DFI EL630-NR User manual

Category
Motherboards
Type
User manual
EL630-NR
System Board
User’s Manual
935-EL6302-000G
A10630048
Copyright
This publication contains information that is protected by copyright. No part of it
may be reproduced in any form or by any means or used to make any transfor-
mation/adaptation without the prior written permission from the copyright hold-
ers.
This publication is provided for informational purposes only. The manufacturer
makes no representations or warranties with respect to the contents or use
of this manual and specifically disclaims any express or implied warranties of
merchantability or fitness for any particular purpose. The user will assume the
entire risk of the use or the results of the use of this document. Further, the
manufacturer reserves the right to revise this publication and make changes to
its contents at any time, without obligation to notify any person or entity of such
revisions or changes.
© 2010. All Rights Reserved.
Trademarks
All trademarks and registered trademarks of products appearing in this manual
are the properties of their respective holders.
FCC and DOC Statement on Class B
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment
is operated in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or televi-
sion reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorientorrelocatethereceivingantenna.
• Increasetheseparationbetweentheequipmentandthereceiver.
• Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhich
the receiver is connected.
• ConsultthedealeroranexperiencedradioTVtechnicianforhelp.
Notice:
1. The changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
2. Shielded interface cables must be used in order to comply with the emission
limits.
1
4
Introduction
Table of Contents
Copyright ...........................................................................................2
Trademarks ........................................................................................2
FCC and DOC Statement on Class B ..............................................3
About this Manual .............................................................................7
Warranty ..........................................................................................7
Static Electricity Precautions .............................................................8
Safety Measures .................................................................................8
About the Package ............................................................................9
Before Using the System Board ........................................................9
Chapter 1 - Introduction ................................................................10
Specifications ................................................................................ 10
Features ...................................................................................... 12
Chapter 2 - Hardware Installation .................................................. 15
System Board Layout .................................................................... 15
System Memory ...........................................................................16
Installing the DIM Module
......................................................... 18
CPU ............................................................................................ 20
Installing the CPU
.................................................................... 20
Installing the Fan and Heat Sink
................................................ 24
Jumper Settings ............................................................................. 26
Clear CMOS Data
..................................................................... 26
PS/2 Power Select
.................................................................... 27
USB Power Select
..................................................................... 28
Power-on Select
....................................................................... 29
PCIEx16/DVISelect .............................................................. 30
Rear Panel I/O Ports .....................................................................31
PS/2 Mouse and PS/2 Keyboard Ports
......................................... 32
COM (Serial) Ports
................................................................... 33
VGAPort ................................................................................. 35
DVI-IPort ............................................................................... 36
RJ45 LAN Ports
........................................................................ 37
USB Ports................................................................................ 38
Audio ..................................................................................... 40
1
5
Introduction
I/O Connectors ............................................................................ 41
CD-in Internal Audio Connector
................................................. 41
S/PDIF Connector
..................................................................... 42
Digital I/O Connector
................................................................ 43
SATA (Serial ATA) Connectors
.................................................... 44
IDE Connector
......................................................................... 45
FDD (Floppy Disk Drive) Connector
............................................ 47
Cooling Fan Connector
.............................................................. 48
Chassis Instrusion Connector
.................................................... 49
Power Connector
...................................................................... 50
Standby LED
........................................................................... 51
Front Panel Connectors
............................................................. 52
Expansion Slots
....................................................................... 53
Battery
................................................................................... 54
Chapter 3 - BIOS Setup .................................................................. 55
Award BIOS Setup Utility .............................................................. 55
Standard CMOS Features
..........................................................56
Advanced BIOS Features
........................................................... 60
Advanced Chipset Features
........................................................ 66
Integrated Peripherals
.............................................................. 69
Power Management Setup
......................................................... 76
PnP/PCI Configurations
............................................................. 80
PC Health Status
...................................................................... 83
Frequency/VoltageControl ........................................................ 84
Load Fail-Safe Defaults
............................................................. 85
Load Optimized Defaults
........................................................... 86
Set Supervisor Password
........................................................... 87
Set User Password
................................................................... 88
Save & Exit Setup
.................................................................... 89
Exit Without Saving
.................................................................. 90
Updating the BIOS ........................................................................ 91
Chapter 4 - Supported Software ................................................... 93
Intel Chipset Software Installation Utility ........................................ 94
Microsoft DirectX 9.0C Driver ......................................................................96
Intel Graphics Drivers ................................................................... 97
Audio Drivers ............................................................................ 102
LAN Drivers .............................................................................. 103
Hardware Monitor for Windows .................................................. 104
Intel Matrix Storage Manager for RAID/AHCI ............................... 111
F6 Floppy Configuration Utility .....................................................................113
Adobe Acrobat Reader 9.3 .......................................................... 114
1
6
Introduction
Chapter 5 - RAID ������������������������������������������������������������������������� 115
RAID Levels
�������������������������������������������������������������������������������� 115
Settings �������������������������������������������������������������������������������������� 116
Appendix A - NLITE and AHCI Installation Guide ����������������������� 118
Appendix B - Watchdog Timer������������������������������������������������������ 130
Appendix C - System Error Message �������������������������������������������� 132
Appendix D - Troubleshooting ������������������������������������������������������ 134
1
7
Introduction
About this Manual
An electronic file of this manual is included in the CD. To view the user’s manual
in the CD, insert the CD into a CD-ROM drive. The autorun screen (Main Board
Utility CD) will appear. Click “User’s Manual” on the main menu.
Warranty
1. Warranty does not cover damages or failures that arised from misuse of the
product, inability to use the product, unauthorized replacement or alteration
of components and product specifications.
2. The warranty is void if the product has been subjected to physical abuse,
improper installation, modification, accidents or unauthorized repair of the
product.
3. Unless otherwise instructed in this user’s manual, the user may not, under
any circumstances, attempt to perform service, adjustments or repairs on the
product, whether in or out of warranty. It must be returned to the purchase
point, factory or authorized service agency for all such work.
4. We will not be liable for any indirect, special, incidental or consequencial
damages to the product that has been modified or altered.
1
8
Introduction
Static Electricity Precautions
It is quite easy to inadvertently damage your PC, system board, components
or devices even before installing them in your system unit. Static electrical dis-
charge can damage computer components without causing any signs of physical
damage. You must take extra care in handling them to ensure against electro-
static build-up.
1. To prevent electrostatic build-up, leave the system board in its anti-static bag
until you are ready to install it.
2. Wear an antistatic wrist strap.
3. Do all preparation work on a static-free surface.
4. Hold the device only by its edges. Be careful not to touch any of the compo-
nents, contacts or connections.
5. Avoid touching the pins or contacts on all modules and connectors. Hold
modules or connectors by their ends.
Important:
Electrostatic discharge (ESD) can damage your processor, disk drive and
other components. Perform the upgrade instruction procedures described
at an ESD workstation only. If such a station is not available, you can
provide some ESD protection by wearing an antistatic wrist strap and
attaching it to a metal part of the system chassis. If a wrist strap is
unavailable, establish and maintain contact with the system chassis
throughout any procedures requiring ESD protection.
Safety Measures
To avoid damage to the system:
• UsethecorrectACinputvoltagerange.
To reduce the risk of electric shock:
• Unplug the power cord before removing the system chassis cover for instal-
lation or servicing. After installation or servicing, cover the system chassis
before plugging the power cord.
Battery:
• Dangerofexplosionifbatteryincorrectlyreplaced.
• Replace only with the same or equivalent type recommend by the manufac-
turer.
• Disposeofusedbatteriesaccordingtolocalordinance.
1
9
Introduction
About the Package
The system board package contains the following items. If any of these items are
missing or damaged, please contact your dealer or sales representative for as-
sistance.
One system board
One IDE cable
Two USB cables
Two Serial ATA data cables
One Serial ATA power cable
One COM port mounted on a bracket (2 pcs)
One I/O shield
One user’s manual
One CD
One QR (Quick Reference)
The system board and accessories in the package may not come similar to the
information listed above. This may differ in accordance to the sales region or
models in which it was sold. For more information about the standard package in
your region, please contact your dealer or sales representative.
Before Using the System Board
Before using the system board, prepare basic system components.
If you are installing the system board in a new system, you will need at least the
following internal components.
• ACPU
• Memorymodule
• Storagedevicessuchasharddiskdrive,CD-ROM,etc.
You will also need external system peripherals you intend to use which will nor-
mally include at least a keyboard, a mouse and a video display monitor.
1
10
Introduction
Processor
Chipset
System Memory
Expansion Slots
Graphics
Audio
LAN
Serial ATA
IDE
Rear Panel I/O
Ports
Chapter 1 - Introduction
•LGA775socketfor:
- Intel
®
Core
TM
2 Quad Q9400
- Intel
®
Core
TM
2DuoE8400/E7400/E6400/E4300
- Intel
®
Pentium
®
E6500/E5300/E2160
- Intel
®
Celeron
®
E3400/E1500/440
•SupportsIntelEnhancedMemory64Technology(EMT64T)
•SupportsEnhancedIntelSpeedStepTechnology(EIST)
•1333/1066/800MHzFSB
•Intel
®
chipset
- Intel
®
Q45Expresschipset
- Intel
®
ICH10DOI/OControllerHub
•Four240-pinDDR3DIMMsockets
•SupportsDDR3800/1066MHz
•Maximum memory bandwidth of 17GB/s in dual-channel
modewhenusingDDR31066MHz
•Dualchannel(128-bitwide)memoryinterface
•Upto8GBsystemmemory
•Supportsunbufferedx8andx16DIMMs
•1PCIExpressx16slot(PCIE2.0)
•1PCIExpressx4slot(PCIEX41.1)
•5PCIslots(PCI2.3)
•IntelGMA4500
- Supports 3D, 2D and video capabilities, DX10 and
OpenGL2.1
•RealtekALC2622-channelHighDefinitionAudio
•Two24-bitstereoDACsandthree20-bitstereoADCs
•S/PDIFinput/outputinterface
•TwoRealtekRTL8111CPCIExpressGigabitcontrollers
•Supports10Mbps,100Mbpsand1Gbpsdatatransmission
•IEEE 802.3 (10/100Mbps) and IEEE 802.3ab (1Gbps) com-
pliant
•Supports6SATA(SerialATA)interfaceswhicharecompliant
withSATA1.0specification
•SATAspeedupto3Gb/s(SATA2.0)
•SupportsRAID0,1,5and10
•SupportsuptotwoIDEdevices
•SupportsUltraATA133/100/66/33
•1mini-DIN-6PS/2mouseport
•1mini-DIN-6PS/2keyboardport
•2DB-9RS232serialports
•1DVI-Iport(DVI-Dsignalonly)
•1DB-15VGAport
•2RJ45LANports
•4USB2.0/1.1ports
•Mic-in,line-inandline-out
Specifications
1
11
Introduction
I/O Connectors
BIOS
Energy Efficient
Design
Da m ag e Fr e e
Intelligence
Temperature
Humidity
PCB
•4connectorsfor8additionalexternalUSB2.0/1.1ports
•2connectorsfor2externalRS232serialports
•1DIOconnector
•1frontaudioconnector
•1CD-ininternalaudioconnector
•1S/PDIFconnector
•6SerialATAconnectors
•140-pinIDEconnector
•1FDDconnector
•124-pinATXpowerconnector
•14-pin12Vpowerconnector
•1chassisopenconnector
•1frontpanelconnector
•3fanconnectors
•AwardBIOS
•8MbitSPIflashmemory
•ACPIspecificationandOSDirectedPowerManagement
•SupportsACPISTR(SuspendtoRAM)function
•Wake-On-Eventsinclude:
- Wake-On-PS/2Keyboard/Mouse
- Wake-On-USBKeyboard/Mouse
- Wake-On-LAN
- Wake-On-Ring
- RTCtimertopower-onthesystem
•Systempowermanagementsupported
•SoftPowersupported-ACPIspecification
•ACpowerfailurerecovery
•MonitorsCPU/systemtemperatureandoverheatalarm
•Monitors CPU/DIMM/3.3V/5V/12V/Chipset Vcore/VBAT
voltagesandfailurealarm
•MonitorsCPU/system/2ndfanspeedandfailurealarm
•Readbackcapabilitythatdisplays temperature,voltageand
fanspeed
•Watchdogtimerfunction
•0
o
Cto60
o
C
•10%to90%
•4-layers,ATXformfactor
•305mm(12”)x244mm(9.6”)
1
12
Introduction
Features
Watchdog Timer
The Watchdog Timer function allows your application to regularly “clear” the sys-
tem at the set time interval. If the system hangs or fails to function, it will reset
at the set time interval so that your system will continue to operate.
DDR3
DDR3 delivers increased system bandwidth and improved performance. It offers
peak data transfer rate of up to 21 Gb/s bandwidth. The advantages of DDR3
are its higher bandwidth and its increase in performance at a lower power than
DDR2.
Graphics
The Intel northbridge chip comes integrated with the Intel Graphics Media Ac-
celerator 4500 delivering an excellent blend of graphics performance and features
to meet business needs. With support for Microsoft DirectX 10, Shader Model 4.0
and OpenGL* 2.0, Intel GMA 4500 delivers excellent video and 3D graphics with
outstanding graphics responsiveness. These enhancements deliver the perfor-
mance and compatibility needed for today’s and tomorrow’s business applications.
DVI
DVI (Digital Visual Interface) is a form of video interface technology made to
maximize the quality of flat panel LCD monitors and modern video graphics
cards. Data is transmitted using the TMDS (Transition Minimized Differential Sig-
naling) protocol, providing a digital signal from the PC’s graphics subsystem to
the display.
PCI Express
PCI Express is a high bandwidth I/O infrastructure that possesses the ability to
scale speeds by forming multiple lanes. The x4 PCI Express lane supports trans-
fer rate of 1 Gigabyte per second. The PCI Express architecture also provides a
high performance graphics infrastructure by enhancing the capability of a x16 PCI
Express lane to provide 4 Gigabytes per second transfer rate.
S/PDIF
S/PDIF is a standard audio file transfer format that transfers digital audio sig-
nals to a device without having to be converted first to an analog format. This
prevents the quality of the audio signal from degrading whenever it is converted
to analog. S/PDIF is usually found on digital audio equipment such as a DAT
machine or audio processing device. The S/PDIF connector on the system board
sends surround sound and 3D audio signal outputs to amplifiers and speakers
and to digital recording devices like CD recorders.
1
13
Introduction
Serial ATA
Serial ATA is a storage interface that is compliant with SATA 1.0a specification.
With speed of up to 3Gbps, it improves hard drive performance faster than the
standard parallel ATA whose data transfer rate is 100MB/s. The system board al-
lows configuring RAID on Serial ATA devices. It supports RAID 0, RAID 1, RAID
0+1andRAID5.
Gigabit LAN
The two Realtek RTL8111C PCI Express Gigabit controllers support up to 1Gbps
data transmission.
USB
The system board supports USB 2.0 and USB 1.1 ports. USB 1.1 supports 12Mb/
second bandwidth while USB 2.0 supports 480Mb/second bandwidth providing a
marked improvement in device transfer speeds between your computer and a
wide range of simultaneously accessible external Plug and Play peripherals.
Wake-On-Ring
This feature allows the system that is in the Suspend mode or Soft Power Off
mode to wake-up/power-on to respond to calls coming from an external modem
or respond to calls from a modem PCI card that uses the PCI PME (Power Man-
agement Event) signal to remotely wake up the PC.
Important:
The 5V_standby power source of your power supply must support
≥720mA.
Wake-On-LAN
This feature allows the network to remotely wake up a Soft Power Down (Soft-
Off) PC. It is supported via the onboard LAN port or via a PCI LAN card that uses
the PCI PME (Power Management Event) signal. However, if your system is in the
Suspend mode, you can power-on the system only through an IRQ or DMA inter-
rupt.
Important:
The 5V_standby power source of your power supply must support
≥720mA.
Wake-On-PS/2
This function allows you to use the PS/2 keyboard or PS/2 mouse to power-on
the system.
Important:
The 5V_standby power source of your power supply must support
≥720mA.
1
14
Introduction
Wake-On-USB
This function allows you to use a USB keyboard or USB mouse to wake up a sys-
tem from the S3 (STR - Suspend To RAM) state.
Important:
If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB
ports, the 5V_standby power source of your power supply must support
≥1.5A. For 3 or more USB ports, the 5V_standby power source of your
powersupplymustsupport≥2A.
RTC Timer
The RTC installed on the system board allows your system to automatically pow-
er-on on the set date and time.
ACPI STR
The system board is designed to meet the ACPI (Advanced Configuration and
Power Interface) specification. ACPI has energy saving features that enables PCs
to implement Power Management and Plug-and-Play with operating systems that
support OS Direct Power Management. ACPI when enabled in the Power Manage-
ment Setup will allow you to use the Suspend to RAM function.
With the Suspend to RAM function enabled, you can power-off the system at
once by pressing the power button or selecting “Standby” when you shut down
Windows
®
without having to go through the sometimes tiresome process of
closing files, applications and operating system. This is because the system is
capable of storing all programs and data files during the entire operating session
into RAM (Random Access Memory) when it powers-off. The operating session will
resume exactly where you left off the next time you power-on the system.
Important:
The 5V_standby power source of your power supply must support
720mA.
Power Failure Recovery
When power returns after an AC power failure, you may choose to either power-
on the system manually or let the system power-on automatically.
15
2
Hardware Installation
System Board Layout
Chapter 2 - Hardware Installation
Mouse
KB
COM 2
COM 1
Top:VGA
Bottom: DV -I I
LAN 1
USB 0-1
LAN 2
USB 2-3
Mic-in
Line-in
Line-out
1
PS/2 power
select (JP8)
1
+12V power
Socket 775
Chrontel
CH7307C
USB 0-3 power
select (JP6)
1
Realtek
RTL8111C
Realtek
RTL8111C
A1
A3
F1
F3
A1
A3
F1
F3
J5
J27
PCIE x16/DVI
select (J5 and J27)
Intel
Q45
PCIE x16
PCIE x4
PCI 1
PCI 2
PCI 3
PCI 4
PCI 5
SPI Flash
BIOS
1
CD-in
1
Realtek
ALC262
1
S/PDIF
1
Front audio
2
9
10
COM 4
1
2
9
COM 3
1
2
9
1
System fan
IDE
1
2
39
40
USB 8-11 power
select (JP9)
1
USB 10-11
1
2
9
10
USB 8-9
1
2
9
10
USB 4-7 power
select (JP7)
1
USB 6-7
1
2
9
10
USB 4-5
1
2
9
10
ITE
IT8213F
Battery
1
Clear CMOS
(JP1)
Intel
ICH10DO
SAT A 0
SAT A 1
SAT A 2
SAT A 3
SAT A 4
SAT A 5
1
Front panel
2
11
12
Standby
Power LED
24
12
ATX power
1
13
Power-on
select (JP5)
1
DIO
12
1920
FDD
21
3433
Winbond
W83627DHG
1
Chassis
intrusion
1
CPU fan
DDR3_4
DDR3_3
DDR3_2
DDR3_1
1
2nd fan
16
2
Hardware Installation
Important:
When the Standby Power LED lit red, it indicates that there is power on
the system board. Power-off the PC then unplug the power cord prior to
installing any devices. Failure to do so will cause severe damage to the
motherboard and components.
System Memory
Important:
Electrostatic discharge (ESD) can damage your system board, processor,
disk drives, add-in boards, and other components. Perform the upgrade
instruction procedures described at an ESD workstation only. If such a
station is not available, you can provide some ESD protection by wearing
an antistatic wrist strap and attaching it to a metal part of the system
chassis. If a wrist strap is unavailable, establish and maintain contact
with the system chassis throughout any procedures requiring ESD pro-
tection.
DIMM 1
DIMM 2
DIMM 3
DIMM 4
Channel A
Channel B
The four DIMM sockets are divided into 2 channels:
Channel A - DIMM 1 and DIMM 2
Channel B - DIMM 3 and DIMM 4
Standby
Power LED
17
2
Hardware Installation
DIMMs are on the same channel.
DIMMs in a channel can be identical or com-
pletely different. However, we highly recommend
using identical DIMMs.
Not all slots need to be populated.
DIMMs of the same memory conguration are
on different channels.
Single Channel
Dual Channel
The system board supports the following memory interface.
Single Channel (SC)
Data will be accessed in chunks of 64 bits (8B) from the memory channels.
Dual Channel (DC)
Data will be accessed in chunks of 128 bits from the memory channels. Dual
channel provides better system performance because it doubles the data transfer
rate.
18
2
Hardware Installation
Note:
The system board used in the following illustrations may not resemble
the actual board. These illustrations are for reference only.
Installing the DIM Module
1. Make sure the PC and all other peripheral devices connected to it has been
powered down.
2. Disconnect all power cords and cables.
3. Locate the DIMM socket on the system board.
4. Push the “ejector tabs” which are at the ends of the socket to the side.
Ejector tab
Ejector tab
5. Note how the module is keyed to the socket.
Key
Notch
19
2
Hardware Installation
7. Seat the module vertically, pressing it down rmly until it is completely seat-
ed in the socket.
6. Grasping the module by its edges, position the module above the socket with
the “notch” in the module aligned with the “key” on the socket. The keying
mechanism ensures the module can be plugged into the socket in only one
way.
8. The ejector tabs at the ends of the socket will automatically snap into the
locked position to hold the module in place.
20
2
Hardware Installation
CPU
The system board is equipped with a surface mount LGA 775 socket. This socket
is exclusively designed for installing a LGA 775 packaged Intel CPU.
Important:
1. Before you proceed, make sure (1) the LGA775 socket comes with a
protective cap, (2) the cap is not damaged and (3) the socket’s con-
tact pins are not bent. If the cap is missing or the cap and/or contact
pins are damaged, contact your dealer immediately.
2. Make sure to keep the protective cap. RMA requests will be accepted
and processed only if the LGA775 socket comes with the protective
cap.
Installing the CPU
1. Make sure the PC and all other peripheral devices connected to it has been
powered down.
2. Disconnect all power cords and cables.
3. Locate the LGA 775 CPU
socket on the system
board.
Important:
The CPU socket must not
come in contact with any-
thing other than the CPU.
Avoid unnecessary expo-
sure. Remove the protec-
tive cap only when you are
about to install the CPU.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137

DFI EL630-NR User manual

Category
Motherboards
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI