model
CFM1
COFFEE MILL
Important safeguards
9. Do not operate the appliance with a
damaged cord or plug, and do not use the
appliance if it is damaged in any way. Should
the supply cord become damaged, it must
only be replaced by the manufacturer, its
service agent or a similarly qualified person.
10. Do not leave the motor switched on for
longer than a minute without interruption.
11. The use of attachments not recommended or
sold by the manufacturer may cause fire,
electric shock or injury.
12. This coffee mill is intended for household use
only. Do not use this appliance other than for
its intended use.
13. Do not use outdoors.
SAVE THESE INSTRUCTIONS FOR
FUTURE REFERENCE
1. Read and understand all the instructions
before using your Hitachi Coffee Mill.
2. Check the coffee bean Container for presence
of foreign objects before using.
3. Keep your Coffee Mill out of children’s reach.
Never let children use this appliance.
4. To protect against the risk of electrical shock,
do not immerse the coffee mill into water or
any other liquid.
5. Ensure the voltage shown on the rating label
on the underside of the appliance is the same
as the mains outlet in your home.
6. Avoid contact with moving parts.
7. Place the appliance on a stable flat surface
and do not let the cord hang over the edge of
a table or counter.
8. Do not let the cord come into contact with hot
surfaces, including the stove.
i
2
1. Container Cover
2. Coffee Bean
Container
3. Grinding Cone
4. Coarse/
Fine Control Knob
5. Power Cord
6. Cancel Button
7. Start Button
8. Cup Quantity
Control Knob
9. Ground Coffee Cup
Information
3
4
5
6
7
8
9
1
Know your Coffee Mill
(Note: For products sold outside
the UK this plug will be 2 pin.)
Using your Coffee Mill
Before using your
Hitachi Coffee Mill
• Read Important Safeguards.
• Plug into a mains outlet.
Recommended settings:
• Pump driven espresso
machines. Fine grind.
Setting “A”.
• Cone filter drip coffee,
steam espresso
machines, stovetop
espresso makers. Fine
grind. Setting “B”.
• Flat-bottom filter drip
coffee machines.
Medium grind.
Setting “C”.
• Coffee press. Coarse
grind. Setting “E”.
i
Information
Loading the Coffee Mill
• Open the Container Lid (1)
and pour the coffee beans
into the container (2).
• Take care not to load the
coffee beans over the “Max”
mark, located on the side of
the container.
• Close the Container Lid,
making sure it is closed tightly.
Adjusting the fineness
of your coffee
• Adjust the desired degree of
grinding (coarse, medium,
fine), using Coarse/Fine
Control Knob (4), located at
the rear of the Coffee Mill.
The setting is displayed on the
top side of the Control Knob.
Using your Coffee Mill
Selecting grind
capacity for number
of cups
• Your Coffee Mill has settings
for grinding from 1 to 12
cups. Adjust the Control Knob
(8) to the corresponding
number of cups desired.
• When the knob is at the
“OFF” position, the appliance
will not operate.
OFF
12
•
10
•
8
•
6
•
4
•
2
•
Grinding
• To grind the coffee beans,
press the Start Button (6).
• To interrupt the grinding
operation, press the Cancel
Button (7).
• Grinding for 12 cups will take
approximately 1 minute. After
continuous operation for over
1 minute, leave the unit to
cool for at least 1 minute,
to prevent the motor from
overheating.
• Always unplug your
Coffee Mill after use.
Emptying
• Gently tap the Cup (9) 3 or
4 times with the palm of your
hand before removing the
Cup and tipping out the
freshly ground coffee.
Note: If this container is
overfilled or the appliance is
operated for long periods the
unit will cut out and will need to
be left to cool for 10 minutes
before it can be used again.
Tips on grinding
coffee beans
Great tasting coffee
• To maintain freshness, coffee
beans can be stored in the
freezer. The beans do not
need to be defrosted before
grinding.
• When grinding large amounts
of beans for later use, store it
in an airtight container. Place
the container in the freezer, or
in a cool area, away from
contact with light.
• Keep coffee beans dry. Do not
use wet coffee beans.
• Adjust the amount of coffee
used for each cup to suit your
own personal taste.
Cleaning instructions
• Always unplug your coffee
mill before cleaning.
• To clean the grinding
mechanism, remove the
Grinding Cone (3) from the
Container, by rotating it
clockwise, as indicated on
the Cone. Then clean the
grinding mechanism and
the outlet chute with a small
brush.
Never immerse the Mill in
water or any other liquid,
or place in dishwasher.
i
Information
• To clean the Container, wipe
it using a soft dry cloth.
• After the Grinding Cone has
completely dried, return it to
the grinding mechanism in the
Container. Lock it into position
by turning the Cone
anti-clockwise, as indicated
on the Cone, until it will not
turn anymore.
• Only wash the removable
part of the Coffee Mill.
To clean the Cup, dip it into
warm water and use only
non-abrasive cleaners and a
clean cloth to wash it.
SYMPTOM
The Coffee Mill does not
operate.
Grind quality is poor.
POSSIBLE CAUSE
Appliance is not
plugged in.
The cup quantity control
is set to ”off”.
The safety cut-out has
operated.
Fuse needs replacing.
Grinding mechanism is
dirty.
SOLUTION
Check that the Coffee
Mill is plugged in
properly.
Turn this control to
1-12 cups.
Leave to cool for 10
minutes. Make sure
operating cycles do
not exceed 1 minute.
Make sure the grand
coffee container has
not been overfilled.
Empty and leave to
cool for 10 minutes.
Replace the 3A fuse.
Clean the grinding
mechanism.
Troubleshooting and specifications
TROUBLESHOOTING SPECIFICATIONS
AC supply: 230V ~ 50Hz
Power input: 85W
Unit dimension: 170 (L) x 100 (W) x 250 (H)
We continually strive to improve our products,
specifications may change without prior notice.
Note: This product is exclusively available through Dixons
Stores Group. In the unlikely event of a problem with your
product please return to the store where your purchase was
made.
Partmaster Direct can provide accessories, spares, batteries
and replacement parts with Next Day Delivery available upon
request.
Please call: 0870 600 1338 (UK customers only)
Calls charged at National Rate…or visit our website at
www.partmaster.co.uk
/