T47818 4-Unit Garage System Installation Instructions
Pre-assembly Guidelines
1. Two people may be required to complete the assembly.
2. Throughly read all installation instructions prior to starting
assembly.
3. Read, understand and heed all warnings and safety instructions.
4. Make sure your cabinet will t within the desired location.
5. Plan to assemble the cabinet in the area where it will be used.
Once fully assembled, the cabinet may be difcult to move.
WARNING
Always wear proper eye protection and other applicable
safety equipment while assembling your cabinet.
2
Please take the time to inspect parts before beginning assembly.
Image Part # Description Image Part # Description
T47805 1pc - Tall cabinet T47806 3pc - Wall cabinets
T47808 1pc - 7-Drawer cabinet T47809 1pc - 2-Door cabinet
T47810 6pc - Pegboards T47819
2pc - Rear panels (black)
T47805-06 4pc - Tall cabinet shelves T47809-02 1pc - 2-Door cabinet shelf
T47805-09
1pc - 600mm Front baseboard
(for T47805)
T47805-10
4pc - 500mm Side baseboards
(for T47805)
GS010
2pc - 680mm Front
baseboards (for T47808 &
T47809)
T47814 1pc - MDF worktop
T47811
4pc - 1890mm Connector
posts
GS001 12pc - Adjustable legs
GS002 12pc - Fixed legs GS003 20pc - Shelf brackets
GS004 6pc - Keys GS006
24pc - M6 x 12mm Bolts
(For fixed legs [GS002])
GS007
70pc - M5 x 12mm Bolts
(for connector post [T47811])
GS011
5pc - M4 x 20mm screws
(for MDF worktop [T47814])
GS012
2pc - M4 x 30mm Screws
(for wall connector [GS013])
GS013 2pc - Wall connectors
3
Step 2：Place T47808, T47805 & T47809
according to desired order and position.
Step 3：Install 4 connector posts (T47811) at the
rear of the unit using provided M5 x 12mm bolts
(GS007).
Step 4：Install 2 rear panels (T47819) at the
rear of the unit using provided M5 x 12mm bolts
(GS007).
Step 5：Install 6 pegboards (T47810) using
provided M5 x 12mm bolts (GS007).
Step 6：Install 3 wall cabinets (T47806) using
provided M5 x 12mm bolts (GS007).
Step 7：Attach MDF worktop (T47814).
Step 1：Install adjustable legs (GS001) and fixed
legs (GS002) under T47808, T47805 & T47809.
Use M6 x 12mm bolts (GS006) to fasten fixed legs.
Fasten the interior of tall cabinet (T47805) to the
worktop using supplied screws (GS011). Fasten
the rear of each connector post (T47811) to the
worktop using supplied screws (GS011).
4
Step 9：Set shelf brackets (GS003) according to
desired position in tall cabinet (T47805) and
2-door cabinet (T47809).
Step 10：Set shelves in tall cabinet (T47805) and
2-door cabinet (T47809).
Step 12：After assembly is finished and properly
leveled, align wall connector (GS013) to central
connector post (T47811) and fasten to wall using
M4 x 30mm screws (GS012).
Step 11：If floor is uneven, adjust adjustable legs
(GS001) to desired height.
Step 8：Affix baseboards (T47805-09, T47805-10
and GS010) using provided M5 x 12mm bolts (GS007).
/
