De Dietrich DOC410XE1 Owner's manual

DOP460*

Le guide d’utilisation de votre four

User Manual for Your Oven

Betriebsanleitung des Backofens

D

e gebruikshandleiding van uw oven

Brugervejledning til ovnen

Guía de utilización del horno

O

guia de utilização do seu forno

FR

GB

DE

NL

DK

ES

PT

ΟΟδδηηγγίίεεςς χχρρήήσσηηςς ττοουυ φφοούύρρννοουυ σσααςς

EELL

99633824_ML.qxp 12/07/2005 16:39 Page 1

2

Tout au long de la notice,

vous signale les consignes de sécurité,

vous signale les conseils et les astuces

Edito P.3

Comment se présente votre four ?

Descriptif de l’appareil P.4

Accessoires P.5

Conseils de sécurité P.6

Comment installer votre four ?

Raccordement électrique P.7

Changement du câble d’alimentation P.8

Dimensions utiles pour encastrer votre four P.9

Comment utiliser votre four ?

Le détail de votre programmateur P.10

Comment mettre à l’heure l’horloge du four ? P.11

Comment faire une cuisson immédiate ? P.12

Comment programmer une cuisson ? P.13

Comment utiliser la minuterie ? P.14

Comment faire une cuisson Economique ? P.15

Comment personnaliser la température de cuisson ? P.16

Comment mettre en veille votre afficheur ? P.16

Comment verrouiller les commandes (sécurité enfants) ? P.16

Comment utiliser EOLYSE P.17

Comment changer l’ampoule ? P.17

Modes de cuisson du four P.18-19

Comment utiliser la fonction ICS ? P.20-27

Comment nettoyer la cavité de votre four ?

Qu’est-ce qu’une pyrolyse ? P.28

Dans quel cas faut-il effectuer une pyrolyse ? P.28

Comment faire une pyrolyse ? P.28-29

Que faire en cas d’anomalies de fonctionnement P.30

Qui contacter ?

P.31

S

ommaire

99633824_ML.qxp 12/07/2005 16:39 Page 2

Page is loading ...

4

Comment se présente votre four ?

1

3

5

Stop / annulation

Réglage de la température

Réglage des durées / fin de

cuisson et mise à l’heure

Sélecteur de fonctions

DESCRIPTIF DE L’APPAREIL

Contact de détection d’ouverture

de porte

Trou pour tourne broche

Indicateur de gradins

Lampe

1

2

3

4

6

7

8

1

2

3

4

5

6

7

8

99633824_ML.qxp 12/07/2005 16:39 Page 4

Page is loading ...

10

Comment utiliser votre four ?

1. Le détail de votre programmateur

1

2

3

4

5

1

2

3

4

5

7

6

8

10

Affichage de l’horloge ou de la minuterie

Affichage des modes de cuisson

Indicateur de gradins et du mode de cuisson choisi.

Affichage des différents programmes de réglage du temps

(durée et fin de cuisson)

Affichage de la température du four

Indicateur de porte verrouillée (lors de la pyrolyse)

Indicateur de la montée en température

Indicateur de minuterie

Indicateurs de pyrolyse

Indicateur de verrouillage clavier(sécurité enfants).

Indicateur de fonction “ICS”

Indicateur de fonction “Eolyse”

9

10

6

7

8

9

11

12

99633824_ML.qxp 12/07/2005 16:39 Page 10

Page is loading ...

Recommandé pour les quiches,

tourtes, tartes aux fruits juteux.

Recommandé pour griller les

côtelettes, saucisses, tranches de

pain, gambas posées sur la grille.

Recommandé pour faire lever les

pâtes à pain, à brioche, kouglof...en

ne dépassant pas 40°C (chauffe-

assiettes, décongélation).

Recommandations

Modes de cuisson du four

Recommandé pour garder le moelleux des

viandes blanches, poissons, légumes

Pour les cuissons multiples jusqu’à 3 niveaux.

Nota : toutes les cuissons se font sans

préchauffage.

Recommandé poursaisir et cuire à coeur

viandes rouges et blanches.

Pour cuire doucement les volailles jusqu’à

2 kg

Préco T°

mini

préco

maxi

35

180

235

mini

préco

maxi

35

205

275

mini

préco

maxi

200

230

mini

préco

maxi

35

275

mini

préco

maxi

35

80

100

180

200

n

ément à la norme européenne EN 50304 et selon la directive Européenne 2002/40/CE.

Recommandé pour les cuissons lentes et

délicates : gibiers moelleux...

Saisir les viandes rouges

Pour mijoter en cocotte fermée les plats

préalablement démarrés sur table de cuis-

son (coq au vin, civet...)

mini

préco

maxi

35

240

275

mini

préco

maxi

30

50

mini

préco

maxi

1

4

mini

préco

maxi

1

2

4

19

FR

99633824_ML.qxp 12/07/2005 16:39 Page 19

Page is loading ...

32

Throughout the manual,

indicates safety recommendations,

indicates advice and tips

Introduction P.33

What does your oven look like?

Description of the appliance P.34

Accessories P.35

Safety recommendations P.36

How do you install your oven?

Electrical connection P.37

Changing the power cable P.38

Useful dimensions for installing your oven P.39

How does your oven work?

Close-up of your analog programmer P.40

How do you set the clock on the oven? P.41

How do you program for immediate cooking? P.42

How do you set a cooking programme? P.43

How do you use the timer? P.44

How do you program an Economical cooking cycle? P.45

How do you customise the cooking temperature? P.46

How do you put your display in standby mode? P.46

How do you lock the controls (child safety device)? P.46

How do you use EOLYSIS? P.47

How do you change the bulb? P.47

Oven cooking modes P.48-49

How do you use the ICS mode? P.50-57

How do you clean the cavity of your oven?

What is pyrolysis? P.58

In what situations should pyrolysis be used? P.58

How do you begin a pyrolysis cycle? P.58-59

What to do in case of operating malfunctions P.60

T

able of Contents

99633824_ML.qxp 12/07/2005 16:40 Page 32

33

GB

Introduction

Dear Customer,

You have just acquired a DE DIETRICH oven and we would like to thank you.

Our research teams have created a new generation of appliances for you. Their

quality, design and technological advances make them exceptional products

and reveal our unique know-how.

With modern, refined lines, your new DE DIETRICH oven blends harmoniously

into your kitchen and perfectly combines technological expertise, cooking per-

formance and aesthetic luxury.

In the line of DE DIETRICH products, you will also find a wide range of hobs,

ventilation hoods, dishwashers, microwave ovens and refrigerators, all of which

can be built in and all of which can be coordinated with your new DE DIETRICH

oven.

Thanks to these "New Items of Value" that serve as guideposts in our every-

day lives, DE DIETRICH, the reference of excellence, is truly an invitation to a

new art of living.

The DE DIETRICH brand.

99633824_ML.qxp 12/07/2005 16:40 Page 33

34

What does your oven look like?

1

3

5

Stop/cancel

Temperature setting

Adjust cooking times/cooking

end time and clock settings

Function selector

DESCRIPTION OF THE APPLIANCE

Contact for open door detector

Hole for rotisserie

Shelf support indicator

Light

1

2

3

4

6

7

8

1

2

3

4

5

6

7

8

99633824_ML.qxp 12/07/2005 16:40 Page 34

GB

Accessories

Rear

Front

Curved anti-tipping safety grid

Its shape was designed to allow you to position

your dish between two shelf support levels.

Dish + grid (drip tray)

Inserted under the grid, it catches barbecue

juices and grease. It can also be used half-full

of water for double-boiler cooling methods.

Avoid placing roasts or meats directly in the

dish because you are certain to have major

spattering on the oven walls

Multi-purpose dish (drip tray)

It is used to collect juices and grease from cook-

ing with the high grill or the pulsed grill. It can be

used as a cooking dish when suitable for the size

of the item to be cooked (e.g. whole poultry sur-

rounded with vegetables, at moderate tempera-

ture). Inserted under the grid, it catches barbe-

cue juices and grease. It can also be used half-

full of water for double-boiler cooking methods.

Rotisserie

• Position the spit support in the notches of the drip

tray dish (see drawing).

• Place the assembly in the oven on the second wire shelf

support (from the bottom). After placing the piece of

meat to be roasted on the rotisserie, place the spit on the

support piece, sliding the whole until the tip of the spit is

inside the motor located at the back of the oven. Remove

the handle by unscrewing it. After cooking, remove the

entire assembly. At the end of the handle, a grip allows

you to unscrew the forks.

Non-stick baking tray

(to be placed on a grid)

Placed on the dish support grid, it can be used for

cooking pastries, pies and pizza.

Its non-stick coating ensures easy removal of

baked items.

Wear oven mitts to protect your hands when

removing it from the oven. Let it cool before

washing it by hand in the kitchen sink with dish soap. Avoid using scouring sponges.

WARNING: Do not cut on it with a knife or a metallic pizza cutter; use plastic or sil-

icone utensils instead.

Do not use the tray at temperatures above 250°C or during the PYROLYSIS mode.

35

99633824_ML.qxp 12/07/2005 16:40 Page 35

36

Safety Recommendations

Please become familiar with these recommendations before installing

and using your oven. This oven was designed for household use only. It is

intended solely for cooking foodstuffs. This oven does not contain any asbestos-

based components.

FIRST USE:

Before using your oven for the first time, heat it up while empty with the door

closed for approximately 15 minutes using the maximum setting in order to “cure”

the appliance. The rock wool that surrounds the oven cavity may initially release

a particular odour caused by its composition. Similarly, you may notice the release

of some smoke. All of this is normal.

SUBSEQUENT USES:

- Ensure that the door of your oven is completely closed so that the seal

can properly do its job.

- Do not let anyone lean against or sit on the oven door when it is open.

- When using the grill with the door semi-open, exposed parts

and surfaces may become hot. Keep small children away.

- When in use, the appliance becomes hot. Be careful not to touch

the heating elements located inside the oven.

- After cooking, do not use bare hands to touch the dishes or accessories

(grid, rotisserie, drip tray, rotisserie support, etc.); use a potholder or heat-resistant

material.

- Do not use a steam cleaner or high-pressure cleaner.

- Do not line your oven with sheets of aluminium. Otherwise, the result

could be an accumulation of heat that could have an undesirable effect on cooking

and roasting results and could damage the enamel.

- The oven must be turned off for all attempts to clean the cavity.

- During pyrolysis, the exposed surfaces become hotter than during

normal use. It is advisable to keep small children at bay.

- Before beginning a pyrolysis cycle, remove all grids and trays.

- If the appliance has an electrical outlet, it must remain accessible

after the appliance has been built in.

99633824_ML.qxp 12/07/2005 16:40 Page 36

37

GB

How do you install your oven?

Monophase 20A Counter

220-240 V ~ 50 Hz

Electrical outlet

2-prong receptacle

+ ground lead

CEI Standard 60083

Monophase line 220-240 V ~

Electrical connection

Power cable

approximately

1.5 m in length

16A fuse or differential

circuit breaker

Before making the connection, ensure that the wires in your elec-

trical installation have enough cross-sectional area to properly

supply electricity to the appliance.

The fuse in your set-up must be 16 amperes.

The electrical connection should be performed before the appliance is installed in

the cabinet.

• The oven must be connected with a power cable (standardised) with three

1.5 mm

2

conductors (1 ph +1 N + ground) that must be connected to a

monophase 220-240 V network via a CEI 60083 standardised receptacle (1 ph +1 N

+ ground lead) or in accordance with installation rules. The safety wire (green-yel-

low) is connected to the appliance's terminal and must be connected to the

ground lead of the electrical set-up.

• In the case of connections with an electric receptacle, it must remain accessible

after installation of the appliance.

• The oven's neutral conductor (blue wire) must be connected to the network's

neutral conductor.

99633824_ML.qxp 12/07/2005 16:40 Page 37

38

• The power cable (H05 RR-F, H05 RN-F or H05 VV-F) must be of sufficient length to

be connected to the build-in oven while it sits on the floor in front of the cabinet.

To do this the appliance must be disconnected from the electrical network:

• Open the inspection flap located at the lower right of the back cover by un-

screwing the two screws, then pivot the inspection flap.

• Strip 12 mm along each wire of the new power cable.

• Carefully twist together the strands.

• Loosen the screws from the terminal board and remove the power cord to be re-

placed.

• Introduce the power cable through the side of the cover in the cable clip located

to the right of the terminal board.

• Connect the power cord wires in accordance with the written markings on the

terminal board.

• All the strands of the electricity wires must be captured under the screws.

• The phase wire on the L terminal.

• The green-yellow coloured ground wire should be connected to the terminal .

• The neutral conductor (blue) on the N terminal.

• Screw down tightly the screws on the terminal board and check the connection

by pulling on each wire.

• Attach the cable with the cable clip located to the right of the terminal board.

o Close the inspection flap using the two screws.

Changing the power cable

We cannot be held responsible for any accident resulting from an

non-existent, defective or incorrect ground lead.

How do you install your oven

99633824_ML.qxp 12/07/2005 16:40 Page 38

39

How do you install your oven?

To be certain that you have properly installed your appliance,

do not hesitate to call on a household appliance specialist.

Useful dimensions for installing your oven

The oven can be installed under a work top or in a column of cabinetry

(open* or closed) having the appropriate dimensions for built-in instal-

lation (see adjacent diagram).

Your oven has optimised air circulation that allows it to achieve remarkable cooking

and cleaning results if the following guidelines are respected:

• Centre the oven in the cabinet so as to guarantee a minimum distance of 5 mm

between the appliance and the neighbouring cabinet.

• The material of the built-in cabinetry must be heat resistant (or be covered with

such a material).

• For greater stability, attach the oven in the cabinet with two screws through the

holes provided for this purpose on either side of the front inner panel (see diagram).

To do this:

1) Remove the rubber screw covers to access the mounting holes.

2) Drill a Ø 3 mm hole in the cabinet panel to avoid splitting the wood.

3) Attach the oven with the two screws.

4) Replace the rubber screw covers (they also serve to absorb the shock caused

by closing the oven door).

(*) If the cabinet is open, its opening must be 70 mm (maximum).

70

550

Location of

retaining screw

50 x 50 mm cut-out

Location of

retaining screw

GB

99633824_ML.qxp 12/07/2005 16:40 Page 39

40

How do you use your oven?

1. Close-up of your programmer

1

2

3

4

5

1

2

3

4

5

7

6

8

10

Clock or timer display

Cooking mode display

Shelf support indicator and selected cooking mode indicator.

Display of various time adjustment programmes (cooking

times and end times)

Oven temperature display

Locked door indicator (during pyrolysis)

Rising temperature indicator

Timer indicator

Pyrolysis indicator

Control lock indicator (child safety device).

“ICS” function indicator

“Eolysis” function indicator

9

10

6

7

8

9

11

12

99633824_ML.qxp 12/07/2005 16:40 Page 40

41

GB

a) When supplied with electricity

• The displays flashes 12:00.

• Program the time by turning the setting

button toward + or - (the speed with which

the button is turned varies the speed with

which the time changes)

Example: 12:30.

Enter the programme by pressing the

selector button.

-> The display stops flashing

b) Resetting the clock time

Press down the button for a

few seconds.

The time display flashes, indicating that

it is now possible to adjust the time.

To set the time, turn the button toward

+ or - so as to advance or turn back the

displayed time.

After entering the time of your choice,

enter it by pushing the button -> the dis-

play stops flashing.

The time cannot be set if the oven is in delayed cooking mode.

In the event of a power outage lasting less than 35 hours, when electricity

is restored, a message indicates that your oven will automatically readjust

the time displayed.

2.

How do you set the clock on the oven?

How does your oven work?

99633824_ML.qxp 12/07/2005 16:40 Page 41

42

How does your oven work?

The analogue programmer should display only the time; it should not be flashing.

• Press and turn the button toward the right to select the cooking mode.

The selection function flashes.

• Enter the time by pressing the setting button.

The cooking mode indicator stops flashing and

the recommended temperature begins flashing.

When the pre-selected temperature appears, the

shelf support indicator and the heating elements

in use also light up. The oven begins heating.

Place your dish in the oven based on the sug-

gestion indicated in the display and the recom-

mendations provided in the cooking guide.

Example: “ -> Shelf support 2 or 3

recommended.

As long as the °C symbol is flashing, you can

make changes by turning the temperature selec-

tor button.

Enter the time by pressing the button.

Your oven recommends the optimal temperature

for the chosen dish. It is, however, possible to

adjust the temperature at any time by using the

“ ” touch control located under the display.

Example “ ” adjusted to 210°.

After these three steps, the oven heats up:

- These rising temperature indicator symbols indicate the incremental temper-

ature increase inside the oven.

- A series of beeps will indicate that the oven has reached the selected temperature.

To stop cooking, press and hold the STOP touch control for a few seconds.

After a cooking cycle, the circulating fan continues to function for a

period in order to cool the oven.

3. How do you program for immediate cooking?

99633824_ML.qxp 12/07/2005 16:40 Page 42

43

GB

How does your oven work?

4. How do you set a cooking programme?

b)

W

ith delayed start (choose end time)

Proceed as with programmed cooking.

After setting the cooking time, press

two times so that the end time begins flashing.

Turn the selector button toward + or - to

set the desired end of cooking time.

Enter the time by pressing the button.

After these steps, the oven heating is

delayed so that cooking ends at 13:00.

When your cooking programme is finished, a

three-beep pattern will be emitted for a few

minutes. The beeps will stop automatically.

a) With immediate start

Proceed as described in the “Immediate Cooking” section.

Press the button.

The cooking time flashes 0:00 to indicate that

it is now possible to set it.

Turn the button to set the desired time.

Example: 25 min cooking time.

Enter by pressing the button.

The cooking time starts counting down as

soon as the time has been entered. You can

cancel the function at any time by setting

the displayed value to 0 (after having

pressed the touch control ).

99633824_ML.qxp 12/07/2005 16:40 Page 43

44

How does your oven work?

5. How do you use the timer?

Your oven is equipped with an electronic timer that is independent of the

oven functions, making it possible to measure times.

In this case, the timer display takes priority over the time of day display.

Press the touch control three times.

The hourglass appears and

00

M00S flashes.

Turn the button until you obtain the desired

length of time (max 59 minutes and 59 seconds)

Enter the time by pressing the button.

The display stops flashing and the timer starts working, counting down the time in

seconds. When the cooking time is finished, the timer starts beeping to alert you

and the hourglass begins flashing.

It is possible to change or cancel the timer programme at any time

by turning it to 0 and pressing the button to enter.

99633824_ML.qxp 12/07/2005 16:40 Page 44

45

6. How do you program for energy-saving cooking?*

After a cooking cycle, the circulating fan continues to function

for a period to ensure the heating elements are properly

cooled down.

The analogue programmer should display only the time; it should not be flashing.

Turn the selector button to the

cooking mode.

Enter the time by pressing the button.

• Place your dish in the oven based on the recommendation indicated in the display.

• Your oven recommends the optimal temperature for the chosen cooking mode:

200°C.

It is, however, possible to adjust the temperature by using the button located

under the display.

Example: "ECO Cooking" position adjusted to 190°C

After these three steps, the oven heats up:

The temperature rise indicator is activated and signals the incremental

temperature increase in the oven.

Three beeps will indicate to you that the set temperature has been reached.

To optimise the ECO cooking mode, do not pre-heat and do not open

the door during cooking.

*This position makes it possible to save up to 20% energy while still

offering identical cooking results.

The ECO position is used for the energy label performance.

How does your oven work?

GB

99633824_ML.qxp 12/07/2005 16:40 Page 45

46

You can adjust the brightness of your display. To do this:

- Set the time of your programmer to 12:10.

- Depress the “ ” button while rotating it (+ or -) in order to obtain the desired

level of brightness.

- After having adjusted the brightness to your liking, return your programmer to

the current time of day.

8.

Adjusting brightness

How does your oven work?

7. Customising the recommended temperature

Select the cooking function:

If you wish to customise the recommended temperature:

- Press the “ ” touch control until the temperature display begins flashing.

- Turn the + or - button until the desired temperature appears.

- Press to enter.

9. Control panel locking (child safety device)

You have the option of preventing access to the oven controls by taking the fol-

lowing steps:

When the oven is off, hold down the STOP

touch control for a few seconds; a “key” will

then be displayed on the screen -> access to

the oven controls is now blocked.

To unlock access, hold down the STOP touch

control for a few seconds.

The oven controls are once again accessible.

You cannot lock the oven if you have programmed a cooking cycle.

99633824_ML.qxp 12/07/2005 16:40 Page 46

Page is loading ...

De Dietrich DOC410XE1 Owner's manual

De Dietrich DOC410XE1 Owner's manual

in other languages

Related papers

Other documents