Craftsman 358792441 User manual

Brand: Craftsman

Model: 358792441

Category: Grass trimmers

Type: User manual

Instruction Manual

BRUSHCUTTER ATTACHMENT

Model No,

358.792441

NOT DESIGNED FOR USE

WITH ELECTRIC POWERHEADS

• Safety

• Assembly

• Operation

• Maintenance

• Parts List

• Espa_ol

DANGER:

Read and follow all Safety Rules and Operating

Instructions before first use of this product.

For answers to your questions about this product: Call 7

am-7 pm, Mon.-Sat., or 10 am-7 pm, Sun.

1-800-235-5878 <.o°,, listed are Central Time)

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

530164038 4/23/03

Warranty Statement 2 Service & Adjustments 14

Identification of Symbols 2 Storage 15

Safety Rules 2

Parts List 16

Assembly 5

Operation 10 Spanish 17

Maintenance 14 Parts and Ordering Back Cover

FULL ONE YEAR WARRANTY ON CRAFTSMAN® BRUSHCUTTER ATTACHMENT

For one year from the date of purchase, when this Craftsman Brushcutter Attach-

ment is maintained and lubricated according to the operating and maintenance

instructions in this manual, Sears will repair, free of charge, any defect in materi-

als or workmanship.

This warranty excludes expendable parts that become worn during normal use.

Ifthis Craftsman Brushcutter Attachment is used for commercial purposes, this war-

ranty applies for only 90 days from the date of purchase. If this Craftsman Brushcut-

ter Attachment is used for rental purposes, this warranty applies for only 30 days from

the date of purchase.

This warranty applies only while this product is in use in the United States.

WARRANTY SERVICE ISAVAILABLE BY RETURNING THE CRAFTSMAN BRUSHCUT-

TER ATTACHMENT TO THE NEAREST SEARS STORE OR SERVICE CENTER IN THE

UNITED STATES.

This warranty gives you specific legal rights, and you may also have other rights

which vary from state to state.

Sears, Roebuck and Co., I)/817 WA, Hoffman Estates, IL 60179

DANGER! This brushcutter

can be dangerous! Careless or

improper use can cause

serious or even fatal injury,

Read and understand the

instruction manual before

using the brushcutter.

[_ Always wear appropriate ear protection, eye protection and head protection.

DWARNING: When using garden-

ing appliances, basic safety precau-

tions should always be followed to re-

duce the risk of fire and serious injury.

Read and follow all instructions. Fail-

ure to do so can result in serious injury.

DANGER: This power tool can be

dangerous! This unit can cause seri-

ous injury including amputation or

blindness to the operator and others.

The warnings and safety instructions

in this manual must be followed to pro-

vide reasonable safety and efficiency

in using the unit. The operator is re-

sponsible for following the warnings

and instructions in this manual and on

the unit. Read the entire instruction

manual before assembling and using

the unit[ Restrict the use of this unit to

persons who read, understand, and

follow the warnings and instructions in

this manual and on the unit. Never al-

low children to operate this unit.

INSTRUCTION SAFETY INFORMATION

MANUAL ON THE UNIT

_l_ DANGER: Never use flailing de-

vices.

_l_ DANGER: Blade can thrust vio-

lently away from material it does not

cut. Blade thrust can cause amputa-

tion of arms or legs. Keep people and

animals 50 feet (15 meters) away.

_I_WARNING: Blade/trimmer line

can throw objects violently. You can be

blinded or injured. Wear eye and leg

protection.

ALWAYS WEAR:

_ Eye

Protection

mt Leg

• • Guards

I_ Boots

_I_WARNING: Hazard zone for

thrown objects. Blade/trimmer line can

throw objects violently. Others can be

blinded or injured. Keep people and

animals 50 feet (15 meters) away.

d Zone

all.WARNING: Do not use trimmer

head as a fastening device for the

blade.

_1_WARNING: The blade continues

to spin after throttle is released or en-

gine is turned off. The coasting blade

can throw objects or seriously cut you

if accidentally touched. Stop the blade

by contacting the left hand side of

coasting blade with material already

cut.

Stop coasting _ ___._

blade bycontact _.,.,,_r

with cut material.

OPERATOR SAFETY

° Dress properly. Always wear safety

glasses or similar eye protection

when operating, or performing main-

tenance on your unit (safety glasses

are available). Eye protection should

be marked Z87.

* Always wear face or dust mask if op-

eration is dusty.

* Always wear heavy, long pants, long

sleeves, boots, and gloves. Wearing

safety leg guards is recommended.

* Always wear foot protection. Do not

go barefoot or wear sandals. Stay

clear of spinning line/blade.

* Secure hair above shoulder length.

Secure or remove loose clothing and

jewelry or clothing with loosely hang-

ing ties, straps, tassels, etc. They

can be caught in moving parts.

* Being fully covered also helps pro-

tect you from debris and pieces of

toxic plants thrown by spinning line/

blade.

* Stay Alert. Do not operate unit when

you are tired, ill, upset or under influ-

ence of alcohol, drugs, or medica-

tion. Watch what you are doing; use

common sense.

* Wear hearing protection.

• Neverstartorruntheengineinsidea

closedroomorbuilding.Breathing

exhaustfumescankill.

• Keephandlesfreeofoilandfuel.

• Alwaysusethehandlebaranda

properly adjusted shoulder strap

when using brushcutter attachment

(see ASSEMBLY).

UNIT/MAINTENANCE SAFETY

_l_ WARNING: Disconnect power-

head spark plug (or disconnect power-

head from power source) before per-

forming maintenance.

• Look for and replace damaged or

loose parts before each use. Look

for and repair fuel leaks before use.

Keep unit in good working condition.

• Throw away blades that are bent,

warped, cracked, broken, or dam-

aged in any other way. Replace trim-

mer head parts that are cracked,

chipped, broken, or damaged in any

other way before using the unit.

• Maintain the unit according to recom-

mended procedures. Keep the blade

sharp. Never use flailing devices,

wire, rope, string, etc.

• Use only specified blade or trimmer

head; make sure it is properly in-

stalled and securely fastened.

• Never start engine with clutch shroud

removed. The clutch can fly off and

cause serious in ury.

• Be sure bade or tr mmer head stops

turning when engine idles.

• Make carburetor adjustments with the

lower end supported to prevent the

blade or trimmer line from contacting

any object. Hold the unit by hand; do

net use the shoulder strap for support.

• Keep others away when making car-

buretor adjustments.

• Use only recommended Craftsman

accessories and replacement parts.

• Have all maintenance and service

not explained in this manual per-

formed by a Sears Service Center.

FUEL SAFETY

• Mix and pour fuel outdoors.

• Keep away from sparks or flames.

• Use a container approved for fuel.

• Do not smoke or allow smoking near

fuel or the unit or while using the unit.

• Avoid spilling fuel or oil. Wipe up all

fuel spills before starting engine.

• Move at least 10 feet (3 meters) away

from fueling site before starting engine.

• Stop engine and allow it to cool be-

fore removing fuel cap,

• Remove fuel cap slowly,

CUTTING SAFETY

_II'I_,wARNING: Inspect the area to be

cut before each use. Remove objects

(rocks, broken glass, nails, wire, string,

etc.) which can be thrown or become

entangled in the blade or trimmer line.

• Keep others including children, ani-

mals, bystanders, and helpers at

least 50 feet (15 meters) away. Stop

the engine immediately if you are ap-

proached.

• Always keep engine on the right-

hand side of your body.

• Hold the unit firmly with both hands.

• Keep firm footing and balance. Do

not overreach.

• Keep blade/trimmer head below

waist level.

• Do net raise powerhead engine above

your waist.

• Keep all parts of your body away

from spinning blade/line and muffler.

• Cut from your left to your right. CUt-

ting on right side of shield will throw

debris away from the operator.

• Use only in daylight or good artificial

light.

• Use only for jobs explained in this

manual.

TRANSPORTING AND STORAGE

• Stop the powerhead engine before

carrying unit.

• Keep muffler away from your body.

• Allow engine to cool and secure unit

before storing or transporting it in a

vehicle.

• Empty the fuel tank before storing or

transporting the unit. Use up fuel left

in the carburetor by starting the en-

gine and letting it run until it stops.

• Store unit and fuel in an area where

fuel vapors cannot reach sparks or

open flames from water heaters,

electric motors or switches, furnaces,

etc.

• Store unit so the blade or line limiter

blade on shield cannot accidentally

cause in ury.

• Store un t ndoors, out of reach of

children.

SPECIALNOTICE:Exposuretovibra-

tionsthroughprolongeduseofgasoline

poweredhandtoolscouldcauseblood

vesselornervedamageinthefingers,

hands,andointsofpeoplepronetocir-

cuatondsordersorabnormaswerigs.

Prolongeduseincoldweatherhasbeen

linkedtobloodvesseldamageinother-

wisehealthypeople.Ifsymptomsoccur

suchas numbness, pain, loss of

strength, change in skin color or texture,

or loss of feeling in the fingers, hands, or

joints, discontinue the use of this tool

and seek medical attention. An anti-

vibration system does not guarantee the

avoidance of these problems. Users

who operate power tools on a continual

and regular basis must monitor closely

their physical condition and the condition

of this tool.

SAVE THESE INSTRUCTIONS

CARTON CONTENTS

Check carton contents against the fol-

lowing list.

Model 358.792441

• Brushcutter Attachment

• Handlebar (with Clamp and Knob)

• Handlebar Clamp Base (with Spacer

Tabs)

• Shoulder Strap

• Upper Shoulder Strap Clamp

• Lower Shoulder Strap Clamp (with

Spacer Tabs)

Handlebar Clamp Screws (4)

Shoulder Strap Clamp Screws (2)

Large nut for installing blade

Cupped washer

Trimmer head

4-point weed blade (assembled on

brushcutter attachment)

• Wing nut (screwed onto shield)

• Metal shield (assembled on brush-

cutter attachment)

• Plastic shield

• Attachment Hanger

• Hex Wrench

• Container of line

Examine parts for damage. Do not use

damaged parts.

NOTE: If you need assistance or find

that parts are missing or damaged, call

1-800-235-5878.

ASSEMBLY

=-&

all, WARNING: If received assembled,

repeat all steps to ensure your unit is

properly assembled and all fasteners

are secure.

• A hex wrench (provided) is required

for assembly.

INSTALLING BRUSHCUTTER AT-

TACHMENT

CAUTION: When removing or instal-

ling attachments, place the unit on a

flat surface for stability.

1. Loosen the coupler by turning the

knob counterclockwise.

Coupler

LOOSEN

TIGHTEN Knob

Remove the tube cap from the

brushcutter attachment (if present).

Position locking/release button of

attachment into guide recess of

coupler.

Push the attachment into the cou-

pler until the locking/release button

snaps into the primary hole.

Before using the unit, tighten the

knob securely by turning clock-

wise.

Coupler Primary Hole

\ /Guide Recess

Up!er L°ckin_g/[_

Tube Release Attachment

Button

all}WARNING: Make sure the lock-

ing/release button is locked in the pri-

mary hole and the knob is securely

tightened before operating the unit.

HANDLEBAR ASSEMBLY

DANGER: RISK OF CUT To

avoid serious injury, the barrier portion of

the handlebar must be installed as

shown on the upper tube of the power-

head to provide a barrier between op-

erator and the spinning blade. Attach

tube clamp above arrow on safety warn-

ing decal on the upper tube (powerhead

end of unit). Ensure handlebar is posi-

tioned on handlebar clamp between the

arrows on the handlebar decal.

NOTE:Thetubeclampbasehasfour

spacertabsattached.Thesetabsare

providedtoadaptthisattachmentfor

usewithpowerheadsthathavea1"di-

ameteruppertube(thetubeclampwill

nottightendownsecurelyonthe1"di-

ameteruppertubewithoutusingthese

spacertabs).Thetabsmustbebroken

offcompletelybeforeuseandplaced

overthescrewholesontheclampbase.

Thesetabsarenotneededforpower-

headswitha7/8"uppertube.

HANDLEBARCLAMPBASE

SpacerTabs

SpacerTabs_

o °ai i° e rer ae

upper tube _I

1. Place the tube clamp over the upper

tube above the arrow on the safety

decal.

2. Position the clamp base under the

upper tube and align the tube clamp

and clamp base screw holes (use

spacer tabs between tube clamp

and clamp base if necessary to se-

cure clamp, i.e. for 1" diameter up-

per tube).

Handlebar

POWERHEAD

END

Handlebar Clamp

between arrows on

handlebar decal

Clam

Knob

Clamp Screws

Arrow on

Safety Decal

ATTACHMENT END

3. Insert four screws into the screw

holes.

4. Secure tube clamp by tightening

screws with the hex wrench.

5. Position the handlebar as shown,

ensuring the handlebar is posi-

tioned on the handlebar clamp be-

tween the two arrows on the han-

dlebar decal.

6. Retighten handlebar byturning

clamp knob clockwise until handle-

bar is secure and stationary in

clamp (clamp knob cannot be

overtightened).

SHOULDER STRAP ASSEMBLY

_1_WARNING: Proper shoulder

strap and handlebar adjustments must

be made with the engine completely

stopped before using unit. The shoul-

der strap clamp must be installed as

shown above the handlebar on the up-

per tube (powerhead end of unit).

NOTE: The lower shoulder strap clamp

has two spacer tabs attached. These

tabs are provided to adapt this attach-

ment for use with powerheads that have

a 1" diameter upper tube (the shoulder

strap clamp will not tighten down se-

curely on the 1" diameter upper tube

without using these spacer tabs). The

tabs must be broken off completely be-

fore use and placed over the screw

holes on the lower shoulder strap clamp.

These tabs are not needed for power-

heads with a 7/8" upper tube.

LOWER SHOULDER STRAP

CLAMP

Spacer Tabs_'r _

.,dC_L.4--_ _- Spacer Tabs

I1_-_ positioned for use

on 1" diameter

upper tube

Place the upper shoulder strap

clamp over the upper tube above

the handlebar.

Position the lower shoulder strap

clamp under the upper tube and

align the upper and lower clamp

screw holes (use spacer tabs be-

tween upper and lower clamps if

necessary to secure clamp, i.e. for

1" diameter upper tube).

POWERHEAD

END

!Clamp

30 inches

I ATTACHMENT

Lower Shoulde •

END

Strap Clamp

3. Insert two screws into the screw

holes.

4. Secure shoulder strap clamp by

tightening screws with the hex

wrench.

5. Insert your right arm and head

through the shoulder strap and al-

low it to rest on your left shoulder.

Make sure the danger sign is on

your back and the hook is to the

right side of your waist.

NOTE: A one-half twist is built in the

shoulder strap to allow the strap to rest

flat on the shoulder.

6. Adjust the strap, allowing the book

to be about 6 inches below the

waist.

7. Fasten the strap hook to the clamp

and lift the tool to the operating

position.

8. Try on shoulder strap and adjust

for fit and balance before starting

the engine or beginning a cutting

operation.

NOTE: It may be necessary to relo-

cate the shoulder strap clamp on the

shaft for proper balancing of unit.

HARNESS

ADJUSTMENT

FOR BALANCE

6 inches

below

waist

4 - 12

inches

above

ground

CONFIGURING YOUR UNIT

You can configure your unit using a trim-

mer head for grass and light weeds, or a

weed blade for cutting grass, weeds,

and brush up to 1/2 inch in diameter. To

assemble your unit, go to the section for

the desired configuration and follow the

instructions.

ASSEMBLY INFORMATION -

TRIMMER HEAD

TRIMMER

HEAD

NOTE: Remove the blade and metal

shield before attaching the plastic shield

and trimmer head. To remove blade,

align hole in the dust cup with the hole

in the side of the gearbox by rotating

the blade. Insert a small screwdriver

into aligned holes. This will keep the

shaft from turning while loosening the

blade nut. Remove blade nut by turning

clockwise. Remove the screwdriver.

Remove both washers and blade. To

remove metal shield, loosen and re-

move the four mounting screws. See AT-

TACHINGTHE METALSHIELD and

INSTALLATIONOF THE METALBLADE for

illustrations. Be sure to store all parts

and instructions for future use.

INSTALLATION OF THE TRIMMER

HEAD

NOTE: Before installing the trimmer

head, make sure the dust cup and re-

taining washer are positioned on the

shaft of the gearbox, The retaining

washer must be positioned with the

raised section toward the gearbox,

1, Alignholeinthedustcupwiththe

holeinthesideofthegearboxby

rotatingthedustcup.

2, Insertasmallscrewdriverinto

alignedholes,Thiswillkeepthe

shaftfromturningwhiletightening

trimmerhead,

While holding the screwdriver in

position, thread trimmer head onto

the shaft by turning counterclock-

wise. Only tighten hand tightt

Gearbox

Dust Cup

Tnmmer Head _ Retaining

Washer

4, Removethe screwddver,

ATTACHING THE PLASTIC SHIELD

_WARNING: The shield must be

properly installed. The shield provides

partial protection from the risk of

thrown ob ects to the operator and oth-

ers and sequppedwtha ne mter

blade which cuts excess line to the

proper length. The line limiter blade

(on underside of shield) is sharp and

can cut you.

1. Remove wing nut from shield.

2. Insert bracket into slot on shield.

3. Pivot shield until bolt passes

through hole in bracket.

4. Tighten the wing nut securely.

Slot Bracket \ &:o_

Shield _*_ W_iingNut

_Gearbo_

ASSEMBLY INFORMATION - WEED

BLADE

_lb WEED

BLADE

NOTE: Remove the trimmer head and

plastic shield before attaching the metal

shield and installing the weed blade. To

remove the trimmer head, align hole in

the dust cup with the hole in the side of

the gearbox by rotating the dust cup.

Insert a small screwdriver into aligned

holes. This will keep the shaft from turn-

ing while loosening the trimmer head.

Remove the trimmer head by turning

clockwise. Remove the screwdriver. To

remove the plastic shield, loosen and

remove wing nut. Pivot shield to release

bracket from slot. See INSTALLATIONOF

THE TRIMMERHEADand ATTACHING

THE PLASTICSHIELD for illustrations. Be

sure to store all parts and instructions for

future use. Never use the trimmer head

with the metal blade installed.

ATTACHING THE METAL SHIELD

_I_WARNING: The metal shield

must be properly installed on the tool

anytime the tool is used with a blade.

The forward tip of the metal shield

helps to reduce the occurrence of

blade thrust which can cause serious

injury such as amputation to the opera-

tor or bystanders. Failure to install the

shield in the position shown can result

in serious injury to the operator. The

length of the shield must be aligned

with the length of the tube.

1. Place the metal shield under the

gearbox, and align the screw holes.

Gearbox

Shield

2, Insertandthreadthe4mounting

screwsthroughtheholesofthe

_earboxandthemetalshield.

ightenevenlyandsecurelywith

thehexwrenchprovided,

INSTALLATION OF THE METAL

BLADE

_l_ WARNING: Wear protective

gloves when handling or performing

maintenance on the blade to avoid in-

jury. The blade is sharp and can cut

you even when it is not moving.

_I_WARNING: Do not use any

blades, or fastening hardware other than

the washers and nuts shown in the fol-

lowing illustrations. These parts must be

provided by Sears and installed as

shown below. Failure to use proper parts

can cause the blade to fly off and seri-

ously hurt you or others.

NOTE: The dust cup and retaining

washer are located on the gearbox shaft

and not in the parts bag. All other fas-

teners mentioned in the following as-

sembly steps are in the parts bag.

1. Remove the retaining washer from

the threaded shaft of the gearbox.

Leave the dust cup on the shaft.

2. Install the blade and the retaining

washer over the threaded shaft.

3. Make sure the raised part of the re-

taining washer is facing the gearbox

and the raised area fits into the hole

in the center of the blade.

4. Slide the blade and retaining

washer onto the shaft of the gear-

box.

5. Place the cupped washer onto the

shaft. Make sure the cupped side

of the washer is toward the blade.

6. Install the blade nut by threading

onto the shaft counterclockwise.

Gearbox

Shield

Dust Cu Threaded Shaft

Blade

Retaining

Washer ---_

Cupped__

Washer

_",_-_ Nut

NOTE: Make sure all parts are in place

as illustrated, and the blade is sand-

wiched between the dust cup and the

retaining washer. There should be no

space between the blade and the dust

cup or the retaining washer.

7. Align hole in dust cup with hole in

side of gearbox by rotating the

blade.

8. Insert a small screwdriver into

aligned holes. This will keep the

shaft from turning while tightening

the blade nut.

9. Tighten blade nut firmly with a

wrench while holding screwdriver

in position.

10. Remove the screwdriver.

11. Turn blade by hand. If the blade

binds against the shield, or ap-

pears to be uneven, the blade is

not centered, and you must rein-

stall.

NOTE: To remove blade, insert screw-

driver into aligned holes. Unthread the

nut and remove parts. Be sure to store

parts and instructions for future use.

KNOW YOUR BRUSHCUTTER ATTACHMENT

READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR

BRUSHCUTTER ATTACHMENT. Compare the illustrations with your unit to familiarize

yourself with the location of various controls and adjustments, Save this manual for

future reference,

_T_ Hanger

Trimmer Shield

_'-_ Blade

Blade Shield

BLADE

The BLADE is designed for cutting

grass, weeds, and brush up to 1/2 inch

m diameter.

TRIMMER HEAD

The TRIMMER HEAD holds cutting line

and is designed for cutting grass and

light weeds.

BLADE SHIELD

The BLADE SHIELD provides protection

from the spinning blade.

TRIMMER SHIELD

The TRIMMER SHIELD provides protec-

tion from the spinning trimmer head.

OPERATING THE COUPLER

Your powerhead is equipped with a

coupler which enables optional attach-

ments to be installed. The optional at-

tachments are:

Edger ............... 358.792401

Cultivator ............ 358.792410

Blower .............. 358.792421

WARNING: Always disconnect

powerhead spark plug before remov-

ing or installing attachments.

REMOVING BRUSHCUTTER AT*

TACHMENT (OR OTHER OPTIONAL

ATTACHMENTS)

CAUTION: When removing or instal-

ling attachments, place the powerhead

and attachment on a flat surface for

stability.

1. Loosen the coupler by turning the

knob counterclockwise.

Upper Tube

Coupler

Lower \ LOOSEN

Attachment

TIGHTEN Knob

2. Press and hold the locking/release

button.

Lower Attachment

UpperTube

3. While securely holding the upper

tube, pull the attachment straight

out of the coupler.

INSTALLINGOPTIONAL ATTACH*

MENT

1. Remove the tube cap from the at-

tachment (if present)and discard.

2. Position locking/release button of

attachment into guide recess of

upper tube coupler.

Coupler Primary Hole

Upper Locking/ Attachment

Tube Release

Button

3. Push the attachment into the cou-

pler until the locking/release button

snaps into the primary hole.

4. Before using the unit, tighten the

knob securely by turning clock-

wise.

INSTALLING ATTACHMENT

HANGER

An attachment hanger is provided for

storage when attachment is not in use.

To install hanger on attachment:

1. Remove the tube cap from the at-

tachment (if present) and discard.

2. Press and hold the locking/release

button.

3. Push hanger onto the attachment

until the locking/release button

snaps into the hole.

OPERATING POSITION

ALWAYS WEAR:

Heavy,

Long Pants

Boots _,.

_ Protection

NOTE: This brushcutter attachment is

not designed for use with electric pow-

erheads.

When operating unit with brushcutter

attachment, clip shoulder strap onto

upper shoulder strap clamp, stand as

shown and check for the following:

• Wear eye protection and heavy

clothing.

• Keep arms extended with right hand

holding the trigger handle of power-

head.

• Keep left arm extended with left hand

holding the handlebar.

• Keep unit below waist level.

• Shoulder strap pad should be cen-

tered on your left shoulder and dan-

ger sign centered on your back.

• Maintain full weight of tool on left

shoulder.

• Without bending over, keep the blade

near and parallel to the ground and

not crowded into material being cut.

OPERATING INSTRUCTIONS FOR

USE OF BRUSHCUTTER ATTACH*

MENT WITH TRIMMER HEAD

_l_ WARNING: Always wear eye

protection. Never lean over the trim-

mer head. Rocks or debris can rico-

chet or be thrown into eyes and face

and cause blindness or other serious

injury.

Before trimming, bring engine to a

speed sufficient to cut material to be

trimmed.

De net run the engine at a higher speed

than necessary. The cutting line will cut

efficiently when the engine _srun at less

than full throttle. At lower speeds, there

is less engine noise and vibration. Al-

ways release the throttle trigger and

allow the engine to return to idle speed

when not cutting.

CUTTING METHODS

_I_WARNING: Use minimum speed

and do not crowd the line when cutting

around hard objects (rock, gravel,

fence posts, etc.), which can damage

the trimmer head, become entangled

in the line, or be thrown causing a seri-

ous hazard.

• The tip of the line does the cutting.

You will achieve the best perform-

ance and minimum line wear by not

crowding the line into the cutting

area. The right and wrong ways are

shown below.

Tip of line does the

Right

Line crowded into

i Wrong

*The line will easily remove grass and

weeds from around walls, fences,

trees and flower beds, but it also can

cut the tender bark of trees or shrubs

and scar fences.

* For trimming or scalping, use less

than full throttle to increase line life

and decrease head wear, especially:

• During light duty cutting.

• Near objects around which the line

can wrap such as small posts,

trees or fence wire.

* For mowing or sweeping, use full

throttle for a good clean job.

TRIMMING - Hold the bottom of the

trimmer head about 3 inches (8 cm)

above the ground and at an angle. Allow

only the tip of the line to make contact.

Do not force trimmer line into work

area.

Trimming

SCALPING - The scalping technique

removes unwanted vegetation down to

the ground. Hold the bottom of the

trimmer head about 3 inches (8 cm)

above the ground and at an angle. Al-

low the tip of the line to strike the

ground around trees, posts, monu-

ments, etc. This technique increases

line wear.

Scalping

MOWING - Your trimmer is ideal for

mowing in places conventional lawn

mowers cannot reach. In the mowing

position, keep the line parallel to the

ground. Avoid pressing the head into

the ground as this can scalp the

ground and damage the tool.

Mowing

SWEEPING - The fanning action of

the rotating line can be used to blow

away loose debris from an area. Keep

the line parallel to and above the area

surface and swing the tool from side to

side.

/._Sweeping

_'8 r

OPERATING INSTRUCTIONS FOR

USE OF BRUSHCUTTER ATTACH*

MENT WITH WEED BLADE

* Blade Thrust is a reaction that only

occurs when using a bladed unit. This

reaction can cause serious injury such

as amputation. Carefully study this

section. It is important that you under-

stand what causes blade thrust, how

you can reduce the chance of its oc-

curring, and how you can remain in

control of unit if blade thrust occurs.

* WHAT CAUSES BLADE THRUST -

Blade Thrust can occur when spin-

ning blade contacts an object that it

does not cut. This contact causes

blade to stop for an instant and then

suddenly move or "thrust" away from

object that was hit. The "thrusting" re-

action can be violent enough to cause

operator to be propelled in any direc-

tion and lose control of unit. The un-

controlled unit can cause serious injury

if blade contacts operator or others.

* WHEN BLADE THRUST OCCURS

- Blade Thrust can occur without

warning if the blade snags, stalls, or

binds. This is more likely to occur in

areas where it is difficult to see the

material being cut. By using the unit

properly, the occurrence of blade

thrust will be reduced and the opera-

tor will be less likely to lose control.

• Cutonlygrass,weeds,andwoody

brushupto1/2inchindiameterwith

weedblade.Donotletbladecontact

materialitcannotcutsuchasstumps,

rocks,fences,metal,etc.,orclusters

ofhard,woodybrushwithadiameter

greaterthan1/2inch.

• Useasharpblade.Adullbladeis

morelikelytosnagandthrust.

• Cutonlyatfullthrottle.Thebladewill

havemaximumcuttingpowerandis

lesslikelytobindorstall.

• "Feed"thebladedeliberatelyandnot

toorapidly.Thebladecanthrust

awayifitisfedtoorapidly.

• Cutonlyfromyourlefttoyourright.

Cuttingonrightsideoftheshieldwill

throwdebris away from the operator.

• Use the shoulder strap and keep a

firm grip on the unit with both hands.

A properly adjusted shoulder strap

will support the weight of the unit,

freeing your arms and hands to con-

trol and guide the cutting motion.

• Keep feet comfortably spread apart

and braced for a possible sudden,

rapid thrust of unit. Do not overreach.

Keep firm footing and balance.

• Keep blade below waist level. It will

be easier to maintain control of unit.

• Do not raise the engine above your

waist as the blade can come danger-

ously close to your body.

• Do not swing the unit with such force

that you are in danger of losing your

balance.

Bring the powerhead engine to cutting

speed before entering the material to

be cut.

If the blade does not turn when you

squeeze the throttle trigger of the pow-

erhead, make sure the attachment is

fully inserted into the coupler.

Always release the throttle trigger and

allow powerhead engine to return to

idle speed when not cutting. The blade

should not turn while the engine is run-

ning at idle. If the blade turns at idle,

do not use your unit. Refer to the CAR-

BURETOR ADJUSTMENT section of the

powerhead manual or contact your

Sears Service Center.

• Maintain good firm footing while us-

ing the unit. Do this by planting feet

firmly in a comfortable apart position.

• Cut while swinging the upper part of

your body from left to right.

• As you move forward to the next

area to cut, be sure to maintain your

balance, and footing.

RECOMMENDED CUTTING POSITION

_2 o'clock

Cut using the 2 _}

o'clock to 4 o'clock

position of the 4 o'clock

blade

_l_ WARNING: The operator or oth-

ers must not try to clear away cut ma-

terial with the engine running or the

blade turning to avoid serious injury.

Stop engine and blade before remov-

ing materials wrapped around blade or

tube.

MAINTENANCE SCHEDULE

_WARNING: Always stop unit and disconnect spark plug wire before

performing maintenance.

CARE AND MAINTENANCE TASK WHEN TO PERFORM

Check for loose fasteners and parts

Check for damaged or worn parts

Inspect and clean unit and decals

Check or replace blade

Before each use

After each use

Every 5 hours of operation

GENERAL RECOMMENDATIONS

The warranty on this attachment does

not cover items that have been sub-

jected to operator abuse or negli-

gence. To receive full value from the

warranty, the operator must maintain

the brushcutter attachment as instruct-

ed in this manual.

CHECK FOR DAMAGED OR

WORN PARTS

Contact Sears Service Center for re-

placement of damaged or worn parts.

• Blade Shield - Discontinue use of

brushcutter attachment if shield is

damaged.

• CHECK FOR LOOSE

FASTENERS AND PARTS

• Blade nut

• Fasteners

INSPECT AND CLEAN UNIT

AND DECALS

• After each use, inspect complete unit

for loose or damaged parts. Clean

the unit and decals using a damp

cloth with a mild detergent.

• Wipe off unit with a clean dry cloth.

BLADE MAINTENANCE

_WARNING: The blade will contin-

ue to spin after the engine stops or af-

ter the throttle trigger has been re-

leased. To avoid serious injury, make

sure the blade has stopped coasting

and disconnect the spark plug before

performing work on the blade.

WARNING: Always replace a

blade that is bent, warped, cracked,

broken, or damaged in any other way.

Never attempt to straighten and reuse

a damaged blade. Use only specified

replacement blade. Wear protective

gloves when handling or performing

maintenance on the blade to help

avoid injury.

• Check blade for flatness periodically.

Lay the blade on a flat surface to in-

spect for flatness. Throw away a

blade that is not flat.

LINE REPLACEMENT

• Always use Craftsman replacement

line.

Choose the line size best suited for the

job at hand. Red line is designed for

cutting grass and small weeds. The

black colored line is designed for cut-

ting larger weeds and light brush.

NOTE: Before inserting new line into

the holes in the cutting head, identify

the proper holes. Follow directions as

shown on the line glide plate.

1. Remove the old line and line glide

plate from the cutting head.

2. Clean entire surface of cutting

head.

3. Reinstall line glide plate (see il-

lustration). Align arrow with:

whenusing medium(red) or

(_) large (black) line

when using lines with diameter

(_) smaller than medium (red) line

(optional)

Line glide Arrow

Trimmer head

NOTE:Lineglideplatemustberein-

stalledincuttingheadbeforeinserting

newline.

4. Insertbothendsofyourline

throughtheproperholesinthe

sideofthecuttinghead.

5, Pull the line and make sure the

line is against the hub and ex-

tended full through the positioning

tunnels.

Line against

Tunnel \

6. Correctly installed line will be the

same length on both ends.

REPLACING THE CUTTING HEAD

1. Align hole in the dust cup with the

hole in the side of the gearbox by

rotating the dust cup.

2. Insert a small screwdriver into

aligned holes. This will keep the

shaft from turning while removing

and installing trimmer head.

3. While holding the screwdriver in

position, remove trimmer head by

turning clockwise.

4. Thread replacement trimmer head

onto the shaft by turning counterclock-

wise. Only tighten hand tight!

5. Remove the screwdriver.

BLADE REPLACEMENT

Refer to the ASSEMBLY section for

blade replacement instructions and il-

lustrations.

WARNING: Perform the following

steps after each use:

• Allow attachment and gearbox to

cool before storing or transporting.

• Store attachment with blade shield in

place. Position attachment so that

any sharp object cannot accidentally

cause injury.

• Store the attachment in a dry, well

ventilated area out of the reach of

children.

SEASONAL STORAGE

Prepare attachment for storage at end

of season or if it will not be used for 30

days or more.

If your brushcutter attachment is to be

stored for a period of time:

• Clean the entire attachment.

• Inspect the blade shield area and

clean any dirt, grass, leaves, or de-

bris that has collected. Inspect the

blade and blade shield; replace a

blade that is bent, warped, cracked,

broken or damaged in any other way.

• Lightly oil external metal surfaces.

• Apply a coating of oil to the entire

surface of the blade; wrap it in heavy

paper or cloth.

• Check entire attachment for loose

screws or nuts. Replace any dam-

aged, worn or broken parts.

• At the beginning of the next season,

use only fresh fuel having the proper

gasoline to oil ratio.

Declaraci6n de Garantia 17 Mantenimiento 30

Identificaci6n de Simbolos 17 Servicio y Ajustes 31

Reglas de Seguridad 17 Almacenaje 32

Montaje 20 Lista de Piezas 16

Uso 26 Repuesto y Encargos Contratapa

GARANTIA COMPLETO DE UN A_IO PARA LA CORTADORA DE MALEZAS

ACCESORIO CRAFTSMAN ®

Durante un a_o completo, a partir de la fecha de compra, siempre que se haga el

mantenimiento, la lubricaci6n y los ajustes a esta Cortadora de Malezas Acceso*

rio Craftsman segQn las instrucciones de uso y mantenimiento en el manual,

Sears reparar_ cualquier defecto de materiales o de mano de obra gratuitamente.

Esta garantia excluye las partes que se gastan durante el uso normal.

Si se usa esta Cortadora de Malezas Accesorio Craftsman con fines comerciales,

esta garanfia tendr_ validez por s61a 90 dias a partir de la fecha de compra. Si se

usa esta Cortadora de Malezas Accesorio Craftsman con fines de alquiler, esta

garantia tendr_ validez s61amente por 30 ctias a partir de la fecha de compra.

Esta garanfia tendr_ validez Qnicamente mientras se use este producto dentro de

los Estados Unidos.

SE OBTENDRA SERVlCIO BAJO GARANTIA DEVOLVlENDO LA CORTADORA DE MAL-

EZAS ACCESORIO CRAFTSMAN AL TIENDA CE SEARS O CENTRO DE SERVlClO

SEARS MAS CERCANO EN LOS ESTADOS UNIDOS.

Esta garantia confiere derechos legales especificos al propietario, que tal vez

tenga asimismo otros derechos que varian entre estados.

Sears, Roebuck and Co., 13/817 WA Hoffman Estates, IL 60179

PELIGRO: iEsta cortadora Ir_--_ Lea y comprenda el

demalezas puede serpeligrosa! manual de instruc-

El uso descuidado o indebido de i_LJJ_ clones antes de user la

esta herramienta puede causar cortadora de malezas.

graves o a_n heridas fatales!

Use siempre la proteccion de oidos apropiada, la protecci6n de

ojos y la protecci6n de la cabeza.

ADVERTENCIA: AI usar cualqui*

er herramienta de fuerza de jardineria,

deber_n observarse precauciones b_si-

cas de seguirdad en todo momento

para reducir el riesgo de incendio y

graves heridas. Lea y cumpla con todas

]as instrucciones. Su incumplimiento

puede ocasionar lesiones graves.

PELIGRO: iEsta herramienta mo-

torizada puede set peligrosa! Puede

ocasionar lesiones graves, incluso la

amputaci6n o la ceguera, tanto al opera-

dor como a otras personas. Las adver-

tencias e instrucciones de seguridad

contenidas en este manual deben cum-

plirse en todo momento para garantizar

un nivel de seguridad y efectividad ra-

zonable durante la utilizaci6n del apara-

to. El operador es responsable del

cumplimiento de las advertencias e

instrucciones indicadas en este manual

y en el aparato. Antes de ensamblar y

utilizar el aparato, lea integramente el

manualdeinstrucciones.Limiteeluso

deesteaparatoapersonasqueprevia-

mentehayanleidoycomprendido,y

posteriormentecumplan,lasadverten-

ciaseinstruccionesindicadaseneste

manualyenelaparato.Nuncapermita

queesteaparatoseautilizadoporniSos.

MANUAL DE tNFORMACION DE

INSTRUCClONES SEGURIDAD DEL

APARATO

_1_PELIGRO: Nunca usedispositivos

desgranadores.

_1_PELIGRO: La cuchilla puede rebo-

tar violentamente en materiales que no

puede cortar, Los rebotes de la cuchilla

pueden causar la amputaci6n de brazos

o piernas. Mantenga a personas y anima-

]es lejos de la herramienta (15 metros).

,_ADVERTENCIA: La cuchilla/

]inea de corte puede despedir objetos

violentamente. Esto puede ocasionarle

ceguera o lesiones. Prot6jase los ojos

y las piernas.

UTILICE SIEM

Protecci6n

ocular

1 Perneras

Bo,as

ADVERTENClA: Zona de peligro

de objetos despedidos. La cuchina/linea

de corte puede despedir objetos violen-

tamente, Esto puede ocasionar ceguera

o lesiones a otros, Mantenga a perso-

nas y animales lejos de la herramienta

15 metros (50 pies).

_d Zona

e peligro

DADVERTENCIA: No utilice el ca-

bezal de corte como dispositivo de su-

jeci6n de la cuchilla,

4E_ADVERTENCIA: La cuchilla si-

gue girando incluso despu6s de soltar

el acelerador o de apagar el motor, In-

cluso cuando est_ girando libremente,

]a cuchilla puede despedir objetos o

causar cortes profundos si se toca ac-

cidentalmente, Detenga la cuchilla po-

niendo en contacto el lado izquierdo

de la misma con material ya cortado,

Para detener la cuchi- • ._._

Ilacuando gire libre- _'_

mente, p6ngala en _J_'_

contacto con material

previamen_enmot_

SEGURIDAD DEL OPERADOR

• Vistase apropiadamente. Siempre

use anteo os de seguridad o similar

protecc 6n para os o os cuando use

o d6 mantenimiento a este aparato

(anteojos de seguridad est_n dispo-

nibles). La protecci6n para los ojos

debe ser marcada con Z87.

• Siempre utilize mascarilla para la

cara o mascarilla a prueba de polvo

si se va a trabajar en condiciones

donde hay polvo.

• Siempre utilize pantalones pesados

y largos, mangas largas, botas y

guantes. Se recomienda el uso de

pantorrilleras de seguridad.

• Siempre utilize protecci6n para los

pies. No trabaje descalzo ni en

sandalias. Evite la cuchilla/linea de

corte girante.

• Mantengaelcabelloporencimade

loshombros,at_ndoloparatalefecto

siesnecesario.Nouseropasueltani

ropaconcorbatas,tiras,borlas,etc.

quecuelganlibremente.Puedenenre-

darseenlaspiezasenmovimiento.

• Siest_completamenttapado,estar_

m_sprotegidodelosescombrosy

pedazosdeplantast6xicosarroja-

dosporlacuchillagirante.

• Mant6ngasealerta.Nohagausodel

aparatoestandocansado,enfermo,

trastornadoobajolainfluenciadel

alcohol,dedrogasoderemedios.

VigilebienIoqueest_haciendo;use

delsentidocomen.

• Useprotecci6ndeoidos.

• Nuncapongaelaparatoenmarcha

niIodejeenmarchadentrodeun

recintocerrado.Respirarlosvapores

del combustible Io puede matar.

• Mantenga las manijas libres de

aceite y de combustible.

• Utilice siempre el mango y una

correa para hombro correctamente

ajustada al usar la cortadora de

malezas accesorio (yea MONTAJE).

MANTENIMIENTO Y SEGURIDAD

DEL APARATO

_l_ ADVERTENCIA: Desconecte la

bujia (o desconecte aparato de la cor-

riente el6ctrica) antes de hacer cualqu-

ier mantenimiento.

• Antes de cada uso, busque las piezas

daSadas o sueltas y sustiteyalas. An-

tes de cada uso, busque posibles fu-

gas de combustible y, en su caso, re-

p_relas. Mantenga el aparato en buen

estado de funcionamiento.

• Deseche la cuchillas dobladas, den-

tadas, partidas, rotas o deterioradas

de algen modo. Antes de utilizar la

unidad, sustituya las piezas del ca-

bezal de corte que est6n partidas,

rotas o deterioradas de alg_n modo.

• Realice el mantenimiento del aparato

siguiendo los procedimientos reco-

mendados. Mantenga ]a cuchilla afila-

da. Nunca utilice dispositivos desgra-

nadores, cable, cuerda, alambre, etc.

• Utilice exclusivamente la cuchilla o el

cabezal de corte especificado y ase-

ig6rese de que est6 correctamente

nstalado y firmemente sujeto.

• Nunca ponga en marcha el motor

con el cubierta del embrague des-

montado. El embrague podria des-

prenderse y causar graves lesiones.

• Aseg_rese de que el cuchilla o el

cabezal de corte se detiene al pasar

el motor al ralentL

• Realice los ajustes del carburador

con la parte inferior apoyada en alto

para impedir que la cuchilla entren

en contacto con alg6n objeto. Sujete

el aparato con las manos, sin utilizar

la correa al hombro.

• Cuando realice ajustes en el carbu-

rador, mantenga alejadas del lugar a

otras personas.

• Utilice exclusivamente los accesorios

y recambios recomendados por

Craftsman.

• Confie todas las tareas de manteni-

miento y reparaci6n no explicadas

en este manual a su Centro de

Servicio de Sears.

SEGURIDAD CON EL COMBUS*

TIBLE

• Mezcle y vierta el combustible en

exteriores.

• Mantenga el combustible alejado de

chispas y llamas.

• Utilice recipientes homologados para

el uso de combustibles.

• Impida que se fume cerca del com-

bustible o del aparato, tanto si 6ste se

encuentra parado o se est_ utilizando.

• Antes de porter en marcha el motor,

limpie todo posible resto de combus-

tible derramado.

• Antes de poner en marcha el motor,

al6jese como minimo 3 metros del lu-

gar de repostaje.

• Antes de quitar el tap6n de combusti-

ble, detenga el motor y d6jelo enfriar.

• Remueva la tapa del tanque de com-

bustible lentamente.

SEGURIDAD AL CORTAR

ADVERTENCIA: Antes de cada

uso, inspeccione la zona de trabajo.

Retire todos los objetos (rocas, cris-

tales rotos, clavos, cables, hilos, etc.)

que puedan ser despedidos o quedar

enredados en la cuchilla.

• Mantenga alejados del lugar de tra-

bajo (15 metros) a otras personas,

ya sean niSos, acompaSantes o ayu-

dantes, y a animales. Detenga el

motor tan pronto como alguien se le

aproxime.

• Mantenga siempre el motor junto al

lado derecho de su cuerpo.

• Sujete firmemente la unidad con am-

bas manos.

• Pise con seguridad y mantenga el

equilibrio en todo momento. No esti-

re el cuerpo en exceso.

• Mantenga la cuchilla por debajo de

la cintura.

• No levante el cabeza de motor por en-

cima de su cintura.

• Mantenga todas las partes de su

cuerpo alejadas de la cuchilla y del

silendador.

• Corte siempre de izquierda a derecha.

Si se corta con la linea del lado dere-

cho del protector, los escombros vo-

lar_n en sentido opuesto al usuario.

• Use el aparato t]nicamente de dia o

en luz artifidal fuerte.

• Utilice el aparato solamente para las

tareas explicadas en este manual.

TRANSPORTE Y ALMACENAMIENTO

• Antes de proceder a su transporte,

detenga el cabeza de motor.

• Mantenga el silenciador alejado del

cuerpo.

• Antes de almacenar o transportar el

aparato en un vehfculo, deje enfnar

el motor y sujete bien el aparato.

• Antes de guardar o transportar el

aparato, vacie el dep6sito de com-

bustible. Arranque el motor y d6jelo

en marcha hasta que se detenga

con el fin de agotar el combustible

que pueda quedar en el carburador.

• Guarde el aparato y el combustible

en un lugar donde los vapores ema-

nados del combustible no puedan

entrar en contacto con chispas ni lla-

mas procedentes de calentadores

de agua. motores o interruptores

el6ctricos, hornos, etc.

CONTENIDO DE LA CAJA

• Guarde el aparato de modo que la

cuchilla no puedan ocasionar lesio-

nes acddentalmente.

• Guarde el aparato dentro, fuera del

alcance de los ni_os.

NOTA ESPECIAL: El estar expuesto

alas vibraciones a trav6s del uso pro-

Iongado de herramientas de fuerza a

gasolina puede cuasar daSos a los va-

sos sanguineos o a los nervios de los

dedos, las manos y las coyunturas en

aquellas personas que tienen propen-

sidad a los trastomos de la drculad6n

o alas hinchazones anormales. El uso

prolongado en tiempo fr{o ha sido aso-

dado con daSos a los vasos sna-

guineos de personas que por otra

parte se encuentran en perfecto esta-

do de salud. Si ocurren sintomas tales

como el entumecimiento, el dolor, la

falta de fuerza, los cambios en el color

o la textura de la piel o falta de sentido

en los dedos, las manos o las coyun-

turas, deje de usar esta m_quina in-

mediatamente y procure atend6n

m6dica. Los sistemas de anti-vibra-

d6n no garantizan que se eviten tales

problemes. Los usuarios que hacen

uso continuo y prolongando de las

herramientas de fuerza deben fiscali-

zar atentamente su estado fisico y el

estado del aparato.

GUARDE ESTAS INSTRUCClONES

Use la siguiente Iista para verificar que

todas la piezas hayan sido incluido:

Model 358.792441

• Cortadora de Malezas Accesorio

• Mango (con Abrazadara y Perilla)

• Base de Abrazadera (con Tabulaciones

del Espaciador)

• Correa al Hombro

• Abrazadera Superior del Correa de

Hombro

• Abrazadera Inferior del Correa de

Hombro (con Tabulaciones del Espa-

ciador)

• Tornillos de Abrazadera del Mango (4)

• Tornillos de Abrazadera del Correa de

Hombro (2)

• Tuerca Larga para installar la Cuchilla

• Arandela Abombada

• Cabezal de Corte

• Cuchilla con 4 puntas para el corte de

malezas (ensamblado en el aparato)

• Tuerca Mariposa (atorninada en la pro-

tector)

• Protector Met_lica (ensamblado en el

aparato)

• Protector Pl_stica

• Suspensor del Accesorio

• Llave Hexagonal

• Recipiente de linea

Aseg_irese de que ninguna pieza est6

daSada. No utilice piezas daSadas.

NOTA: Si necesita ayuda o detecta que

alguna pieza falta o est_ daSada, Ilame

al 1-800-235-5878.

MONTAJE

_I_i,ADVERTENClA: Si recibe el

aparato ya armado, repita todos los pa-

sos para asegurarse de que el aparato

est6 correctamente ensamblado y todas

las sujeciones firmes.

• Un Ilave hexagonale (incluidas) se

requiere para el montaje.

INSTALACIONDE LA ACCESORIO

DEL CORTADORA DE MALEZAS

PRECAUCION: AI instalar las acceso-

rio, ponga el aparato en una superfi-

cie plana para estabilidad.

1. Afloje el acoplador dando vuelta a

]a perilla a la izquierda.

Acoplador

AFLOJE

Perilla

Retire la tapa de tubo del acceso-

rio del cortadora de malezas (si

presente).

oloque el bot6n de conexi6n/des-

conexi6n del accesorio en el aguj-

ero de la guia del acoplador.

Empuje el accesorio en el acopla-

dor hasta que el bot6n de conex-

i6n/desconexi6n se encaje en el

primer agujero.

Antes de usar el aparato, apriete

]a perilla firmemente dando vuelta

a la derecha.

Primer

Acoplador\ PgLJe_ iAag_eriOade

Tubo Bot6n de Accesorio

Superior Conexi6n/ inferior

Desconexion

ADVERTENCIA: Antes de oper-

ar esta aparato, aseg0rese de que el

bot6n de conexi6n/desconexi6n est6

asegurado en el primer agujero y la

perilla est6 bien ajustada. Todos los

accesorios hart sido dise5ados para

ser utilizados en el primer agujero.

INSTALLATION DEL MANGO

PELIGRO: RIESGO DE CORTA-

DURA. Para evitar graves heridas, la

parte del mango en forma de barrera

debe ser instalada en el tubo superior

de la cabeza del motor/tubo superior

con el fin de mantener la distancia

entre el operador y la cuchilla durante

el giro de 6sta. ]nstale la abrazadera

del tubo sobre la flecha de la etiqueta

de seguridad del tubo superior (extre-

mo a la cabeza del motor de su apara-

to). Asegure que el mango este en

pos_clon con la abrazadera del mango

entre las flechas de la etiqueta del

mango.

AVISO: La base de la abrazadera del

tubo tiene cuatro (4) tabulaciones del

espaciador incluidas. Estas tabula-

clones se proporcionan para adaptar

esta accesorio para el uso con las ca-

bezas de motor/tubo superior que tie-

hen 1 pulgada del tubo superior de

di_metro (la abrazadera del tubo no

apretar_ abajo con seguridad en el

tubo superior de 1 pulgada de di_me-

tro sin usar estas tabulaciones del es-

paciador). Estas tabulaciones se de-

ben remover antes del uso y ponerlos

sobre los huecos del tornillo en la

base de ]a abrazadera. Estas tabula-

clones no son necesarias para las ca-

bezas de motor/tubo con un 7/8 de

pulgada en el tubo superior.

BASE DE ABRAZADERA

Tabulaciones

del Espaciador

Tabulaciones --..__

del Espaciador

colocadas para el

usoen el 1 pulga- _I

da de di_metro del

tubo superior

Coloque la abrazadera del tubo en

]a parte superior sobre la flecha en

]a etiqueta de seguridad.

Coloque ia base de ia abrazadera

debajo del tubo superior y alinee

los huecos del tornillo de la abra-

zadera con el tubo y la base de la

abrazadera (use las tabulaciones

del espaciador entre la abrazadera

del tubo y la base de la abrazadera

en caso de necesidad para asegu-

rar la abrazadera, es decir para 1

t_ul_ada de di_metro del tubo supe-

nor).

Page is loading ...

Craftsman 358792441 User manual

Brand: Craftsman

Model: 358792441

Category: Grass trimmers

Type: User manual

Download PDF

report

in other languages

español: Craftsman 358792441 Manual de usuario

Craftsman 358792441 User manual

Craftsman 358792441 User manual

in other languages

Related papers

Other documents