Marantec Control x.51 Owner's manual

Control x.51

Control unit for Hinged Gates

GB

Manual for installation and operation

2 Manual for installation and operation, Control x.51 GB (#102668)
2. Table of contents
1. Meaning of symbols  . . . . . . . . . . . . . . . . . . .2
2. Table of contents . . . . . . . . . . . . . . . . . . . . . .2
3. General safety advice  . . . . . . . . . . . . . . . . . .3
4. Product overview  . . . . . . . . . . . . . . . . . . . . .4
4.1 Control x.51 supply package  . . . . . . . . .4
4.2 Gate system . . . . . . . . . . . . . . . . . . . . . .5
5. Preparation for mounting  . . . . . . . . . . . . . .5
5.1 General notes  . . . . . . . . . . . . . . . . . . . .5
5.2  Checks . . . . . . . . . . . . . . . . . . . . . . . . . .6
6. Installation  . . . . . . . . . . . . . . . . . . . . . . . . . . .6
6.1 Fixing the control unit  . . . . . . . . . . . . . .6
6.2 Connection of control elements   . . . . . .7
6.3 Connecting the motor unit to 
the controls  . . . . . . . . . . . . . . . . . . . . .13
6.4 Connection of the mains cable   . . . . . .15
7. Hand transmitter . . . . . . . . . . . . . . . . . . . . .15
7.1 Operation and accessories  . . . . . . . . . .15
7.2 Hand transmitter coding   . . . . . . . . . . .16
8. Initial operation . . . . . . . . . . . . . . . . . . . . . .18
8.1 Connecting the modular antenna  . . . .18
8.2 Overview of the control unit  . . . . . . . .18
8.3 Overview of the display functions  . . . .19
8.4 Reference point  . . . . . . . . . . . . . . . . . .19
8.5 Express programming . . . . . . . . . . . . . .20
8.6 Function test  . . . . . . . . . . . . . . . . . . . .23
9. Extended operator functions  . . . . . . . . . . .24
9.1 General notes on extended operator
functions  . . . . . . . . . . . . . . . . . . . . . . .24
9.2 Programming structure for extended
 operator functions (Example for Level 2,
Menu 2) . . . . . . . . . . . . . . . . . . . . . . . .25
9.3 General overview of the programmable
functions   . . . . . . . . . . . . . . . . . . . . . .26
9.4 Functions overview for the levels  . . . . .28
10. Messages  . . . . . . . . . . . . . . . . . . . . . . . . . . .38
10.1 Status messages   . . . . . . . . . . . . . . . . .38
10.2  Fault messages . . . . . . . . . . . . . . . . . . .38
10.3 Rectifying faults  . . . . . . . . . . . . . . . . . .40
11. Attachment  . . . . . . . . . . . . . . . . . . . . . . . . .43
11.1 Connection diagram Control x.51  . . . .43
11.3 Declaration of incorporation  . . . . . . . .44
11.2 Technical Data for Control x.51  . . . . . .44
11.4 EC Declaration of Conformity  . . . . . . .45
1. Meaning of symbols
Caution! 
Danger of personal injury!
The following safety advice must 
be observed at all times so as to avoid
personal injury!
Attention! 
Danger of material damage!
The following safety advice must 
be observed at all times so as to avoid
material damage!
Advice / Tip
Check
Reference
i
Advice
Type plate on control unit
Type: ________________________________________________
Art. No.: _____________________________________________
Product No.: __________________________________________

Manual for installation and operation, Control x.51 GB (#102668) 3

Please read carefully!

Target group

This operator system may only be installed, connected and put into

operation by qualified and trained professionals!

Qualified and trained specialist personnel are persons

- who have knowledge of the general and special safety regulations,

- who have knowledge of the relevant electro-technical regulations,

- with training in the use and maintenance of suitable safety equipment,

- who are sufficiently trained and supervised by qualified electricians,

- who are able to recognise the particular hazards involved when

working with electricity,

- with knowledge regarding applications of the EN 12635 standard

(installation and usage requirements).

Warranty

For an operations and safety warranty, the advice in this instruction

manual has to be observed. Disregarding these warnings may lead

to personal injury or material damage. If this advice is disregarded,

the manufacturer will not be liable for damages that might occur.

Batteries, fuses and bulbs are excluded from warranty.

To avoid installation errors and damage to the gate and operator

system, it is imperative that the installation instructions are followed.

The system may only be used after thoroughly reading the respective

mounting and installation instructions.

The installation and operating instructions are to be given to the gate

system user, who must keep them safe. They contain important advice

for operation, checks and maintenance.

This item is produced according to the directives and standards

mentioned in the Manufacturer's Declaration and in the Declaration

of Conformity. The product has left the factory in perfect condition

with regard to safety.

Power-operated windows, doors and gates must be checked by an

expert (and this must be documented) before they are put into

operation and thereafter as required, but at least once a year.

Correct use

- The control unit is exclusively designed for the control of hinged

gates.

- The control unit requires a suitable motor unit for operation.

- The gate must never be used to move persons or objects.

Beside the advice in these instructions, please observe the

general safety and accident prevention regulations!

Our sales and supply terms and conditions are effective.

Information on installing the control unit

• Before commencing cabling works it is very important to disconnect

the operator system from the electricity supply.

Ensure that the electricity supply remains disconnected throughout

the cabling works.

• Adhere to the local protection regulations.

• Lay the electricity supply cables and control cables; these MUST be

laid separately. The controls voltage is 24 V DC.

• Install all the impulse transmitters and control devices (e.g. remote

control buttons) within sight of the gate and at a safe distance

from the moving parts of the gate. A minimum installation height

of 1.5 m must be observed.

• Ensure that no part of the gate extends across public footways or

roads when the installation is complete.

Information on commissioning the operator system

After initial operation, the persons responsible for operating the gate

system, or their representatives must be familiarised with the use of

the system.

• Make sure that children cannot access the gate control unit.

• Before moving the gate, make sure that there are neither persons

nor objects in the operating range of the gate.

• Test all existing emergency command devices.

• Never insert your hands into a running gate or moving parts.

• Pay attention to any parts of the gate system that could cause

crushing or shearing damage or accidents.

The EN 13241-1 regulations must be observed.

Information on servicing the operator system

To ensure proper operation, the following items must be checked

regularly and repaired if necessary.

Before any works to the gate system are undertaken, the operator

system must be disconnected from the mains.

• Check once a month that the operator system stops and reverses

in every position when the gate touches an obstacle. Place an

obstacle in the path of the gate to check this.

• Check the settings of the OPEN and CLOSE automatic cut-out

function.

• Check all movable parts of the gate and operator system.

• Check the gate system for signs of wear or damage.

• Check whether the gate can be easily moved by hand.

Information on cleaning the operator system

Never use water jets, high pressure cleaners, acids or bases for

cleaning.

3. General safety advice

4 Manual for installation and operation, Control x.51 GB (#102668)

1 Control x.51

2 Handle

3 Screws 3.5 x 32 (4x)

4 Wall plugs S6 (4x)

5 Spacer elements (2x)

6 Screw fixing insert with 2 flat cable openings

7 M20 screw fixing with flat cable insert

8 M20 screw fixing with round cable insert

9 M16 screw fixing with round cable insert

Control unit

Mounting kit for control unit

10 Hand transmitter

11 Sun visor clip

12 Module antenna

13 Transmission plug

Remote control

4.1 Control x.51 supply package

4. Product overview

7

9

6

3

4

4.1 / 1

4.1 / 2

1

8

2

4.1 / 3

!¯

!Ø

!”

!#

5

Manual for installation and operation, Control x.51 GB (#102668) 5

4. Product overview

Reference:

The design of the gate system is

described in the documentation of the

motor unit.

i

5. Preparation for mounting

5.1 General notes

The pictures in these instructions are not true-to-scale.

Dimensions are always given in millimetres (mm)!

The motor unit and the controls must be mounted on

the inside of the gate system.

4.2 Gate system

Attention!

In order to guarantee correct

mounting, carry out the following

checks before installing.

Supply package

• Check the package to ensure that all the parts are

included.

• Check that you have all the additional components

that are necessary for your particular installation

requirements.

Gate system

• Ensure that your gate system has an appropriate

electricity supply connection and a facility

for disconnecting the mains. The minimum

cross-sectional area of the earth cable is

3 x 1.5 mm

2

.

• Ensure that all cables are suitable for outdoor use

(UV resistant and cold resistant).

• Make sure that a suitable motor unit is available.

5. Preparation for mounting

6 Manual for installation and operation, Control x.51 GB (#102668)

6.1 / 1

• Open the control unit.

• Mount the control unit using the spacer elements (A).

3.5 x 32

Attention!

The control unit must be installed in

such a way that the motor cable can be

fed through the screw fixing at the

base of the control unit.

6.1 / 2

A

6.1 Fixing the control unit5.2 Checks

6. Installation

Manual for installation and operation, Control x.51 GB (#102668) 7

6.2 Connection of control elements

Attention!

In order to avoid damaging the

controls:

- The local safety regulations must be

complied with at all times.

- It is very important that mains cables

are laid separately from control cables.

- The controls voltage must be 24 V DC.

- If external voltages are applied at

terminals XM70A, XV51A, XM70B,

XV51B, XB99, XP54B, XP54A, XP62B,

XP62A or XB70, the entire electronic

system will be destroyed.

- Only potential-free contacts may be

connected to terminals B9, 5, 34, 3

and 8 (XB99).

Caution!

Danger of electric shock:

Before any cabling works begin, it must

be ensured that the cables are

disconnected from the power supply.

During cabling works, it must be

ensured that the cables remain

disconnected from the power supply at

all times (e.g. prevent reconnection).

P

1

2

3

4

5

6

7

8

1

2

L

N

PE

15

16 17

6.2 / 1

XN81

XV51B

XM70B

XM70A

XV51A

XB99

XP54A

XB70

XP54B

XH01

XP62A

XP62B

XN70

Label Type / function

i

XB70 Connection of modular antenna 8.1

XB99

Connection of external control

elements

6.2 / 2

6.2 / 3

6.2 / 4

6.2 / 5

XH01

Connection for programmable

output 16/17 (e.g. signal light,

24 V DC, 0,5 A)

Wiping impulse 15/16

6.2 / 6

6.2 / 7

XM70A

Connection for motor unit

(MASTER)

6.3 / 5

6.3 / 8

XM70B

Connection for motor unit

(SLAVE)

6.3 / 5

6.3 / 8

XN70

Connection Battery Backup

(if available)

-

XN81 Connection for mains cable

6.2 / 6

6.4

XP54A

Connection for closing edge

safety device, gate travelling

direction CLOSE

6.2 / 8

XP54B

Connection for closing edge

safety device, gate travelling

direction OPEN

6.2 / 8

XP62A

Connection for photocell,

gate travelling direction CLOSE

6.2 / 9

XP62B

Connection for photocell,

gate travelling direction OPEN

6.2 / 9

XV51A

Connection for rpm detector

and reference point sensor

(MASTER)

6.3 / 5

6.3 / 8

XV51B

Connection for rpm detector

and reference point sensor

(SLAVE)

6.3 / 5

6.3 / 8

8 Manual for installation and operation, Control x.51 GB (#102668)

Reference:

When installing external control

elements, or safety and signal

equipment, the relevant instructions

must be observed.

i

Terminal XB99

Factory settings:

B9 and 5 bridged

Connection option 1:

-XB99

B9 5 34 3 8

-SB5

12 11

-SB8

14 13

-XB99

B9 5 34 3 8

6.2 / 2

6.2 / 3

M06E039

6. Installation

Connection option 2:

Reference:

The connection configuration depends

on the programming of the special

functions. Depending on the program-

ming, impulse or direction buttons can

be connected.

Programming the special functions is

described in Section 9.4 (Level 5).

i

-SB5

12 11

-SB3

14 13

-SB3 4

12 11

-SB8

14 13

-XB99

B9 5 34 3 8

6.2 / 4

Label Type / function

3 Connection for intermediate position

5 Stop connection

8 Impulse connection

34 Connection for closing prevention device

B9 +24 V DC connection

SB3 Button for intermediate position

SB5 STOP button

SB8 Impulse button

SB34

Button for closing prevention device /

Drive system stops and reverses

M06E039

Manual for installation and operation, Control x.51 GB (#102668) 9

6. Installation

Advice:

If a closing prevention device

(photocell, timer, …) is connected to

XB99, the controls will recognise it

automatically after “Mains On”

(contact SB34 must be closed).

The photocell can be deactivated later

(Level 8 / Menu 1).

When the contacts of a closing

prevention device are open, the gate

can no longer be closed.

Additional external control elements,

and safety and signal devices with 24 V

connections must be connected to

XB99/B9 and XH01/16.

Connection option 3:

- External radio receiver

- XB99

B9 5

34

3 8

- XH01

15 16 17

- X1

+

-

- S1

14 13

1 2

6.2 / 5

M07E027

Label Type / function

XB99 Connection of external control elements

3 Connection for intermediate position

5 Stop connection

8 Impulse connection

34 Connection for closing prevention device

B9 24 V DC connection

X1 Connection for external receiver

1

Connection of potential-free normally open

contact

2

Connection of potential-free normally open

contact

+ 24 V DC connection

- GND connection

S1

Normally open contact, receiver,

potential-free

XH01 Connection of control unit output

15 Connection for electric lock, 24 V DC

16 GND connection

17 Connection for programmable output

10 Manual for installation and operation, Control x.51 GB (#102668)

Terminals XN81 / XH01

- XN81

- X0

L

PE

N

L

PE

- F0

L

N

PE

6.2 / 6

16

15

17

- YH15

- HH17

- XH01

M07E039

M07E038

Label Type / function

L Connection for phase

N Connection for neutral wire

PE Earth wire connection

15 / 16 Connection for electric lock, 24 V DC

16 GND connection

16 / 17

Connection of programmable output

(24 V DC / 0.5 A)

HH14 Signal light

HH17 Signal light 24 V

KH17 User’s relay 24 V

YH15 Electric lock (provided by the customer)

6. Installation

Connection option:

- Connection for signal light with external relay

- XH01

16

15

17

1411

12

A2 A1

- KH17

- HH14

L

N

6.2 / 7

M07E038

Manual for installation and operation, Control x.51 GB (#102668) 11

6. Installation

Terminals XP54A / XP54B

Label Type / function

P5 GND connection

46

Connection for signal of closing edge safety

device

Gate travelling direction OPEN (XP54B)

47

Connection for signal of closing edge safety

device

Gate travelling direction CLOSE (XP 54A)

Attention!

If an 8.2 kΩ contact strip closing edge

safety device is connected, the 8.2 kΩ

resistors installed at terminals XP54B

closing edge OPEN and XP54A closing

edge CLOSE must be removed.

- XP54B

P5

46

- XP54A

P5 47

8K2

- XP54B

P5

46

8K2

6.2 / 8

M07E037

12 Manual for installation and operation, Control x.51 GB (#102668)

Advice:

A two-wire photocell connected to

terminals XP62B / XP62A will be

recognised automatically by the

controls after “Mains On”.

The photocell can be deactivated later

(Level 8 / Menu 1).

If the contacts of a closing prevention

device are open, the gate can no longer

be closed.

Label Type / function

P6 GND connection

26

Connection for photocell signal

gate travelling direction OPEN (XP62B)

27

Connection for signal of photocell, gate

travelling direction CLOSE (XP62A)

RX Receiver for the two-wire photocell

TX Transmitter for the two-wire photocell

Terminals XP62A / XP62B

- XP62A

P6 27

TX

RX

- W1

2

1

- W2

2

1

2

- W1

- W2

- AP27

-

- XP62B

P6 26

TX

RX

- W1

2

1

- W2

2

1

- AP26

6.2 / 9

M07E036

6. Installation

Manual for installation and operation, Control x.51 GB (#102668) 13

• Fix the leads in the motor and rpm detector plugs.

6.3 / 3

Attention!

To ensure that the operator system

functions properly, the polarity of the

plugs must be correct.

Terminal Colour system

Number

system

A1 White lead 1

A2 Brown lead 2

V5 Red lead / Grey lead 3 / 6

11 Black lead 4

15 Blue lead 7

10 Pink lead / Lilac lead

5 / 8

6.3 Connecting the motor unit to the

controls

• Pull the cables out of the motor and rpm detector

plugs.

6.3 / 1

Advice:

For double wing gate systems, both

motor supply cables must be laid to the

control unit.

6.3 / 2

• Feed the cables from the motor units into the control

unit through the screw fixings.

Attention!

In order to guarantee the protection

grade of the controls, the cable must

be passed through the correct screw

fixing.

6. Installation

1

2

3

4

5

6

7

8

1

2

1

2

3

4

5

6

7

8

1

2

L

N

PE

15

16 17

P

6.3 / 4

B

C

XV51B

XM70B

XM70A

XV51A

Label Type / function

B

Control module SLAVE

(only for double wing gates)

C Control module MASTER

XM70A Connection for motor unit (Master)

XM70B Connection for motor unit (Slave)

XV51A

Connection for RPM/

reference point sensor (MASTER)

XV51B

Connection for RPM/

reference point sensor (SLAVE)

PE

N

L

15

16

17

Attention!

If the gate system is to function

properly, the following points must be

assured:

- For single wing gate systems, the

motor unit must always be connected

to the MASTER terminal (XM70A and

XV51A).

- For double wing gate systems, the

overlapping (D) must be observed

when connecting the motor units.

E Gate wing motor unit SLAVE (XM70B)

F Gate wing motor unit MASTER (XM70A)

6.3 / 7

• Connect the motor units to the controls.

XM70B

XM70A

XV51A

XV51B

6.3 / 5

6.3 / 6

D

FE

D

EF

14 Manual for installation and operation, Control x.51 GB (#102668)

7.1 Operation and accessories

Caution!

Children are not allowed to operate the

hand transmitters!

Before operating the hand transmitter,

make sure that there are neither

persons nor objects in the operating

range of the gate.

A

D

B

D

C

7.1 / 1

7. Hand transmitter

A Operating button - large

B Operating button - small

C Battery - transmission control light

D Transmission socket

Another operator system can be operated using the

second operating button.

Overview

Reference:

The procedure for programming hand

transmitters (remote controls) to

operate the operator system is

described in Section 8.5.3.

i

Attention!

In order to guarantee the protection

grade of the controls, the cable must

be passed through the correct screw

fixing.

• Feed the cable through the screw fitting into the

control unit.

6.4 Connection of the mains cable

Caution!

- During cabling works, the supply

cables must be disconnected from the

power supply. It must be ensured that

the cables remain disconnected from

the supply for the duration of the

cabling works.

- The fixed connection of a mains

supply requires a universally poled

mains disconnection facility.

6. Installation

L

N

PE

15

16 17

• Connect the power supply leads to the control unit.

• Connect the control unit to the electricity supply.

Advice:

All the control lights are lit for

approximately 3 seconds.

LED 8 then lights up.

6.4 / 1

Manual for installation and operation, Control x.51 GB (#102668) 15

1

E Back of hand transmitter

F Battery 3V CR 2032

• Open the back of the hand transmitter (E),

e.g. with a coin.

• Change the battery (F) and observe correct poling.

F

E

Visor clip, for attaching the hand transmitter to a visor

in a car.

7.1 / 2

7.1 / 3

Accessory

Change batteries

7. Hand transmitter

7.2 Hand transmitter coding

7.2.1 Transfer the coding

Advice:

The plug connections on both sides of

the hand transmitter are identical.

Using this function it is possible to transfer the coding

of a hand transmitter that has already been

programmed for operating the operator system

(master transmitter) to another hand transmitter.

• Connect both transmitters with the enclosed

transmission plug.

Caution!

Before operating the hand transmitter,

ensure that there are neither persons

nor objects in the operating range of

the gate.

7.2.1 / 1

16 Manual for installation and operation, Control x.51 GB (#102668)

7.2.2 Change coding

If a hand transmitter has been lost, this function can

be used to change the coding of the remaining remote

control transmitters.

• Connect one end of the transmission plug to the

hand transmitter.

• At the free end of the transmission plug, short-circuit

one of the outer pins with the centre pin adjacent to

it (e.g. using a screw driver).

• Press the desired button on the hand transmitter.

A new code is then generated by the integrated

random coding facility.

The LED flashes quickly.

As soon as the LED lights up permanently, the hand

transmitter has been programmed with a new code.

The button can then be released and the transmission

plug removed.

Advice:

After the hand transmitter has been

re-programmed, the operator system

must also be re-programmed to

respond to the new code.

For multi-channel transmitters, the

programming process must be carried

out for each button separately.

7.2.2 / 1

7. Hand transmitter

Advice:

For multi-channel hand transmitters,

the coding procedure has to be carried

out for each button separately.

• Actuate the master transmitter and hold the button.

The transmitter LED lights up.

• Whilst keeping the button on the master transmitter

depressed, press the desired button on the other

hand transmitter.

The LED flashes.

After 1 -2 seconds, the LED on the newly programmed

transmitter lights up permanently.

The programming procedure is complete.

The coding of the master transmitter has now been

transferred to the other hand transmitter.

• Remove the transmission plug.

7.2.1 / 2

7.2.1 / 3

Manual for installation and operation, Control x.51 GB (#102668) 17

P

E

N

L

1

5

1

6

1

7

8.2 Overview of the control unit

8.1 / 1

A

B

• Insert the modular antenna (A) into the antenna

socket (B) in the controls.

8.1 Connecting the modular antenna

8. Initial operation

P

1

2

3

4

5

6

7

8

1

2

BAD

C

8.2 / 1

Operating elements

Label Type / function

i

A Carousel display 8.3

B

OPEN button (+)

(e.g. to drive the gate to

the OPEN position or to

increase parameters when

programming)

-

C

CLOSE button (-)

(e.g. to drive the gate to

the CLOSED position or to

decrease parameters when

programming)

-

D

STOP button (p)

(e.g. to switch to

programming mode or

to save parameters)

-

18 Manual for installation and operation, Control x.51 GB (#102668)

8. Initial operation

8.4 Reference point

In operating mode, LED 5 lights up briefly

when an object/person passes the reference

point.

Advice:

In the factory default setting and after

a reset, the controls are set to start in

the CLOSED gate position.

To ensure trouble-free programming,

therefore, the gate and the operator

system must be in the CLOSED end

position before resetting or carrying out

the express programming procedure.

Photocell or the CESD has been interrupted

(display: master only)

Gate moving towards OPEN position

(display: master and slave)

Gate in OPEN position

(display: master and slave)

Gate moving towards CLOSED position

(display: master and slave)

Gate in CLOSED position

(display: master and slave)

Reference point is switched

(display: master and slave)

Permanent actuation of an external control

element (display: master only)

Remote control is actuated

(display: master only)

Operating voltage

(display: master and slave)

LED displays in operating mode

Legend:

LED off

LED on

LED flashes slowly

LED pulses

LED flashes quickly

Factory default setting

Not possible –

8.3 Overview of the display functions

Manual for installation and operation, Control x.51 GB (#102668) 19

8. Initial operation

8.5 Express programming

Test run (only necessary after resetting)

Before carrying out the express programming procedure,

the drive system (with the gate coupled up) must be

driven to the factory default OPEN and CLOSED gate

positions using the (+) and (-) buttons.

• Carry out a test run (MASTER and SLAVE).

Express programming

The basic functions of the operator system are set

during the express programming procedure.

MASTER:

- Gate position GATE OPEN

- Gate position GATE CLOSED

- Remote controls

SLAVE (only for double wing gates):

- Gate position GATE OPEN

- Gate position GATE CLOSED

The programming procedure is a consecutive process.

It is essential that this procedure be carried out.

After express programming has been completed and a

learning run has been carried out to set the automatic

cut-out at the OPEN and CLOSED gate positions, the

operator system is ready for operation.

8.5.1 General notes on express programming

Advice:

When programming the OPEN and

CLOSED gate positions, the reference

point must be passed.

8.5.2 Programming buttons

The controls are programmed using the plus (+),

minus (-) and (P) buttons.

If no buttons are pressed within 120 seconds while in

programming mode, the controls revert to operating

mode.

A corresponding message is displayed.

Reference:

The messages are explained in

Section 10.

i

Advice:

For proper initial operation of the

operator system, the express

programming procedure must be

carried out.

• Carry out the express programming according to the

following procedure.

Legend:

LED off

LED on

LED flashes slowly

LED pulses

LED flashes quickly

Factory default setting

Not possible –

20 Manual for installation and operation, Control x.51 GB (#102668)

Page is loading ...

Marantec Control x.51 Owner's manual

Marantec Control x.51 Owner's manual

Related papers

Other documents