Roland PROMARS PLUG-OUT Owner's manual

Type
Owner's manual

This manual is also suitable for

Roland PROMARS PLUG-OUT: Analog modeling synthesizer plug-in that faithfully recreates the sound and behavior of the original Roland PROMARS synthesizer from 1978. With its authentic sound engine, it delivers the same warm, lush, and spacious sounds as the original hardware, making it ideal for creating vintage electronic music, soundtracks, and ambient textures.

Roland PROMARS PLUG-OUT: Analog modeling synthesizer plug-in that faithfully recreates the sound and behavior of the original Roland PROMARS synthesizer from 1978. With its authentic sound engine, it delivers the same warm, lush, and spacious sounds as the original hardware, making it ideal for creating vintage electronic music, soundtracks, and ambient textures.

SYSTEM-100 PLUG-OUT Software Synthesizer Q&A
2015/08/27
Q :
The sound periodically becomes softer or distorted.
A :
If you have not yet activated it, the audio output periodically becomes distorted or reduced in volume,
beginning 10 minutes after you started the PLUG-OUT softwaresynthesizer. And once 14 days have
elapsed since you first started the PLUG-OUT software synthesizer, the audio output periodically
becomes distorted or reduced in volume as soon as you start it.
Once activation is completed, the software synthesizer operates normally.
Q :
On how many computers can I activate the software?
A :
The Plug-Out Software Synthesizer can be activated on a maximum of three computers.
If you've exceeded the maximum number of activations, check the computers that you've registered on
your Roland account service, and deactivate any unneeded activations; then activate the software
again.
Q :
When using the SYSTEM-1 as a control surface in Cubase Series, operating the knobs in the MIXER
section of the SYSTEM-1 causes multiple VST parameters to change, or causes unintended
parameters to change.
A :
The Track Quick Controls settings of Cubase Series can cause specific Track Control Changes to be
converted to automation parameters.
You can avoid this problem by turning the Track Quick Controls function off.
Q :
In the Setting window, the MIDI Input and MIDI Output parameters show [SYSTEM-1 CTRL
(Unconnected)], and I can't choose [SYSTEM-1 CTRL]. (Windows)
A :
Make the following device settings in your DAW.
Cubase Series
1. Open [Devices] - [Device Setup].
2. For the [SYSTEM-1 CTRL] port, clear the check boxes [Visible] and [In All MIDI] for both
MIDI In and MIDI Out.
SONAR X3 Producer
1. Open [Edit] - [Preferences] - [MIDI] - [Device], and clear the check box for the [SYSTEM-1
CTRL] port.
StudioOne 2
1. Open [Studio One] - [Options] - [External Devices].
2. If [SYSTEM-1 CTRL] port is selected for [Receive From] and [Send To], change the
selection to [SYSTEM-1].
Q :
I want to return the patches to their original factory-set condition.
A :
You can import the factory-set patch bank as follows.
1. Download the preset patch bank file from this link and decompress it.
SYSTEM-100 PLUG-OUT Original Preset Patch
2. Using the Plug-Out synthesizer's [Patch Select] screen, import the file from the folder that
you decompressed.
3. The factory-set bank is added.
Copyright (C) 2015 Roland Corporation
  • Page 1 1
  • Page 2 2

Roland PROMARS PLUG-OUT Owner's manual

Type
Owner's manual
This manual is also suitable for

Roland PROMARS PLUG-OUT: Analog modeling synthesizer plug-in that faithfully recreates the sound and behavior of the original Roland PROMARS synthesizer from 1978. With its authentic sound engine, it delivers the same warm, lush, and spacious sounds as the original hardware, making it ideal for creating vintage electronic music, soundtracks, and ambient textures.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI