Fanimation Landan FPD8087 Owner's manual

Brand: Fanimation

Model: Landan FPD8087

Category: Household fans

Type: Owner's manual

This manual is also suitable for

FPD8087 Series

Model No. FPD8087**

OWNER'S MANUAL

READ AND SAVE THESE INSTRUCTIONS

The Landan

™

Ceiling Fan

Net Weight 9.91 kg. (21.85 lbs.)

Important Safety Instructions

WARNING: To avoid fire, shock and serious personal injury, follow these instructions.

1. Read your owner’s manual and safety information before installing your new fan. Review the accompanying assembly

diagrams.

2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent

power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a

warning device, such as a tag, to the service panel.

3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off the power to the ceiling

fan before servicing.

4. Do not insert anything into the fan blades while the fan is operating.

5. Do not operate reversing switch until fan blades have come to a complete stop.

Additional Safety Instructions

1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not operate fan without

blades.

2. All wiring and installation procedures must satisfy National Electrical Codes (ANSI/ NFPA 70-1999) and Local Codes. The

ceiling fan must be grounded as a precaution against possible electrical shock. Electrical installation should be made or

approved by a licensed electrician.

3. The fan base must be securely mounted and capable of reliably supporting at least 35 lbs. (fan and accessories not to

exceed 35 lbs. or 15.88 kgs.). See page 4 of owner’s manual for support requirements. Consult a qualified electrician if in

doubt.

4. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the fan blades.

5. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not have adequate

electrical knowledge or experience, have your fan installed by licensed electrician.

6. Suitable for use with solid-state speed controls.

WARNING

To reduce the risk of fire or electric shock, this fan should only be used with Fan Speed Control Part No.

UC7067RYL, manufactured by Rhine Electronic Co., Ltd.

WARNING

TO REDUCE THE RISK OF ELECTRIC SHOCK, THIS FAN MUST BE INSTALLED WITH A GENERAL USE,

ISOLATING WALL CONTROL/SWITCH.

WARNING

This product is designed to use only those parts supplied with this product and/or accessories designated

specifically for use with this product. Using parts and/or accessories not designated for use with this product could result in

personal injury or property damage.

WARNING

To reduce the risk of personal injury, do not bend the blade bracket (flange or blade holder) when installing the

WARNING

Mount to an outlet box marked acceptable for fan support.

brackets, balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades.

LIMITED LIFETIME WARRANTY

Extends to the original purchaser of a Fanimation Fan

1. LIMITED LIFETIME MOTOR WARRANTY - If any part of your fan motor fails, due to a defect in materials or workmanship

during the lifetime of the original purchaser, Fanimation will provide the replacement part free of charge, when the defective

fan is returned to our national service center. Proof of purchase is required. Customer shall be responsible for all costs

incurred in the removal or reinstallation and shipping of the product for repairs or replacement.

2. ONE YEAR MOTOR LABOR WARRANTY - If your fan motor fails at any time within one year from the original purchase, due

to defects in materials or workmanship, labor to repair the motor will be provided free of charge at our national service

center. Purchaser will be responsible for labor charges after this one-year period. Customer shall be responsible for all

costs incurred in the removal or reinstallation and shipping of the product for repairs or replacement.

3. If any other part of your fan fails at any time within one year after original purchase, due to a defect in materials or

workmanship, we will repair, or replace, at our option, the defective part free of charge for parts and labor performed at our

national service center.

4. Because of varying climate conditions, this warranty does not cover changes in the finish, including rusting, pitting,

corroding, tarnishing, or peeling.

5. This warranty is void and does not apply to damage from improper installation, neglect, accident, misuse, exposure to

extremes of heat or humidity, or as a result of any modification to the original product.

6. All costs of removal and reinstallation of the fan are the sole responsibility of the owner of the fan and not the store that

sold the fan or Fanimation.

7. Fanimation reserves the right to modify or discontinue any product at any time and may substitute any part under this

warranty.

8. Under no circumstances may a fan be returned without prior authorization from Fanimation. The receipt of purchase must

accompany authorized returns and must be sent freight prepaid to Fanimation. The fan to be returned must be properly

packed to avoid damage in transit; Fanimation will not be responsible for any damage resulting from improper packaging.

9. It is understood that any repair or replacement is the exclusive remedy available from Fanimation. There is no other

expressed or implied warranty. Fanimation hereby disclaims any and all implied warranties, including, but not limited to

those of merchantability and fitness for a particular purpose to the extent permitted by law. Some states do not allow

limitations on implied warranties. Fanimation will not be liable for incidental, consequential, or special damages arising out

of or in conjunction with product use or performance, except as may otherwise be accorded by law. This warranty gives you

special legal rights and you may also have other rights that vary from state to state.

10.A certain amount of wobble is normal and should not be considered a problem or a defect.

Unpacking Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Energy Efficient Use of Ceiling Fans . . . . . . . . . . . . . . . . . . . . .4

Electrical and Structural Requirements . . . . . . . . . . . . . . . . . .4

How to Assemble Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . .5

How to Hang Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . . .7

How to Wire Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . . .8

How to Install Your Canopy Housing . . . . . . . . . . . . . . . . . . . .9

How to Assembly the Blades & Light Kit . . . . . . . . . . . . . . . .10

How to Operate Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . .12

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

How to Clean Your Ceiling Fan Blades . . . . . . . . . . . . . . . . . .13

How to Replace Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Exploded-View Illustration . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Table of Contents

1. Check to see that you have received the following parts:

If you are uncertain of part description, refer to

exploded view illustration.

This Manual Is Designed to Make it as Easy as Possible for You to Assemble,

Install, Operate and Maintain Your Ceiling Fan

Tools Needed for Assembly

• One Phillips head screwdriver

• One stepladder

• Three wire connectors (supplied)

Installed Wire Length Wire Size A.W.G.

Unpacking Instructions

For your convenience, check-off boxes are provided next to each step. As each step is completed, place a check

mark in the box. This will insure that all steps have been completed and will be helpful in finding your place should

you be interrupted.

Before assembling your ceiling fan, refer to section

on proper method of wiring your fan (page 4). If you

feel you do not have enough wiring knowledge or

experience, have your fan installed by a licensed

electrician.

Do not install or use fan if any part is damaged or

missing. This product is designed to use only those

parts supplied with this product and/or any

accessories designated specifically for use with this

product by Fanimation. Substitution of parts or

accessories not designated for use with this product

by Fanimation could result in personal injury or

property damage.

WARNING

• One wire stripper

• One 1/4” blade

screwdriver

Materials

Wiring outlet box and box connectors must be of type

required by the local code. The minimum wire would be a

3-conductor (2-wire with ground) of the following size:

Up to 50 ft. 14

50-100 ft. 12

Place the parts from the loose parts bags in a small

container to keep them from being lost. If any parts are

missing contact your local retailer.

• Fan Motor Assembly

• Hanger Bracket Assembly

• Hanger Ball / Downrod Assembly

• Ceiling Canopy

• Canopy Screw Cover Assembly

• Blade Holder Set (5)

• Blade Set (5)

• Light Plate Assembly

• LED Down Light Assembly

• Glass

• Remote Hand Held

• Hardware bags:

– Sixteen 3/16-24 x 7.5mm

(blade to blade holder)

Washer Head Screw

– Sixteen 3/16” Fiber Washer

(blade to blade holder)

– Eleven 1/4”-20 x 14mm

(blade arm to motor)

Pan Head Screw

– Phillips Screwdriver, 4”

– Three Wire Connectors

– Balance Kit

– Bag Assembly Safety Cable

Hanger Bracket

Assembly

Hanger Ball / Downrod

Assembly

Fan Motor

Assembly

Ceiling Canopy

Blade Holder Set

Light Plate Assembly LED Down Light

Assembly

Blade Set

Glass

Canopy Screw Cover

Assembly

Remote Hand Held

Hardware Bag

Energy Efficient Use of Ceiling Fans

Ceiling fan performance and energy savings rely

heavily on the proper installation and use of the

ceiling fan. Here are a few tips to ensure efficient

product performance.

Choosing the Appropriate Mounting Location

Ceiling fans should be installed, or mounted, in the

middle of the room and at least 7 feet above the floor

and 18 inches from the walls. If ceiling height allows,

install the fan 8 - 9 feet above the floor for optimal

airflow. Consult your Fanimation Retailer for optional

mounting accessories.

Turn Off When Not in the Room

Ceiling fans cool people, not rooms. If the room is

unoccupied, turn off the ceiling fan to save energy.

Using the Ceiling Fan Year Round

Summer Season: Use the ceiling fan in the

counterclockwise direction. The airflow produced by

the ceiling fan creates a wind-chill effect, making you

“feel” cooler. Select a fan speed that provides a

comfortable breeze, lower speeds consume less

energy.

Winter Season: Reverse the motor and operate the

ceiling fan at low speed in the clockwise direction.

This produces a gentle updraft, which forces warm air

near the ceiling down into the occupied space.

Remember to adjust your thermostat when using your

ceiling fan - additional energy and dollar savings

could be realized with this simple step!

Electrical and Structural Requirements

If your fan is to replace an existing light fixture, turn

electricity off at the main fuse box at this time and

remove the existing light fixture.

Your new ceiling fan will require a grounded electrical

supply line of 120 volts AC, 60 Hz, 15 amp circuit.

The outlet box must be securely anchored and

capable of withstanding a load of at least 50 lbs.

Figure 1 depicts different structural configurations

that may be used for mounting the outlet box.

To avoid fire or shock, follow all wiring instructions

carefully. Any electrical work not described in these

instructions should be done or approved by a

licensed electrician.

Turning off wall switch is not sufficient. To avoid

possible electrical shock, be sure electricity is

turned off at the main fuse box before wiring. All

wiring must be in accordance with National and

Local codes and the ceiling fan must be properly

grounded as a precaution against possible electrical

shock.

WARNING

To reduce the risk of fire, electrical shock, or

personal injury, mount fan to outlet box marked

acceptable for fan support of 15.88 kg (35 lbs) or less.

Use screws supplied with outlet box. Most outlet

boxes commonly used for support of light fixtures

are not acceptable for fan support and may need to

be replaced. Consult a qualified electrician if

in doubt.

WARNING

Figure 1

CEILING

2" x 4"

CEILING JOIST

OUTLET BOX

How to Assemble Your Ceiling Fan

1. Remove the hanger ball portion from the

downrod/hangerball assembly by loosening the set

screw in the hanger ball until the ball falls freely

down the downrod. Remove the pin from the

downrod, then remove the hanger ball. Retain the

pin and hanger ball for reinstallation in Step 4

(Figure 1).

3. Loosen

2. Loosen the two screws in the motor coupler cover

then remove it. Retain the screws and motor coupler

cover for installation in Step 5 (Figure 2).

the two set screws in the downrod support.

Route black and white lead wires through the

downrod (Figure 3).

4. Position downrod support and align the clevis pin

holes in both parts. Install the clevis pin and secure

with the hairpin clip. Tighten the two set screws

and locking nuts in the downrod support (Figure 4).

5. Route wires through motor coupler cover assembly

and tight the two screws from the motor assembly

(Figure 5).

Figure 1

SET SCREW

DOWNROD

HANGER BALL

BLACK AND

WHITE LEADS

DOWNROD

SET SCREWS AND

LOCKING NUTS(2)

Figure 3

Figure 2

Figure 5

DOWNROD

DOWNROD SUPPORT

SCREWDRIVER

SET SCREWS AND

LOCKING NUTS (2)

Figure 4

CLEVIS PIN

HAIRPIN CLIP

6. Route wires through canopy screw cover and

canopy

(Figure 6).

CANOPY

DOWNROD

SET SCREW

GROOVE

HANGER BALL

7. Reinstall the hanger ball on the downrod as

follows.Route the three 80-inch wires through the

hanger ball. Position the pin through the two holes

in the downrod and align the hanger ball so the pin

is captured in the groove in the top of the hanger

ball. Pull the hanger ball up tight against the pin.

Securely tighten the set screw in the hanger ball.

A loose set screw could create fan wobble

(Figure 7).

Figure 7

MOTOR COUPLER

COVER ASSEMBLY

CANOPY SCREW COVER

CANOPY

BLACK &

WHITE LEADS

Figure 6

How to Assemble Your Ceiling Fan (Cont’d)

8. Cut off excess lead wire approximately 6 to 9

inches above top of the top of the downrod. Strip

insulation off 1/2-inch from the end of each lead

wire (Figure 8).

NOTE:

All set screws must be checked, and retightened

where necessary, before installation.

Figure 8

How to Hang Your Ceiling Fan

NOTE: If you are not sure if the outlet box is grounded,

contact a licensed electrician for advise, as it must be

grounded for safe operation.

WARNING

The fan must be hung with at least 7’ of clearance

from ﬂoor to blades. (Figure 10)

Figure 10

CEILING

FLOOR

NO LESS

THAN

7 FEET

WARNING

To avoid possible ﬁre or shock, be sure electricity is

turned off at the main fuse box before hanging.

(Figure 9)

Figure 9

MAIN FUSE BOX

WOOD MEMBER

(2” X 4” APPROX.)

CEILING JOIST

CEILING

JUNCTION

BOX

HANGER BRACKET

CEILING

SUPPORT

CABLE

Figure 11

1. Securely attach the hanger bracket to the outlet box

using the outlet box screws and washers supplied with

the outlet box. (Figure 11)

WARNING

The outlet box must be securely anchored. Hanger

bracket must seat ﬁrmly against outlet box. If the

outlet box is recessed, remove wall board until bracket

contacts box. If bracket and /or outlet box are not

securely attached, the fan could wobble or fall.

2. Drill a ¼” pilot hole into the building structure to

prevent splitting or cracking with installation of the lag

bolt. Using the ” x 2” lag bolt and ﬂat washer, attach

safety cable to ceiling joist or wood structural member.

The lag bolt will pass through the ﬂat washer, safety

cable loop, and into the building structure. (Figure 11)

NOTE: Ceiling support cable cannot be secured to

junction box only, it must be directly secured to ceiling

joist or structural member using the ” x 2” lag bolt

and ﬂat washer. (Figure 11)

3. Make sure the electrical supply wires, including

the hanger bracket grounding wire and safety cable

are pulled through the downrod, between the hanger

bracket and the junction box so that electrical

connections can be made later.

4. Carefully lift the fan and seat the downrod/hanger ball

assembly on the hanger bracket that was just attached to

the outlet box. Be sure the groove in the ball is lined up

with tab on the hanger bracket (Figure 12)

WARNING

Failure to seat tab in groove could cause damage to

electrical wires and possible shock or ﬁre hazard.

WARNING

To avoid possible shock, do not pinch wires between

the hanger ball assembly and the hanger bracket.

5. Attach the safety cable to ceiling support cable. Slide

cable clamp onto safety cable (from fan). Place the end

of cable through the loop of ceiling support cable. Pull as

much cable through loop as possible. Feed end of cable

into clamp hole and ﬁrmly tighten screw (Figure 12).

X 1

HARDWARE USED:

Figure 12

TAB

NOTE: SUPPLY WIRES AND FAN

WIRES OMITTED FOR CLARITY

DOWNROD/HANGER

BALL ASSEMBLY

ATTACH SAFETY

CABLE TO CEILING

SUPPORT CABLE

CEILING SUPPORT

CABLE CLAMP

W/SCREW

How to Wire Your Ceiling Fan

To avoid possible electrical shock, be sure electricity

is turned off at the main fuse box before hanging

(Figure 13).

WARNING

MAIN FUSE BOX

Figure 13

NOTE:

If you are not sure if the outlet box is

grounded, contact a licensed electrician for advice, as

it must be grounded for safe operation.

Figure 14

1. Connect the green grounding lead from the

downrod/hanger ball assembly and the green

grounding lead from the hanger bracket to the supply

grounding conductor (this may be a bare wire or wire

with green colored insulation). Securely connect wires

with wire connectors. Securely connect the white fan

motor wire to the white supply (neutral) wire using

wire connector. Securely connect the black fan motor

wire to the black supply wire using wire connector

(Figure 14).

Green Wire

from Supply

(Ground)

White Wire

from Supply

White Wire

from Fan

Green Wire

from Hanger

Bracket (Ground)

Green Wire

from Hanger

Ball (Ground)

Listed

Outlet Box

Household

Supply

Black Wire

from Supply

Black Wire

from Fan

x 3WIRE

CONNECTORS

HARDWARE USED:

NOTE:

If you feel that you do not have enough electrical

wiring knowledge or experience, have your fan installed

by a licensed electrician.

Check to see that all connections are tight, including

ground, and that no bare wire is visible at the wire

connectors except for the ground wire. Do not

operate fan until the blades are in place. Noise and

motor damage could result.

WARNING

Figure 15

Green Wire

from Supply

(Ground)

White Wire

from Supply

White Wire

from Fan

Green Wire

from Hanger

Bracket (Ground)

Green Wire

from Hanger

Ball (Ground)

Listed

Outlet Box

Household

Supply

Black Wire

from Supply

Black Wire

from Fan

2. After connections have been made, turn leads

upward and carefully push leads into the outlet

box, with the white and green leads to one side

of the box and the black leads toward the

other side. The wires should be spread apart

with the grounded conductor and the

equipment-grounding conductor on one side of

the outlet box and the ungrounded conductor

on the other side of the outlet box. (Figure 15)

1. Remove one of the two shoulder screws in the

hanger bracket. Loosen the second shoulder screw

without fully removing it. Assemble canopy by

rotating key slot in canopy over shoulder screw in

hanger bracket. Tighten shoulder screw. Fully

assemble and tighten second shoulder screw that

was previously removed (Figure 16).

2. Securely attach and tighten the canopy screw

cover over the shoulder screws in the hanger

bracket utilizing the keyslot twist-lock feature

(Figure 17).

How to Install Your Canopy Housing

To avoid possible fire or shock, make sure that the

electrical wires are completely inside the canopy

housing and not pinched between the housing and

the ceiling.

WARNING

CANOPY

SHOULDER

SCREWS (2)

Figure 16

CANOPY COVER

Figure 17

How to Assemble the Blades and Light Kit

x 15

FIBER WASHER

3/16-24 x 7.5mm

WASHER HEAD

SCREWS

HARDWARE USED:

BLADE

3/16-24 x 7.5mm WASHER

HEAD SCREW AND FIBER

WASHER (3 each per blade)

BLADE HOLDER

Figure 18

BLADE HOLDER

1/4-20 x 14mm SCREWS

(2 per assembly)

Figure 19

Figure 20

1. Position the blade over the blade holder with

threaded posts showing. Make sure the bottom

edge of the blade is fully seated against the blade

arm. With a Phillips screwdriver, tighten 3/16-24 x

7.5 mm washer head screws and fiber washers to

secure the blade to the blade arm (Figure 18).

2. Secure the blade holders to the motor support

using the 1/4-20 x 14 mm screws through the holes

located on the side of the motor support (Figure 19).

NOTE:

Periodically check blade holder hardware and

resecure if necessary.

3. Remove one of the three screws in the support

bracket at the bottom of the motor assembly.

Slightly loosen the remaining two screws.

Assemble the light plate assembly to the

support

bracket using the two key slots in the socket

plate. Replace the third screw and securely

tighten all three screws (Figure 20).

Do not connect fan blades until the fan is completely

installed. Installing the fan with blades assembled

may result in damage to the fan blades.

CAUTION

To reduce the risk of electric shock, disconnect the

electrical supply circult to the fan before installing

light kit.

CAUTION

To reduce the risk of personal injury, do not bend the

blade holders when installing, balancing the blades

or cleaning the fan. Do not insert foreign objects in

between the rotating blades.

WARNING

SCREWS (3)

LIGHT PLATE

ASSEMBLY

x 10

1/4-20 x 14mm

SCREWS

HARDWARE USED:

MOTOR

ASSEMBLY

5. Remove three screws in the light plate assembly.

Assemble the LED down light assembly to the light

plate assembly using the three screws and securely

tighten. (Figure 22)

How to Assemble the Blades and Light Kit (Cont’d)

LED DOWN LIGHT

ASSEMBLY

Figure 21

Figure 22

4. Connect the 2-pin connector from the LE D down

assembly light to 2-pin connector from motor

assembly. (Figure 21)

Figure 23

6. Secure the glass to the light plate assembly

by twisting in a clockwise direction.

Do not over-tighten. (Figure 23)

GLASS

LIGHT PLATE

ASSEMBLY

MOTOR ASSEMBLY

SCREWS (3)

LED DOWN LIGHT

ASSEMBLY

How to Operate Your Ceiling Fan

MAIN FUSE BOX

Figure 24

Figure 27

1. Restore electrical power to the outlet box by turning

the electricity on at the main fuse box (Figure 24).

Check to see that all connections are tight, including

ground, and that no bare wire is visible at the wire

connectors, except for the ground wire. Do not

operate fan until the blades are in place. Noise and

fan damage could result.

WARNING

2. To make fan operational, install 23A/12V battery

(included) in hand-held remote transmitter, with fan

power off, arrange code switches to desired code setting.

Then follow the remote code setting process. (If not used

for long periods of time, remove battery to prevent damage

to transmitter). Store the remote away from excessive heat

or humidly (Figure 25).

4. The remote buttons instruct as below:

I = minimum speed II = low speed

III = medium low speed IV = medium speed

V = medium high speed VI = high speed

Button:

This button turns the fan off.

Reverse button (back of remote):

This button is to control fan direction.

Down Light button:

The button is to control light, Infinite light levels

are available by holding the light on/off button

(Figure 27).

Up Light button /

Fan speed:

NOTE:

Receiver in controllers system features an

automatic learning function. There are no frequency

switches on the receiver unit. The receiver will

automatically scan the frequency from the hand held

control if an changes are made. the frequency settings

should be changed only in the case of interference or

if multiple ceiling fans with the same type of control

system are installed in the same structure.

NOTE: If you want to change the blades: turn

the off→ change the blades →turn the power

on →replay the power setting process.

3. Remote Control Setting and Speed (RPM)

Setting Process :

Step 1: Set code switches to desired code.

Turn power on to the fan. Within 60 seconds of

powering the fan on, press and hold the set

button inside the battery compartment of the

remote for 5 seconds. This will synchronize the

control with the fan motor receiver.

Step 2: Speed Setting: After step 1 is complete,

press/release the high speed (VI) button and allo

fan to run for 120 seconds. This will configure th

speeds within the motor electronics.

Step 3: Performing Speed Settings for the reverse

speeds: Press/release the reverse button on the

remote control. Once fan has reversed,

press/release the high speed (VI) button and allo

the fan to run for 120 seconds. (Figure 26).

Now the fan is ready for normal use.

Figure 26

Step 1

Step 3

Step 2

Figure 25

How to Operate Your Ceiling Fan (Cont’d)

How to Replace Receiver

Maintenance

1. Periodic cleaning of your new ceiling fan is the only

maintenance that is needed. When cleaning, use

only a soft brush or lint free cloth to avoid

scratching the finish. Abrasive cleaning agents are

not required and should be avoided to prevent

damage to finish.

Do not use water when cleaning your ceiling fan.

It could damage the motor or the finish and create

the possibility of electrical shock.

CAUTION

Periodic light dusting of the blades is recommended.

A feather duster will work best.

How to Clean Your Ceiling Fan Blades

Avoid using water, cleansers, or harsh rags, which

can warp and ruin the finish.

1. Remove motor coupler cover by unscrewing the

two screws. (Figure 29)

2. Unplug antenna, signal wire and 9-PIN connector then

replace new receiver. (Figure 30)

3. Tight the two screws from the motor coupler cover.

(Figrue 31)

4. After installing new receiver to your fan, operate the

remote “Code Setting” process on “How to operate your

ceiling fan” Step 3 again.

Figure 28

Code Switches

Reverse

Button

Figure 29

Motor Coupler

Cover

Figure 31

Figure 30

Receiver

Signal Wire

9-Pin

Antenna

connector

5. “D” and “ON” dip switch:

The “ON” selection is the light dimmable selection and is to

be used with all bulbs other than CFL. The “D” selection is

the light on only (no dimming function) and is to be used

with CFL bulbs (as CFL bulbs cannot be dimmed). The

receiver provides the following protective function:

(Figure 28)

Lock position: The DC motor has a built-in safety feature

against blade obstruction against obstruction during

operation. If something obstructs the fan blades the motor

will stop operating after 30 seconds of interruption. Please

remove obstacles and reset.

Over 80W protection: When the receiver detects motor

power consumption which is greater than 80W, the

receiver power will shutdown and fan operation will cease.

Disconnect the power supply and after 5 seconds return-

power on to the fan.

Trouble Shooting

For your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan.

WARNING

Trouble Probable Cause Suggested Remedy

1.FAN WILL

NOT START

1. Check main and branch circuit fuses

or circuit breakers.

2. Check line wire connections to fan

and switch wire connections in the

switch housings.

CAUTION: Make sure main power is

turned off !

3. Make sure reversing switch position is

all the way to one side.

4. Replace with fresh battery.

1. Fuse or circuit breaker blown.

2. Loose power line connections to the

fan, or loose switch wire connections

in the switch housing.

3. Reversing switch in neutral position.

4. Dead battery in remote control.

2.FAN SOUNDS NOISY

1. Attach blades to fan before operating.

2. Check to make sure all screws in

motor housing are snug (not over-

tight).

3. Check to make sure the screws which

attach the fan blade holders to the

motor flywheel are tight.

4. Check to make sure wire connectors

in switch housing are not rattling

against each other or against the

interior wall of the switch housing.

CAUTION: Make sure main power is

turned off !

5. Some fan motors are sensitive to

signals from solid-state variable

speed controls. Solid-state controls

are not recommended, choose an

alternative control method.

6. Tighten screws securely.

7. Tighten set screw securely.

1. Blades not attached to fan.

2. Loose screws in motor housing.

3. Screws securing fan blade holders to

motor flywheel are loose.

4. Wire connectors inside housing

rattling.

5. Motor noise caused by solid state

variable speed control.

6. Screws holding blades to blade

holders are loose.

7. Lower housing support set screw

loose.

3.FAN WOBBLES

EXCESSIVELY

1. Tighten both setscrews securely in

downrod support.

2. Tighten the setscrew in the downrod/

hanger ball assembly.

3. Check to be sure screws which attach

the fan blade holders to the flywheel

are tight.

4. Check to be sure the fan blade

holders seat firmly and uniformly to

the surface of the motor housing.

If holders are seated incorrectly,

loosen the screws and retighten.

5. Tighten the hanger bracket screws to

the outlet box, and secure outlet box.

6. Balance blades using balance kit

provided in hardware bag.

1. Setscrew in downrod support is loose.

2. Setscrew in downrod/hanger ball

assembly is loose.

3. Screws securing fan blade holders to

motor hub are loose.

4. Blade holders not seated properly.

5. Hanger bracket and/or ceiling outlet

box is not securely fastened.

6. Fan blades out of balance.

4.NOT ENOUGH AIR

MOVEMENT

1. If possible, consider using a longer

downrod. For example, use a 12”

downrod instead of the 4½” downrod

that comes with your fan.

Parts List

Model No. FP8087**

1 Hanger Bracket Assembly AP255BL

ADRAC1-45**

PG154**

Hanger Ball-Downrod Assembly

Ceiling Canopy3

4 Canopy Screw Cover

AP260**

AP808704**

AP808705**

AP808706**

AP808708

P808709**

TR31

AMA8087**Fan Motor Assembly5

Blade Holder Set6

Blade Set7

Light Plate Assembly8

LED Down Light Assembly

Glass

Remote Hand Held

RECAN125S

Receiver

HDWFPD8087**

—

——

HOW TO ORDER REPAIR PARTS

When ordering repair parts, always give the following information:

• Part Number

• Part Description

• Fan Model Number

Contact your retail store for repair parts.

Before discarding packaging material, be certain all parts have been removed.

** Insert FINISH CODES (Refer to fan model number located on downrod support)

Reference # Description Part #

Balance Kit (BALKT)

Wire Connectors (3)

Bag Assembly Safety Cable

4” Philips Screwdriver

¼”–20 x 14mm Phillips Screws with

Lockwashers (11 pcs)

3/16”–24 x 7.5 mm Washer Head Screws

Washers (16 pcs)

with Fiber

NOTE:

The illustration shown is not to scale or its actual configurations may vary.

* *7808DPF

Exploded-View

11 13

10983 Bennett Parkway

Zionsville, IN 46077

Toll Free (888) 567-2055

FAX (866) 482-5215

Outside U.S. call (317) 733-4113

Fanimation Visit Our Website www.fanimation.com

The Landan

™

Ventilador de techo

Peso neto 9.91 kg (21.85lb)

MANUAL DEL PROPIETARIO

LEA Y GUARDE ESTAS INSTRUCCIONES

Modelo N.º FPD8087**

Page is loading ...

Fanimation Landan FPD8087 Owner's manual

Brand: Fanimation

Model: Landan FPD8087

Category: Household fans

Type: Owner's manual

This manual is also suitable for

FPD8087 Series

Download PDF

report

in other languages

español: Fanimation Landan FPD8087 El manual del propietario

Fanimation Landan FPD8087 Owner's manual

This manual is also suitable for

Fanimation Landan FPD8087 Owner's manual

in other languages

Related papers

Other documents