Grizzly T10883 Owner's manual

Brand: Grizzly

Model: T10883

Category: Vacuum cleaner supplies

Type: Owner's manual

Grizzly T10883 is a powerful machine that can help you with a variety of tasks. With its HEPA filter upgrade kit, it can effectively remove harmful particles from the air, making it ideal for use in workshops, garages, and other industrial settings.

Here are some of the key features and capabilities of the Grizzly T10883:

HEPA filter upgrade kit: The HEPA filter upgrade kit removes 99.97% of particles down to 0.3 microns in size, making it ideal for use in areas where air quality is a concern.
Powerful motor: The Grizzly T10883 is equipped with a powerful motor that provides ample suction for even the most demanding tasks.

Here are some of the key features and capabilities of the Grizzly T10883:

HEPA filter upgrade kit: The HEPA filter upgrade kit removes 99.97% of particles down to 0.3 microns in size, making it ideal for use in areas where air quality is a concern.
Powerful motor: The Grizzly T10883 is equipped with a powerful motor that provides ample suction for even the most demanding tasks.

Model T10883

G0638 Cartridge Filter Replacement

with HEPA Filter Upgrade Kit

Step One:

Remove the filter L-braces from the blower housing, as shown above, by loosening and removing (6) 5/16” x

1” hex bolts, (12) 5/16” flat washers, and (6) 5/16” hex nuts. Remove and set the cartridge filter aside.

Step Two:

Remove the outlet port from the blower housing by loosening and removing (4) 5/16” x 1” hex bolts, (8) 5/16”

flat washers, and (4) 5/16” hex nuts.

Step Three:

Remove the mounting bracket that secures the intake barrel to the upper leg stand by loosening and removing (8)

3/8” x 1-1/4” hex bolts, (16) 3/8” flat washers, and (8) 3/8” nuts. Next, loosen and remove (8) 3/8” x 3/4” hex

bolts, (16) 3/8” flat washers, and (8) 3/8” nuts on the leg stand side. NOTE: Replace each mounting bracket

with the new type one at a time. DO NOT remove all old mounting brackets at once.

Step Four:

After each mounting bracket has been replaced with the new type, make sure to tighten all the bolts and nuts

securely before moving on to the next step.

Step Five:

Attach the rubber gasket to the outlet opening on the blower housing, then attach the outlet connector by

securing and fastening (10) 3/8” x 1” hex bolts, (20) 3/8” flat washers, and (10) 3/8” nuts.!

Step Six:

Assemble the HEPA leg stand, which consists of upper, middle and lower segments. Secure and fasten using (8)

3/8” x 1” hex bolts, (16) 3/8” flat washers, and (8) 3/8” nuts. !

Step Seven:

Attach the HEPA leg stand to the outlet connector, as shown above, by securing and fastening (4) 3/8” x 1” hex

bolts, (8) 3/8” flat washers, and (4) 3/8” nuts. !

Step Eight:

Attach the rubber gasket to the square top of the HEPA filter, as shown above. Attach the filter adapter to the

square top of the HEPA filter with (16) 5/16” x 1” hex bolts and 5/16” flat washers. Tighten and secure all bolts

and nuts.

Step Nine:

Attach the rubber gasket to the outlet opening, then attach the filter adapter with the HEPA filter to the blower

housing with (16) 3/8” x 1” hex bolts, (30) 3/8” flat washers, and (14) 3/8” nuts. Tighten and secure all bolts

and nuts.

Step Ten:

Fit the plastic canister collection bag over the bottom of the HEPA canister filter, and clamp in place with the

metal bag clamp, as shown above.

UPGRADE COMPLETE!

Grizzly T10883 Owner's manual

Brand: Grizzly

Model: T10883

Category: Vacuum cleaner supplies

Type: Owner's manual

Here are some of the key features and capabilities of the Grizzly T10883:

HEPA filter upgrade kit: The HEPA filter upgrade kit removes 99.97% of particles down to 0.3 microns in size, making it ideal for use in areas where air quality is a concern.
Powerful motor: The Grizzly T10883 is equipped with a powerful motor that provides ample suction for even the most demanding tasks.

Download PDF

report

Grizzly T10883 Owner's manual

Grizzly T10883 Owner's manual

Related papers

Other documents