Grizzly T28959 Owner's manual

Brand: Grizzly

Model: T28959

Category: Knife sharpeners

Type: Owner's manual

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#AL20250 PRINTED IN CHINA

V1.03.19

MODEL T28959

ELECTRIC CHAINSAW

SHARPENER

OWNER'S MANUAL

(For models manufactured since 02/19)

This manual provides critical safety instructions on the proper setup,

operation, maintenance, and service of this machine/tool. Save this

document, refer to it often, and use it to instruct other operators.

Failure to read, understand and follow the instructions in this manual

may result in fire or serious personal injury—including amputation,

electrocution, or death.

The owner of this machine/tool is solely responsible for its safe use.

This responsibility includes but is not limited to proper installation in

a safe environment, personnel training and usage authorization,

proper inspection and maintenance, manual availability and compre-

hension, application of safety devices, cutting/sanding/grinding tool

integrity, and the usage of personal protective equipment.

The manufacturer will not be held liable for injury or property damage

from negligence, improper training, machine modifications or misuse.

Some dust created by power sanding, sawing, grinding, drilling, and

other construction activities contains chemicals known to the State

of California to cause cancer, birth defects or other reproductive

harm. Some examples of these chemicals are:

• Lead from lead-based paints.

• Crystalline silica from bricks, cement and other masonry products.

• Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you

do this type of work. To reduce your exposure to these chemicals:

Work in a well ventilated area, and work with approved safety equip-

ment, such as those dust masks that are specially designed to filter

out microscopic particles.

Table of Contents

INTRODUCTION ............................................................................................................................... 2

Contact Info ................................................................................................................................ 2

Manual Accuracy ........................................................................................................................ 2

Identification ............................................................................................................................... 3

Controls & Components ............................................................................................................. 4

Chainsaw Terminology ............................................................................................................... 5

Machine Data Sheet ................................................................................................................... 7

SECTION 1: SAFETY ....................................................................................................................... 8

Safety Instructions for Machinery ............................................................................................... 8

Additional Safety for Chainsaw Sharpeners ............................................................................ 10

SECTION 2: POWER SUPPLY ...................................................................................................... 11

SECTION 3: SETUP ....................................................................................................................... 13

Unpacking ................................................................................................................................ 13

Needed for Setup ..................................................................................................................... 13

Inventory ................................................................................................................................... 13

Site Considerations .................................................................................................................. 14

Bench Mounting ....................................................................................................................... 14

Assembly .................................................................................................................................. 15

Test Run ................................................................................................................................... 16

SECTION 4: OPERATIONS ........................................................................................................... 17

Operation Overview.................................................................................................................. 17

How the Chain Cuts ................................................................................................................. 18

Grinding Wheel Selection ......................................................................................................... 19

Wheel Inspection & Ring Test .................................................................................................. 20

Installing Grinding Wheel ......................................................................................................... 20

Adjusting Top Plate ................................................................................................................. 21

Leading Edge ........................................................................................................................... 21

Sharpening Operation .............................................................................................................. 22

Adjusting Clamp Plate Pressure .............................................................................................. 25

SECTION 5: ACCESSORIES ......................................................................................................... 26

SECTION 6: MAINTENANCE......................................................................................................... 27

Schedule .................................................................................................................................. 27

Cleaning & Protecting .............................................................................................................. 27

Lubrication ................................................................................................................................ 27

Grinding Wheel......................................................................................................................... 27

SECTION 7: SERVICE ................................................................................................................... 28

Troubleshooting ........................................................................................................................ 28

SECTION 8: WIRING ...................................................................................................................... 29

Wiring Safety Instructions ........................................................................................................ 29

Wiring Diagram......................................................................................................................... 30

SECTION 9: PARTS ....................................................................................................................... 31

Main .......................................................................................................................................... 31

WARRANTY & RETURNS ............................................................................................................. 33

-2-

Model T28959 (Mfd. Since 2/19)

We stand behind our machines! If you have ques-

tions or need help, contact us with the information

below. Before contacting, make sure you get the

serial number

and manufacture date from the

machine ID label. This will help us help you faster.

Grizzly Technical Support

1815 W. Battlefield

Springfield, MO 65807

Phone: (570) 546-9663

Email: [email protected]

We want your feedback on this manual. What did

you like about it? Where could it be improved?

Please take a few minutes to give us feedback.

Grizzly Documentation Manager

P.O. Box 2069

Bellingham, WA 98227-2069

Email: [email protected]

Contact Info

We are proud to provide a high-quality owner’s

manual with your new machine!

made every effort to be exact with the

instruc-

tions, specifications, drawings, and photographs

in this manual. Sometimes we make mistakes, but

our policy of continuous improvement also means

that

sometimes the machine

you receive is

slightly different than shown in the manual

If you find this to be the case, and the difference

between the manual and machine leaves you

confused or unsure about something

check our

website for an updated version. W

e post

current

manuals and

manual updates for free

on our web-

site at

www.grizzly.com.

Alternatively, you can call our Technical Support

for help. Before calling, make sure you write down

the

Manufacture Date and Serial Number

from

the machine ID label (see below). This information

is required for us to provide proper tech support,

and it helps us determine if updated documenta-

tion is available for your machine.

Manufacture Date

Serial Number

Manual Accuracy

INTRODUCTION

Model T28959 (Mfd. Since 2/19)

-3-

Identification

To reduce your risk of

serious injury, read this

entire manual BEFORE

using machine.

Become familiar with the names and locations of the controls and features shown below to better understand

the instructions in this manual.

Motor

Chain

Clamp Lever

Base

Depth Stop

Wheel

Shield

Depth Stop Knob

ON/OFF Switch

Swing Arm

Handle

Spring-Loaded

Swing Arm

Chain Holder

Assembly

Chain Holder

Angle Knob

Wheel & Arbor

Guard

Grinding Wheel

-4-

Model T28959 (Mfd. Since 2/19)

Controls &

Components

To reduce your risk of

serious injury, read this

entire manual BEFORE

using machine.

Chain Holder Assembly

Refer to the following figures and descriptions to

become familiar with the basic controls and com-

ponents of this machine. Understanding these

items and how they work will help you understand

the rest of the manual and minimize your risk of

injury when operating this machine.

Figure 1. Chain holder assembly.

A. Clamp Plates: Hold chain in place.

B. Guide Adjustment Controls: Controls how

much to move chain in advancement guide.

C. Advancement Guide: Helps guide chain to

next sharpening position.

D. Chain Holder Angle Knob: Loosen to

change angle of chain holder assembly.

Tighten to lock angle in position.

E. Chain Clamp Lever: Tightens clamp plates.

Depth Stop Assembly

F. Depth Stop Knob Bolt: Rotate clockwise to

reduce cutting depth. Rotate counterclock-

wise to increase cutting depth.

G. Depth Stop Jam Nut: Locks depth knob bolt

in place.

H. Depth Stop: Stops the sharpener at pre-

determined depth based on depth knob bolt

setting.

Figure 2. Depth stop assembly.

Model T28959 (Mfd. Since 2/19)

-5-

Chainsaw

Terminology

Refer to the following descriptions and illustrations

to better understand the chainsaw terminology

used in this manual.

Chain Component Identification: The cutter

links illustrated in Figure 3 do the actual cutting,

while the lower tangs of the drive links keep the

chain riding in the guide bar.

The plain ties connect the links together as they

move and pivot on the rivets.

Left-Hand

Cutter Link

Right-Hand

Cutter Link

Drive Link

Plain

Tie

Hub

Figure 3. Chain component identification.

Chain Pitch

= This Distance/2

Figure 4. Chain pitch.

Chain Gauge: The chain gauge is the thickness

of the drive link tang (see Figure 5) where it fits

into the guide bar groove. The guide bar groove

must match the width of the chain gauge.

Drive Link

Tang

Chain

Gauge

Figure 5. Chain gauge.

The chain pitch is the same for all links in the

chain. The smallest chain pitches for handheld

chainsaws are commonly

⁄4",

⁄8", and 0.325."

Chain Pitch: The distance between any three

consecutive rivet centers divided by 2 is known as

the chain pitch (see Figure 4).

Top Plate: The amount of rake from the top plate

to the side plate is generally 25°–35°. This forms

the leading edge of the cut (see Figure 6).

Top Plate Leading Edge: The top plate leading

edge (see Figure 6) is a chisel-like downward

bevel on the underside of the top plate that usu-

ally is 60°. This edge removes wood chips from

the kerf.

Top Plate

Leading

Edge

(Top View) (Side View)

Top Plate

Side Plate

Figure 6. Cutter link top plate.

-6-

Model T28959 (Mfd. Since 2/19)

Side Plate Tip: The ground angle of the side

plate is instrumental in forming the cutting point

between the side and top plates. This angle is

typically 60° (see Figure 7).

Gullet: The gullet (see Figure 7) provides a

space for the wood chips so they can be removed

by the top plate.

Side Plate

Tip

Gullet

Figure 7. Side plate leading edge and gullet.

Clearance: This is the amount that the top plate

angles down from the top plate leading edge to the

rear of the cutter link (see Figure 8). Clearance

allows the cutter link to pivot up into the wood and

then down again.

Clearance

Figure 8. Clearance.

Left- & Right-Hand Cutters: Chainsaws have

left- and right-hand cutter links that together make

the cut. The sharpener must be set up differently

when sharpening left- and right-hand cutters

(see Figure 9), because the angles on the cutters

are reversed. It is important to clearly identify the

orientation of the cutter before sharpening it.

Left-Hand

Cutter

Right-Hand

Cutter

Direction of Chain Travel

Figure 9. Identification of left- and right-hand

cutters.

Model T28959 (Mfd. Since 2/19)

-7-

Machine Data Sheet

Page 1 of 2 Model T28959

MODEL T28959

ELECTRIC CHAINSAW SHARPENER

Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901

Product Dimensions:

Weight ............................................................................................................................................................................... 6 lbs.

Width (side-to-side) x Depth (front-to-back) x Height .................................................................................11 x 13-1/2 x 12 in.

Footprint (Length/Width) ..........................................................................................................................................9-1/2 x 5 in.

Shipping Dimensions:

Type ................................................................................................................................................................... Cardboard Box

Content .......................................................................................................................................................................... Machine

Weight ................................................................................................................................................................................ 7 lbs.

Length x Width x Height .........................................................................................................................................11 x 8 x 7 in.

Must Ship Upright .................................................................................................................................................................. No

Electrical:

Power Requirement ........................................................................................................................ 120V, Single-Phase, 60 Hz

Full-Load Current Rating ..................................................................................................................................................... 0.6A

Minimum Circuit Size ........................................................................................................................................................... 15A

Connection Type ..................................................................................................................................................... Cord & Plug

Power Cord Included ............................................................................................................................................................Yes

Power Cord Length ...............................................................................................................................................................6 ft.

Power Cord Gauge ....................................................................................................................................................... 18 AWG

Included Plug Type ..............................................................................................................................................................1-15

Switch Type ............................................................................................................................................. ON/OFF Push Button

Motor:

Main

Horsepower ...............................................................................................................................................72W (1/10 HP)

Phase .......................................................................................................................................................... Single-Phase

Amps ......................................................................................................................................................................... 0.6A

Speed ...............................................................................................................................................................5000 RPM

Type ....................................................................................................................................................................Universal

Power Transfer ........................................................................................................................................................ Direct

Bearings ......................................................................................................................Sealed & Permanently Lubricated

Main Specifications:

Operation Info

Chain Pitch .................................................................................................................................1/4, 0.325, 3/8, 0.404 in.

Chain Gauge Capacity ........................................................................................................................... 0.050 - 0.070 in.

Vise Angles .................................................................................................................................................0-30 deg. L/R

Wheel Type .........................................................................................................................................................Abrasive

Wheel Material ..................................................................................................................................Corundum, 100 Grit

Wheel Dimensions ..............................................................................................................4-1/4 in. Dia. x 3/16 in. Thick

Wheel Speed ....................................................................................................................................................5000 RPM

Wheel Bore Max. Diameter .....................................................................................................................................7/8 in.

Max. Wheel Diameter ...........................................................................................................................................4-1/4 in.

Max. Wheel Thickness ..........................................................................................................................................3/16 in.

-8-

Model T28959 (Mfd. Since 2/19)

ELECTRICAL EQUIPMENT INJURY RISKS.

You can be shocked, burned, or killed by touching

live electrical components or improperly grounded

machinery. To reduce this risk, only allow qualified

service personnel to do electrical installation or

repair work, and always disconnect power before

accessing or exposing electrical equipment.

DISCONNECT POWER FIRST.

Always discon-

nect machine from power supply BEFORE mak-

ing adjustments, changing tooling, or servicing

machine. This prevents an injury risk from unin-

tended startup or contact with live electrical com-

ponents.

EYE PROTECTION. Always wear ANSI-approved

safety glasses or a face shield when operating or

observing machinery to reduce the risk of eye

injury or blindness from flying particles. Everyday

eyeglasses are NOT approved safety glasses.

OWNER’S MANUAL. Read and understand this

owner’s manual BEFORE using machine.

TRAINED OPERATORS ONLY. Untrained oper-

ators have a higher risk of being hurt or killed.

Only allow trained/supervised people to use this

machine. When machine is not being used, dis-

connect power, remove switch keys, or lock-out

machine to prevent unauthorized use—especially

around children. Make your workshop kid proof!

DANGEROUS ENVIRONMENTS. Do not use

machinery in areas that are wet, cluttered, or have

poor lighting. Operating machinery in these areas

greatly increases the risk of accidents and injury.

MENTAL ALERTNESS REQUIRED. Full mental

alertness is required for safe operation of machin-

ery. Never operate under the influence of drugs or

alcohol, when tired, or when distracted.

For Your Own Safety, Read Instruction

Manual Before Operating This Machine

The purpose of safety symbols is to attract your attention to possible hazardous conditions.

This manual uses a series of symbols and signal words intended to convey the level of impor-

tance of the safety messages. The progression of symbols is described below. Remember that

safety messages by themselves do not eliminate danger and are not a substitute for proper

accident prevention measures. Always use common sense and good judgment.

Indicates a potentially hazardous situation which, if not avoided,

MAY result in minor or moderate injury. It may also be used to alert

against unsafe practices.

Indicates a potentially hazardous situation which, if not avoided,

COULD result in death or serious injury.

Indicates an imminently hazardous situation which, if not avoided,

WILL result in death or serious injury.

Alerts the user to useful information about proper operation of the

machine to avoid machine damage.

NOTICE

Safety Instructions for Machinery

SECTION 1: SAFETY

Model T28959 (Mfd. Since 2/19)

-9-

WEARING PROPER APPAREL. Do not wear

clothing, apparel or jewelry that can become

entangled in moving parts. Always tie back or

cover long hair. Wear non-slip footwear to reduce

risk of slipping and losing control or accidentally

contacting cutting tool or moving parts.

HAZARDOUS DUST. Dust created by machinery

operations may cause cancer, birth defects, or

long-term respiratory damage. Be aware of dust

hazards associated with each workpiece mate-

rial. Always wear a NIOSH-approved respirator to

reduce your risk.

HEARING PROTECTION. Always wear hear-

ing protection when operating or observing loud

machinery. Extended exposure to this noise

without hearing protection can cause permanent

hearing loss.

REMOVE ADJUSTING TOOLS. Tools left on

machinery can become dangerous projectiles

upon startup. Never leave chuck keys, wrenches,

or any other tools on machine. Always verify

removal before starting!

USE CORRECT TOOL FOR THE JOB. Only use

this tool for its intended purpose—do not force

it or an attachment to do a job for which it was

not designed. Never make unapproved modifica-

tions—modifying tool or using it differently than

intended may result in malfunction or mechanical

failure that can lead to personal injury or death!

AWKWARD POSITIONS. Keep proper footing

and balance at all times when operating machine.

Do not overreach! Avoid awkward hand positions

that make workpiece control difficult or increase

the risk of accidental injury.

CHILDREN & BYSTANDERS. Keep children and

bystanders at a safe distance from the work area.

Stop using machine if they become a distraction.

GUARDS & COVERS. Guards and covers reduce

accidental contact with moving parts or flying

debris. Make sure they are properly installed,

undamaged, and working correctly BEFORE

operating machine.

FORCING MACHINERY. Do not force machine.

It will do the job safer and better at the rate for

which it was designed.

NEVER STAND ON MACHINE. Serious injury

may occur if machine is tipped or if the cutting

tool is unintentionally contacted.

STABLE MACHINE. Unexpected movement dur-

ing operation greatly increases risk of injury or

loss of control. Before starting, verify machine is

stable and mobile base (if used) is locked.

USE RECOMMENDED ACCESSORIES. Consult

this owner’s manual or the manufacturer for rec-

ommended accessories. Using improper acces-

sories will increase the risk of serious injury.

UNATTENDED OPERATION. To reduce the

risk of accidental injury, turn machine OFF and

ensure all moving parts completely stop before

walking away. Never leave machine running

while unattended.

MAINTAIN WITH CARE. Follow all maintenance

instructions and lubrication schedules to keep

machine in good working condition. A machine

that is improperly maintained could malfunction,

leading to serious personal injury or death.

DAMAGED PARTS. Regularly inspect machine

for damaged, loose, or mis-adjusted parts—or

any condition that could affect safe operation.

Immediately repair/replace BEFORE operating

machine. For your own safety, DO NOT operate

machine with damaged parts!

MAINTAIN POWER CORDS. When disconnect-

ing cord-connected machines from power, grab

and pull the plug—NOT the cord. Pulling the cord

may damage the wires inside. Do not handle

cord/plug with wet hands. Avoid cord damage by

keeping it away from heated surfaces, high traffic

areas, harsh chemicals, and wet/damp locations.

EXPERIENCING DIFFICULTIES. If at any time

you experience difficulties performing the intend-

ed operation, stop using the machine! Contact our

Technical Support at (570) 546-9663.

-10-

Model T28959 (Mfd. Since 2/19)

Additional Safety for Chainsaw Sharpeners

Serious injury or death can occur from getting fingers, hair, or clothing entangled in rotating

or moving parts. Workpieces can be ejected by sharpener, striking operator or bystanders. To

minimize risk of injury, anyone operating this machine MUST completely heed hazards and

warnings below.

TOP PLATE LENGTH. If the length of the cutter

top plate from the leading edge to the rear of the

cutter link is less than

⁄4" after sharpening, there

is a high risk that this link will break during the

cutting operation. Always inspect the cutter after

sharpening and replace it or the chain if in doubt.

CHAIN SPECIFICATIONS. If the chain is incor-

rectly sharpened, the links could break dur-

ing use and send flying debris at the operator

or bystanders. Always make sure the sharp-

ener setup agrees with the chain manufacturer’s

specifications.

VOLATILE/FLAMMABLE MATERIALS. The

grinding wheel produces sparks when sharpen-

ing the chain that could cause volatile materials to

catch fire or explode. Never use flammable mate-

rials to clean the chain (such as gasoline, kero-

sene, or mineral spirits) and never operate the

sharpener near volatile or flammable materials.

READ AND FOLLOW all safety instructions in the

chainsaw owner’s manual.

CHAIN INSPECTION. Always visually inspect

each chain component for severe wear or dam-

age before sharpening or re-installing it on the

chainsaw. If in doubt, do not sharpen or use the

chain until the parts or the chain can be replaced.

PERSONAL PROTECTIVE EQUIPMENT. Always

wear leather gloves when handling the chain.

To protect yourself from flying particles, put on

safety glasses and respirator before beginning the

sharpening operation.

GRINDING WHEEL INSPECTION. To avoid the

grinding wheel breaking apart during operation,

always inspect it and perform the ring test before

using. If in doubt as to the condition of the wheel,

DO NOT use it!

No list of safety guidelines can be com-

plete. Every shop environment is different.

Always consider safety first, as it applies

to your individual working conditions. Use

this and other machinery with caution and

respect. Failure to do so could result in

serious personal injury, damage to equip-

ment, or poor work results.

Like all machinery there is potential danger

when operating this machine. Accidents

are frequently caused by lack of familiarity

or failure to pay attention. Use this machine

with respect and caution to decrease the

risk of operator injury. If normal safety pre-

cautions are overlooked or ignored, seri-

ous personal injury may occur.

Model T28959 (Mfd. Since 2/19)

-11-

SECTION 2: POWER SUPPLY

Availability

Before installing the machine, consider the avail-

ability and proximity of the required power supply

circuit. If an existing circuit does not meet the

requirements for this machine, a new circuit must

be installed. To minimize the risk of electrocution,

fire, or equipment damage, installation work and

electrical wiring must be done by an electrician or

qualified service personnel in accordance with all

applicable codes and standards.

Electrocution, fire, shock,

or equipment damage

may occur if machine is

not properly grounded

and connected to power

supply.

Full-Load Current Rating

The full-load current rating is the amperage a

machine draws at 100% of the rated output power.

On machines with multiple motors, this is the

amperage drawn by the largest motor or sum of all

motors and electrical devices that might operate

at one time during normal operations.

Full-Load Current Rating at 120V .... 0.6 Amps

The full-load current is not the maximum amount

of amps that the machine will draw. If the machine

is overloaded, it will draw additional amps beyond

the full-load rating.

If the machine is overloaded for a sufficient length

of time, damage, overheating, or fire may result—

especially if connected to an undersized circuit.

To reduce the risk of these hazards, avoid over-

loading the machine during operation and make

sure it is connected to a power supply circuit that

meets the specified circuit requirements.

For your own safety and protection of

property, consult an electrician if you are

unsure about wiring practices or electrical

codes in your area.

Note: Circuit requirements in this manual apply to

a dedicated circuit—where only one machine will

be running on the circuit at a time. If machine will

be connected to a shared circuit where multiple

machines may be running at the same time, con-

sult an electrician or qualified service personnel to

ensure circuit is properly sized for safe operation.

A power supply circuit includes all electrical

equipment between the breaker box or fuse panel

in the building and the machine. The power sup-

ply circuit used for this machine must be sized to

safely handle the full-load current drawn from the

machine for an extended period of time. (If this

machine is connected to a circuit protected by

fuses, use a time delay fuse marked D.)

120V Circuit Requirements

This machine is prewired to operate on a power

supply circuit that has a verified ground and meets

the following requirements:

Voltage ........................................................120V

Cycle ..........................................................60 Hz

Phase ........................................... Single-Phase

Power Supply Circuit ......................... 15 Amps

Serious injury could occur if you connect

machine to power before completing setup

process. DO NOT connect to power until

instructed later in this manual.

-12-

Model T28959 (Mfd. Since 2/19)

Extension Cords

This tool is double-insulated and therefore does

not have a grounding wire or plug. The two-

pronged, NEMA 1-15 plug has a polarized end;

this means that one prong (the neutral connec-

tor) is wider than the other (the hot connector).

Polarized plugs must be used only with polarized

receptacles. Do not attempt to plug this machine

into a non-polarized receptacle. If a polarized

receptacle is not available, a qualified electri-

cal technician will have to install one before the

machine can be plugged in.

Polarized Plug

Figure 10. Typical 1-15 plug and receptacle.

5-15 Receptacle

1-15 Plug

Neutral

Hot

When using extension cords, make sure the cords

are rated for outdoor use. Outdoor use cords are

marked with a "W-A" or a "W" to signify their rat-

ing. Always check to make sure that the extension

cords are in good working order and free of any

type of damage, such as exposed wires, cuts,

creased bends, or missing prongs.

Extension cords cause voltage drop, which may

damage electrical components and shorten motor

life. Voltage drop increases as the extension cord

size gets longer and the gauge size gets smaller

(higher gauge numbers indicate smaller sizes.

When using extension cords, always choose the

shortest cord possible, with the greatest-sized

gauge.

Below is a list of minimum gauge sizes needed for

running this tool at different lengths:

25 Feet ....................................................16AWG

50 Feet .................................................... 14AWG

100 Feet ..................................................12AWG

Over 100 Feet .................... Not Recommended

Model T28959 (Mfd. Since 2/19)

-13-

SECTION 3: SETUP

This machine was carefully packaged for safe

transport. When unpacking, separate all enclosed

items from packaging materials and inspect them

for shipping damage.

If items are damaged

please

call us immediately at (570) 546-9663.

IMPORTANT:

Save all packaging materials until

you are completely satisfied with the machine and

have resolved any issues between Grizzly or the

shipping agent. You MUST have the original pack-

aging to file a freight claim. It is also extremely

helpful if you need to return your machine later.

Unpacking Inventory

The following is a list of items shipped with your

machine. Before beginning setup, lay these items

out and inventory them.

If any non-proprietary parts are missing (e.g. a

nut or a washer), we will gladly replace them; or

for the sake of expediency, replacements can be

obtained at your local hardware store.

Box 1 (Figure 11) Qty

A. Sharpener ................................................... 1

B. Swing Arm Handle ..................................... 1

C. Depth Stop Knob ........................................ 1

D. Chain Holder Assembly .............................. 1

NOTICE

If you cannot find an item on this list, care-

fully check around/inside the machine and

packaging materials. Often, these items get

lost in packaging materials while unpack-

ing or they are pre-installed at the factory.

The following items are needed, but not included,

for the setup/assembly of this machine.

Description Qty

• Safety Glasses ........................................... 1

• Mounting Hardware (Page 15) ... As Needed

Needed for Setup

This machine presents

serious injury hazards

to untrained users. Read

through this entire manu-

al to become familiar with

the controls and opera-

tions before starting the

machine!

Figure 11. T28959 Inventory.

-14-

Model T28959 (Mfd. Since 2/19)

Figure 14. "Direct Mount" setup.

Machine Base

Workbench

Lag Screw

Flat Washer

Another option is a "direct mount" (see example

below) where the machine is secured directly to

the workbench with lag screws and washers.

The strongest mounting option is a "Through

Mount" (see example below) where holes are

drilled all the way through the workbench—and

hex bolts, washers, and hex nuts are used to

secure the machine in place.

Machine Base

Workbench

Hex

Bolt

Flat Washer

Lock Washer

Hex Nut

Figure 13. "Through Mount" setup.

Site Considerations

Figure 12. Minimum working clearances.

11"

Approx. 36" Working Clearance

Children and visitors may be

seriously injured if unsuper-

vised around this machine.

Lock entrances to the shop

or disable start switch or

power connection to prevent

unsupervised use.

Workbench Load

Refer to the Machine Data Sheet for the weight

and footprint specifications of your machine.

Some workbenches may require additional rein-

forcement to support the weight of the machine

and workpiece materials.

Consider anticipated workpiece sizes and addi-

tional space needed for auxiliary stands, work

tables, or other machinery when establishing a

location for this machine in the shop. Below is

the minimum amount of space needed for the

machine.

Placement Location

Bench Mounting

The base of this machine has two holes for

mounting it to a workbench. Because of the

forces applied to the machine during operation,

you MUST securely mount it to a workbench to

prevent it from tipping or shifting during operation.

Any unexpected movement could result in injury

or property damage.

Model T28959 (Mfd. Since 2/19)

-15-

2. Remove angle knob from chain holder

assembly (see Figure 17).

3. Attach chain holder assembly to base (see

Figure 17).

4. Secure chain holder assembly to base with

angle knob (see Figure 17).

Figure 16. Depth stop knob assembly.

Depth Stop Knob Assembly

Swing Arm

Assembly

The Model T28959 is shipped partially assem-

bled. Perform the following procedure to complete

the assembly.

To assemble the sharpener:

1. Thread depth stop knob assembly into hole

on swing arm (see Figure 16).

Figure 17. Attaching chain holder assembly to

base.

Chain

Holder

Assembly

Angle

Knob

Base

Number of Mounting Holes ............................ 2

Diameter of Mounting Hardware Needed ..

⁄8"

Stop

Flange

Figure 15. Stop flange against the workbench.

Base

To mount the sharpener:

1. Place base flat on workbench, slide it back

until stop flanges (see Figure 15) hit front of

the workbench.

2. Mark mounting hole locations and move base

to side.

3. Drill holes in workbench surface.

4. Re-position base over holes and use appro-

priate hardware to securely mount base to

workbench using Through Mount or Direct

Mount techniques (see Figures 13 and 14 on

Page 14).

Angle

Knob

-16-

Model T28959 (Mfd. Since 2/19)

Figure 18. Swing arm handle attached.

Swing

Arm

Handle

5. Thread swing arm handle onto bolt on swing

arm (see Figure 18).

Test Run

Once assembly is complete, test run the machine

to ensure it is properly connected to power and

safety components are functioning correctly.

If you find an unusual problem during the test run,

immediately stop the machine, disconnect it from

power, and fix the problem BEFORE operating the

machine again. The

Troubleshooting

table in the

SERVICE section of this manual can help.

DO NOT start machine until all preceding

setup instructions have been performed.

Operating an improperly set up machine

may result in malfunction or unexpect-

ed results that can lead to serious injury,

death, or machine/property damage.

Serious injury or death can result from

using this machine BEFORE understanding

its controls and related safety information.

DO NOT operate, or allow others to operate,

machine until the information is understood.

To test run machine:

1. Clear all setup tools away from machine.

2. Connect machine to power supply.

3. Turn machine ON, verify motor operation,

and then turn machine OFF.

The motor should run smoothly and without

unusual problems or noises.

The Test Run consists of verifying the following: 1)

The motor powers up and runs correctly.

Model T28959 (Mfd. Since 2/19)

-17-

SECTION 4: OPERATIONS

Operation Overview

The purpose of this overview is to provide the nov-

ice machine operator with a basic understanding

of how the machine is used during operation, so

the

machine controls/components

discussed later

in this manual

are easier to understand.

Due to the generic nature of this overview, it is

not intended to be an instructional guide. To learn

more about specific operations, read this entire

manual,

seek additional

training from experienced

machine operators

, and do additional research

outside of this manual by reading "how-to" books,

trade magazines, or websites.

To complete a typical operation, the operator

does the following:

1. Removes chain from chainsaw.

2. Cleans chain with a non-flammable cleaner

to remove any oil, dirt, and grime, then uses

compressed air to thoroughly dry chain.

3. Examines chain to make sure it is suitable for

sharpening. Checks for damaged broken, or

excessively worn cutter links.

4. Positions chain in chain holder assembly.

5. Secures chain in chain holder assembly by

tightening chain clamp lever.

6. Adjusts chain holder assembly, if necessary,

to desired angle.

7. Secures chain holder assembly angle by

tightening chain holder knob.

8. Adjusts depth stop bolt as needed.

9. Checks infeed and outfeed sides of machine

to make sure workpiece can safely pass all

the way through grinding wheel without inter-

ference.

10. Puts on safety glasses, respirator, and hear-

ing protection.

11. Starts sharpener.

12. Slowly pulls handle down towards chain and

keeps hands and fingers out of the grinding

wheel's path and away from wheel.

13. Stops machine when operation is complete.

To reduce your risk of

serious injury, read this

entire manual BEFORE

using machine.

Eye injuries, respiratory problems, or hear-

ing loss can occur while operating this

tool. Wear personal protective equipment to

reduce your risk from these hazards.

If you are not experienced with this type

of machine, WE STRONGLY RECOMMEND

that you seek additional training outside of

this manual. Read books/magazines or get

formal training before beginning any proj-

ects. Regardless of the content in this sec-

tion, Grizzly Industrial will not be held liable

for accidents caused by lack of training.

-18-

Model T28959 (Mfd. Since 2/19)

How the Chain Cuts

When the rear of the top plate meets the wood

(4), it forces the cutter to continue pivoting forward

and move out of the kerf, producing wood chips

that are carried away by the top plate angle in the

final position (5) to complete the cut.

The goal of this rocking motion is to allow the

chainsaw to self-feed into the wood and do the

work without requiring the operator to force the

chain into the wood. This makes the job easier

and reduces wear on the saw and chain.

Also important is the clearance angle amount.

The downward slope of the top plate enables the

cutter to move into the wood (2) and then forces it

out again (3–4) to complete the cut.

Always use the chain manufacturer's specifica-

tions for the cutter specifications when sharpen-

ing the chain.

Chain Travel

Figure 19. The self-feeding motion of the cutter link during a cutting operation.

Sharp chains cause wood chips to fall away from

the chainsaw. A chip-free chainsaw bar guides

the chain straight through the cut. Dull chains

build up with wood chips, not allowing the chain to

move smoothly around the bar. This causes cuts

that are rough and not true. A dull chain also puts

more strain on the motor.

As illustrated in Figure 19 below, when the cut-

ting point at the top of the cutter moves against

the wood (1), the front of the cutter pivots up until

the depth gauge meets the wood (2), which forces

the cutter to pivot even farther into the wood (3) to

make the cut.

Page is loading ...

Grizzly T28959 Owner's manual

Brand: Grizzly

Model: T28959

Category: Knife sharpeners

Type: Owner's manual

Download PDF

report

Grizzly T28959 Owner's manual

Grizzly T28959 Owner's manual

Related papers

Other documents