Craftsman Lawn Mower Accessory 358.792441 User manual

Category
Grass trimmers
Type
User manual
Instruction Manual
BRUSHCUTTER ATTACHMENT
Model No,
358.792441
NOT DESIGNED FOR USE
WITH ELECTRIC POWERHEADS
Safety
Assembly
Operation
Maintenance
Parts List
Espa_ol
DANGER:
Read and follow all Safety Rules and Operating
Instructions before first use of this product.
For answers to your questions about this product: Call 7
am-7 pm, Mon.-Sat., or 10 am-7 pm, Sun.
1-800-235-5878 <.o°,, listed are Central Time)
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
530164038 4/23/03
Warranty Statement 2 Service & Adjustments 14
Identification of Symbols 2 Storage 15
Safety Rules 2
Parts List 16
Assembly 5
Operation 10 Spanish 17
Maintenance 14 Parts and Ordering Back Cover
FULL ONE YEAR WARRANTY ON CRAFTSMAN® BRUSHCUTTER ATTACHMENT
For one year from the date of purchase, when this Craftsman Brushcutter Attach-
ment is maintained and lubricated according to the operating and maintenance
instructions in this manual, Sears will repair, free of charge, any defect in materi-
als or workmanship.
This warranty excludes expendable parts that become worn during normal use.
Ifthis Craftsman Brushcutter Attachment is used for commercial purposes, this war-
ranty applies for only 90 days from the date of purchase. If this Craftsman Brushcut-
ter Attachment is used for rental purposes, this warranty applies for only 30 days from
the date of purchase.
This warranty applies only while this product is in use in the United States.
WARRANTY SERVICE ISAVAILABLE BY RETURNING THE CRAFTSMAN BRUSHCUT-
TER ATTACHMENT TO THE NEAREST SEARS STORE OR SERVICE CENTER IN THE
UNITED STATES.
This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
Sears, Roebuck and Co., I)/817 WA, Hoffman Estates, IL 60179
DANGER! This brushcutter
can be dangerous! Careless or
improper use can cause
serious or even fatal injury,
Read and understand the
instruction manual before
using the brushcutter.
[_ Always wear appropriate ear protection, eye protection and head protection.
DWARNING: When using garden-
ing appliances, basic safety precau-
tions should always be followed to re-
duce the risk of fire and serious injury.
Read and follow all instructions. Fail-
ure to do so can result in serious injury.
DANGER: This power tool can be
dangerous! This unit can cause seri-
ous injury including amputation or
blindness to the operator and others.
The warnings and safety instructions
in this manual must be followed to pro-
vide reasonable safety and efficiency
in using the unit. The operator is re-
sponsible for following the warnings
and instructions in this manual and on
the unit. Read the entire instruction
manual before assembling and using
the unit[ Restrict the use of this unit to
persons who read, understand, and
follow the warnings and instructions in
this manual and on the unit. Never al-
low children to operate this unit.
INSTRUCTION SAFETY INFORMATION
MANUAL ON THE UNIT
_l_ DANGER: Never use flailing de-
vices.
_l_ DANGER: Blade can thrust vio-
lently away from material it does not
cut. Blade thrust can cause amputa-
tion of arms or legs. Keep people and
animals 50 feet (15 meters) away.
_I_WARNING: Blade/trimmer line
can throw objects violently. You can be
blinded or injured. Wear eye and leg
protection.
ALWAYS WEAR:
_ Eye
Protection
mt Leg
Guards
I_ Boots
_I_WARNING: Hazard zone for
thrown objects. Blade/trimmer line can
throw objects violently. Others can be
blinded or injured. Keep people and
animals 50 feet (15 meters) away.
d Zone
all.WARNING: Do not use trimmer
head as a fastening device for the
blade.
_1_WARNING: The blade continues
to spin after throttle is released or en-
gine is turned off. The coasting blade
can throw objects or seriously cut you
if accidentally touched. Stop the blade
by contacting the left hand side of
coasting blade with material already
cut.
Stop coasting _ ___._
blade bycontact _.,.,,_r
with cut material.
OPERATOR SAFETY
° Dress properly. Always wear safety
glasses or similar eye protection
when operating, or performing main-
tenance on your unit (safety glasses
are available). Eye protection should
be marked Z87.
* Always wear face or dust mask if op-
eration is dusty.
* Always wear heavy, long pants, long
sleeves, boots, and gloves. Wearing
safety leg guards is recommended.
* Always wear foot protection. Do not
go barefoot or wear sandals. Stay
clear of spinning line/blade.
* Secure hair above shoulder length.
Secure or remove loose clothing and
jewelry or clothing with loosely hang-
ing ties, straps, tassels, etc. They
can be caught in moving parts.
* Being fully covered also helps pro-
tect you from debris and pieces of
toxic plants thrown by spinning line/
blade.
* Stay Alert. Do not operate unit when
you are tired, ill, upset or under influ-
ence of alcohol, drugs, or medica-
tion. Watch what you are doing; use
common sense.
* Wear hearing protection.
3
Neverstartorruntheengineinsidea
closedroomorbuilding.Breathing
exhaustfumescankill.
Keephandlesfreeofoilandfuel.
Alwaysusethehandlebaranda
properly adjusted shoulder strap
when using brushcutter attachment
(see ASSEMBLY).
UNIT/MAINTENANCE SAFETY
_l_ WARNING: Disconnect power-
head spark plug (or disconnect power-
head from power source) before per-
forming maintenance.
Look for and replace damaged or
loose parts before each use. Look
for and repair fuel leaks before use.
Keep unit in good working condition.
Throw away blades that are bent,
warped, cracked, broken, or dam-
aged in any other way. Replace trim-
mer head parts that are cracked,
chipped, broken, or damaged in any
other way before using the unit.
Maintain the unit according to recom-
mended procedures. Keep the blade
sharp. Never use flailing devices,
wire, rope, string, etc.
Use only specified blade or trimmer
head; make sure it is properly in-
stalled and securely fastened.
Never start engine with clutch shroud
removed. The clutch can fly off and
cause serious in ury.
Be sure bade or tr mmer head stops
turning when engine idles.
Make carburetor adjustments with the
lower end supported to prevent the
blade or trimmer line from contacting
any object. Hold the unit by hand; do
net use the shoulder strap for support.
Keep others away when making car-
buretor adjustments.
Use only recommended Craftsman
accessories and replacement parts.
Have all maintenance and service
not explained in this manual per-
formed by a Sears Service Center.
FUEL SAFETY
Mix and pour fuel outdoors.
Keep away from sparks or flames.
Use a container approved for fuel.
Do not smoke or allow smoking near
fuel or the unit or while using the unit.
Avoid spilling fuel or oil. Wipe up all
fuel spills before starting engine.
Move at least 10 feet (3 meters) away
from fueling site before starting engine.
Stop engine and allow it to cool be-
fore removing fuel cap,
Remove fuel cap slowly,
CUTTING SAFETY
_II'I_,wARNING: Inspect the area to be
cut before each use. Remove objects
(rocks, broken glass, nails, wire, string,
etc.) which can be thrown or become
entangled in the blade or trimmer line.
Keep others including children, ani-
mals, bystanders, and helpers at
least 50 feet (15 meters) away. Stop
the engine immediately if you are ap-
proached.
Always keep engine on the right-
hand side of your body.
Hold the unit firmly with both hands.
Keep firm footing and balance. Do
not overreach.
Keep blade/trimmer head below
waist level.
Do net raise powerhead engine above
your waist.
Keep all parts of your body away
from spinning blade/line and muffler.
Cut from your left to your right. CUt-
ting on right side of shield will throw
debris away from the operator.
Use only in daylight or good artificial
light.
Use only for jobs explained in this
manual.
TRANSPORTING AND STORAGE
Stop the powerhead engine before
carrying unit.
Keep muffler away from your body.
Allow engine to cool and secure unit
before storing or transporting it in a
vehicle.
Empty the fuel tank before storing or
transporting the unit. Use up fuel left
in the carburetor by starting the en-
gine and letting it run until it stops.
Store unit and fuel in an area where
fuel vapors cannot reach sparks or
open flames from water heaters,
electric motors or switches, furnaces,
etc.
Store unit so the blade or line limiter
blade on shield cannot accidentally
cause in ury.
Store un t ndoors, out of reach of
children.
SPECIALNOTICE:Exposuretovibra-
tionsthroughprolongeduseofgasoline
poweredhandtoolscouldcauseblood
vesselornervedamageinthefingers,
hands,andointsofpeoplepronetocir-
cuatondsordersorabnormaswerigs.
Prolongeduseincoldweatherhasbeen
linkedtobloodvesseldamageinother-
wisehealthypeople.Ifsymptomsoccur
suchas numbness, pain, loss of
strength, change in skin color or texture,
or loss of feeling in the fingers, hands, or
joints, discontinue the use of this tool
and seek medical attention. An anti-
vibration system does not guarantee the
avoidance of these problems. Users
who operate power tools on a continual
and regular basis must monitor closely
their physical condition and the condition
of this tool.
SAVE THESE INSTRUCTIONS
CARTON CONTENTS
Check carton contents against the fol-
lowing list.
Model 358.792441
Brushcutter Attachment
Handlebar (with Clamp and Knob)
Handlebar Clamp Base (with Spacer
Tabs)
Shoulder Strap
Upper Shoulder Strap Clamp
Lower Shoulder Strap Clamp (with
Spacer Tabs)
Handlebar Clamp Screws (4)
Shoulder Strap Clamp Screws (2)
Large nut for installing blade
Cupped washer
Trimmer head
4-point weed blade (assembled on
brushcutter attachment)
Wing nut (screwed onto shield)
Metal shield (assembled on brush-
cutter attachment)
Plastic shield
Attachment Hanger
Hex Wrench
Container of line
Examine parts for damage. Do not use
damaged parts.
NOTE: If you need assistance or find
that parts are missing or damaged, call
1-800-235-5878.
ASSEMBLY
=-&
all, WARNING: If received assembled,
repeat all steps to ensure your unit is
properly assembled and all fasteners
are secure.
A hex wrench (provided) is required
for assembly.
INSTALLING BRUSHCUTTER AT-
TACHMENT
CAUTION: When removing or instal-
ling attachments, place the unit on a
flat surface for stability.
1. Loosen the coupler by turning the
knob counterclockwise.
Coupler
LOOSEN
2,
3.
4.
5.
TIGHTEN Knob
Remove the tube cap from the
brushcutter attachment (if present).
Position locking/release button of
attachment into guide recess of
coupler.
Push the attachment into the cou-
pler until the locking/release button
snaps into the primary hole.
Before using the unit, tighten the
knob securely by turning clock-
wise.
Coupler Primary Hole
\ /Guide Recess
Up!er L°ckin_g/[_
Tube Release Attachment
Button
all}WARNING: Make sure the lock-
ing/release button is locked in the pri-
mary hole and the knob is securely
tightened before operating the unit.
HANDLEBAR ASSEMBLY
DANGER: RISK OF CUT To
avoid serious injury, the barrier portion of
the handlebar must be installed as
shown on the upper tube of the power-
head to provide a barrier between op-
erator and the spinning blade. Attach
tube clamp above arrow on safety warn-
ing decal on the upper tube (powerhead
end of unit). Ensure handlebar is posi-
tioned on handlebar clamp between the
arrows on the handlebar decal.
5
NOTE:Thetubeclampbasehasfour
spacertabsattached.Thesetabsare
providedtoadaptthisattachmentfor
usewithpowerheadsthathavea1"di-
ameteruppertube(thetubeclampwill
nottightendownsecurelyonthe1"di-
ameteruppertubewithoutusingthese
spacertabs).Thetabsmustbebroken
offcompletelybeforeuseandplaced
overthescrewholesontheclampbase.
Thesetabsarenotneededforpower-
headswitha7/8"uppertube.
HANDLEBARCLAMPBASE
SpacerTabs
SpacerTabs_
o °ai i° e rer ae
upper tube _I
1. Place the tube clamp over the upper
tube above the arrow on the safety
decal.
2. Position the clamp base under the
upper tube and align the tube clamp
and clamp base screw holes (use
spacer tabs between tube clamp
and clamp base if necessary to se-
cure clamp, i.e. for 1" diameter up-
per tube).
Handlebar
POWERHEAD
END
Handlebar Clamp
between arrows on
handlebar decal
Clam
Knob
Clamp Screws
Arrow on
Safety Decal
ATTACHMENT END
3. Insert four screws into the screw
holes.
4. Secure tube clamp by tightening
screws with the hex wrench.
5. Position the handlebar as shown,
ensuring the handlebar is posi-
tioned on the handlebar clamp be-
tween the two arrows on the han-
dlebar decal.
6. Retighten handlebar byturning
clamp knob clockwise until handle-
bar is secure and stationary in
clamp (clamp knob cannot be
overtightened).
SHOULDER STRAP ASSEMBLY
_1_WARNING: Proper shoulder
strap and handlebar adjustments must
be made with the engine completely
stopped before using unit. The shoul-
der strap clamp must be installed as
shown above the handlebar on the up-
per tube (powerhead end of unit).
NOTE: The lower shoulder strap clamp
has two spacer tabs attached. These
tabs are provided to adapt this attach-
ment for use with powerheads that have
a 1" diameter upper tube (the shoulder
strap clamp will not tighten down se-
curely on the 1" diameter upper tube
without using these spacer tabs). The
tabs must be broken off completely be-
fore use and placed over the screw
holes on the lower shoulder strap clamp.
These tabs are not needed for power-
heads with a 7/8" upper tube.
LOWER SHOULDER STRAP
CLAMP
Spacer Tabs_'r _
.,dC_L.4--_ _- Spacer Tabs
I1_-_ positioned for use
on 1" diameter
upper tube
1,
2.
Place the upper shoulder strap
clamp over the upper tube above
the handlebar.
Position the lower shoulder strap
clamp under the upper tube and
align the upper and lower clamp
screw holes (use spacer tabs be-
tween upper and lower clamps if
necessary to secure clamp, i.e. for
1" diameter upper tube).
POWERHEAD
END
!Clamp
30 inches
I ATTACHMENT
Lower Shoulde
END
Strap Clamp
o
3. Insert two screws into the screw
holes.
4. Secure shoulder strap clamp by
tightening screws with the hex
wrench.
5. Insert your right arm and head
through the shoulder strap and al-
low it to rest on your left shoulder.
Make sure the danger sign is on
your back and the hook is to the
right side of your waist.
NOTE: A one-half twist is built in the
shoulder strap to allow the strap to rest
flat on the shoulder.
6. Adjust the strap, allowing the book
to be about 6 inches below the
waist.
7. Fasten the strap hook to the clamp
and lift the tool to the operating
position.
8. Try on shoulder strap and adjust
for fit and balance before starting
the engine or beginning a cutting
operation.
NOTE: It may be necessary to relo-
cate the shoulder strap clamp on the
shaft for proper balancing of unit.
HARNESS
ADJUSTMENT
FOR BALANCE
6 inches
below
waist
4 - 12
inches
above
ground
CONFIGURING YOUR UNIT
You can configure your unit using a trim-
mer head for grass and light weeds, or a
weed blade for cutting grass, weeds,
and brush up to 1/2 inch in diameter. To
assemble your unit, go to the section for
the desired configuration and follow the
instructions.
ASSEMBLY INFORMATION -
TRIMMER HEAD
TRIMMER
HEAD
NOTE: Remove the blade and metal
shield before attaching the plastic shield
and trimmer head. To remove blade,
align hole in the dust cup with the hole
in the side of the gearbox by rotating
the blade. Insert a small screwdriver
into aligned holes. This will keep the
shaft from turning while loosening the
blade nut. Remove blade nut by turning
clockwise. Remove the screwdriver.
Remove both washers and blade. To
remove metal shield, loosen and re-
move the four mounting screws. See AT-
TACHINGTHE METALSHIELD and
INSTALLATIONOF THE METALBLADE for
illustrations. Be sure to store all parts
and instructions for future use.
INSTALLATION OF THE TRIMMER
HEAD
NOTE: Before installing the trimmer
head, make sure the dust cup and re-
taining washer are positioned on the
shaft of the gearbox, The retaining
washer must be positioned with the
raised section toward the gearbox,
1, Alignholeinthedustcupwiththe
holeinthesideofthegearboxby
rotatingthedustcup.
2, Insertasmallscrewdriverinto
alignedholes,Thiswillkeepthe
shaftfromturningwhiletightening
trimmerhead,
3,
While holding the screwdriver in
position, thread trimmer head onto
the shaft by turning counterclock-
wise. Only tighten hand tightt
Gearbox
Dust Cup
Tnmmer Head _ Retaining
Washer
J
4, Removethe screwddver,
ATTACHING THE PLASTIC SHIELD
_WARNING: The shield must be
properly installed. The shield provides
partial protection from the risk of
thrown ob ects to the operator and oth-
ers and sequppedwtha ne mter
blade which cuts excess line to the
proper length. The line limiter blade
(on underside of shield) is sharp and
can cut you.
1. Remove wing nut from shield.
2. Insert bracket into slot on shield.
3. Pivot shield until bolt passes
through hole in bracket.
4. Tighten the wing nut securely.
Slot Bracket \ &:o_
Shield _*_ W_iingNut
_Gearbo_
ASSEMBLY INFORMATION - WEED
BLADE
_lb WEED
BLADE
NOTE: Remove the trimmer head and
plastic shield before attaching the metal
shield and installing the weed blade. To
remove the trimmer head, align hole in
the dust cup with the hole in the side of
the gearbox by rotating the dust cup.
Insert a small screwdriver into aligned
holes. This will keep the shaft from turn-
ing while loosening the trimmer head.
Remove the trimmer head by turning
clockwise. Remove the screwdriver. To
remove the plastic shield, loosen and
remove wing nut. Pivot shield to release
bracket from slot. See INSTALLATIONOF
THE TRIMMERHEADand ATTACHING
THE PLASTICSHIELD for illustrations. Be
sure to store all parts and instructions for
future use. Never use the trimmer head
with the metal blade installed.
ATTACHING THE METAL SHIELD
_I_WARNING: The metal shield
must be properly installed on the tool
anytime the tool is used with a blade.
The forward tip of the metal shield
helps to reduce the occurrence of
blade thrust which can cause serious
injury such as amputation to the opera-
tor or bystanders. Failure to install the
shield in the position shown can result
in serious injury to the operator. The
length of the shield must be aligned
with the length of the tube.
1. Place the metal shield under the
gearbox, and align the screw holes.
Gearbox
Shield
2, Insertandthreadthe4mounting
screwsthroughtheholesofthe
_earboxandthemetalshield.
ightenevenlyandsecurelywith
thehexwrenchprovided,
INSTALLATION OF THE METAL
BLADE
_l_ WARNING: Wear protective
gloves when handling or performing
maintenance on the blade to avoid in-
jury. The blade is sharp and can cut
you even when it is not moving.
_I_WARNING: Do not use any
blades, or fastening hardware other than
the washers and nuts shown in the fol-
lowing illustrations. These parts must be
provided by Sears and installed as
shown below. Failure to use proper parts
can cause the blade to fly off and seri-
ously hurt you or others.
NOTE: The dust cup and retaining
washer are located on the gearbox shaft
and not in the parts bag. All other fas-
teners mentioned in the following as-
sembly steps are in the parts bag.
1. Remove the retaining washer from
the threaded shaft of the gearbox.
Leave the dust cup on the shaft.
2. Install the blade and the retaining
washer over the threaded shaft.
3. Make sure the raised part of the re-
taining washer is facing the gearbox
and the raised area fits into the hole
in the center of the blade.
4. Slide the blade and retaining
washer onto the shaft of the gear-
box.
5. Place the cupped washer onto the
shaft. Make sure the cupped side
of the washer is toward the blade.
6. Install the blade nut by threading
onto the shaft counterclockwise.
Gearbox
Shield
\
Dust Cu Threaded Shaft
Blade
Retaining
Washer ---_
Cupped__
Washer
_",_-_ Nut
NOTE: Make sure all parts are in place
as illustrated, and the blade is sand-
wiched between the dust cup and the
retaining washer. There should be no
space between the blade and the dust
cup or the retaining washer.
7. Align hole in dust cup with hole in
side of gearbox by rotating the
blade.
8. Insert a small screwdriver into
aligned holes. This will keep the
shaft from turning while tightening
the blade nut.
9. Tighten blade nut firmly with a
wrench while holding screwdriver
in position.
10. Remove the screwdriver.
11. Turn blade by hand. If the blade
binds against the shield, or ap-
pears to be uneven, the blade is
not centered, and you must rein-
stall.
NOTE: To remove blade, insert screw-
driver into aligned holes. Unthread the
nut and remove parts. Be sure to store
parts and instructions for future use.
KNOW YOUR BRUSHCUTTER ATTACHMENT
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR
BRUSHCUTTER ATTACHMENT. Compare the illustrations with your unit to familiarize
yourself with the location of various controls and adjustments, Save this manual for
future reference,
_T_ Hanger
be
Trimmer Shield
_'-_ Blade
Blade Shield
BLADE
The BLADE is designed for cutting
grass, weeds, and brush up to 1/2 inch
m diameter.
TRIMMER HEAD
The TRIMMER HEAD holds cutting line
and is designed for cutting grass and
light weeds.
BLADE SHIELD
The BLADE SHIELD provides protection
from the spinning blade.
TRIMMER SHIELD
The TRIMMER SHIELD provides protec-
tion from the spinning trimmer head.
OPERATING THE COUPLER
Your powerhead is equipped with a
coupler which enables optional attach-
ments to be installed. The optional at-
tachments are:
Edger ............... 358.792401
Cultivator ............ 358.792410
Blower .............. 358.792421
WARNING: Always disconnect
powerhead spark plug before remov-
ing or installing attachments.
REMOVING BRUSHCUTTER AT*
TACHMENT (OR OTHER OPTIONAL
ATTACHMENTS)
CAUTION: When removing or instal-
ling attachments, place the powerhead
and attachment on a flat surface for
stability.
1. Loosen the coupler by turning the
knob counterclockwise.
Upper Tube
Coupler
Lower \ LOOSEN
Attachment
TIGHTEN Knob
2. Press and hold the locking/release
button.
Lower Attachment
UpperTube
3. While securely holding the upper
tube, pull the attachment straight
out of the coupler.
10
INSTALLINGOPTIONAL ATTACH*
MENT
1. Remove the tube cap from the at-
tachment (if present)and discard.
2. Position locking/release button of
attachment into guide recess of
upper tube coupler.
Coupler Primary Hole
Upper Locking/ Attachment
Tube Release
Button
3. Push the attachment into the cou-
pler until the locking/release button
snaps into the primary hole.
4. Before using the unit, tighten the
knob securely by turning clock-
wise.
INSTALLING ATTACHMENT
HANGER
An attachment hanger is provided for
storage when attachment is not in use.
To install hanger on attachment:
1. Remove the tube cap from the at-
tachment (if present) and discard.
2. Press and hold the locking/release
button.
3. Push hanger onto the attachment
until the locking/release button
snaps into the hole.
OPERATING POSITION
ALWAYS WEAR:
Heavy,
Long Pants
Boots _,.
_ Protection
NOTE: This brushcutter attachment is
not designed for use with electric pow-
erheads.
When operating unit with brushcutter
attachment, clip shoulder strap onto
upper shoulder strap clamp, stand as
shown and check for the following:
Wear eye protection and heavy
clothing.
Keep arms extended with right hand
holding the trigger handle of power-
head.
Keep left arm extended with left hand
holding the handlebar.
Keep unit below waist level.
Shoulder strap pad should be cen-
tered on your left shoulder and dan-
ger sign centered on your back.
Maintain full weight of tool on left
shoulder.
Without bending over, keep the blade
near and parallel to the ground and
not crowded into material being cut.
OPERATING INSTRUCTIONS FOR
USE OF BRUSHCUTTER ATTACH*
MENT WITH TRIMMER HEAD
_l_ WARNING: Always wear eye
protection. Never lean over the trim-
mer head. Rocks or debris can rico-
chet or be thrown into eyes and face
and cause blindness or other serious
injury.
Before trimming, bring engine to a
speed sufficient to cut material to be
trimmed.
De net run the engine at a higher speed
than necessary. The cutting line will cut
efficiently when the engine _srun at less
than full throttle. At lower speeds, there
is less engine noise and vibration. Al-
ways release the throttle trigger and
allow the engine to return to idle speed
when not cutting.
CUTTING METHODS
_I_WARNING: Use minimum speed
and do not crowd the line when cutting
around hard objects (rock, gravel,
fence posts, etc.), which can damage
the trimmer head, become entangled
in the line, or be thrown causing a seri-
ous hazard.
The tip of the line does the cutting.
You will achieve the best perform-
ance and minimum line wear by not
crowding the line into the cutting
area. The right and wrong ways are
shown below.
Tip of line does the
Right
Line crowded into
i Wrong
11
*The line will easily remove grass and
weeds from around walls, fences,
trees and flower beds, but it also can
cut the tender bark of trees or shrubs
and scar fences.
* For trimming or scalping, use less
than full throttle to increase line life
and decrease head wear, especially:
During light duty cutting.
Near objects around which the line
can wrap such as small posts,
trees or fence wire.
* For mowing or sweeping, use full
throttle for a good clean job.
TRIMMING - Hold the bottom of the
trimmer head about 3 inches (8 cm)
above the ground and at an angle. Allow
only the tip of the line to make contact.
Do not force trimmer line into work
area.
Trimming
SCALPING - The scalping technique
removes unwanted vegetation down to
the ground. Hold the bottom of the
trimmer head about 3 inches (8 cm)
above the ground and at an angle. Al-
low the tip of the line to strike the
ground around trees, posts, monu-
ments, etc. This technique increases
line wear.
Scalping
MOWING - Your trimmer is ideal for
mowing in places conventional lawn
mowers cannot reach. In the mowing
position, keep the line parallel to the
ground. Avoid pressing the head into
the ground as this can scalp the
ground and damage the tool.
Mowing
SWEEPING - The fanning action of
the rotating line can be used to blow
away loose debris from an area. Keep
the line parallel to and above the area
surface and swing the tool from side to
side.
/._Sweeping
_'8 r
OPERATING INSTRUCTIONS FOR
USE OF BRUSHCUTTER ATTACH*
MENT WITH WEED BLADE
* Blade Thrust is a reaction that only
occurs when using a bladed unit. This
reaction can cause serious injury such
as amputation. Carefully study this
section. It is important that you under-
stand what causes blade thrust, how
you can reduce the chance of its oc-
curring, and how you can remain in
control of unit if blade thrust occurs.
* WHAT CAUSES BLADE THRUST -
Blade Thrust can occur when spin-
ning blade contacts an object that it
does not cut. This contact causes
blade to stop for an instant and then
suddenly move or "thrust" away from
object that was hit. The "thrusting" re-
action can be violent enough to cause
operator to be propelled in any direc-
tion and lose control of unit. The un-
controlled unit can cause serious injury
if blade contacts operator or others.
* WHEN BLADE THRUST OCCURS
- Blade Thrust can occur without
warning if the blade snags, stalls, or
binds. This is more likely to occur in
areas where it is difficult to see the
material being cut. By using the unit
properly, the occurrence of blade
thrust will be reduced and the opera-
tor will be less likely to lose control.
12
Cutonlygrass,weeds,andwoody
brushupto1/2inchindiameterwith
weedblade.Donotletbladecontact
materialitcannotcutsuchasstumps,
rocks,fences,metal,etc.,orclusters
ofhard,woodybrushwithadiameter
greaterthan1/2inch.
Useasharpblade.Adullbladeis
morelikelytosnagandthrust.
Cutonlyatfullthrottle.Thebladewill
havemaximumcuttingpowerandis
lesslikelytobindorstall.
"Feed"thebladedeliberatelyandnot
toorapidly.Thebladecanthrust
awayifitisfedtoorapidly.
Cutonlyfromyourlefttoyourright.
Cuttingonrightsideoftheshieldwill
throwdebris away from the operator.
Use the shoulder strap and keep a
firm grip on the unit with both hands.
A properly adjusted shoulder strap
will support the weight of the unit,
freeing your arms and hands to con-
trol and guide the cutting motion.
Keep feet comfortably spread apart
and braced for a possible sudden,
rapid thrust of unit. Do not overreach.
Keep firm footing and balance.
Keep blade below waist level. It will
be easier to maintain control of unit.
Do not raise the engine above your
waist as the blade can come danger-
ously close to your body.
Do not swing the unit with such force
that you are in danger of losing your
balance.
Bring the powerhead engine to cutting
speed before entering the material to
be cut.
If the blade does not turn when you
squeeze the throttle trigger of the pow-
erhead, make sure the attachment is
fully inserted into the coupler.
Always release the throttle trigger and
allow powerhead engine to return to
idle speed when not cutting. The blade
should not turn while the engine is run-
ning at idle. If the blade turns at idle,
do not use your unit. Refer to the CAR-
BURETOR ADJUSTMENT section of the
powerhead manual or contact your
Sears Service Center.
Maintain good firm footing while us-
ing the unit. Do this by planting feet
firmly in a comfortable apart position.
Cut while swinging the upper part of
your body from left to right.
As you move forward to the next
area to cut, be sure to maintain your
balance, and footing.
RECOMMENDED CUTTING POSITION
_2 o'clock
Cut using the 2 _}
o'clock to 4 o'clock
position of the 4 o'clock
blade
_l_ WARNING: The operator or oth-
ers must not try to clear away cut ma-
terial with the engine running or the
blade turning to avoid serious injury.
Stop engine and blade before remov-
ing materials wrapped around blade or
tube.
13
MAINTENANCE SCHEDULE
_WARNING: Always stop unit and disconnect spark plug wire before
performing maintenance.
CARE AND MAINTENANCE TASK WHEN TO PERFORM
Check for loose fasteners and parts
Check for damaged or worn parts
Inspect and clean unit and decals
Check or replace blade
Before each use
Before each use
After each use
Every 5 hours of operation
GENERAL RECOMMENDATIONS
The warranty on this attachment does
not cover items that have been sub-
jected to operator abuse or negli-
gence. To receive full value from the
warranty, the operator must maintain
the brushcutter attachment as instruct-
ed in this manual.
CHECK FOR DAMAGED OR
WORN PARTS
Contact Sears Service Center for re-
placement of damaged or worn parts.
Blade Shield - Discontinue use of
brushcutter attachment if shield is
damaged.
CHECK FOR LOOSE
FASTENERS AND PARTS
Blade nut
Fasteners
INSPECT AND CLEAN UNIT
AND DECALS
After each use, inspect complete unit
for loose or damaged parts. Clean
the unit and decals using a damp
cloth with a mild detergent.
Wipe off unit with a clean dry cloth.
BLADE MAINTENANCE
_WARNING: The blade will contin-
ue to spin after the engine stops or af-
ter the throttle trigger has been re-
leased. To avoid serious injury, make
sure the blade has stopped coasting
and disconnect the spark plug before
performing work on the blade.
WARNING: Always replace a
blade that is bent, warped, cracked,
broken, or damaged in any other way.
Never attempt to straighten and reuse
a damaged blade. Use only specified
replacement blade. Wear protective
gloves when handling or performing
maintenance on the blade to help
avoid injury.
Check blade for flatness periodically.
Lay the blade on a flat surface to in-
spect for flatness. Throw away a
blade that is not flat.
LINE REPLACEMENT
Always use Craftsman replacement
line.
Choose the line size best suited for the
job at hand. Red line is designed for
cutting grass and small weeds. The
black colored line is designed for cut-
ting larger weeds and light brush.
NOTE: Before inserting new line into
the holes in the cutting head, identify
the proper holes. Follow directions as
shown on the line glide plate.
1. Remove the old line and line glide
plate from the cutting head.
2. Clean entire surface of cutting
head.
3. Reinstall line glide plate (see il-
lustration). Align arrow with:
whenusing medium(red) or
(_) large (black) line
when using lines with diameter
(_) smaller than medium (red) line
(optional)
Line glide Arrow
Trimmer head
14
NOTE:Lineglideplatemustberein-
stalledincuttingheadbeforeinserting
newline.
4. Insertbothendsofyourline
throughtheproperholesinthe
sideofthecuttinghead.
!
5, Pull the line and make sure the
line is against the hub and ex-
tended full through the positioning
tunnels.
Line against
Tunnel \
6. Correctly installed line will be the
same length on both ends.
REPLACING THE CUTTING HEAD
1. Align hole in the dust cup with the
hole in the side of the gearbox by
rotating the dust cup.
2. Insert a small screwdriver into
aligned holes. This will keep the
shaft from turning while removing
and installing trimmer head.
3. While holding the screwdriver in
position, remove trimmer head by
turning clockwise.
4. Thread replacement trimmer head
onto the shaft by turning counterclock-
wise. Only tighten hand tight!
5. Remove the screwdriver.
BLADE REPLACEMENT
Refer to the ASSEMBLY section for
blade replacement instructions and il-
lustrations.
WARNING: Perform the following
steps after each use:
Allow attachment and gearbox to
cool before storing or transporting.
Store attachment with blade shield in
place. Position attachment so that
any sharp object cannot accidentally
cause injury.
Store the attachment in a dry, well
ventilated area out of the reach of
children.
SEASONAL STORAGE
Prepare attachment for storage at end
of season or if it will not be used for 30
days or more.
If your brushcutter attachment is to be
stored for a period of time:
Clean the entire attachment.
Inspect the blade shield area and
clean any dirt, grass, leaves, or de-
bris that has collected. Inspect the
blade and blade shield; replace a
blade that is bent, warped, cracked,
broken or damaged in any other way.
Lightly oil external metal surfaces.
Apply a coating of oil to the entire
surface of the blade; wrap it in heavy
paper or cloth.
Check entire attachment for loose
screws or nuts. Replace any dam-
aged, worn or broken parts.
At the beginning of the next season,
use only fresh fuel having the proper
gasoline to oil ratio.
15
Declaraci6n de Garantia 17 Mantenimiento 30
Identificaci6n de Simbolos 17 Servicio y Ajustes 31
Reglas de Seguridad 17 Almacenaje 32
Montaje 20 Lista de Piezas 16
Uso 26 Repuesto y Encargos Contratapa
GARANTIA COMPLETO DE UN A_IO PARA LA CORTADORA DE MALEZAS
ACCESORIO CRAFTSMAN ®
Durante un a_o completo, a partir de la fecha de compra, siempre que se haga el
mantenimiento, la lubricaci6n y los ajustes a esta Cortadora de Malezas Acceso*
rio Craftsman segQn las instrucciones de uso y mantenimiento en el manual,
Sears reparar_ cualquier defecto de materiales o de mano de obra gratuitamente.
Esta garantia excluye las partes que se gastan durante el uso normal.
Si se usa esta Cortadora de Malezas Accesorio Craftsman con fines comerciales,
esta garanfia tendr_ validez por s61a 90 dias a partir de la fecha de compra. Si se
usa esta Cortadora de Malezas Accesorio Craftsman con fines de alquiler, esta
garantia tendr_ validez s61amente por 30 ctias a partir de la fecha de compra.
Esta garanfia tendr_ validez Qnicamente mientras se use este producto dentro de
los Estados Unidos.
SE OBTENDRA SERVlCIO BAJO GARANTIA DEVOLVlENDO LA CORTADORA DE MAL-
EZAS ACCESORIO CRAFTSMAN AL TIENDA CE SEARS O CENTRO DE SERVlClO
SEARS MAS CERCANO EN LOS ESTADOS UNIDOS.
Esta garantia confiere derechos legales especificos al propietario, que tal vez
tenga asimismo otros derechos que varian entre estados.
Sears, Roebuck and Co., 13/817 WA Hoffman Estates, IL 60179
PELIGRO: iEsta cortadora Ir_--_ Lea y comprenda el
demalezas puede serpeligrosa! manual de instruc-
El uso descuidado o indebido de i_LJJ_ clones antes de user la
esta herramienta puede causar cortadora de malezas.
graves o a_n heridas fatales!
Use siempre la proteccion de oidos apropiada, la protecci6n de
ojos y la protecci6n de la cabeza.
ADVERTENCIA: AI usar cualqui*
er herramienta de fuerza de jardineria,
deber_n observarse precauciones b_si-
cas de seguirdad en todo momento
para reducir el riesgo de incendio y
graves heridas. Lea y cumpla con todas
]as instrucciones. Su incumplimiento
puede ocasionar lesiones graves.
PELIGRO: iEsta herramienta mo-
torizada puede set peligrosa! Puede
ocasionar lesiones graves, incluso la
amputaci6n o la ceguera, tanto al opera-
dor como a otras personas. Las adver-
tencias e instrucciones de seguridad
contenidas en este manual deben cum-
plirse en todo momento para garantizar
un nivel de seguridad y efectividad ra-
zonable durante la utilizaci6n del apara-
to. El operador es responsable del
cumplimiento de las advertencias e
instrucciones indicadas en este manual
y en el aparato. Antes de ensamblar y
utilizar el aparato, lea integramente el
17
manualdeinstrucciones.Limiteeluso
deesteaparatoapersonasqueprevia-
mentehayanleidoycomprendido,y
posteriormentecumplan,lasadverten-
ciaseinstruccionesindicadaseneste
manualyenelaparato.Nuncapermita
queesteaparatoseautilizadoporniSos.
MANUAL DE tNFORMACION DE
INSTRUCClONES SEGURIDAD DEL
APARATO
_1_PELIGRO: Nunca usedispositivos
desgranadores.
_1_PELIGRO: La cuchilla puede rebo-
tar violentamente en materiales que no
puede cortar, Los rebotes de la cuchilla
pueden causar la amputaci6n de brazos
o piernas. Mantenga a personas y anima-
]es lejos de la herramienta (15 metros).
,_ADVERTENCIA: La cuchilla/
]inea de corte puede despedir objetos
violentamente. Esto puede ocasionarle
ceguera o lesiones. Prot6jase los ojos
y las piernas.
UTILICE SIEM
Protecci6n
ocular
1 Perneras
Bo,as
ADVERTENClA: Zona de peligro
de objetos despedidos. La cuchina/linea
de corte puede despedir objetos violen-
tamente, Esto puede ocasionar ceguera
o lesiones a otros, Mantenga a perso-
nas y animales lejos de la herramienta
15 metros (50 pies).
_d Zona
e peligro
DADVERTENCIA: No utilice el ca-
bezal de corte como dispositivo de su-
jeci6n de la cuchilla,
4E_ADVERTENCIA: La cuchilla si-
gue girando incluso despu6s de soltar
el acelerador o de apagar el motor, In-
cluso cuando est_ girando libremente,
]a cuchilla puede despedir objetos o
causar cortes profundos si se toca ac-
cidentalmente, Detenga la cuchilla po-
niendo en contacto el lado izquierdo
de la misma con material ya cortado,
Para detener la cuchi- ._._
Ilacuando gire libre- _'_
mente, p6ngala en _J_'_
contacto con material
previamen_enmot_
SEGURIDAD DEL OPERADOR
Vistase apropiadamente. Siempre
use anteo os de seguridad o similar
protecc 6n para os o os cuando use
o d6 mantenimiento a este aparato
(anteojos de seguridad est_n dispo-
nibles). La protecci6n para los ojos
debe ser marcada con Z87.
Siempre utilize mascarilla para la
cara o mascarilla a prueba de polvo
si se va a trabajar en condiciones
donde hay polvo.
Siempre utilize pantalones pesados
y largos, mangas largas, botas y
guantes. Se recomienda el uso de
pantorrilleras de seguridad.
Siempre utilize protecci6n para los
pies. No trabaje descalzo ni en
sandalias. Evite la cuchilla/linea de
corte girante.
18
Mantengaelcabelloporencimade
loshombros,at_ndoloparatalefecto
siesnecesario.Nouseropasueltani
ropaconcorbatas,tiras,borlas,etc.
quecuelganlibremente.Puedenenre-
darseenlaspiezasenmovimiento.
Siest_completamenttapado,estar_
m_sprotegidodelosescombrosy
pedazosdeplantast6xicosarroja-
dosporlacuchillagirante.
Mant6ngasealerta.Nohagausodel
aparatoestandocansado,enfermo,
trastornadoobajolainfluenciadel
alcohol,dedrogasoderemedios.
VigilebienIoqueest_haciendo;use
delsentidocomen.
Useprotecci6ndeoidos.
Nuncapongaelaparatoenmarcha
niIodejeenmarchadentrodeun
recintocerrado.Respirarlosvapores
del combustible Io puede matar.
Mantenga las manijas libres de
aceite y de combustible.
Utilice siempre el mango y una
correa para hombro correctamente
ajustada al usar la cortadora de
malezas accesorio (yea MONTAJE).
MANTENIMIENTO Y SEGURIDAD
DEL APARATO
_l_ ADVERTENCIA: Desconecte la
bujia (o desconecte aparato de la cor-
riente el6ctrica) antes de hacer cualqu-
ier mantenimiento.
Antes de cada uso, busque las piezas
daSadas o sueltas y sustiteyalas. An-
tes de cada uso, busque posibles fu-
gas de combustible y, en su caso, re-
p_relas. Mantenga el aparato en buen
estado de funcionamiento.
Deseche la cuchillas dobladas, den-
tadas, partidas, rotas o deterioradas
de algen modo. Antes de utilizar la
unidad, sustituya las piezas del ca-
bezal de corte que est6n partidas,
rotas o deterioradas de alg_n modo.
Realice el mantenimiento del aparato
siguiendo los procedimientos reco-
mendados. Mantenga ]a cuchilla afila-
da. Nunca utilice dispositivos desgra-
nadores, cable, cuerda, alambre, etc.
Utilice exclusivamente la cuchilla o el
cabezal de corte especificado y ase-
ig6rese de que est6 correctamente
nstalado y firmemente sujeto.
Nunca ponga en marcha el motor
con el cubierta del embrague des-
montado. El embrague podria des-
prenderse y causar graves lesiones.
Aseg_rese de que el cuchilla o el
cabezal de corte se detiene al pasar
el motor al ralentL
Realice los ajustes del carburador
con la parte inferior apoyada en alto
para impedir que la cuchilla entren
en contacto con alg6n objeto. Sujete
el aparato con las manos, sin utilizar
la correa al hombro.
Cuando realice ajustes en el carbu-
rador, mantenga alejadas del lugar a
otras personas.
Utilice exclusivamente los accesorios
y recambios recomendados por
Craftsman.
Confie todas las tareas de manteni-
miento y reparaci6n no explicadas
en este manual a su Centro de
Servicio de Sears.
SEGURIDAD CON EL COMBUS*
TIBLE
Mezcle y vierta el combustible en
exteriores.
Mantenga el combustible alejado de
chispas y llamas.
Utilice recipientes homologados para
el uso de combustibles.
Impida que se fume cerca del com-
bustible o del aparato, tanto si 6ste se
encuentra parado o se est_ utilizando.
Antes de porter en marcha el motor,
limpie todo posible resto de combus-
tible derramado.
Antes de poner en marcha el motor,
al6jese como minimo 3 metros del lu-
gar de repostaje.
Antes de quitar el tap6n de combusti-
ble, detenga el motor y d6jelo enfriar.
Remueva la tapa del tanque de com-
bustible lentamente.
SEGURIDAD AL CORTAR
ADVERTENCIA: Antes de cada
uso, inspeccione la zona de trabajo.
Retire todos los objetos (rocas, cris-
tales rotos, clavos, cables, hilos, etc.)
que puedan ser despedidos o quedar
enredados en la cuchilla.
Mantenga alejados del lugar de tra-
bajo (15 metros) a otras personas,
ya sean niSos, acompaSantes o ayu-
dantes, y a animales. Detenga el
motor tan pronto como alguien se le
aproxime.
Mantenga siempre el motor junto al
lado derecho de su cuerpo.
Sujete firmemente la unidad con am-
bas manos.
Pise con seguridad y mantenga el
equilibrio en todo momento. No esti-
re el cuerpo en exceso.
Mantenga la cuchilla por debajo de
la cintura.
No levante el cabeza de motor por en-
cima de su cintura.
19
Mantenga todas las partes de su
cuerpo alejadas de la cuchilla y del
silendador.
Corte siempre de izquierda a derecha.
Si se corta con la linea del lado dere-
cho del protector, los escombros vo-
lar_n en sentido opuesto al usuario.
Use el aparato t]nicamente de dia o
en luz artifidal fuerte.
Utilice el aparato solamente para las
tareas explicadas en este manual.
TRANSPORTE Y ALMACENAMIENTO
Antes de proceder a su transporte,
detenga el cabeza de motor.
Mantenga el silenciador alejado del
cuerpo.
Antes de almacenar o transportar el
aparato en un vehfculo, deje enfnar
el motor y sujete bien el aparato.
Antes de guardar o transportar el
aparato, vacie el dep6sito de com-
bustible. Arranque el motor y d6jelo
en marcha hasta que se detenga
con el fin de agotar el combustible
que pueda quedar en el carburador.
Guarde el aparato y el combustible
en un lugar donde los vapores ema-
nados del combustible no puedan
entrar en contacto con chispas ni lla-
mas procedentes de calentadores
de agua. motores o interruptores
el6ctricos, hornos, etc.
CONTENIDO DE LA CAJA
Guarde el aparato de modo que la
cuchilla no puedan ocasionar lesio-
nes acddentalmente.
Guarde el aparato dentro, fuera del
alcance de los ni_os.
NOTA ESPECIAL: El estar expuesto
alas vibraciones a trav6s del uso pro-
Iongado de herramientas de fuerza a
gasolina puede cuasar daSos a los va-
sos sanguineos o a los nervios de los
dedos, las manos y las coyunturas en
aquellas personas que tienen propen-
sidad a los trastomos de la drculad6n
o alas hinchazones anormales. El uso
prolongado en tiempo fr{o ha sido aso-
dado con daSos a los vasos sna-
guineos de personas que por otra
parte se encuentran en perfecto esta-
do de salud. Si ocurren sintomas tales
como el entumecimiento, el dolor, la
falta de fuerza, los cambios en el color
o la textura de la piel o falta de sentido
en los dedos, las manos o las coyun-
turas, deje de usar esta m_quina in-
mediatamente y procure atend6n
m6dica. Los sistemas de anti-vibra-
d6n no garantizan que se eviten tales
problemes. Los usuarios que hacen
uso continuo y prolongando de las
herramientas de fuerza deben fiscali-
zar atentamente su estado fisico y el
estado del aparato.
GUARDE ESTAS INSTRUCClONES
Use la siguiente Iista para verificar que
todas la piezas hayan sido incluido:
Model 358.792441
Cortadora de Malezas Accesorio
Mango (con Abrazadara y Perilla)
Base de Abrazadera (con Tabulaciones
del Espaciador)
Correa al Hombro
Abrazadera Superior del Correa de
Hombro
Abrazadera Inferior del Correa de
Hombro (con Tabulaciones del Espa-
ciador)
Tornillos de Abrazadera del Mango (4)
Tornillos de Abrazadera del Correa de
Hombro (2)
Tuerca Larga para installar la Cuchilla
Arandela Abombada
Cabezal de Corte
Cuchilla con 4 puntas para el corte de
malezas (ensamblado en el aparato)
Tuerca Mariposa (atorninada en la pro-
tector)
Protector Met_lica (ensamblado en el
aparato)
Protector Pl_stica
Suspensor del Accesorio
Llave Hexagonal
Recipiente de linea
Aseg_irese de que ninguna pieza est6
daSada. No utilice piezas daSadas.
NOTA: Si necesita ayuda o detecta que
alguna pieza falta o est_ daSada, Ilame
al 1-800-235-5878.
MONTAJE
_I_i,ADVERTENClA: Si recibe el
aparato ya armado, repita todos los pa-
sos para asegurarse de que el aparato
est6 correctamente ensamblado y todas
las sujeciones firmes.
Un Ilave hexagonale (incluidas) se
requiere para el montaje.
2O
INSTALACIONDE LA ACCESORIO
DEL CORTADORA DE MALEZAS
PRECAUCION: AI instalar las acceso-
rio, ponga el aparato en una superfi-
cie plana para estabilidad.
1. Afloje el acoplador dando vuelta a
]a perilla a la izquierda.
Acoplador
AFLOJE
2,
3.
4.
5,
Perilla
Retire la tapa de tubo del acceso-
rio del cortadora de malezas (si
presente).
oloque el bot6n de conexi6n/des-
conexi6n del accesorio en el aguj-
ero de la guia del acoplador.
Empuje el accesorio en el acopla-
dor hasta que el bot6n de conex-
i6n/desconexi6n se encaje en el
primer agujero.
Antes de usar el aparato, apriete
]a perilla firmemente dando vuelta
a la derecha.
Primer
Acoplador\ PgLJe_ iAag_eriOade
Tubo Bot6n de Accesorio
Superior Conexi6n/ inferior
Desconexion
ADVERTENCIA: Antes de oper-
ar esta aparato, aseg0rese de que el
bot6n de conexi6n/desconexi6n est6
asegurado en el primer agujero y la
perilla est6 bien ajustada. Todos los
accesorios hart sido dise5ados para
ser utilizados en el primer agujero.
INSTALLATION DEL MANGO
PELIGRO: RIESGO DE CORTA-
DURA. Para evitar graves heridas, la
parte del mango en forma de barrera
debe ser instalada en el tubo superior
de la cabeza del motor/tubo superior
con el fin de mantener la distancia
entre el operador y la cuchilla durante
el giro de 6sta. ]nstale la abrazadera
del tubo sobre la flecha de la etiqueta
de seguridad del tubo superior (extre-
mo a la cabeza del motor de su apara-
to). Asegure que el mango este en
pos_clon con la abrazadera del mango
entre las flechas de la etiqueta del
mango.
AVISO: La base de la abrazadera del
tubo tiene cuatro (4) tabulaciones del
espaciador incluidas. Estas tabula-
clones se proporcionan para adaptar
esta accesorio para el uso con las ca-
bezas de motor/tubo superior que tie-
hen 1 pulgada del tubo superior de
di_metro (la abrazadera del tubo no
apretar_ abajo con seguridad en el
tubo superior de 1 pulgada de di_me-
tro sin usar estas tabulaciones del es-
paciador). Estas tabulaciones se de-
ben remover antes del uso y ponerlos
sobre los huecos del tornillo en la
base de ]a abrazadera. Estas tabula-
clones no son necesarias para las ca-
bezas de motor/tubo con un 7/8 de
pulgada en el tubo superior.
BASE DE ABRAZADERA
Tabulaciones
del Espaciador
Tabulaciones --..__
del Espaciador
colocadas para el
usoen el 1 pulga- _I
da de di_metro del
tubo superior
1,
2.
Coloque la abrazadera del tubo en
]a parte superior sobre la flecha en
]a etiqueta de seguridad.
Coloque ia base de ia abrazadera
debajo del tubo superior y alinee
los huecos del tornillo de la abra-
zadera con el tubo y la base de la
abrazadera (use las tabulaciones
del espaciador entre la abrazadera
del tubo y la base de la abrazadera
en caso de necesidad para asegu-
rar la abrazadera, es decir para 1
t_ul_ada de di_metro del tubo supe-
nor).
21
1 / 1

Craftsman Lawn Mower Accessory 358.792441 User manual

Category
Grass trimmers
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Ask the document