Simplicity 071039 User manual

Brand: Simplicity

Model: 071039

Category: Power generators

Type: User manual

Installation & Operator’s Manual

100 Amp NEMA 3R

Automatic Transfer Switch

with AC Power Control Module

™

NOT

FOR

REPRODUCTION

Thank you for your purchase of this Briggs & Stratton Power Products® Automatic Transfer Switch. This product is intended

for use with Briggs & Stratton Home Standby Generators and therefore may not function with generators produced by other

manufacturers. Seek a qualified electrical professional to determine applicability of this equipment to generators aside from

those manufactured by Briggs & Stratton. This is an optional home standby system which provides an alternate source of

electric power and to serve loads such as a gas furnace, refrigeration and communication systems that, when stopped during

any power outage, could cause discomfort, or the like. This product does not qualify for emergency standby as defined by

NFPA 70 (NEC).

This manual contains safety information to make you aware of the hazards and risks associated with transfer switches and

how to avoid them. Briggs & Stratton has made every effort to provide for a safe, streamlined and cost-effective installation.

Each installation is unique, it is impossible to know of and advise of all conceivable procedures and methods by which

installation might be achieved. We do not know all possible hazards and/or the results of each method or procedure. Save

these instructions for future reference.

This transfer switch requires installation before use. Refer to the Installation section of this manual for instructions on

installation procedures. Only licensed electrical contractors should install transfer switches. Installations must strictly

comply with all applicable federal, state and local codes, standards and regulations.

Where to Find Us

You never have to look far to find Briggs & Stratton support and service for your transfer switch. There are thousands of

Briggs & Stratton authorized service dealers worldwide who provide quality service. You can also find the nearest Authorized

Service Dealer in our dealer locator map on the Internet at BRIGGSandSTRATTON.COM.

Date of Purchase

Transfer Switch

Model Number

Model Revision

Serial Number

Briggs & Stratton Power Products is a registered

trademark of Briggs & Stratton Corporation

Milwaukee, WI, USA

2 BRIGGSandSTRATTON.COM

NOT

FOR

REPRODUCTION

Table of Contents

Important Safety Instructions........................4

Introduction....................................5

For the Home Owner ..........................................5

Owner Orientation ............................................5

Installer Responsibilities .......................................5

Equipment Description.........................................5

Installation ....................................6

Unpacking ..................................................6

Mounting Guidelines ..........................................6

System Setup................................................7

Supervisory Control Wiring .....................................7

Wiring Interconnections........................................8

Controls ..................................... 10

Operation .................................... 10

Testing the Automatic Transfer Switch ...........................10

Maintenance .................................. 10

Troubleshooting................................ 11

Transfer Switch Installation Schematic ...........................12

Transfer Switch Installation Diagram.............................13

Warranty..................................... 14

Specifications ................................. 16

NOT

FOR

REPRODUCTION

4 BRIGGSandSTRATTON.COM

Important Safety Instructions

This is the safety alert symbol. It is used to alert

you to potential personal injury hazards. Obey all

safety messages that follow this symbol to avoid

possible injury or death.

The safety alert symbol ( ) is used with a signal word

(DANGER, CAUTION, WARNING), a pictorial and/or a safety

message to alert you to hazards. DANGER indicates a hazard

which, if not avoided, will result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could

result in death or serious injury. CAUTION indicates a hazard

which, if not avoided, might result in minor or moderate

injury. NOTICE indicates a situation that could result in

equipment damage. Follow safety messages to avoid or

reduce the risk of injury or death.

The manufacturer cannot possibly anticipate every possible

circumstance that might involve a hazard. The warnings in

this manual, and the tags and decals affixed to the unit are,

therefore, not all-inclusive. If you use a procedure, work

method or operating technique that the manufacturer does

not specifically recommend, you must satisfy yourself that

it is safe for you and others. You must also make sure that

the procedure, work method or operating technique that you

choose does not render the transfer switch unsafe.

WARNING

Only qualified electricians should attempt installation of

this system, which must strictly comply with applicable

codes, standards and regulations.

WARNING

Low voltage wire cannot be installed in same

conduit as power voltage wiring.

• Failure to follow above warning could cause personal

injury, damage and/or malfunction of equipment.

WARNING

Failure to properly ground transfer switch can

result in electrocution.

• DO NOT touch bare wires or receptacles.

• DO NOT use transfer switch with worn, frayed, bare or

otherwise damaged wiring.

• DO NOT handle electrical cords while standing in water,

while barefoot, or while hands or feet are wet.

• If you must work around a unit while it is operating,

stand on an insulated dry surface to reduce shock

hazard.

• DO NOT allow unqualified persons or children to operate

or service transfer switch.

• In case of an accident caused by electrical shock,

immediately shut down the source of electrical power

and contact local authorities. Avoid direct contact with

the victim..

WARNING

Transfer Switch contains hazardous voltage

that can cause personal injury or death.

Installing or removing current transformer

when generator is operating will produce

hazardous voltage that can cause personal

injury or death.

• Despite the safe design of the transfer switch, operating

this equipment imprudently, neglecting its maintenance

or being careless can cause possible injury or death.

• DO NOT install, remove or open current transformer

circuit without removing 15 amp fuse in generator and

placing generator switch in OFF position.

• To reduce risk of electrical shock or personal injury,

disconnect all sources of supply voltage before servicing.

NOTICE

Improper treatment of transfer switch can damage it and

shorten its life.

• Use transfer switch only for intended uses.

• If you have questions about intended use, ask dealer or

contact Briggs and Stratton Power Products.

• DO NOT expose transfer switch to excessive moisture,

dust, dirt, or corrosive vapors.

• Remain alert at all times while working on this

equipment. NEVER work on the equipment when you are

physically or mentally fatigued.

• If connected devices overheat, turn them off and turn off

their circuit breaker/fuse.

Save These Instructions

NOT

FOR

REPRODUCTION

Introduction

Your Briggs & Stratton Transfer Switch is supplied with this

combined “Installation and Operator’s Manual”. This is an

important document and should be retained by the owner

after the installation has been completed.

Every effort has been expended to make sure that the

information in this manual is both accurate and current.

However, the manufacturer reserves the right to change,

alter or otherwise improve the system at any time without

prior notice.

For the Home Owner

To help you make informed choices and communicate

effectively with your installation contractor(s),

Read and understand the Owner Orientation Section

of this manual BEFORE contracting or starting your

transfer switch installation.

To arrange for proper installation, contact the store at which

you purchased your Briggs & Stratton Transfer Switch, your

dealer, or your utility power provider.

The Transfer Switch Warranty is VOID

unless the system is installed by a

licensed electrical professional.

Owner Orientation

The illustrations are for typical circumstances and are meant

to familiarize you with the installation options available with

your transfer switch.

Local codes, appearance, and distances are the factors that

must be considered when negotiating with an installation

professional. As the distance from the existing electrical

service increases, compensation in wiring materials must

be allowed for. This is necessary to comply with local codes

and overcome electrical voltage drops.

The factors mentioned above will have a direct effect on the

overall price of your transfer switch installation.

NOTE: Your installer must check local codes AND obtain

permits before installing the system.

 • Readandfollowtheinstructionsgiveninthismanual.

 • Followaregularscheduleincaringforandusingyour

transfer switch, as specified in the manual.

Installer Responsibilities

 • Readandobservethesafetyrules.

 • Readandfollowtheinstructionsgiveninthismanual.

 • Checkfederal,stateandlocalcodesandauthority

having jurisdiction, for questions on installation.

 • Ensuregeneratorisnotoverloadedwithselectedloads.

If you need more information about the transfer switch,

contact your local Authorized Service Center.

Equipment Description

The transfer switch is intended to transfer the entire load

of normal residential installations when used with the

supervisory contacts provided. The load is connected either

to utility power (normal) or home standby power (generator).

The transfer switch monitors utility and generator voltages

and will automatically connect to the appropriate source of

power.

Major components of the transfer switch are a 2 pole double

throw transfer switch, control circuit board, fused utility

terminals and interconnecting wiring. The control board also

has two inputs for current transformers that sense generator

current.

The transfer switch is solenoid-operated from utility or

generator inputs and contains suitable mechanical and

electrical interlock switches to eliminate the possibility of

connecting the utility service to the generator output. It

has ratings capable of switching full utility power into the

residence. In addition, a manual override lever is provided

for the transfer function.

The control circuit board has active circuits sensing utility

and generator voltages. It creates a signal for the generator

start-up, switch transfer, and retransfer when utility is

restored. The control board also contains red and green

LED’s indicating the power sources available and two

relay operated contacts that provide supervisory control of

external loads.

When protected by one of the type circuit breakers described

below, this transfer switch is rated for use on a circuit

capable of delivering not more than 22,000 rms symmetrical,

240 volts max.

 • Cutler-HammerTypeQCHW

 • Cutler-HammerTypeGB,GHB,GC,GHC

 • Cutler-HammerTypeFD,GD,HFD

 • SquareDTypeQOM1,QOM2,QOM1-VH,QOM2-VH

 • SquareDTypeQ2-H,Q2H,QDL

 • GETypeTHHQB,THHQC,THHQL,THQD,TQDL,THQDL

 • SiemensTypeHED4

NOT

FOR

REPRODUCTION

6 BRIGGSandSTRATTON.COM

Installation

Unpacking

Delivery Inspection

After removing the carton, carefully inspect the transfer

switch components for any damage that may have occurred

during shipment.

IMPORTANT: If loss or damage is noted at time of delivery,

have the person(s) making delivery note all damage on the

freight bill and affix his signature under the consignor’s

memo of loss or damage. If loss or damage is noted after

delivery, contact the carrier for claim procedures. Missing or

damaged parts are not warranted.

Shipment Contents

 • AutomaticPowerTransferSwitch

 • CurrentTransformerKit

 • InstallationandOperator’sManual

Mounting Guidelines

The Automatic Transfer Switch is enclosed in a NEMA Type 3R

enclosure suitable for indoor/outdoor use. Guidelines for

mounting the Automatic Transfer Switch include:

 • Installtheswitchonafirm,sturdysupportingstructure.

 • TheswitchmustbeinstalledwithminimumNEMA3R

hardware for conduit connections.

 • Topreventswitchcontactdistortion,levelandplumbthe

enclosure. This can be done by placing washers between

the switch enclosure and the mounting surface.

 • NEVERinstalltheswitchwhereanycorrosive

substance might drip onto the enclosure.

 • Protecttheswitchatalltimesagainstexcessivemoisture,

dust, dirt, lint, construction grit and corrosive vapors.

A typical installation of the Automatic Power Transfer Switch

is depicted below. An alternative installation of the Automatic

Power Transfer Switch is also depicted below. It is best if

the transfer switch is mounted near the utility meter, either

inside or outside. Discuss layout suggestions/ changes with

the owner before beginning the system installation process.

Typical

Main

Distribution

Panel

Transfer

Switch

Hot

Water

Heater

Air

Conditioner

Contactor

Generator

Watt -

Hourmeter

— — — — — — Control Wiring

Disconnect Switch

Branch Circuits

Alternate

Main

Distribution

Panel

Transfer

Switch

Hot

Water

Heater

Air

Conditioner

Contactor

Generator

Watt -

Hourmeter

— — — — — — Control Wiring

Disconnect Switch

Branch Circuits

Emergency

Load

Center

Service Disconnect

NOT

FOR

REPRODUCTION

System Setup

You must perform the following before operating the system:

 • Ifgeneratorisinstalledinanarearegularlysubjectedto

temperatures below 40°F (4°C), select a 50 second warm up

time by moving jumper JP2 (C) installed on transfer switch

control board from ‘20’ position to ‘50’position.

 • SettheDPSW1(A) and DPSW2 (B) dipswitches on the

transfer switch control board to match the kW rating of the

standby generator, as described in SettingDipswitches.

Setting Dipswitches

Dipswitches are used to adjust control board operation based

on generator capacity. DPSW1 and DPSW2 switches are set to

correspond to total system kW rating. Dipswitch DPSW1 (A) has

units of 1,000 watts; Dipswitch DPSW2 (B) has units of

10,000 watts.

Set dipswitches with utility and generator power removed from

the transfer switch to ensure proper control system operation.

If dipswitches are set when power is present at transfer switch,

a power reset needs to be performed before the new dipswitch

settings will take effect. Power reset is when all power is removed

from the transfer switch and then reintroduced after 30 seconds.

NOTICE An FC_8 will occur on standby generator control board if

dipswitches are not properly established as noted above.

The “On” position for the dipswitches is the switch number ON

THE TRANSFER SWITCH CONTROL BOARD, not on the switch. For

example, for an 18,000 watt generator, set DPSW2 dipswitch 10 to

“On” position. Set DPSW1 dipswitch 8 to “On” position. 10,000 plus

8000 equals 18,000 watts.

Set only one switch to “On” position

on DPSW1 andDPSW2.

Refer to following chart for proper switch selection(s).

NOTICE

Air density is less at high altitudes, resulting in less

available engine power. Specifically, engine power will decrease 3.5%

for each 1,000 feet (300 meters) above sea level and 1% for each 10°

F (5.6°C) above 77°F (25°C). Generators located in these conditions

must have the transfer switch programmed appropriately for this

power decrease.

DPSW

DPSW2

JP2

kW Rating

Generator

DPSW

#1 “ON”

Position

DPSW

#2 “ON”

Position

7kW 7 0

8kW 8 0

9kW 9 0

10kW* 0 10

11kW* 1 10

12kW 2 10

13kW* 3 10

14kW 4 10

15kW 5 10

16kW 6 10

17kW 7 10

18kW 8 10

19kW 9 10

20kW 0 20

30kW 0 30

45kW 5 40

48kW 8 40

50kW 0 50

60kW 0 60

* For generators with a rating that includes 500 Watts, round

down to next lowest rating

(example: 13.5 kW set to 13kW)

NOT

FOR

REPRODUCTION

8 BRIGGSandSTRATTON.COM

Supervisory Control Wiring

1. Terminal strip on control module in transfer switch

has four connections for customer use. There are two

sets of “Normally Closed” contacts available. They will

be activated when generator power is required. These

can be used for supervisory control of large connected

loads on generator. Loads will be allowed to operate if

there is enough generator power available.

NOTE: There are two wireways provided to keep the

supervisory loads separated from each other.

2. Terminals “A-A” on control module are rated for

24 VAC and air conditioner contactor control. Contacts

are connected in series with the air conditioner

contactor control circuit.

3. Terminals “B-B” on control module are rated for 5 Amp

250 VAC and installer supplied contactor to control a

large load. Example: electric hot water heater. Contacts

are connected in series with the contactor control circuit.

4. Tighten all wire connections/fasteners to proper torque.

See inside transfer switch enclosure for proper torque

values.

Wiring Interconnections

All wiring must be the proper size, properly supported and

protected by conduit.

Complete the following connections between the transfer

switch, main distribution panel, utility power and generator,

as shown on the next page.

WARNING

Low voltage wire cannot be installed in same

conduit as power voltage wiring.

• Failure to follow above warning could cause personal

injury, damage and/or malfunction of equipment.

High Voltage Wiring

1. Ensure utility power is turned OFF. Connect utility

feeder conductors to transfer switch terminals marked

“UTILITY CONNECTION”. Connect utility live to “N1”

and utility neutral to “N2”.

2. Connect distribution panel feeder conductors to transfer

switch terminals marked “LOAD CONNECTION”.

Connect live to “T1” and neutral to “T2”.

3. Connect distribution panel Ground conductor to the

transfer switch “GND” terminal.

NOTE: Assure grounding electrode conductor is connected

and bonded per applicable federal, state and local codes,

standards and regulations.

Generator feeder conductors are shown below:

4. Connect generator feeder conductor from the generator

circuit breaker terminal “E1” to transfer switch terminal

marked “GENERATOR CONNECTION” terminal “E1”.

This conductor should pass through hole of current

transformer before making the connection.

5. Connect other generator feeder conductor from the

generator circuit breaker terminal “E2” to transfer

switch terminal marked “NEUTRAL”. This conductor

should pass through hole of current transformer before

making the connection.

6. Connect a cable from transfer switch terminal

marked “Neutral” to transfer switch terminal marked

“GENERATOR CONNECTION” terminal “E2”.

7. Connect a cable from transfer switch terminal marked

“Neutral” to transfer switch terminal marked “Ground”.

240V

120V

#22

Air Conditioner Contactor

24 VAC

Contactor

230 VAC

NOT

FOR

REPRODUCTION

Main Distribution Panel

To Generator

Neutral

Terminal

Supervisory

Contacts

To Utility Power

Generator

Connection

Utility

Connection

Ground

Terminal

230V Generator

Connection

Main

Ground Bus

Wireway

Load

Connection

CT 2

CT 1

Generator Tx Rx and

Tx Rx Ground Connection

Ground

GND

Tx Rx

Tx Rx GND

Connector tightening torques shall be as follows:

Utility 5.5 Nm Ground 5.5 Nm

Generator 5.5 Nm Control 1.4 Nm

Neutral 12.5 Nm Fuseblocks 1.4 Nm

Use oxide inhibitor on all aluminum terminations.

All terminal and bus lugs are suitable for copper wire of

60°/75°C rating.

NOT

FOR

REPRODUCTION

NOTE: This connection grounds the neutral side of the

generator output, and is required for correct operation of

protection devices in the installation.

8. Plug in current transformer leads into “CT1” and “CT2”

on control module.

9. Connect generator Ground conductor from the control

panel to the transfer switch “GND” terminal.

NOTE: Assure generator equipment grounding conductor

is connected per applicable federal, state and local codes,

standards and regulations.

10. Connect generator “UTILITY 230 VAC” terminals to

transfer switch “UTILITY 230 VAC” terminals (F1, F2).

Use minimum 2.5mm

conductors.

NOTE: Replace with fuse of same type and rating, 600 volt,

2 amp.

11. Tighten all wire connections/fasteners to proper torque

as shown below.

Low Voltage Wiring

1. Using 1.0mm

twisted pair conductors, no greater than

60 m in length, connect Tx Rx and Tx Rx Ground from

the generator control panel to the GND and T/R on the

transfer switch control board.

2. Tighten all wire connections/fasteners to proper torque.

Controls

Other than a Manual Override lever, there are no operator

controls because this is an automatic transfer switch. The

manual override is to be used only by licensed professionals.

Operation

To select automatic transfer operation, do the following:

1. Set service disconnect switch that sends utility power

to transfer switch contactor to “On” position.

2. Set generator’s main circuit breaker to its “On”

position.

3. Install 15 Amp fuse in control panel on generator.

4. Set generator system AUTO/OFF switch to “AUTO”

position.

The system will now be in automatic operation mode.

When the generator is providing power to the transfer

switch, the controller is constantly monitoring generator

power. If the air conditioner is called to run, and there is

sufficient generator power available, the controller will close

contacts “A-A” to air conditioner contactor. Contacts “B-B”

will open before contacts A-A close. If loads are too great

for generator, contacts A-A and/or B-B will open. When air

conditioning is not needed, A-A will open. If enough power is

available, B-B will close.

Testing the Automatic Transfer Switch

Turn the service disconnect feeding the transfer switch

contactor to the “Off” position. The Automatic Sequence of

the system will follow. To go back to utility power, turn the

service disconnect to the “On” position.

Utility Fail

The Home Standby Generator set senses when utility voltage

is below 70 percent of nominal. Engine start sequence is

initiated after 6 second time delay.

Engine Warm-Up

Time delay to allow for engine warm-up before transfer is

fixed at 20 seconds or 50 seconds (see System Setup).

Transfer

Transfer from utility to generator supply occurs after voltage

is above set levels. Minimum engine run time is 5 minutes

after transfer.

Utility Pickup

Voltage pickup level is 80 percent of nominal voltage.

Retransfer

Retransfer from generator to utility supply is approximately

10 seconds after utility voltage supply is above pickup level

and minimum run time is completed.

Engine Cool Down

Engine will run for 60 seconds after retransfer.

10 BRIGGSandSTRATTON.COM

Generator

Transfer

Switch

NOT

FOR

REPRODUCTION

Maintenance

The transfer switch is designed to be maintenance free under

normal usage. However, inspection and maintenance checks

should be made on a regular basis. Maintenance will consist

mainly of keeping the transfer switch clean.

Visual inspections should be done at least once a month.

Accesstotransferswitchmustnotbeobstructed.Keep

92 cm clearance around transfer switch. Check for an

accumulation of dirt, moisture and/or corrosion on and

around the enclosure, loose parts/hardware, cracks and/

or discoloration to insulation, and damaged or discolored

components.

Exercise the transfer switch at least once every three months

as described in the previous section Testing the Automatic

Transfer Switch unless a power outage occurs and Home

Generator System has gone through automatic sequence.

Allow generator to run for at least 30 minutes.

Contact a licensed electrical professional to inspect and clean

the inside of your transfer switch at least once a year.

Reinstall barrier after service or maintenance.

Problem Cause Correction

Automatic transfer switch does not

transfer to generator

1. Generator breaker open.

2. Generator voltage not acceptable.

1. Reset generator circuit breaker.

2. Refer to generator manual.

Automatic transfer switch does not

transfer to utility

1. Service disconnect breaker open.

2. Utility voltage not acceptable.

1. Reset service disconnect breaker.

2. Wait for utility voltage to return to

normal.

Generator is still running after switch

transfers to utility power

Engine cool down period. Engine should stop after 1 minute.

Generator or supervised loads (air

conditioner, etc.) are operating

improperly when generator is supplying

power

1. A-A or B-B contacts not operating

correctly.

2. Too much load on generator.

3. Current transformer not connected.

4. Broken current transformer.

1. Check A-A or B-B contacts for

proper operation and/or check

control wiring to external load.

2. Decrease load to generator.

3. Plug CT connectors into control

module.

4. Contact local service center.

Generator is still running after utility

power is restored

1. Minimum engine run time has not

elapsed.

2. Fuse(s) in transfer switch is

defective.

1. Wait five minutes for transfer switch

to retransfer to utility power.

2. Check fuse(s) and replace if

necessary. Replace with fuse of same

type and rating, 600 volt, 2 amp.

Troubleshooting

NOT

FOR

REPRODUCTION

12 BRIGGSandSTRATTON.COM

Transfer Switch Installation Schematic

NOT

FOR

REPRODUCTION

Transfer Switch Installation Diagram

NOT

FOR

REPRODUCTION

14 BRIGGSandSTRATTON.COM

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC TRANSFER SWITCH OWNER WARRANTY POLICY

LIMITED WARRANTY

Briggs & Stratton Power Products Group, LLC will repair or replace, free of charge, any part(s) of the equipment that is defective in material or

workmanship or both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This

warranty is effective for the time periods and subject to the conditions stated below. For warranty service, find the nearest Authorized Service Dealer in

our dealer locator map at BRIGGSandSTRATTON.com.

THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE, ARE LIMITED TO ONE YEAR FROM PURCHASE, OR TO THE EXTENT PERMITTED BY LAW. ANY AND ALL IMPLIED WARRANTIES ARE

EXCLUDED.LIABILITYFORINCIDENTALORCONSEQUENTIALDAMAGESAREEXCLUDEDTOTHEEXTENTEXCLUSIONISPERMITTEDBYLAW.Some

states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not allow the exclusion or limitation

of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you specific legal rights and

you may also have other rights which vary from state to state or country to country.

The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the period of time stated in the

table above. “Consumer use” means personal residential household use by a retail consumer. “Commercial use” means all other uses, including use for

commercial, income producing or rental purposes. Once equipment has experienced commercial use, it shall thereafter be considered as commercial use for

purposes of this warranty. Equipment used for prime power in place of utility are not applicable to this warranty.

NO WARRANTY REGISTRATION IS NECESSARY TO OBTAIN WARRANTY ON BRIGGS & STRATTON PRODUCTS. SAVE YOUR PROOF OF PURCHASE

RECEIPT.IFYOUDONOTPROVIDEPROOFOFTHEINITIALPURCHASEDATEATTHETIMEWARRANTYSERVICEISREQUESTED,THEMANUFACTURING

DATE OF THE PRODUCT WILL BE USED TO DETERMINE THE WARRANTY PERIOD.

ABOUT YOUR WARRANTY

We welcome warranty repair and apologize to you for being inconvenienced. Any Authorized Service Dealer may perform warranty repairs. Most warranty

repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. For example, warranty service would not apply if

equipment damage occurred because of misuse, lack of routine maintenance, shipping, handling, warehousing or improper installation. Similarly, the

warranty is void if the manufacturing date or the serial number on the equipment has been removed or the equipment has been altered or modified. During

the warranty period, the Authorized Service Dealer, at its option, will repair or replace any part that, upon examination, is found to be defective under normal

use and service. This warranty will not cover the following repairs and equipment:

• Normal Wear: Outdoor Power Equipment, like all mechanical devices, needs periodic parts and service to perform well. This warranty does not cover

repair when normal use has exhausted the life of a part or the equipment.

• Installation and Maintenance: This warranty does not apply to equipment or parts that have been subjected to improper or unauthorized installation

or alteration and modification, misuse, negligence, accident, overloading, improper maintenance, repair or storage so as, in our judgment, to adversely

affect its performance and reliability. This warranty also does not cover normal maintenance such as adjustments, cleaning and fuse replacement.

• Other Exclusions: This warranty excludes wear items or damage or malfunctions resulting from accidents, abuse, modifications, alterations, or

improper servicing. Accessory parts are excluded from the product warranty. This warranty excludes failures due to acts of God and other force

majeure events beyond the manufacturers control. Also excluded is used, reconditioned, and demonstration equipment. 198180E, Rev. C, 12/31/2006

Effective November 1, 2005 replaces all undated Warranties and all Warranties dated before November 1, 2005

2 years

None

Consumer Use

Commercial Use

WARRANTY PERIOD

NOT

FOR

REPRODUCTION

Transfer Switch

Specifications

Maximum Load Current:.................... 100 Amps

Rated AC Voltage ..........................250 Volts

Poles.......................................... 2

Frequency ...................................50 Hz

Fault Current Rating ... 25,000 RMS Symmetrical Amperes

Supervisory Contacts Rating:

A-A Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Volt AC

B-B Terminals . . . . . . . . . . 5 Amp, 250 Volt AC, Pilot Duty

Enclosure Type ........................... NEMA 3R

This transfer switch is tested and rated in accordance with UL (Underwriters Laboratories) 1008 (transfer switch equipment).

NOT

FOR

REPRODUCTION

16 BRIGGSandSTRATTON.COM

RESERVED

NOT

FOR

REPRODUCTION

Manual de instalación y del operador

NEMA 3R de 100 amperios

Interruptor de

transferencia automática

con módulo de control de energía

eléctrica de CA

™

NOT

FOR

REPRODUCTION

2 BRIGGSandSTRATTON.COM

Gracias por adquirir este interruptor de transferencia automática para productos eléctricos de Briggs & Stratton. Este

producto está diseñado para usarse con equipos de generador doméstico de reserva de Briggs & Stratton y por lo

tanto puede no funcionar con generadores de otros fabricantes. Un profesional eléctrico calificado puede determinar las

aplicaciones de este equipo con generadores diferentes de los fabricados por Briggs & Stratton. Éste es un sistema de

reserva doméstico opcional que ofrece una fuente alterna de energía eléctrica y suministra cargas como para hornos de gas o

sistemas de refrigeración y comunicación que, cuando dejan de funcionar durante interrupciones de energía, pueden causar

incomodidades o situaciones similares. Este producto no ha sido aprobado como fuente de reserva para casos de emergencia,

según se define en NFPA 70 (NEC).

Este manual contiene información sobre seguridad para que esté consciente de los peligros y riesgos relacionados con

los interruptores de transferencia y cómo evitarlos. Briggs & Stratton ha hecho todo lo posible por ofrecerle un método de

instalación seguro, eficiente y económico. Debido a que cada tarea de instalación es única, es imposible conocer todos los

procedimientos y métodos posibles mediante los cuales se puede realizar la instalación, así como brindar recomendaciones

al respecto. De hecho, no conocemos todos los riesgos posibles ni los resultados de cada método o procedimiento. Guarde

estas instrucciones para futuras consultas.

Este interruptor de transferencia requiere ser instalado antes de usarse. Consulte la sección Instalación de este manual

para obtener instrucciones sobre los procedimientos de instalación. Sólo contratistas de electricidad autorizados deben

instalar interruptores de transferencia. Las instalaciones deben cumplir estrictamente con todos los códigos, las normas

y los reglamentos federales, estatales y locales correspondientes.

Dónde encontrarnos

Nunca tiene que ir demasiado lejos para obtener soporte y servicio de Briggs & Stratton para su interruptor de transferencia.

Existen miles de distribuidores de servicio autorizados de Briggs & Stratton en todo el mundo que ofrecen servicio de

calidad. También puede encontrar a su distribuidor de servicio autorizado más cercano en nuestro mapa de localización de

distribuidores en Internet en BRIGGSandSTRATTON.COM.

Fecha de compra

Interruptor de transferencia

Número de modelo

Revisión del modelo

Número de serie

Milwaukee, WI, USA. Reservados todos los derechos.

Briggs & Stratton Power Products es una marca

registradas de Briggs & Stratton Corporation

Milwaukee, WI, USA

NOT

FOR

REPRODUCTION

Índice

Instrucciones de seguridad importantes ................4

Introducción ...................................5

Para el propietario residencial ...................................5

Orientación para el propietario...................................5

Responsabilidades de la persona encargada de la instalación...........5

Descripción del equipo.........................................5

Instalación ....................................6

Desempaque ................................................6

Pautas de montaje ............................................6

Configuración del sistema ......................................7

Cableado de control de supervisión...............................7

Interconexiones de cableado ....................................8

Controles .................................... 11

Utilización.................................... 11

Evaluación del interruptor de transferencia automática ...............11

Mantenimiento ................................ 11

Resolución de problemas ......................... 12

Esquema de instalación del interruptor de transferencia ..............13

Diagrama de instalación del interruptor de transferencia..............14

Garantía . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Especificaciones ............................... 16

NOT

FOR

REPRODUCTION

4 BRIGGSandSTRATTON.COM

Conserve estas instrucciones

Instrucciones de

seguridad importantes

Éste es el símbolo de alerta de seguridad. Sirve

para advertir al usuario de un posible riesgo para

su integridad física. Siga todos los mensajes de

seguridad que figuren después de este símbolo

para evitar lesiones o incluso la muerte.

El símbolo de alerta de seguridad ( ) se utiliza con una

palabra de señalización (PELIGRO, PRECAUCIÓN,

ADVERTENCIA), una imagen y/o un mensaje de seguridad

para advertir al usuario de un riesgo. PELIGRO indica un

riesgo que, de no evitarse, provocará la muerte o lesiones de

gravedad. ADVERTENCIA indica un riesgo que, de no

evitarse, puede provocar la muerte o lesiones de gravedad.

PRECAUCIÓN indica un riesgo que, de no evitarse, puede

provocar lesiones moderadas. AVISO indica una situación

que podría producir daños en el equipo. Siga en todo

momento los mensajes de seguridad para evitar o reducir el

riesgo de lesiones y de muerte.

Es posible que el fabricante no pueda anticipar cada posible

circunstancia que podría implicar un peligro. Por lo tanto, las

advertencias de este manual y las etiquetas y calcomanías

pegadas a la unidad no incluyen toda la información posible.

Si usa un procedimiento, método de trabajo o técnica de

operación que el fabricante no recomiende específicamente,

debe cerciorarse de que no sea peligroso para usted

y otras personas. También debe asegurarse de que el

procedimiento, método de trabajo o técnica de operación

que elija no provoque que el interruptor de transferencia se

vuelva inseguro.

ADVERTENCIA

Si no conecta el interruptor de transferencia

a tierra adecuadamente, puede ocasionar

electrocución.

• NO toque los cables pelados ni los tomacorrientes.

• NO utilice el interruptor de transferencia con cableado

desgastado, deshilachado, pelado o dañado.

• NO manipule los cables eléctricos si se encuentra en una

zona húmeda, está descalzo o tiene las manos o los pies

mojados.

• Si tiene que trabajar cerca de una unidad mientras está

en funcionamiento, párese en una superficie seca aislada

para reducir el riesgo de descarga eléctrica.

• NO permita que personas no calificadas o niños utilicen

o reparen el interruptor de transferencia.

• En caso de que se presente un accidente por descarga

eléctrica, apague inmediatamente la fuente de energía

eléctrica y comuníquese con las autoridades locales.

Evite el contacto directo con la víctima.

ADVERTENCIA

Sólo electricistas calificados deben intentar instalar

este sistema, lo cual debe cumplir estrictamente

con los códigos, las normas y los reglamentos

correspondientes.

ADVERTENCIA

El alambre de bajo voltaje no se puede

instalar en el mismo conducto que el cableado

de voltaje de energía eléctrica.

• Si no respeta la advertencia anterior, puede provocar

lesiones personales, daños y/o que el equipo funcione

inadecuadamente.

ADVERTENCIA

El interruptor de transferencia contiene

voltaje peligroso que puede provocar lesiones

personales o la muerte.

La instalación o el retiro del transformador de

corriente cuando el generador está funcionando

produce voltaje peligroso que puede provocar

lesiones personales o la muerte.

• A pesar del diseño seguro del interruptor de

transferencia, operar este equipo de forma imprudente,

descuidar su mantenimiento o conducirse de manera

negligente puede provocar posibles lesiones o la muerte.

• NO instale, retire o abra el circuito del transformador

de corriente sin quitar el fusible de 15 amperios del

generador y colocar el interruptor del generador en la

posición OFF.

• Para reducir el riesgo de descarga eléctrica o de lesión

personal, desconecte todas las fuentes de voltaje de

suministro antes de realizar tareas de mantenimiento.

AVISO

El tratamiento inadecuado del interruptor de

transferencia puede dañarlo y acortar su vida productiva.

• Utilice el interruptor de transferencia sólo para los usos

previstos.

• En caso de tener dudas sobre su uso, diríjase a su

distribuidor o póngase en contacto con Briggs & Stratton

Power Products.

• NO exponga el interruptor de transferencia a un exceso

de humedad, polvo, suciedad o vapores corrosivos.

• Permanezca alerta en todo momento mientras trabaja

con este equipo. NUNCA trabaje con el equipo cuando se

encuentre fatigado física o mentalmente.

• Si los dispositivos conectados se sobrecalientan,

apáguelos y apague su disyuntor/fusible.

NOT

FOR

REPRODUCTION

Page is loading ...

Simplicity 071039 User manual

Brand: Simplicity

Model: 071039

Category: Power generators

Type: User manual

Download PDF

report

in other languages

français: Simplicity 071039 Manuel utilisateur
español: Simplicity 071039 Manual de usuario

Simplicity 071039 User manual

Simplicity 071039 User manual

in other languages

Related papers

Other documents