Platinum 7096653 CM4117T User manual

INSTRUCTION MANUAL

1.5L COFFEE MAKER

MODEL: 7096653 (CM4117T) EAN: 6001001432450

INDOOR HOUSEHOLD USE ONLY

Please save and read this instruction manual carefully before use.

ENGLISH

INTRODUCTION

Thank you for purchasing our “Platinum” Coffee Maker. Each unit has been

manufactured to ensure safety, reliability, and easy of use. Before use, please

read these instructions carefully and save them for future reference.

IMPORTANT SAFEGUARDS

When using your “Platinum” Coffee Maker, basic precautions should always be

followed, including the following:

l This appliance is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities, or lack of experience and

knowledge concerning the use of this product, unless they are supervised or

have been given instruction concerning use of the appliance by a person

responsible for their safety.

l Children should be supervised to ensure that they do not play with the

appliance.

l Always ensure that the voltage on the rating label corresponds to the voltage

in your home.

l Check the power cord and plug regularly for any damage. If the cord or the

plug is damaged, it must be replaced by the manufacturer or a qualified

person in order to avoid an electrical hazard.

l This appliance is intended for household use only. Industrial or commercial

use will void the warranty, and the supplier can not be held responsible for

injury or damage caused when using the appliance for any other purpose

than that intended.

l Incorrect operation and improper use can damage the appliance and cause

injury to the user.

l Do not use the appliance if it has been dropped or damaged in any way. In

case of damage, take the unit in for examination and/or repair by an

authorized service agent.

l To reduce the risk of electric shock, do not immerse or expose the motor

assembly, plug or the power cord to water or any other liquid.

l Never immerse the unit in water or any other liquid for cleaning purposes.

l Remove the plug from the socket by gripping the plug. Do not pull on the

cord to disconnect the appliance. Always unplug the unit when not in use,

before cleaning or when adding or removing parts.

l The use of accessory attachments that are not recommended or supplied by

the manufacturer may result in injuries, fire or electric shock.

l Do not let the cord hang over the edge of a table or counter. Ensure that

the cord is not in a position where it can be pulled on inadvertently.

l Do not allow the cord to touch hot surfaces and do not place on or near a hot

gas or electric burner or in a heated oven.

l Use of an extension cord with this appliance is not recommended.

However, if it is necessary to use an extension lead, ensure that the lead is

suited to the power consumption of the appliance to avoid overheating of the

extension cord, appliance or plug point. Do not place the extension cord in

a position where it can be pulled on by children or animals or tripped over.

ENGLISH

l This appliance is not suitable for outdoor use. Do not use this appliance for

anything other than its intended use.

l Do not carry the appliance by the power cord.

l Do not touch hot surfaces directly. Use handles or knobs.

l Do not leave this appliance unattended during use. Always unplug the unit

when not in use. Allow it to cool before putting on or taking off parts, and

before cleaning the appliance.

l Always operate the appliance on a smooth, even and stable surface. Do

not place the unit on a hot surface.

l The manufacturer does not accept responsibility for any damage or injury

caused by the improper or incorrect use of the appliance, or by repairs

carried out by unauthorized personnel.

l In case of technical problems, switch off the machine and do not attempt to

repair it yourself. Return the appliance to an authorized service facility for

examination, adjustment or repair. Always insist on the use of original

spare parts. Failure to comply with the above mentioned precautions and

instructions, could affect the safe operation of this machine.

l Do not use this Appliance near bathtubs, showers, basins or other vessels

containing water.

l Always attach plug to appliance first, then plug cord into the wall outlet. To

disconnect, turn any control to “Off”, then remove plug from wall outlet.

l Do not set the carafe on a hot or cold surface.

l Do not use the carafe having a loose or weakened handle.

l Never leave the empty carafe on the keeping warm plate otherwise the carafe is

liable to crack.

l Do not clean the carafe with cleaners, steel wool pads, or other abrasive

materials.

l Avoid contacting moving parts.

l Blades are sharp. Handle carefully.

l Check the grinder box for presence of foreign objects before using.

l Never leave the empty carafe on the keeping warm plate otherwise the carafe is

liable to crack.

l Children should be supervised to ensure that they do not play with the

appliance.

l The container is designed for use with this appliance. It must never be used

on a range top.

l This appliance is intended to be used in household and similar applications

such as:

-Staff kitchen areas in shops, offices and other working environments;

-Farm houses;

-By clients in hotels, motels and other residential type environments;

-Bed and breakfast type environments.

ENGLISH

KNOW YOUR COFFEE MAKER

1. View window

2. Grinder box lld

3. Control panel (see

below)

4. Filter cover

5. Filter

6. Filter holder

7. Warming plate

8. Tank cover

9. Water tank

10. Grinder box

11. Inner cover

12. Water gauge

13. Carafe lld

14. Carafe

15. Carafe handle

ENGLISH

SPECIFICATIONS

Capacity :

1.5 Liters / 12 cups (125 ml / cup)

Voltage :

AC 220-240V / 50Hz

Wattage :

1000W

Cord :

3-pin grounded plug. (to reduce risk of electric shock)

USING YOUR COFFEE MAKER

Before first use, please follow these instructions:

1. Remove all packaging and any labels,

2. Fill to the maximum level mark with fresh water, boil and empty the coffee

maker at least 2 times to clear coffee maker of any tiny particles. Do not drink

the water.

3. Cleaning all the detachable parts, such as the grinder box, filter, filter holder

and so on completely.

Set the clock

1. Once the appliance is connected to power supply, 88:88 will display and flash on

the LED display, after 5s, the LED will display 12:00.

Note: If you do not set the clock, you can go directly to other settings.

2. Press the “program” button once (see LED display). You are now in the

“Time Set” mode and can operate either “hr” or “min” button to achieve the

desired setting.

3. Confirm the clock setting by waiting for 15 seconds.

4. The buttons can be held down to scroll through the digits, or pressed and

released lightly to advance one digit at a time.

Note: The time cycle is 24 hours (the details refer to the LED display).

To set the program time

If you do not want the coffee maker start operation immediately, you may set the

automatic start function as follows:

1. After set the clock (suppose the current time is 13:30). Press the “program”

button twice. You will enter the state of “preset the automatic start time”(see

LED display). The desired time can be set by pressing the” hr” and “min”

buttons to scroll forward through the digits.

2. When the desired time setting approaches, press the on/off button twice.

The indicator of program will be illuminated. When the preset time achieves

and the indicator of program will be extinguished. The indicator of on/off will

be illuminated and the coffee maker will start to brew.

Note: you can see the automatic start time by pressing the “program”. You

can determine the display time is programmed time or current time by

seeing the lower indicator on the LED (the details refer to the LED display)

3. If you want to cancel the preset program, press the on/off button twice. The

appliance will start to brew immediately.

4. Reset the “automatic start” mode, only following the steps 1-2 again.

ENGLISH

TO USE YOUR COFFEE MAKER

Before you make the first pot of coffee in your new appliance, we recommend

operating the coffee maker once, using only water and paper filter. This will

remove any dust or residues which remain in the system from the

manufacturing process.

1. Add beans: Open the tank cover by pushing the release button and lifting

up, and remove the grinder box , then open the grinder box lid by screwing it, fill

the grinder box with the desired quantity of beans according to the marks on

the grinder box. The marks indicate the coffee bean which making

corresponding coffee (see fig.1). Generally load the grind box 2OZ beans most.

Do not overfill or the Grinder box may be blocked and/or the coffee maker may

overflow. And assemble the grinder box into the coffee maker, it must be noted

the connector groove must be locked into the motor shaft (see fig.2), otherwise

the grinder box will not be assembled in place properly, and it may damage the

grinder box.

Note: the grinder box must be removed for adding beans.

2. And replace the grinder box cover (see fig.3), first place into position from

the “ ” position, then turn the grinder box lid in clockwise until it lock into the

“ ”position), otherwise the appliance will not operate.

Proportions

exaggerated

for clarity

Fig.3

ENGLISH

3. Fill the tank: after add beans, then pouring the desired amount of water in the

tank from the indication on the inner cover (see fig.4), and the water level

shall according to the gauge located at the right of the tank.

Note: before filling water, the inner cover must be assembled in place.

4. Pull out the filter holder: Place itself permanent filter in the filter holder and

replace the filter cover. Then push the filter holder in place.

Note: a permanent filter may allow some ground coffee to flow into carafe.

5. Close the tank cover: Press down to lock. The appliance is equipped with a

safety interlock system. The details refer to the section of “PROBLEM

SOLVING”.

6. Before brewing coffee: Make sure you have replaced the carafe in its

position on the keeping warm plate.

7. Plug the cord into an electrical outlet. “88：88” will display and flash on the

LED, after 5s, “12:00” will appear until you set the time. Set the current clock

according to the “Set the clock” section on the above.

8. Make sure the indicator of grind off must be extinguished.

Note: If the indicator of grind off is illuminated, it means that the appliance is on

the “make coffee with pre-ground bean” mode. The appliance will omit the step

of grinding bean.

9.Select Cups Setting: The 1-4cup setting button is used to control the time of

grinding bean, if you want make 1-4 cup coffee, press the button and the

indicator of 1-4 cup will be illuminated. The time of grinding bean is about 30s.

If you do not press the button, the default set is 5-12 cups. The time of

grinding bean is about 40s.

Note: the 1-4 cup button only use in the “make coffee with bean” mode. In other

words, the indicator above of the button of grind off must be extinguished. In

the “make coffee with pre-ground bean” mode, it is unused. And during

operation, the button is not activated.

Proportions

exaggerated

for clarity

Fig.4

ENGLISH

10. Start to operate:

① Immediate grinding and brewing: Press the on/off button, the indicator of run

will light and the process will begin.

② Programmed brewing: If you do not want the coffee maker start operation

immediately, you may set the automatic start function according to the “Set the

program time” on the above.

11. When finish grinding bean, the brewing process begins.

Note: During operation, you can take out carafe, pour and serve at any time.

The appliance will stop dripping automatically. But the time cannot exceed 30

seconds.

Caution: when the brewing has almost finished, the quantity of steam will be

much more, and the steam may run out from control panel, filter holder and

other gap. It is normal, you only need to care of not be burned by steam, it will

not affect the normal operation.

12. Once the coffee has been finished brewing, stir it before serving to blend

the flavors. The coffee at the bottom of the carafe will be somewhat

stronger than the coffee at the top. After brewing, the unit will keep warm

for 2 Hours and then automatically shut power off.

Or press the on/off button twice to shut power off and unplug the power outlet.

Make Coffee with Pre-ground Beans

1. Fill the tank: Open the tank cover by pushing the release button and lifting up.

Make sure the inner cover is in place, then pouring the desired amount of

water in the tank according to the gauge located at the right of the reservoir.

2. Pulling out the filter holder. Add ground coffee to our permanent filter. Our

recipe suggestion: Use 1 level scoop of ground coffee per cup. Adjust the

recipe according to your individual.

Note: The maximum capacity for ground coffee is 10 level scoops, using a

permanent filter. Exceeding that amount may cause overflow if the coffee is too

finely ground.

3. Replace the filter cover and push the filter holder in place.

4. Before brewing coffee: Make sure you have replaced the carafe in its

position on the keeping warm plate and have placed a filter in the filter holder,

replace the filter cover.

5. Plug the cord into an electrical outlet. “88：88” will display and flash on the

LED, after 5s, “12:00” will appear until you set the time. Set the current clock

according to the “Set the clock” section on the above.

6. Press the “grind off” button and the indicator of grind off will be illuminated.

The appliance will omit the step of grinding bean and enter the brewing

operation once you press the on/off button or the preset time achieves.

7. Follow instructions 9 through 11 from the Make Coffee with bean section.

ENGLISH

Pause serve

This feature allows you to pour a cup of coffee before the entire brew cycle has

completed. By removing the Carafe, the flow of coffee from the bottom of the

filter will stop.

Caution: Return carafe to warming plate within 30 seconds. Hot water

continues to flow into the filter when this feature is used. Overflowing coffee

and hot water would be a burn hazard.

Automatic shutoff

The Automatic Shutoff feature shuts off the warming plate 2 hours after brew

cycle begins. Always turn coffee maker off and unplug when finished.

CARE AND CLEANING

Completely clean and dry all detachable parts after every use. It must be

maintain for 30 minutes every two cycles. The purpose is let the appliance cool

down completely.

1. Always turn coffee maker off and remove the plug from the electrical outlet

before cleaning.

2. Remove all the detachable parts.

3. After remove the carafe from the warming plate, discard any remaining

coffee. The carafe and lid can be washed in warm soapy water and rinsed

thoroughly, or placed in a dishwasher. The carafe and carafe lid should be

placed on the upper rack only.

4. Pull out the filter holder. Remove filter cover and filter.

5. The grinder box, grinder box lid, filter, filter holder and filter cover can be

washed in warm soapy water and rinsed thoroughly, or cleaned in the upper

rack of the dishwasher. Dry all parts after every use.

6. Do not put any water in the unit once the grinder box has been removed.

Wipe the area under the grinder box with a damp cloth. If water gets into the

grinder motor, the motor may become damaged and may malfunction.

7. Once after cleaning, reverse the above steps.

Note:

a) Do not use scouring agential or harsh cleansers on any part of the coffee

maker.

b) Never immerse base unit in water or other liquid. To clean base, simply

wipe with a clean, damp cloth and dry before storing.

c) Wipe the keeping warm plate with a clean, damp cloth. Never use rough,

abrasive material or cleaners to clean the resting plate.

d) Do not dry the inside of the tank with a cloth, as lint may remain.

ENGLISH

PROBLEM SOLVING

During operation, if the water tank cover/ grinder box/carafe are not in place

separately, the motor will be cut off, the buzzer will alarm, and the LED will

display and flash. The details of display according to the following:

(1) If the tank cover is not in place, the display will show“OPN1”and alarm

sound will be heard.

(2) If the grinder box is not in place, the display will show“OPN2”and alarm

sound will be heard.

a. If on the state of grinding bean, replace the grinder box, and close the water

tank cover within 5s, the appliance will continue to working, If the time

exceed 5s, the appliance will stop.

b. If on the state of heating, replace the grinder box and water tank at any time,

the appliance will continue to working.

DECALCIFICATION

Decalcification refers to removing the calcium deposits which form over time on

the metal parts of the coffee maker.

For best performance from your coffee maker, decalcify the base unit from time

to time. The frequency depends upon the hardness of your tap water and how

often you use the coffee maker.

To clean, fill the water reservoir to capacity with a mixture of 1/3 white vinegar

and 2/3 water. Turn the coffee maker on by pressing the ON button. One cycle

should be sufficient to adequately clean the coffee maker. When the cycle is

completed and the five beeps sound, turn coffee maker off. Repeat operation,

this time using fresh cold water.

ENGLISH

WARRANTY

PLEASE AFFIX YOUR RECEIPT/PROOF OF PURCHASE HERE.

IN THE EVENT OF A CLAIM UNDER THIS WARRANTY THE

AFORESAID RECEIPT/PROOF OF PURCHASE MUST BE

PRODUCED TOGETHER WITH THIS WARRANTY.

Model number (Lot number: )

Product name

Date of purchase

Place of purchase

1. The party selling the product (“the seller”) to the original purchaser of

this product (“the customer”) hereby warrants that this product will be of

good quality and, in good working order and, free of defects and

suitable for its intended purpose under normal household use, for a

period of 1 (one) year from the date of purchase (“warranty period”) of

this product.

2. In the event that the warranty period has not lapsed and the product is

not of a good quality, or in good working order or, is defective or is not

suitable for its intended purpose under normal household use, the

customer may, subject to paragraph 3 below, return the product to the

seller and have the following options available:

2.1 Within the first 6 (six) months of the warranty: to receive a

refund of the actual price paid or to exchange the product for the

same or similar product of the same purchased value;

2.2 Within the second 6 (six) months of the warranty: to have the

product exchanged for the same or similar product of the same

purchased value.

3. The seller will not replace the product or refund the customer in terms of

this warranty if the product:

3.1 has been altered contrary to the instructions provided in the

product manual;

3.2 has been misused, abused or tampered with;

3.3 is defective or not in working order due to ordinary wear and

tear;

3.4 is damaged resulting from the customer’s gross negligence,

recklessness, malicious behavior or criminal conduct;

3.5 has been utilised for commercial use.

4. This warranty applies only to the product that has been purchased from

the seller and not to any expendables attached to or installed on the

product by the customer.

5. Any claim in terms of this warranty must be supported by the original

proof of purchase.

Page is loading ...

Platinum 7096653 CM4117T User manual

This manual is also suitable for

Platinum 7096653 CM4117T User manual

in other languages

Related papers

Other documents