

replace. Make sure that rafters and wall

studs are not in the way of the venting system.

Choose a location where the heat output is

not affected by drafts, air conditioning ducts,

windows or doors. Figure 2 shows some com-

mon locations. Be aware of all restrictions and

precautions before deciding the exact location

for your replace and termination cap.

When deciding the location of your replace,

follow these rules:

• Do not connect this replace venting to a

chimney ue serving a separate solid-fuel

burning replace or appliance.

• Due to high temperatures, do not locate this

replace in high trafc areas, windy or drafty

areas or near furniture or draperies.

• Proper clearances must be maintained.

• If your replace is to be installed directly on

carpeting, vinyl tile or any combustible mate-

rial other than wood, it must be installed on a

metal or wood panel extending the full width

and depth of the replace. See Figure 3.

Install and use replace with care. Follow all

local codes. In the absence to local codes,

use the current National Fuel Gas Code ANSI

Z223.1/NFPA 54* (USA) or the current CSA-

B149.1 Installation Code (Canada).

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

PRODUCT FEATURES

• The blower requires electricity. If you plan

to install the blower at a later date, do not

forget to wire the outlet at the bottom of the

replace when framing.

• Each time you turn on your replace, you

may notice some amount of condensation

on the inside of the replace glass. This

is normal and will disappear after 10-20

minutes of operation.

• Your direct-vent gas fireplace system

(replace and venting) is a balanced and

sealed gas operating unit. It requires ap-

proximately 10-20 minutes of operating

time before the ame pattern stabilizes.

PRE-INSTALLATION PREPARATION

www.desatech.com

116235-01K6

• Your replace is designed to be used in

zero clearance installations. Wall or framing

material can be placed directly against any

exterior surface on the back, sides or top of

your replace, except where standoff spac-

ers are integrally attached. If standoff spac-

ers are attached to your replace, these

spacers can be placed directly against wall

or framing material. See framing details on

page 7.

• If you plan on installing a television or

entertainment center recessed above

your replace, it is recommended that you

maintain a minimum 18" above top of louver

opening.

• When locating termination cap, it is impor-

tant to observe the minimum clearances

shown in Figure 7, page 8.

• If recessing into a wall, you can avoid extra

framing by positioning your replace against

an already existing framing member.

• Do not recess termination cap into a wall

or siding.

• You may paint the termination cap with

450º F (232º C) heat-resistant paint to

coordinate with the exterior nish.

• There must not be any obstruction such

as bushes, garden sheds, fences, decks

or utility buildings within 24" from the front

of the termination cap.

• Do not locate termination cap where exces-

sive snow or ice build up may occur. Be sure

to clear vent termination area after snow falls

to prevent accidental blockage of venting

system. When using snow blowers, do not

direct snow towards vent termination area.

PRE-INSTALLATION PREPARATION

Continued

CLEARANCES

Minimum clearances to combustibles for the

replace are as follows:

*Back and sides 0"

Perpendicular walls 6"

Floor 0"

Ceiling to louver opening 42"

Front 36"

Top of Standoffs 0"

Vent (See venting instruc-

tions for specic vent-

ing clearances.)

Combustible material with a maximum thick-

ness of 5/8" may be ush with the top front

of replace.

* For back and sides of replace, do not pack

with insulation or other materials. 0" clear-

ance to combustible materials are for framing

purpose only.

NOTICE: This replace is in-

tended for use as supplemental

heat. Use this replace along

with your primary heating sys-

tem. Do not install this replace

as your primary heat source.

If you have a central heating

system, you may run system’s

circulating blower while using

replace. This will help circulate

the heat throughout the house.

In the event of a power outage,

you can use this replace as a

heat source.

FRAMING AND FINISHING

Figure 4, page 7, shows typical framing of this

replace. Figure 5, page 7, shows framing for

corner installation. All minimum clearances

must be met.

For available accessories for this replace,

see Accessories on page 35. If you are using

a separate combustible mantel piece, refer to

Figure 6, page 7 for proper installation height.

You can install noncombustible mantels at any

height above the replace.

Note: Noncombustible mantels may dis-

color!

www.desatech.com

116235-01K 7

Figure 4 - Framing Clearances for

Installation Against an Exterior Wall

21" Horizontal Vent

" Vertical Vent

Top of Louver

Opening

Wall

Figure 5 - Framing Clearances for Corner

Installation

Figure 6 - Clearances for Combustible

Mantels

PRE-INSTALLATION PREPARATION

Continued

Nailing Tabs

Ref.

Mantel

Depth Ref.

Mantel from

Top of Louver

Opening

1 14" A 16"

2 12" B 14"

3 10" C 12"

4 8" D 10"

5 6" E 8"

6 4" F 6"

7 2" G 4"

41"

Nailing

Tabs

15"

www.desatech.com

116235-01K8

Figure 7 - Minimum Clearances for Termination Cap

LOCATION OF TERMINATION CAP

Fixed

Closed

Openable

Fixed

Closed

TERMINATION CAP

AIR SUPPLY INLET

GAS METER RESTRICTED AREA

(TERMINATION PROHIBITED)

A = clearance above grade, veranda, porch, deck, or

balcony [*12" (30.5 cm) minimum]

B = clearance to window or door that may be opened

[6" (15 cm) min. for 10,000 Btu or less; 9" (23 cm) in US

if between 10,000 and 50,000, 12" (30 cm) in Canada

if between 10,000 and 100,000; 12" (30 cm) in US if

greater than 50,000, 36" (91 cm) in Canada if greater

than 100,000]

C = clearance to permanently closed window

[minimum 12" (30.5 cm) recommended to prevent

condensation on window]

D = vertical clearance to ventilated soffit located above the

terminal within a horizontal distance of 24" (61 cm) from

the center-line of the terminal [18" (45.7 cm) minimum]

E = clearance to unventilated soffit [12" (30.5 cm) minimum]

F = clearance to outside corner (see below)

G = clearance to inside corner (see below)

H = *not to be installed above a meter/regulator assembly

within 36" (91.4 cm) horizontally from the center line

of the regulator

I = clearance to service regulator vent outlet [*72" (182.9 cm)

minimum]

J = clearance to non-mechanical air supply inlet to building

or the combustion air inlet to any other fireplace

[6" (15 cm) min. for 10,000 Btu or less; 9" (23 cm) in US

if between 10,000 and 50,000, 12" (30 cm) in Canada

if between 10,000 and 100,000; 12" (30 cm) in US if

greater than 50,000, 36" (91 cm) in Canada if greater

than 100,000]

K = clearance to a mechanical air supply inlet [*In Canada,

6 ft. (1.83m) minimum; In US 3 ft. (91 cm) above if within

10 ft. (3 m) horizontally]

L = † clearance above paved side-walk or a paved driveway

located on public property [*84" (213.3 cm) minimum]

M = clearance under veranda, porch, deck

[*12" (30.5 cm) minimum ‡]

N = clearance above a roof shall extend a minimum of

24" (61 cm) above the highest point when it passes

through the roof surface and any other obstruction within

a horizontal distance of 18" (45.7 cm)

† vent shall not terminate directly above a side-walk or paved driveway which is located between two

single family dwellings and serves both dwellings*

‡ only permitted if veranda, porch, deck or balconey is fully open on a minimum of 2 sides beneath the floor*

* as specified in CAN/CSA B149 (.1 or .2) Installation Codes (1991) for Canada and U.S.A.

Note: Local codes or regulations may require different clearances

A = 6" (15.2 cm)

Inside Corner

B = 6" (15.2 cm)

C = Maximum depth of 48" (121.9 cm)

for recessed location

D = Minimum width for back wall of

recessed location -

Combustible - 38" (965 mm)

Noncombustible - 24" (61 cm)

E = Clearance from corner in

recessed location-

Combustible - 6" (15.2 cm)

Noncombustible - 2" (5.1 cm)

Outside Corner Recessed Location

G = 12" (30.5 cm) minimum clearance

Balcony with No Side Wall

Combustible &

Noncombustible

H = 24" (61 cm)

J = 20" (50.8 cm)

Balcony with Perpendicular Side Wall

Termination Clearances for Buildings with Combustible and Noncombustible Exteriors

Openable

www.desatech.com

116235-01K 9

VENTING INSTALLATION

NOTICE: Failure to follow these in-

structions will void the warranty.

NOTICE: Do not seal termination

cap to vent pipe. Cap must be

removable for vent inspection

and maintenance.

INSTALLATION PRECAUTIONS

• Wear gloves and safety glasses for pro-

tection.

• Use extreme caution when using ladders

or when on roof tops.

• Be aware of electrical wiring locations in

walls and ceilings.

The following actions will void the warranty

on your venting system:

• Installation of any damaged venting com-

ponent.

• Unauthorized modication of the venting sys-

tem (Do not cut or alter vent components).

• Installation of any component part not

manufactured or approved by DESA Heat-

ing, LLC.

• Installation other than as instructed by

these instructions.

WARNING: This gas replace

and vent assembly must be

vented directly to the outside.

The venting system must NEVER

be attached to a chimney serv-

ing a separate solid fuel burning

appliance. Each direct-vent gas

appliance must use a separate

vent system. Do not use com-

mon vent systems.

WARNING: Vent pipe air

space clearances to combus-

tibles are 1" on all sides except

on the horizontal sections,

which require 2" clearances

from the top of the pipe. Where

the termination cap penetrates

a combustible wall, 1" air space

clearance is required.

NOTICE: Read these instruc-

tions completely before attempt-

ing installation.

These models are tested and approved for

use with DESA Heating, LLC (direct-vent) pipe

components and terminations.

The venting system must terminate on the

outside of the structure and can not be at-

tached to a chimney or ue system serving a

separate solid fuel or gas burning appliance.

A direct-vent appliance must have its own

venting system. DO NOT common vent this

appliance.

These models are approved to be vented

either horizontally through an outside wall or

vertically through a roof or chase enclosure

using the following guidelines:

• When venting system terminates horizon-

tally on an outside wall, you may install

a standoff if the termination cap is to be

installed directly on a combustible nish

such as vinyl, wood, stucco, etc.

• Never run the vent downward as this may

cause excessive temperatures which could

cause a re.

• Vent pipe air space clearances to com-

bustibles are 1" on all sides except on the

horizontal sections, which requires 2" clear-

ance from the top of the pipe. Where the

termination cap penetrates a combustible

wall, 1" air space clearance is required.

• Snorkel terminations are required when

minimum clearance to grade cannot be

met (see Figure 16 on page 13).

• Have replace and selected vent compo-

nents on hand to help determine the exact

measurements when elbowing or offsetting.

Always use wall restops when penetrating

walls and restops when penetrating ceil-

ings or attic spaces.

• If using a venting conguration of only

horizontal venting with no vertical run, a

1/4" rise for every 12" of run toward the

termination is required.

WARNING: Read all instruc-

tions completely and thoroughly

before attempting installation.

Failure to do so could result in

serious injury, property damage

or loss of life.

www.desatech.com

116235-01K10

INSTALLATION PLANNING

There are two basic types of direct-vent

installation:

• Horizontal Termination

• Vertical Termination

Horizontal Termination Installation

IMPORTANT: Horizontal square terminations

require only inner portion of wall restop. Hori-

zontal installations using round termination

require exterior portion of wall restop (see

Figure 14, page 12).

1. Set replace in its desired location and

determine route your horizontal venting

will take. Do not secure replace until all

venting has been installed. Some instal-

lations require sliding replace in and out

of position to make nal venting connec-

tions. Figures 14 through 18 on pages 12

through 14 show different congurations

for venting with horizontal termination that

will help you decide which application best

suits your installation. Check to see if wall

studs or roof rafters are in the path of your

desired venting route. If they are, you may

want to adjust location of replace.

2. Direct vent pipe sections and components

are designed with special twist-lock con-

nections.

Twist-Lock Procedure: Female ends of

pipes have locking lugs (indentations).

These lugs will slide straight into match-

ing slots on male ends of adjacent pipes.

Push pipe sections together and twist

one section clockwise approximately one-

quarter turn until sections are fully locked

(see Figure 8). Note: Horizontal runs of

vent must be supported every three feet.

Use wall straps for this purpose.

3. Use a 45° elbow to connect venting system

to replace ue collar. The elbow is de-

signed to be twist-locked onto the ue collar

as described in step 2. IMPORTANT: Do

not attempt to alter the conguration of the

elbow by cutting, twisting, bending, etc.

4. Assemble desired combination of pipe

and elbows to replace ue collar. If there

are long portions of venting run, pre-as-

sembled pipe sections may be installed

as subassemblies for convenience.

VENTING INSTALLATION

Continued

Figure 8 - Vent Pipe Connections

Female Locking Lugs

Male

Slots

(Framing

Detail)

" Inside Framing

Vent

pening

Combustible Wall

Vent Opening

Noncombustible Wall

Figure 9 - Vent Opening Requirements

Center of

Hole

5. Carefully determine location where vent

pipe assembly will penetrate outside wall.

Center of hole should line up with center

line of horizontal vent pipe. Mark wall for a

" x 11

" square hole. Cut and frame

square hole in exterior wall where vent will

be terminated. If wall being penetrated is

constructed of noncombustible material,

such as masonry block or concrete, a 8

" hole with zero clearance is acceptable

(see Figure 9).

www.desatech.com

116235-01K 11

VENTING INSTALLATION

Continued

WARNING: Do not recess

vent termination into any wall.

This will cause a re hazard.

6. Noncombustible Exterior Wall: Position

horizontal vent cap in center of 8

" round

hole and attach to exterior wall with four

wood screws provided. Before attaching

vent cap to exterior wall, run a bead of

non-hardening mastic (pliable sealant)

around outside edges to make a seal

between it and the outside wall.

Note: Four wood screws provided should

be replaced with appropriate fasteners for

stucco, brick, concrete or other types of

sidings.

Combustible Exterior Wall: For vinyl

siding, stucco or wood exteriors, a siding

standoff may be installed between vent

cap and exterior wall. Siding standoff

prevents excessive heat from damaging

siding materials. Siding material must be

cut to accommodate standoff. Bolt vent

cap to standoff. Apply non-hardening

mastic around outside edge of standoff.

Position standoff/cap assembly in center

of the 11

" square hole and attach to

exterior wall with wood screws provided

(see Figure 11). Siding standoff must sit

ush against exterior fascia material.

7. Connecting Vent Cap with Horizontal

Vent Pipe: Slide wall restop over vent

pipe before connecting horizontal run to

vent cap (see Figure 12).

Carefully move replace, with vent as-

sembly attached, toward wall and insert

vent pipe into horizontal termination. Pipe

overlap should be a minimum of 1

" (see

Figure 13, page 12).

Slide wall restop against interior wall

surface and attach with screws provided.

See Figure 13, page 12, for horizontal

termination details.

Place replace into position and shim with

noncombustible material if needed. Nail or

screw side anges to framing to secure

unit in place. IMPORTANT: Make sure re-

place is level before securing. If replace

is not level it will not work properly.

Figure 10 - Installing Horizontal Vent Cap

(Noncombustible Exterior)

Wood Screw

Vent Cap

Figure 11 - Installing Siding Standoff

(Combustible Exterior Wall)

Cut Siding Away to

Fit Standoff

Wood

Screw

Screws

Standoff

Vent

Cap

Apply Mastic to

All Four Sides

Vent Cap

(Horizontal

Termination)

Interior Wall

Surface

Wall

Firestop

Horizontal

Vent Pipe

Figure 12 - Connecting Vent Cap with

Horizontal Vent Pipe

Screw

Apply Mastic on

All Four Sides

www.desatech.com

116235-01K12

VENTING INSTALLATION

Continued

Figure 13 - Typical Horizontal

Termination Cap Mounting with

Additional Siding Standoff Installed

Siding Standoff

Screws

High Wind

Termination

Apply

Mastic to

Outside

Edge of

Standoff

Exterior Wall with Vinyl Siding

" x 11

Framed Opening

Maintain 1"

Minimum Air

Space Around

Outer Pipe When

Penetrating a Wall

Minimum Pipe

Overlap 1

Wall

Firestop

Direct-Vent

Pipe

Horizontal Termination Congurations

Figures 14 through 18 show different con-

gurations and alternatives for venting with

horizontal termination. Each gure includes

a chart with critical minimum and maximum

dimensions which MUST be met. IMPOR-

TANT: If using a venting conguration of only

horizontal venting with no vertical run, a 1/4"

rise for every 12" of run toward the termina-

tion is required.

NOTICE: Do not seal termination

cap to vent pipe. Cap must be

removable for vent inspection

and maintenance.

WARNING: Never run vent

downward as this may cause

excessive temperatures which

could cause a re. Operation of

improperly installed and main-

tained venting system could

result in serious injury, property

damage or loss of life.

GROUND FLOOR INSTALLATION

Recommended Applications:

• Installation using cabinet surrounds

• Through the wall using round or square

termination

(up to 12" adjustable pipe)

• NOT FOR CORNER INSTALLATION

Horizontal

High Wind

Square

Termination

Wall Firestop

45° Elbow

Figure 14 - Horizontal Termination

Conguration for Square or Round

Terminations

45° Elbow

Wall

Firestop

Horizontal

Round

Termination

Exterior Portion of

Wall Firestop (Round

Termination Only)

Adjustable

Pipe 12" Max.

Round Termination

* If installing this replace at altitudes of 4000

feet and above, it is recommended that an

additional vertical height of 6" be added to

the vent system.

Square Termination

Vertical (V) Horizontal (H)

" min. 17" max.

www.desatech.com

116235-01K 13

CORNER INSTALLATION

Recommended Applications:

• Corner ground oor installation

• Ground oor installation where pipe vents

horizontally through wall (over 12" horizon-

tal pipe)

• Basement installation where one foot

clearance from ground to termination is

possible

VENTING INSTALLATION

Continued

Figure 15 - Horizontal Termination Conguration for Corner Installation Using One

90° Elbow

Square

Termination

Wall

Firestop

Not to Exceed (H) Limits

As Required

for (V), See

Chart for

Pipe Section

Required

45° Elbow

90°

Elbow

90° Elbow

Square

Termination

Wall

Firestop

45° Elbow

12" Min.

Not to Exceed

(H) Limits

SNORKEL TERMINATION INSTALLATION

Recommended Applications:

• Installations requiring a vertical rise on building exterior

• Any installation using snorkel termination to achieve one foot above ground

Snorkel terminations are available for installations requiring a vertical rise on the exterior of

the building. If installing snorkel termination below grade, you must provide proper drainage

to prevent water from entering snorkel termination (see Figure 16). Do not back ll around

snorkel termination.

Snorkel Termination

12"

Min.

Snorkel Termination

Wall

Firestop

90° Elbow

45° Elbow

Figure 16 - Snorkel Termination Congurations for Below Ground Installation

Snorkel Termination

Adequate

Drainage

12" Min.

Required

Vertical (V) Vertical Pipe Horizontal (H)

*43

" min. None 30" max.

" min. 1 ft. 48" max.

" min. 2 ft. 60" max.

" min. 3 ft. 84" max.

" min. 4 ft. 20' max.

* Ground Floor Corner Venting

www.desatech.com

116235-01K14

VENTING INSTALLATION

Continued

Figure 17 - Horizontal Termination Conguration for Venting Using Two 90° Elbows

45° Elbow

HORIZONTAL SYSTEM INSTALLATION USING TWO 90° ELBOWS

The following congurations show the minimum vertical rise requirements

for a horizontal system using two 90° elbows.

Figure 18 - Horizontal Termination Conguration for Venting Using Two 90° Elbows

with Termination at 90° with Fireplace

45° Elbow

Venting with Two 90° Elbows

Vertical (V) Horizontal (H

)

Horizontal (H

) +

Horizontal (H

)

5' min. 2' max. 6' max.

6' min. 4' max. 12' max.

7' min. 6' max. 18' max.

8' min. 8' max. 20' max.

20' max. 8' max. 20' max.

Venting with Two 90° Elbows

Vertical (V)

Horizontal (H

) +

Horizontal (H

)

5' min. 6' max.

6' min. 12' max.

7' min. 18' max.

8' min. 20' max.

20' max. 20' max.

www.desatech.com

116235-01K 15

INSTALLATION FOR VERTICAL

TERMINATION

Note: Vertical restrictor must be installed in

all vertical installations.

1. Determine route your vertical venting

will take. If ceiling joists, roof rafters or

other framing will obstruct venting system,

consider an offset (see Figure 19) to avoid

cutting load bearing members. Note: Pay

special attention to these installation

instructions for required clearances (air

space) to combustibles when passing

through ceilings, walls, roofs, enclosures,

attic rafters, etc. Do not pack air spaces

with insulation. Also note maximum

vertical rise of venting system and any

maximum horizontal offset limitations.

2. Set replace in desired location. Drop a

plumb line down from ceiling to position

of replace exit ue. Mark center point

where vent will penetrate ceiling. Drill a

small locating hole at this point.

Drop a plumb line from inside of roof to

locating hole in ceiling. Mark center point

where vent will penetrate roof. Drill a small

locating hole at this point.

Flat Ceiling Installation

1. Cut a 11

" square hole in ceiling using

locating hole as a center point. Opening

should be framed to 11

" x 11

" inside

dimensions, as shown in Figure 9 on page

10 using framing lumber the same size as

ceiling joists. If area above ceiling is an

insulated ceiling or an attic, nail restop

from top side. This prevents loose insula-

tion from falling into required clearance

space. If area above ceiling is a living

space, install restop below framed hole.

Firestop should be installed with no less

than three nails per side (see Figure 20).

2. Assemble desired lengths of pipe and

elbows necessary to reach from replace

ue up through restop. Be sure all pipe

and elbow connections are fully twist-

locked (see Figure 8, page 10).

3. Cut a hole in roof using the locating hole

as a center point. (Cover any exposed

open vent pipes before cutting hole in

roof.) The 11

" x 11

" hole must be

measured on the horizontal; actual length

may be larger depending on pitch of roof.

There must be a 1" clearance from vent

pipe to combustible materials. Frame

opening as shown in Figure 9, page 10.

4. Connect a section of pipe and extend up

through hole.

Note: If an offset is needed to avoid

obstructions, you must support vent pipe

every 3 feet. Use wall straps for this pur-

pose (see Figure 19, page 15). Whenever

possible, use 45° elbows instead of 90°

elbows. A 45° elbow offers less restriction

to the ow of ue gases and intake air.

VENTING INSTALLATION

Continued

Figure 19 - Offset with Wall Strap and 45°

Elbows

45° Elbow

Wall Strap

Roof Flashing

Ceiling Firestop

Figure 20 - Installing Firestop

If area above is a living space, install

restop below framed hole.

If area above is an attic or insulated area,

install restop above framed hole.

www.desatech.com

116235-01K16

5. Place ashing over pipe section(s) ex-

tending through roof. Secure base of

ashing to roof and framing with roong

nails. Be sure roong material overlaps

top edge of ashing as shown in Figure

19, page 15. There must be a 1" clearance

from vent pipe to combustible materials.

6. Continue to add pipe sections until height

of vent cap meets the minimum building

code requirements described in Figure

7 on page 8. Note: You must increase

vent height for steep roof pitches. Nearby

trees, adjoining rooines, steep pitched

roofs and other similar factors may cause

VENTING INSTALLATION

Continued

Figure 21 - Vertical Venting

Conguration Using Two 90° Elbows

with Two Horizontal Runs (Vertical

Round High Wind Termination Shown)

45° Elbow

Figure 22 - Vertical Venting

Conguration Using One 90° Elbow

(Vertical Round High Wind Termination

Shown)

45° Elbow

poor draft or down-drafting in high winds.

Increasing vent height may solve this

problem.

7. Twist-lock vent cap onto last section of

vent pipe.

Note: If vent pipe passes through any occu-

pied areas above rst oor, including storage

spaces and closets, you must enclose pipe.

You may frame and sheetrock enclosure with

standard construction material. Make sure

and meet minimum allowable clearances

to combustibles. Do not ll any required air

spaces with insulation.

Vertical Termination Congurations

Figures 21 through 24 show four different

congurations for vertical termination.

Venting with Two 90° Elbows

Vertical (V)

Horizontal (H

) +

Horizontal (H

)

5' min. 2' max.

6' min. 4' max.

7' min. 6' max.

8' min. 8' max.

20' max. 8' max.

Note: Install restrictor

into inner collar of

replace as shown.

Venting with One 90° Elbow

Vertical (V) Horizontal (H)

5' min. 2' max.

6' min. 4' max.

7' min. 6' max.

8' min. 8' max.

20' max. 8' max.

Note: Install restrictor into

inner collar of replace as

shown.

www.desatech.com

116235-01K 17

VENTING INSTALLATION

Continued

Note: Vertical (V

) + Vertical (V

) = 40' max.

Figure 23 - Vertical Venting

Conguration Using Two 90° Elbows

(Vertical Round High Wind Termination

Shown)

45° Elbow

Vertical Venting

V = 40' max.

Figure 24 - Vertical Venting

Conguration With No Horizontal Run

(Vertical Round High Wind Termination

Shown)

45° Elbow

HIGH ALTITUDE INSTALLATION

Your DESA Heating, LLC direct-vent replace

has been tested and approved for elevations

from 0-2000 feet (USA) and elevations from

0-4500 feet (Canada).

When installing this replace at an elevation

above 2000 feet (in the USA), you may need

to decrease the input rating by changing the

existing burner orice to a smaller size. Re-

duce input 4% for each 1000 feet above sea

level. Check with your local gas company for

proper orice size identication.

When installing this replace at an elevation

above 4500 feet (in Canada), check with local

authorities.

Consult your local gas company to help deter-

mine the proper orice for your location.

For assistance with any high altitude installa-

tion contact DESA Heating, LLC’s Customer

Service Department at 1-866-672-6040.

Note: Install

restrictor into inner

collar of replace

as shown.

Venting with Two 90° Elbows

Vertical (V

) Horizontal (H)

5' min. 6' max.

6' min. 12' max.

7' min. 18' max.

8' min. 20' max.

Note: Install restrictor

into inner collar of

replace as shown.

www.desatech.com

116235-01K18

PARTS LIST FOR VENTING KITS

AND COMPONENTS

DESA (5"/8") Pipe & Vent Kits

Number Description

P58-6 6" Section Double Wall Pipe,

Galvanized

P58-12 12" Section Double Wall Pipe,

Galvanized

P58-24 24" Section Double Wall Pipe,

Galvanized

P58-36 36" Section Double Wall Pipe,

Galvanized

P58-48 48" Section Double Wall Pipe,

Galvanized

PA58-712 Adjustable 7"-12" Section Double

Wall Pipe, Galvanized

E58-45 45° Elbow, Galvanized

E58-90 90° Elbow, Galvanized

VKG-58 Ground Floor Vent Kit,

Galvanized (Includes: 45° Elbow,

7"-12" Adjustable Pipe, Wall

Firestop, Horizontal Square

Termination, 16 Screws)

VKB-58 Basement Vent Kit, Galvanized

(Includes: 45° Elbow, 7"-12"

Adjustable Pipe, Wall Firestop,

Horizontal Square Termination,

4' Pipe, 90° Elbow, 20 Screws)

VKS-58 Snorkel Vent Kit, Galvanized

(Includes: 45° Elbow, 7"-12"

Adjustable Pipe, Wall Firestop,

36" Snorkel Termination, 4' Pipe,

1' Pipe, 90° Elbow, 26 Screws)

VKR-58 Roof Vent Kit, Galvanized

(Includes: 45° Elbow, 7"-12"

Adjustable Pipe, Flue Restrictor,

Vertical High Wind Termination,

2' Pipe, 4' Pipe, Wall Firestop,

Storm Collar, Roof Flashing

[0/12 - 6/12], 26 Screws)

VKC-58 Corner Vent Kit, Galvanized

(Includes 45° Elbow, 7"-12"

Adjustable Pipe, Wall Firestop,

Horizontal Termination, 6" Pipe,

90° Elbow, 18 Screws)

HHTK-58 High Wind Round Horizontal

Termination Kit (Includes Round

Termination, Wall Firestop, 45°

Elbow)

VENTING INSTALLATION

Continued

Number Description

HHT-58 High Wind Round Horizontal

Termination Kit, Galvanized

HTS-58 Horizontal Square Termination,

Galvanized

HTKS-58 Horizontal Square Termination

Kit (Includes: Square

Termination, Wall Firestop, 45°

Elbow)

VT-58 Vertical Round Termination,

Galvanized

ST-58-14 14" Snorkel Termination,

Galvanized

ST-58-36 36" Snorkel Termination,

Galvanized

SC-58 Storm Collar, Galvanized

WF-58 Wall Firestop, Galvanized

RF-58-6 Roof Flashing - 0 to 6/12 Pitch,

Galvanized

RF-58-12 Roof Flashing - 6/12 to 12/12

Pitch, Galvanized

VR-58 Vertical Restrictor, Galvanized

S-58 Vinyl Siding Standoff, Galvanized

WS-58 Wall Strap

CS-58 Cathedral Ceiling Support

FP-58 Firestop Plate

SF-58 Stucco Flashing - For use with

HTS-58

RF-58 Flat Roof Flashing

PF58-927 Flex Pipe Section 9" to 24"

PF58-1236

Flex Pipe Section 12" to 36"

PF58-1854

Flex Pipe Section 18" to 54"

VKF58-927

Flex Kit (Includes Flex Pipe Wall

Section 9" to 27", Firestop and

Horizontal Square Termination)

www.desatech.com

116235-01K 19

FIREPLACE

INSTALLATION

CHECK GAS TYPE

Use proper gas type for the replace unit you

are installing. If you have conicting gas types,

do not install replace. See retailer where you

purchased the replace for proper replace

according to your gas type or to purchase gas

conversion kit (see Accessories, page 35).

INSTALLING OPTIONAL BLOWER

ACCESSORIES

NOTICE: If installing blower in

an existing replace with gas

connections, shut off gas sup-

ply and disconnect heater from

gas supply. Contact a qualied

service person to do this.

WARNING: If there is a duplex

electrical outlet installed in the

right side of the bottom of the

replace base area, be sure that

the electrical power to the outlet

is turned off before proceeding

with blower installation. Failure

to do this may result in serious

injury.

Model BK Installation

Follow all instructions provided in blower

accessory kit.

1. Attach power cord to blower motor by

rmly pushing two female terminals at end

of power cord onto two spade terminals

on blower motor (see Figure 25).

2. Attach green ground wire from power

cord to blower housing using screw pro-

vided (see Figure 25). Tighten screws

securely.

3. Place blower against lower rear wall of

rebox outer wrapper with exhaust port

directed upward. Blower will t inside back

opening and be held in position against

back wall by magnets (see Figure 25).

4. Be certain that all wire terminals are

securely attached to terminals on blower

motor and that screw retaining green

ground wire is tight.

5. Mount speed control box to switch bracket

by placing plastic control shaft forward

through round opening in switch bracket

(see Figure 26).

6. While supporting speed control, secure

control shaft with lock nut by pushing

and turning lock nut with pliers clockwise

until it is tight against front panel. Place

provided control knob on shaft.

7. Turn on power to duplex outlet if previously

turned off per warning in column 1.

8. Plug in blower power cord.

a. If your rebox is installed as a free-

standing unit with an accessory mantel,

determine whether power cord will exit

left side or right side of rebox. Route

power cord through exit hole and plug

power cord into a wall receptacle near

rebox.

b. If your rebox installation is recessed

and/or pre-wired, plug power cord into

duplex outlet provided. Refer to your

rebox owner’s manual for instructions

on wiring duplex outlet.

Blower Location

Side View

Figure 25 - Blower Model BK

Magnetic

Strips

Exhaust Port

Screw

Green

Ground

Wire

Spade

Terminals

Lower Firebox

Cavity

Figure 26 - Attaching Speed Control to

Firebox

Speed Control

Control Shaft

Locknut

Control

Knob

Switch

Bracket

Blower

Plug-In

Duplex Outlet (Located

beneath rebox oor

against lower right

outside wall)

www.desatech.com

116235-01K20

CAUTION: Never touch the

blower wheel while in operation.

9. Check to make sure that power cord is

completely clear of blower wheel and

that there are no foreign objects in blower

wheel. Turn blower on and check for op-

eration. Turn blower off by turning knob

fully counterclockwise before continuing.

10. Peel off backing paper and stick supplied

wiring diagram decal on rebox bottom

approximately 12" in front of blower (see

Figure 27).

Figure 27 - Location of Wiring Diagram

Decal (Model May Vary From Illustration)

Wiring Diagram Decal

12" in Front of Blower

FIREPLACE INSTALLATION

Continued

Model BKT Installation

Note: When installing BKT thermostati-

cally-controlled blower, you must rst secure

thermal switch bracket to blower if it has not

already been factory installed.

1. Place green ground wire with ring ter-

minal between bottom hole on thermal

switch bracket and top ear hole on blower

assembly. Insert Phillips screw into all

three pieces and tighten securely (see

Figure 28).

2. Connect wire harness and power cord

terminals. Connect blue jumper wire to

blower motor terminal and right side termi-

nal of thermal switch. Connect black wire

to left side of thermal switch and white

wire to other remaining blower motor

terminal.

Note: Power cord outer insulation sleeve may

have to be stripped slightly to allow enough

wire length to reach and make all connec-

tions. DO NOT trim excessive length away.

Enable just enough to make all connections

securely.

3. Place blower against lower rear wall of

rebox outer wrapper with exhaust port di-

rected upward and thermodisc positioned

up near fireplace bottom. Thermodisc

must be oriented near replace bottom

as shown in Figure 28 in order to sense

temperature and properly operate. Blower

will be held in position against back wall

by magnets incorporated onto blower

housing (see Figure 28).

4. Be certain that all wire terminals are

securely attached to terminals on blower

motor and thermal switch and that screw

for thermodisc bracket and green ground

wire is tight.

5. Mount speed control box against mount-

ing plate provided in lower fireplace

cavity by placing plastic control shaft

forward through round hole (see Figure

26, page 19).

6 While supporting speed control, secure

control shaft with lock nut by pushing and

turning lock nut with pliers clockwise until

it is tight against mounting plate. Place

provided control knob on shaft (see Figure

26, page 19).

Thermodisc

Figure 28 - Blower Model BKT

Air Flow Direction

Route BKT Blower

Through This Area

Magnets

Blower

Location

Side View Firebox Bottom

Black

Wire

Phillips

Screw

Blue Wire

Ring Terminal

on Green Wire

White Wire

Thermal

Switch

Thermal

Switch

Bracket

Power Cord

Air Flow

Direction

Magnetic

Strips

Page is loading ...

FMI DVM36VNE Owner's manual

Brand: FMI

Model: DVM36VNE

Category: Fireplaces

Type: Owner's manual

Download PDF

report

FMI DVM36VNE Owner's manual

FMI DVM36VNE Owner's manual

Related papers

Other documents