2. Vision Fitness
  3. X10

Vision Fitness X10 Assembly Manual

  • Hello! I am an AI chatbot trained to assist you with the Vision Fitness X10 Assembly Manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Screwdriver
5mm
L-Shaped
Wrench
13/15mm Wrench
8mm
L-Shaped
Wrench
ASSEMBLY GUIDE
HARDWARE INCLUDED
X10
Elliptical Trainer
X10 ASSEMBLY GUIDE
TOOLS & PARTS INCLUDED
1600 Landmark Drive
Cottage Grove, WI 53527
toll free 800.335.4348 • fax 608.839.8731
www.visionfitness.com
©2012 Vision Fitness. All Rights Reserved.
2012.06.14 REV1.3
PARTS BOX
Front Stabilizer Tube (1)
Rear Stabilizer Cover (1)
Guide Rail Set (1)
Guide Rail Cover (1)
Pedal Arms (2)
Pedal Arm Covers (2 sets)
Console Mast (1)
Lower Handlebars (2)
Handlebar Caps (2)
Lower Link Arms With
Footpads (2)
Side Pedal Covers (2)
Upper Handlebars (2)
Hardware Clamshell (1)
Water Bottle Cage (1)
Top Cap (1)
Mast Boot (1)
Power Cord (1)
HARDWARE INCLUDED
X10
Elliptical Trainer
To avoid possible damage to this Elliptical Trainer, please follow assembly steps in the correct order. Before proceeding though, find your
new Elliptical Trainer’s two serial numbers located on the front axle tube, and on the back side of the console, and enter here:
Refer to this number when calling for service. Be sure to read your Owner’s Guide before using your new Elliptical Trainer.
If any parts, hardware or tools are missing, please call 1.800.335.4348
NOTE: It is recommended that you apply grease to the threads of each bolt and screw as you assemble your Elliptical Trainer to prevent
loosening and noise. Also, during each assembly step, ensure that ALL bolts and screws are in place and partially threaded in before
completely tightening any ONE bolt or screw.
Frame Serial Number
Console Serial Number
M8x25mm Oval Hex
Socket Bolt. Quantity: 4
8.4x17.0x1.0t Arc Washer.
Quantity: 4
QTY:4
QTY:4
Z02. 8.4×17.0×1.0t Arc Washer
Z01. M8×25mm Oval Hex Socket Bolt
QTY:4
QTY:4
QTY:4
Z03. M10×25mm Round Hex Socket Bolt
Z04. 10.2×20.0×1.5t Fat Washer
Z05. 10.2×18.4×2.5t Spring Washer
QTY:2
QTY:2
Z06. 4×12mm Oval Cross Tapping Screw
QTY:2
QTY:2
QTY:2
QTY:2
Z12. 8.2×15.4×2.0t Spring Washer
Z13. M8×20mm Bolt Oval Hex Socket Bolt
Z10. 17.2×22.5×0.3t Wave Washer
Z11. 8.2×20×1.5t Fat Washer
Z09. 4×0.7×15mm Oval Cross Bolt
QTY:4
QTY:4
Z02. 8.4×17.0×1.0t Arc Washer
Z01. M8×25mm Oval Hex Socket Bolt
QTY:4
QTY:4
QTY:4
Z03. M10×25mm Round Hex Socket Bolt
Z04. 10.2×20.0×1.5t Fat Washer
Z05. 10.2×18.4×2.5t Spring Washer
QTY:2
QTY:2
Z06. 4×12mm Oval Cross Tapping Screw
QTY:2
QTY:2
QTY:2
QTY:2
Z12. 8.2×15.4×2.0t Spring Washer
Z13. M8×20mm Bolt Oval Hex Socket Bolt
Z10. 17.2×22.5×0.3t Wave Washer
Z11. 8.2×20×1.5t Fat Washer
Z09. 4×0.7×15mm Oval Cross Bolt
M10x25mm Round Hex Socket Bolt.
Quantity: 4
10x18.4x2.5t Spring
Washer. Quantity: 4
QTY:4
QTY:4
Z02. 8.4×17.0×1.0t Arc Washer
Z01. M8×25mm Oval Hex Socket Bolt
QTY:4
QTY:4
QTY:4
Z03. M10×25mm Round Hex Socket Bolt
Z04. 10.2×20.0×1.5t Fat Washer
Z05. 10.2×18.4×2.5t Spring Washer
QTY:2
QTY:2
Z06. 4×12mm Oval Cross Tapping Screw
QTY:2
QTY:2
QTY:2
QTY:2
Z12. 8.2×15.4×2.0t Spring Washer
Z13. M8×20mm Bolt Oval Hex Socket Bolt
Z10. 17.2×22.5×0.3t Wave Washer
Z11. 8.2×20×1.5t Fat Washer
Z09. 4×0.7×15mm Oval Cross Bolt
QTY:4
QTY:4
Z02. 8.4×17.0×1.0t Arc Washer
Z01. M8×25mm Oval Hex Socket Bolt
QTY:4
QTY:4
QTY:4
Z03. M10×25mm Round Hex Socket Bolt
Z04. 10.2×20.0×1.5t Fat Washer
Z05. 10.2×18.4×2.5t Spring Washer
QTY:2
QTY:2
Z06. 4×12mm Oval Cross Tapping Screw
QTY:2
QTY:2
QTY:2
QTY:2
Z12. 8.2×15.4×2.0t Spring Washer
Z13. M8×20mm Bolt Oval Hex Socket Bolt
Z10. 17.2×22.5×0.3t Wave Washer
Z11. 8.2×20×1.5t Fat Washer
Z09. 4×0.7×15mm Oval Cross Bolt
QTY:4
QTY:4
Z02. 8.4×17.0×1.0t Arc Washer
Z01. M8×25mm Oval Hex Socket Bolt
QTY:4
QTY:4
QTY:4
Z03. M10×25mm Round Hex Socket Bolt
Z04. 10.2×20.0×1.5t Fat Washer
Z05. 10.2×18.4×2.5t Spring Washer
QTY:2
QTY:2
Z06. 4×12mm Oval Cross Tapping Screw
QTY:2
QTY:2
QTY:2
QTY:2
Z12. 8.2×15.4×2.0t Spring Washer
Z13. M8×20mm Bolt Oval Hex Socket Bolt
Z10. 17.2×22.5×0.3t Wave Washer
Z11. 8.2×20×1.5t Fat Washer
Z09. 4×0.7×15mm Oval Cross Bolt
10.2x20.0x1.5t Flat
Washer. Quantity: 4
4x12mm Oval Cross
Tapping Screw. Quantity:
2
QTY:4
QTY:4
Z02. 8.4×17.0×1.0t Arc Washer
Z01. M8×25mm Oval Hex Socket Bolt
QTY:4
QTY:4
QTY:4
Z03. M10×25mm Round Hex Socket Bolt
Z04. 10.2×20.0×1.5t Fat Washer
Z05. 10.2×18.4×2.5t Spring Washer
QTY:2
QTY:2
Z06. 4×12mm Oval Cross Tapping Screw
QTY:2
QTY:2
QTY:2
QTY:2
Z12. 8.2×15.4×2.0t Spring Washer
Z13. M8×20mm Bolt Oval Hex Socket Bolt
Z10. 17.2×22.5×0.3t Wave Washer
Z11. 8.2×20×1.5t Fat Washer
Z09. 4×0.7×15mm Oval Cross Bolt
4x10mm Oval Cross Bolt.
Quantity: 2
QTY:4
QTY:4
Z02. 8.4×17.0×1.0t Arc Washer
Z01. M8×25mm Oval Hex Socket Bolt
QTY:4
QTY:4
QTY:4
Z03. M10×25mm Round Hex Socket Bolt
Z04. 10.2×20.0×1.5t Fat Washer
Z05. 10.2×18.4×2.5t Spring Washer
QTY:2
QTY:2
Z06. 4×12mm Oval Cross Tapping Screw
QTY:2
QTY:2
QTY:2
QTY:2
Z12. 8.2×15.4×2.0t Spring Washer
Z13. M8×20mm Bolt Oval Hex Socket Bolt
Z10. 17.2×22.5×0.3t Wave Washer
Z11. 8.2×20×1.5t Fat Washer
Z09. 4×0.7×15mm Oval Cross Bolt
17x23x0.5t Wavy Washer.
Quantity: 2
QTY:4
QTY:4
Z02. 8.4×17.0×1.0t Arc Washer
Z01. M8×25mm Oval Hex Socket Bolt
QTY:4
QTY:4
QTY:4
Z03. M10×25mm Round Hex Socket Bolt
Z04. 10.2×20.0×1.5t Fat Washer
Z05. 10.2×18.4×2.5t Spring Washer
QTY:2
QTY:2
Z06. 4×12mm Oval Cross Tapping Screw
QTY:2
QTY:2
QTY:2
QTY:2
Z12. 8.2×15.4×2.0t Spring Washer
Z13. M8×20mm Bolt Oval Hex Socket Bolt
Z10. 17.2×22.5×0.3t Wave Washer
Z11. 8.2×20×1.5t Fat Washer
Z09. 4×0.7×15mm Oval Cross Bolt
QTY:4
QTY:4
Z02. 8.4×17.0×1.0t Arc Washer
Z01. M8×25mm Oval Hex Socket Bolt
QTY:4
QTY:4
QTY:4
Z03. M10×25mm Round Hex Socket Bolt
Z04. 10.2×20.0×1.5t Fat Washer
Z05. 10.2×18.4×2.5t Spring Washer
QTY:2
QTY:2
Z06. 4×12mm Oval Cross Tapping Screw
QTY:2
QTY:2
QTY:2
QTY:2
Z12. 8.2×15.4×2.0t Spring Washer
Z13. M8×20mm Bolt Oval Hex Socket Bolt
Z10. 17.2×22.5×0.3t Wave Washer
Z11. 8.2×20×1.5t Fat Washer
Z09. 4×0.7×15mm Oval Cross Bolt
QTY:4
QTY:4
Z02. 8.4×17.0×1.0t Arc Washer
Z01. M8×25mm Oval Hex Socket Bolt
QTY:4
QTY:4
QTY:4
Z03. M10×25mm Round Hex Socket Bolt
Z04. 10.2×20.0×1.5t Fat Washer
Z05. 10.2×18.4×2.5t Spring Washer
QTY:2
QTY:2
Z06. 4×12mm Oval Cross Tapping Screw
QTY:2
QTY:2
QTY:2
QTY:2
Z12. 8.2×15.4×2.0t Spring Washer
Z13. M8×20mm Bolt Oval Hex Socket Bolt
Z10. 17.2×22.5×0.3t Wave Washer
Z11. 8.2×20×1.5t Fat Washer
Z09. 4×0.7×15mm Oval Cross Bolt
8x20x1.5t Flat Washer.
Quantity: 2
8x15x2t Spring
Washer. Quantity:
2
M8x20mm Oval Hex
Socket Bolt. Quantity: 2
QTY:4
QTY:2
QTY:2
QTY:2
QTY:4
QTY:2
QTY:2
QTY:2
QTY:2
Z20. M8×70mm Oval Hex Socket Bolt
Z21. 8.2×15.4×2.0t Spring Washer
Z22. 8.4×17.0×1.0t Flat Washer
Z23. M8 Nylon Nut
Z24. 15.9×28.4×1.0t Teon Washer
Z25. M8×20mm Oval Hex Socket Bolt
Z26. 8.2×20.0×1.5t Flat Washer
Z32. 20.2×27.2×1.5t Flat Washer
Z33. 20.7×29.1×0.3t Wavy Washer
QTY:4
QTY:2
QTY:2
QTY:2
QTY:4
QTY:2
QTY:2
QTY:2
QTY:2
Z20. M8×70mm Oval Hex Socket Bolt
Z21. 8.2×15.4×2.0t Spring Washer
Z22. 8.4×17.0×1.0t Flat Washer
Z23. M8 Nylon Nut
Z24. 15.9×28.4×1.0t Teon Washer
Z25. M8×20mm Oval Hex Socket Bolt
Z26. 8.2×20.0×1.5t Flat Washer
Z32. 20.2×27.2×1.5t Flat Washer
Z33. 20.7×29.1×0.3t Wavy Washer
M8x72mm Oval Hex Socket Bolt.
Quantity: 2
QTY:4
QTY:2
QTY:2
QTY:2
QTY:4
QTY:2
QTY:2
QTY:2
QTY:2
Z20. M8×70mm Oval Hex Socket Bolt
Z21. 8.2×15.4×2.0t Spring Washer
Z22. 8.4×17.0×1.0t Flat Washer
Z23. M8 Nylon Nut
Z24. 15.9×28.4×1.0t Teon Washer
Z25. M8×20mm Oval Hex Socket Bolt
Z26. 8.2×20.0×1.5t Flat Washer
Z32. 20.2×27.2×1.5t Flat Washer
Z33. 20.7×29.1×0.3t Wavy Washer
8x15x2t Spring Washer.
Quantity: 4
QTY:4
QTY:2
QTY:2
QTY:2
QTY:4
QTY:2
QTY:2
QTY:2
QTY:2
Z20. M8×70mm Oval Hex Socket Bolt
Z21. 8.2×15.4×2.0t Spring Washer
Z22. 8.4×17.0×1.0t Flat Washer
Z23. M8 Nylon Nut
Z24. 15.9×28.4×1.0t Teon Washer
Z25. M8×20mm Oval Hex Socket Bolt
Z26. 8.2×20.0×1.5t Flat Washer
Z32. 20.2×27.2×1.5t Flat Washer
Z33. 20.7×29.1×0.3t Wavy Washer
M8 Nylon Nut. Quantity: 2
16x28x1t Teflon Washer.
Quantity: 4
QTY:4
QTY:2
QTY:2
QTY:2
QTY:4
QTY:2
QTY:2
QTY:2
QTY:2
Z20. M8×70mm Oval Hex Socket Bolt
Z21. 8.2×15.4×2.0t Spring Washer
Z22. 8.4×17.0×1.0t Flat Washer
Z23. M8 Nylon Nut
Z24. 15.9×28.4×1.0t Teon Washer
Z25. M8×20mm Oval Hex Socket Bolt
Z26. 8.2×20.0×1.5t Flat Washer
Z32. 20.2×27.2×1.5t Flat Washer
Z33. 20.7×29.1×0.3t Wavy Washer
QTY:4
QTY:2
QTY:2
QTY:2
QTY:4
QTY:2
QTY:2
QTY:2
QTY:2
Z20. M8×70mm Oval Hex Socket Bolt
Z21. 8.2×15.4×2.0t Spring Washer
Z22. 8.4×17.0×1.0t Flat Washer
Z23. M8 Nylon Nut
Z24. 15.9×28.4×1.0t Teon Washer
Z25. M8×20mm Oval Hex Socket Bolt
Z26. 8.2×20.0×1.5t Flat Washer
Z32. 20.2×27.2×1.5t Flat Washer
Z33. 20.7×29.1×0.3t Wavy Washer
M8x20mm Oval Hex Socket Bolt.
Quantity: 2
8x20x3t Flat Washer.
Quantity: 4
QTY:4
QTY:2
QTY:2
QTY:2
QTY:4
QTY:2
QTY:2
QTY:2
QTY:2
Z20. M8×70mm Oval Hex Socket Bolt
Z21. 8.2×15.4×2.0t Spring Washer
Z22. 8.4×17.0×1.0t Flat Washer
Z23. M8 Nylon Nut
Z24. 15.9×28.4×1.0t Teon Washer
Z25. M8×20mm Oval Hex Socket Bolt
Z26. 8.2×20.0×1.5t Flat Washer
Z32. 20.2×27.2×1.5t Flat Washer
Z33. 20.7×29.1×0.3t Wavy Washer
20x27x1.5t Flat Washer.
Quantity: 2
QTY:4
QTY:2
QTY:2
QTY:2
QTY:4
QTY:2
QTY:2
QTY:2
QTY:2
Z20. M8×70mm Oval Hex Socket Bolt
Z21. 8.2×15.4×2.0t Spring Washer
Z22. 8.4×17.0×1.0t Flat Washer
Z23. M8 Nylon Nut
Z24. 15.9×28.4×1.0t Teon Washer
Z25. M8×20mm Oval Hex Socket Bolt
Z26. 8.2×20.0×1.5t Flat Washer
Z32. 20.2×27.2×1.5t Flat Washer
Z33. 20.7×29.1×0.3t Wavy Washer
8.5x20x1t Flat
Washer. Quantity: 2
8.6x26x2t Flat
Washer. Quantity:
2
8x15x2t Spring
Washer. Quantity:
2
M8x20mm Oval
Hex Socket Bolt.
Quantity: 2
20x27x1.5t Flat
Washer. Quantity:
4
20.7x29x0.5t Wavy
Washer. Quantity: 2
STEP 4
STEP 5
STEP 3
STEP 2
STEP 1
20.7x29x0.5t Wavy
Washer. Quantity: 2
Upper
Handlebars
Handlebars
Boots
Top Cap
Lower
Handlebars
Cup Holder
Console Cables
STEP 6
STEP 7
STEP 7
HARDWARE IS PRE-INSTALLED
Attach Console
• With the screwdriver, remove the
four console mounting screws from
the backside of the console. Connect
the heart rate wires coming from the
mast to the heart rate wires coming
from the bottom of the console. Plug
the data cables into the board. Pull
any extra wire down into the console
mast. Secure console to the bracket
using the four console mounting
screws removed earlier. Tighten with
the screwdriver.
• Plug the power cord into the power
socket in the front of the unit. Plug
the other end of the cord into the
wall outlet. Make sure the power
switches at the bottom of the unit
and on the back of the console are in
the on position.
STEP 6
HARDWARE IS PRE-INSTALLED
Attach Upper Handlebars
• Slide upper handlebar onto lower
handlebar and align notch with tab
making sure handlebars are joined
together completely. Secure upper
handlebars to lower handlebars
using pre-installed set screws
• Slide handlebar boots down
• Repeat on other side
Attach Top Cap
• Slide top cap over console mast and
snap into place.
• Insert console mast boot over top
cap and snap into place.
• Attach Cup holder using 2 pre-
installed screws
COMPLETE
STEP 8
• Refer to Product Selection and Model
Configuration decal on console or
follow these steps.
• Once the product is plugged in turn on
the console
• Select elliptical (EP) using the
resistance arrow keys. Press ENTER
to select.
• Select model (X10) using the
RESISTANCE arrow keys. Press ENTER
to select. Console will reset to start-up
screen.
• The product selection and model
configuration is now complete.
STEP 1
OPEN HARDWARE FOR STEP 1
Attach Rear Stabilizer Cover
• Place rear stabilizer cover over rear
stabilizer as shown
• Attach the rear stabilizer cover using
2 screws
Attach Guide Rail Set
• Align guide rail set with main frame
as shown
• Attach the guide rail set to the main
frame using 4 bolts, 4 spring washers
and 4 flat washers
• Attach the guide rail cover to the
main frame using 2 bolts
Console Mast
Bracket
Console Mast
Pedal Arm
Crank
Pedal Arm
Covers
Data Cable
Console Mast
Lower
Handlebar
Handlebar
Cap
Link Arm
Pedal Arm
Bracket
Lower
Handlebars
Side Pedal
Cover
Front Stabilizer Tube
Front Stabilizer
Bracket
Guide Rail Set
Main Frame Guide Rail Cover
Rear Stabilizer
Cover
Please follow the order and intent of these instructions
as much as you can. The order of assembly and order
of tightening the bolts will affect the performance of
your new exercise machine.
Pre-Attached Bolt
and Washers
Teflon
Washers
Flat Washer
Spring Washer
Nut
Bolt
Link Arm
STEP 2
OPEN HARDWARE FOR STEP 2
Attach Levelers to Stabilizer Tube
• Screw both levelers into the holes
in the bottom of the front stabilizer
tube
Attach Front Stabilizer Tube
• Attach the front stabilizer tube to
the front stabilizer bracket using 4
bolts and 4 arc washers
STEP 3
OPEN HARDWARE FOR STEP 3
Attach Pedal Arms
• Slide wavy washer over crank
followed by pedal arm as shown.
Rest pedal arm wheel on guide rail
• Attach the pedal arm to the crank
using 1 flat washer, 1 spring washer
and 1 bolt
• Repeat on other side
Attach Console Mast
• Tie wire to data cable and feed the
connector through the console mast
• Remove 4 pre-attached bolts and
washers. Attach console mast to
console mast bracket with 4 pre-
attached bolts and washers
• Make sure cable is not pinched
between the console mast and
console mast bracket
• Be sure to fully tighten bolts
Attach Pedal Arm Covers
• Make sure holes are on the bottom of
the pedal arm
• Attach the bottom cover first with 2
pre-attached screws
• Snap on top cover
• Repeat on other side
STEP 4
OPEN HARDWARE FOR STEP 4
Attach Lower Handlebars to Console
Mast
• Slide 1 large flat washer, 1 wavy
washer and another large flat washer
onto the console mast
• Slide lower handlebar onto console
mast and attach using 1 large flat
washer, 1 handlebar cap, 1 flat washer,
1 spring washer and 1 bolt
• Repeat on other side
STEP 5
OPEN HARDWARE FOR STEP 5
Attach Link Arms
• Slide wavy washer and 27mm flat
washer onto link arm before sliding
link arm onto pedal arm bracket
• Attach link arm to pedal arm using
1 flat washer, 1 spring washer and 1
bolt
• Align opposite end of link arm
with bracket on bottom of lower
handlebar
• Place Teflon washers on both sides
of the link arm. While holding Teflon
washers slide link arm into bottom
end of lower handlebar
• Secure the joint with 1 bolt, 1 flat
washer, 1 spring washer and secure
with one nut
• Repeat on other side
Attach Side Pedal Covers
• Secure side pedal covers with 2 pre-
attached screws on each side
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
/