Estate Dryer User Instructions

Brand: Estate

Model: Dryer

Category: Tumble dryers

Type: User Instructions

DRYER USER INSTRUCTIONS

INSTRUCTIONS POUR L'UTILISATEUR DE LA

SECHEUSE

DRYER SAFETY .......................................................................... 1

CONTROL PANEL ...................................................................... 4

CYCLE GUIDE ............................................................................ 5

DRYER USE ................................................................................ 6

DRYER CARE .............................................................................. 7

TROUBLESHOOTING ............................................................... 9

WARRANTY ............................................................................. 11

ASSISTANCE OR SERVICE ....................................... BACK COVER

s_cUr_T_ DELA sI_cHEUsE....................................................12

TABLEAU DE COMMANDE ..................................................... 16

GUIDE DES PROGRAMMES .................................................... 17

UTILISATION DE LA SECHEUSE .............................................. 18

ENTRETIEN DE LA SIECHEUSE ................................................. 19

DEPANNAGE ........................................................................... 21

GARANTIE ............................................................................... 23

ASSISTANCE OU SERVICE ...................... COUVERTURE ARRIIERE

Keep this book and your sales slip together for future reference.

You must provide proof of purchase or installation date for in-

warranty service.

Write down the following information about your appliance to help

ou obtain assistance or service if you ever need it. YOu will need to

_now OUF c *

y omplete model number and serial number. You can find

this information on the model and serial number label, located at

the top inside dryer door well.

Dealer name

Serial number

Address

Phone number

Model number

Purchase date

Conservez.. ce.manuel, et votre re_u. de vente ensemble, pour

reference uiterleure. Pour ie service sousgarantie, vous devez

presenter un document prouvant la date d"achat ou d"installafion.

Inscrivez [es renseignements suivants au sujet de votre apparel[

m6nager pour mieux vous aider _ obtenir assistance ou service en

cas de besoin. Vous devrez connattre [e num6ro de mod?_le et [e

num6ro de s6rie au comp[et. Cette information est donn6e sur [a

plaque signal6tique indiquant [es num6ros de mod?_le et de s6rie,

situ6e dans [e [ogement de [a porte _ ['int6rieur de [a s6cheuse.

Nora du marchand

Num6ro de s6rie

Adresse

Num6ro de t616phone

Num6ro de mod6le

Date d"achat

DRYER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injuw, and tell you what can

happen if the instructions are not followed.

W10287575A

WARNING - "Risk of Fire"

- Clothes dryer installation must be performed by a qualified installer.

- Install the clothes dryer according to the manufacturer's instructions and local codes.

- Do not install a clothes dryer with fle×ible plastic venting materials, if flexible metal

(foil type) duct is installed, it must be of a specific type identified by the appliance

manufacturer as suitable for use with clothes dryers. Flexible venting materials are

known to collapse, be easily crushed, and trap lint. These conditions will obstruct

clothes dryer airflow and increase the risk of fire.

- To reduce the risk of severe injury or death, follow all installation instructions.

- Save these instructions.

IMPORTANT SAFETY iNSTRUCTiONS

WARNING: Toreducetheriskoffire,electricshock,orinjurytopersonswhenusingthedryer,followbasicprecautions,

including the following:

[] Read all instructions before using the dryer.

[] Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute to

a chemical reaction that could cause a load to catch fire.

[] Do not dry articles that have been previously cleaned in,

washed in, soaked in, or spotted with gasoline, dry=

cleaning solvents, or other flammable or explosive

substances as they give off vapors that could ignite or

explode.

[] Do not allow children to play on or in the dryer. Close

supervision of children is necessary when the dryer is

used near children.

[] Before the dryer is removed from service or discarded,

remove the door to the drying compartment.

[] Do not reach into the dryer if the drum is moving.

[] Do not install or store the dryer where it will be exposed

to the weather.

[] Do not tamper with controls.

[] Do not repair or replace any part of the dryer or attempt

any servicing unless specifically recommended in this

Use and Care Guide or in published user=repair

instructions that you understand and have the skills to

carry out.

[] Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric

softener or product.

[] Do not use heat to dry articles containing foam rubber or

similarly textured rubber=like materials.

[] Clean lint screen before or after each load.

[] Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust,

and dirt.

[] The interior of the dryer and exhaust vent should be

cleaned periodically by qualified service personnel.

[] See installation instructions for grounding requirements.

SAVE THESE iNSTRUCTiONS

IMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas

Code, ANSi Z223.1/NFPA 54.

The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National

Electrical Code, ANSI/NFPA 70.

State of California Proposition 65 Warnings:

WARNING: This product contains a chemical known to the State of California to cause cancer.

WARNING: This product contains a chemical known to the State of California to cause birth defects or other reproductive harm.

WARNING: For your safety, the information in this manual must be followed to minimize

the risk of fire or explosion, or to prevent property damage, personal injury, or death.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

- WHAT TO DO iF YOU SMELL GAS:

= Do not try to light any appliance.

= Do not touch any electrical switch; do not use any phone in your building.

= Clear the room, building, or area of all occupants.

= Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

= if you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency, or

the gas supplier.

WARNING: Gas leaks cannot always be detected by smell.

Gas suppliers recommend that you use a gas detector approved by UL or CSA.

For more information, contact your gas supplier.

If a gas leak is detected, follow the "What to do if you smell gas" instructions.

i r i :

Along with heat, dryers require good air flow to efficiently dry

laundry. Proper venting will reduce your drying times and improve

your energy savings. See Installation Instructions.

The venting system attached to the dryer plays a big role in good air

flow.

[]

Replace plastic or foil vent material with 4" (102 mm) diameter

heavy, rigid vent material

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to follow these instructions can result in death

or fire.

Service calls caused by impro3erl venting are not covered by the

warranty and will be 3aid by the customer, regardless of who

installed the dryer.

Maintain Good Air flow by:

[] Cleaning your lint screen before each load.

[] Use the shortest length of vent possible.

[] Use no more than four 90 ° elbows in a vent system; each

bend and curve reduces air flow.

Good Better

[] Remove lint and debris from the exhaust hood.

[] Remove lint from the entire length of the vent system at [east

every 2 years. When cleaning is complete, be sure to follow

the Installation Instructions supplied with your dryer for final

product check.

[] Clear away items from the front the dryer.

CONTROL PANEL

._w Timed Dry

Off Dry 70

Wrinkle Prevent SO

Cool Dowel Damp Dry

Less Dry 20

Energy preferred @ Cool Down

Automatic Setting Off

Very Dry 30

Automatic off io

Dry Air Dry

End of Cycle Signal

e _u

g xz

Temperature Push to Start

fabric

Cool

Automatic tossG_ so Timed Dry

Dn/ D_y/ _ Itigh Heat

II_gh"Deat Very_ 40

Dry 30

Off_ 20

Cool

Le Down

Dry Off

Energy Prefur_ed _'

Automatic Se_mg Very

Automatic off 10 Air Dry

Dry

Low Heat

Not all features and options are available on all models.

Appearance may vary.

Push to Start

Automatic Dry/Auto Sense Dry

The Automatic Dry cycle takes the guesswork out of drying time

and enhances fabric care. The Automatic Dry cycle may be used for

most loads.

The Cycle Selector (Timer) control may be set to ENERGY

PREFERRED, which is good for most fabrics. At the end of the cycle,

you may check the dryness of the load.

[] If the load is drier thanyou like, select a setting closer to [.ess

Dry the next time you dry a similar load.

[] If the load is not as dry as you want, select a Timed cycle to

complete drying and the next time you dry a similar load,

choose a setting closer to Very Dry.

Drying time with an automatic cycle varies according to the type of

fabric, size of load, and temperature setting. On some models, the

temperature is included in the cycle selections.

WRINKLE PREVENT (on some models)

The WRINKI.E PREVENT features will run after your drying cycle

is complete, it periodically starts and stops the dryer, tumbling the

load without heat to help avoid wrinkling.

On some models, WRINKLE PREVENT automatically starts at the

end of the cycle. Opening the door will stop this feature. On other

models, you can set the WRINKI.E PREVENT selector [<nob

toON.

NOTE: A signal will sound periodically when the WRINKLE

PREVENT setting is selected, but only if the End of Cycle signal is

also selected.

Timed Dry

On some models, temperature is included in the cycle selections.

On models with a se[ectab[e temperature knob, you may choose

a setting based on the fabrics in your load. Drying time and

temperature will depend on your dryer model.

You may select a drying temperature based on the fabrics inyour

load. If you are unsure of the temperature to select for a load, select

the lower setting rather than the higher setting.

Temperature Tips

If your dryer has multiple heat settings:

[] A High heat setting may be used for drying heavyweight items

such as towels andwork clothes.

[] A I_ow to Medium heat setting may be used for drying medium-

weight items such as sheets, Blouses, dresses, underwear,

permanent press fabrics, lingerie, and some knits.

[] YOu may use a no heat (air) setting for rubber, plastic, or heat-

sensitive fabrics.

[] I.ine dry bonded or laminated fabrics.

NOTE: If you have questions about drying temperatures for various

loads, refer to the care label directions.

The End of Cycle signal sounds when a cycle is complete. On

some models, the End of Cycle Signal is fixed. On others, the

End of Cycle Signal is selectable and the signal will sound only

if set to On.

If the WRINKLE PREVENT feature is selected and the End of Cycle

Signal is on, the signal sounds every few minutes. The signal sto3sl

when you open the door or turn the Cycle Control knob to Off.

CYCLE GUIDE

Not all cycles and settings are available on all models.

AUTO SENSE DRY or Senses moisture in tile load or air temperature and Shuts off When the load reaches tile selected dryness level.

AUTOMATIC DRY Gives the best drying in the shortest time. Drying time varies based on fabric type, load Size, and dryness

Set_!ng,

Depending on rnodel, temperature may be Selected on Cycle knob or be a Separate Control.

Automatic Dry Jeans, heavy work Gives the best drying in the shortest time. Drying time varies High

High Heat clothes, towels based on fabric type, load size, and dryness setting.

Automatic Dry Casual, shirts, pants, Gives the best drying in the shortest time. Drying time varies Low

Low Heat lightweight items based on fabric type, load size, and dryness setting.

Towe[s Towels, mattress Thoroughly dries extra-heavy items. High

pads, quilts

Very Dry Jeans, heavy work This dryness [eve[ removes more load moisture than Any

clothes the Energy Preferred cycle. Dries heavy seams.

*Energy Preferred Most loads Use this dryness [eve[ as your starting point for automatic Any

Automatic Setting d ryi ng.

Perm Press Medium to Thoroughly dries permanent press and synthetic blends. Low

lightweight

synthetics, permanent

press, no-iron items

Less Dry Most loads AnyThis dryness level removes less moisture than the Energy

Preferred cycle. Seams of garment may feel slightly damp.

Use for loads you may want to complete drying on

a hanger.

TIMED DRY Wi!l run the dryei foi the SPeCified time 0n the Contiol;

Depending on model, temperature may be Selected on cycle knob or be a separate control.

Timed Dry Heavy or bulky items Completes drying if items are still damp. High

High Heat

Timed Dry Small loads, Gently dries delicate items and knits. Low

Low Heat lightweight items

Heavy Dry Large or heavy items Evenly dries large or heavy loads. High

such as thick towels

or robes

Damp Dry Any load Dries items to a damp [eve[ or for items that do not require Any

an entire drying cycle.

WrinkJe Free Any load Helps to smooth out wrinkles from items, such as clothes I_ow or Medium heat

packed in a suitcase or items [eft in the dryer too long. depending on fabrics

in load

No-heat drying. No heatRubber, plastic, heat

sensitive fabrics

AIR DRY or

NO HEAT FLUFF

SPECIAL SETTINGS

TheSe settings are added at the end 0f certain CyCles to reduce wrinkling.

Coo[ Down All loads This is the last step in a cycle that uses heat. The load is No heat

cooled slowly to reduce wrinkling and make it easier to

handle.

WrinkJe Prevent Any load After a cycle is complete, the load is periodically tumbled No heat

to avoid wrinkles until you are ready to remove it.

DRYER USE

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

DO not dry anything that has ever had anything

flammable on it (even after washing).

Failure to follow these instructions can result in death,

e×plosion, or fire.

WARNING: To reduce the risk of fire, electric shock, or injury to

persons, read the IMPORTANT SAFETY INSTRUCTIONS before

operating this dryer.

This guide covers several different models. Your dryer may not have

a[[ of the cycles and features described.

Before using your dryer, wipe the dryer drum with a damp cloth to

remove dust from storing and shipping.

1. Clean lint screen before each load. See "Cleaning the I.int

Screen."

2. I.oad clothes loosely into the dryer and close the door. Do

not pack the dryer. For best results, allow space for clothes to

tumble freely.

3. Turn the Cycle Control knob to the recommended cycle for the

type of load being dried. Use the Energy Preferred Automatic

Setting to dry most heavy to medium-weight fabrics.

4. If your dryer has a Temperature selector, set it to the

recommended setting for the type of fabric being dried. See

"Cycle Guide" for temperature suggestions. On some models,

temperature is included in the cycle selections.

5. (OPTIONAl_) Your dryer may have a Wrinkle Prevent feature

selector. Use this to avoid wrinkling when you are unable to

remove a load from the dryer as soon as it stops.

6. (OPTIONAl_) Your dryer may have an End of Cycle Signal. The

signal is helpful when drying items that should be removed

from the dryer as soon as it stops.

The End of Cycle signal is part of the Start button and is

se[ectab[e. Turn the Start button to ON or OFF. The signal wi[[

sound only if the selector is set to On.

If desired, add fabric softener sheet. Follow package

instructions.

Press the Start button or knob.

Stopping and Restarting

You can stop your dryer anytime during a cycle.

Tostop your dryer

Open the dryer door or turn the Cycle Control knob to OFF.

NOTE: The Cycle Control knob should point to an Off area when

the dryer is not in use.

Fire Hazard

No washer can completely remove oil.

Do not dry anything that has ever had any type of oil on

it (including cooking oils).

items containing foam, rubber, or plastic must be dried

on a clothesline or by using an Air Cycle or No Heat

Fluff Cycle.

Failure to follow these instructions can result in death

or fire.

To restart your dryer

Close the door. Select a new cycle and temperature (if desired).

Press the Start button.

Use the Drying Rack to dry items such as sweaters andpi[[ows

without tumbling. The drum turns, but the drying rack does not

move.

If your mode[ does not have a drying rack, you may be able to

purchase one for your model. To find out whether your mode[

allows drying rack usage and for information on ordering, please

refer to the front page of the manual or contact the dealer from

whom you purchased your dryer.

NOTE: The drying rack must be removed for normal tumbling.

To use the drying rack

1. Place drying rack in dryer.

Slide rear pegs into the dimples on the back wan of the dryer.

I.ower the front legs to rest on the dryer opening.

2. Put wet items on top of drying rack, leaving space between

items. Do not allow items to hang over the edge of the drying

rack. Close the door.

Select a Timed Dry cycle and temperature, or an air cycle.

Items containing foam, rubber, or plastic must be dried on

a clothesline or by using an air cycle. Refer to the following

table.

4. Start the dryer. Reset cycle to complete drying, if needed.

Rack Dry Cycle Temp Time

Washable wool items Timed I_ow 60 min.

(Mock to shape, lay flat Dry

on drying rack)

Stuffed toys/pillows Timed I_ow 60 min.

(cotton or polyester filled) Dry

Stuffed toys/pillows Air N/A 90 min.

(foam rubber filled) (no heat)

DRYER CARE

(iiiiii !!! ii i iii iiii iiiti!i!!!ii:ililil%/i!!!

KeeP dryer area clear and free from items that would block the

air flow for I_r° per dr yer operation. This includes c[earin glgi[es of

laundry in front of the dryer.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Place dryer at least 18 inches (460 ram) above the floor

for a garage installation.

Failure to do so can result in death, explosion, or fire.

Clean lint screen before each load. A screen blocked by lint can

increase drying time.

IMPORTANT:

[] Do not run the dryer with the lint screen loose, damaged,

blocked, or missing. Doing so can cause overheating and

damage to both the dryer and fabrics.

[] If lint falls off the screen into the dryer during removal, check

the exhaust hood and remove the lint. The exhaust hood is

located where the dryer air exits your home.

Every Load Cleaning

Style 1:

1. The lint screen is located on top of the dryer. Pull the lint

screen toward you. Roll lint off the screen with your fingers.

Do not rinse or wash screen to remove [int. Wet lint is hard to

remove.

2. Push the lint screen firmly back into place.

Style 2:

1. The lint screen is located in the door of the dryer. Pull the lint

screen straight up. Roll lint off the screen with your fingers.

Do not rinse or wash screen to remove [int. Wet lint is hard to

remove.

2. Push the lint screen firmly back into place.

AsNeededCleaning

1. Rolllintoffthescreenwithyourfingers.

2. Wetbothsidesoflintscreenwithhotwater.

3. Wetanylonbrushwithhotwaterandliquiddetergent.Scrub

lintscreenwiththebrushtoremoveresiduebuildup.

4. Rinsescreenwithhotwater.

5. Thoroughlydrylintscreenwithacleantowel.Replacescreen

indryer.

1. Applyaliquid,nonflammablehouseholdcleanertothe

stainedareaofthedrumandrubwithasoftclothuntilstainis

removed.

2. Wipedrumthoroughlywithadampcloth.

3. Tumblealoadofcleanclothsortowelstodrythedrum.

NOTE:Garmentsthatcontainloosedyes,suchasdenimbluejeans

orbrightlycoloredcottonitems,maydiscolorthedryerinterior.

Thesestainsarenotharmfultoyourdryerandwillnotstainfuture

loadsofclothes.Drytheseitemsinsideouttoavoiddrumstaining.

iiiR,_i!___ii:_o:'_uiiiiiii_i¸i_i_i:li:ii!ililliiiiiiiiii_i'iii:

From Inside the Dryer Cabinet

Lint should be removed every 2 years, or more often, depending on

dryer usage. Cleaning shouldbe done by a qualified servicer.

From Inside the Exhaust Vent

I.int should be removed every 2 years, or more often, depending on

dryer usage.

'_i_,,_i:i!!_i<i:::iilii_iiii:iiii¸o iiii:_i_iii:ii__iiii_i_d!ih,'!_o _,,'iiiiii'i_i_:iii!ii:(i::::::_iiiii"_::::

Vacation Care

Operate your dryer only when you are at home. If you will be on

vacation or not using your dryer for an extended period of time, you

should:

1. Unplug dryer or disconnect power.

2. If you have a gas dryer, close shutoff valve in gas supply line.

3. Clean lint screen. See "Cleaning the I_int Screen."

For dlrect-wlred dryers:

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

I. Disconnect power.

2. Disconnect wiring.

3. Make sure leveling legs are secure in dryer base.

4. Use masking tape to secure dryer door.

Moving care - Gas Dryers

1. Unplug the power supply cord.

2. Close shutoff valve in gas supply line.

3. Disconnect gas supply line pipe and remove fittings attached to

dryer pipe.

4. Cap the open fuel supply line.

5. Make sure leveling legs are secure in dryer base.

6. Use masking tape to secure dryer door.

Unplug dryer or disconnect power.

Open the dryer door. Locate the light bulb cover on the back

wall of the dryer. Using a Phillips head screw driver, remove

the screw located in the lower right-hand corner of the cover.

Remove the cover.

For power supply cord-connected dryers:

1. Unplug the power supply cord.

2. Make sure leveling legs are secure in dryer base.

3. Use masking tape to secure dryer door.

Turn bulb counterclockwise. Replace the bulb with

a l O-watt appliance bulb only. Replace the cover and secure

with the screw.

4. Plug in dryer or reconnect power.

TROUBLESHOOTING

First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)

to possibly avoid the cost of a service ca[[...

in U.S.A. http://www.whidpool.com/he[p - in Canada www.whirlpookca

:::::::::::::::::::::::::::::::::::::::::::::::::

Dryer will not run

Has a household fuse b[own, or has a circuit breaker tripped?

Electric dryers use2 household fuses or circuit breakers. The

drum may be turning, but you may not have heat. Replace the

fuse or reset the circuit breaker. If the problem continues, call

an electrician.

[]

Is the correct power supply available?

Electric dryers require 240-volt power supply. Check with a

qualified electrician.

Was a regular fused used?

Use a time-delay fuse.

Is the dryer door firmly closed?

Was the Start button or knob firmly pressed?

Is a cycle selected?

The dryer will not start in tJ_eWrinkle Prevent position. Move

tile dial past OFF.

No heat

[] Has a household fuse blown, or has a circuit breaker tripped?

Electric dryers use 2 household fuses or circuit breakers. The

drum may be turning, but you may not have heat. Replace the

fuse or reset the circuit breaker. If the problem continues, ca[[

an electrician.

[] For gas dryers, is the valve open on the supply line?

Unusual sounds

[] Has the dryer had a period of non-use?

If the dryer hasn't been used for awhile, there may be a

thumping sound during the first few minutes of operation.

[]

is coin, button, or paper clip caught between the drum and

front or rear of the dryer?

Check the front and rear edges of the drum for small objects.

Clean out pockets before laundering.

is it a gas dryer?

The gas valve clicking is a normal operating sound.

Are the four legs installed, and is the dryer level front to back

and side to side?

The dryer may vibrate if not properly installed. See the

Installation Instructions.

[] Is the clothing knotted or balled up?

When balled up, the load will bounce, causing the dryer to

vibrate. Separate the load items and restart

the dryer.

Timer does not noticeably advance

[] Is the dryer set to Timed or Air Dry?

The timer moves slowly and continuously for the timed setting.

[] Is the dryer set to Automatic Drying?

The timer moves only when the clothing is mostly dry.

Clothes are not drying satisfactorily or drying times are

too long

[] Is the tint screen clogged with lint?

Lint screen should be cleaned before each load.

[]

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to follow these instructions can result in death

or fire.

Is the exhaust vent or outside exhaust hood clogged with lint,

restricting air movement?

Run the dryer for 5-10 minutes. Hold your hand under the

outside exhaust hood to check air movement. If you do not fee[

air movement, dean exhaust system

of lint or replace exhaust vent with heavy metal or flexible

metal vent. See the Installation Instructions.

Are fabric softener sheets blocking the grille?

Use only one fabric softener sheet, and use it only once.

Is the exhaust vent the correct length?

Check that the exhaust vent is not too long or has too many

turns. Long venting will increase drying times. See the

Installation Instructions.

Is the exhaust vent diameter the correct size?

Use 4" (102 mm) diameter vent material

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Place dryer at least 18 inches (460 ram) above the floor

for a garage installation.

Failure to do so can resu[t in death, exp[osion, or fire.

[]

is the dryer located in a room with temperature be[ow

45°F (7°C)?

Proper operation of dryer cycles requires temperatures

above 45°F (7°C).

[]

Isthe dryer located in a doset?

Closet doors must have ventilation openings at the top and

bottom of the door. Sides and front of dryer require a minimum

of 1" (25 ram) of airspace, and the rear of the dryer requires

5" (127 ram). See the Installation Instructions.

Has an air dry cycle been selected?

Select the right cycle for the types of garments being dried.

Is the load too large and heavy to dry quickly?

Separate the load to tumble freely.

Odors

[] Have you recently been painting, staining, or

varnishing in the area where your dryer is located?

If so, ventilate the area. When the odors or fumes are gone

from the area, rewash, and dry the clothing.

[] Is the electric dryer being used for the first time?

The new electric heating element may have an odor. The odor

will be gone after the first cycle.

Cycle time too short Load istoo hot

Excessive Weight Hazard

Use two or more people to move and install dryer.

Failure to do so can result in back or other injury.

[] Is the automatic cycle ending early?

The load may not be contacting the sensor strips. I.eve[

the dryer.

Change the dryness level setting on Automatic Cycles.

Increasing or decreasing the dryness [eve[ will change

the amount of drying time in a cycle.

Lint on load

[] Is the lint screen clogged?

Lint screen should be cleaned before each load.

Stains on load or drum

[] Was the dryer fabric softener properly used?

Add dryer fabric softener sheets at the beginning of the cycle.

Fabric softener sheets added to a partially dried load can stain

your garments.

[] Drum stains are caused by dyes in clothing (usually blue jeans).

This will not transfer to other clothing.

Loads are wrinkled

[] Was the load removed from dryer at the end of

the cycle?

[]

Were laundry items removed from the dryer before the end

of the cycle?

Allow the Coo[ Down cycle to finish before removing laundry

from dryer. All cycles are cooled slowly to reduced wrinkling

and make it easier to handle. Items removed before Coo[ Down

may fee[ very warm.

[]

Was a high temperature cycle used, or was a separate

temperature control set on high?

Select a lower temperature, and use an automatic drying cycle.

These cycles sense the temperature or the moisture [eve[ in the

load and shut off when the load reaches the selected dryness.

This reduces overdrying.

Enhance your dryer with these premium accessories.

For more high-quality items or to order, call 1-800-901-2042,

or visit us at www.applianceaccessories.com. [n Canada, ca[[

1-800-807-6777 or visit us at www.whirlpoolparts.ca.

3404351 Drying rack - fits 29" (737 mm) Super Capacity,

6.5 cu. ft. (0.18 cu. m) - side swing or hamper

door

3406839 Drying rack - fits 29" (737 mm) Su_er Capacity

Plus, 7.0 cu. ft. (0.20 cu. m) - side swing door

only

[] Was the dryer overloaded?

Dry smaller loads that can tumble freely.

LIMITED WARRANTY

For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or

furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter "Whirlpool") will pay for factory specified parts and

repair labor to correct defects in materials or workmanship that existed when this major appliance was purchased. Service must be

provided by a Whirlpool designated service company. YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY

SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. This limited warranty is valid only in the United States or Canada and applies

only when the major appliance is used in the country in which it was purchased. Proof of original purchase date is required to obtain

service under this limited warranty.

ITEMS EXCLUDED FROM WARRANTY

This limited warranty does not cover:

1. Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is

used in a manner that is inconsistent to published user or operator instructions and/or installation instructions.

2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or

repair house fuses, or to correct house wiring or plumbing.

3. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty

coverage.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of products not approved by Whirlpool.

5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage

results from defects in materials or workmanship and is reported to Whirlpool within 30 days from the date of purchase.

6. Pick up and delivery. This major appliance is intended to be repaired in your home.

7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

8. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an

authorized Whirlpool servicer is not available.

9. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance

with Whirlpool's published installation instructions.

10. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered, or

cannot be easily determined.

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR

A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces

do not allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This

warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIRAS PROVIDED HEREIN.

WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow

the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This

warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.

If outside the 50 United States and Canada, contact your authorized Crosley®dealer to determine if another warranty applies.

If you think you need repair service, first see the "Troubleshooting" section of the Use & Care Guide. If you are unable to resolve the

problem after checking "Troubleshooting," additional help can be found by checking the "Assistance or Service" section or by calling

Whirlpool. In the U.S.A., call 1-800-253-1301. In Canada, call 1-800-807-6777. 9/08

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your major appliance

to better help you obtain assistance or service if you ever need it.

You will need to know your complete model number and serial

number. You can find this information on the model and serial

number label located on the product.

Dealer name

Address

Phone number

Model number

Serial number

Purchase date

P P P

SECURITE DE LA SECHEUSE

Votre s_curit_ et celle des autres est tr_s importante.

Nous donnons de nombreux messages de s6curit6 importants dans ce manuel et sur votre appareil m6nager. Assurez-vous de

toujours life tous les messages de s6curit6 et de vous y conformer.

Voici le symbole d'alerte de s6curit6.

Ce symbole d'alerte de s6curit6 vous signale les dangers potentiels de d6ces et de blessures graves a vous

eta d'autres.

Tousles messages de s6curit6 suivront le symbole d'alerte de s6curit6 et le mot "DANGER" ou

"AVERTISSEMENT". Ces mots signifient :

Risque possible de d_c6s ou de blessure grave si vous ne

suivez pas imm6diatement les instructions.

Risque possible de d_c6s ou de blessure grave si vous

ne suivez pas les instructions.

Tousles messages de s6curit6 vous diront quel est le danger potentiel et vous disent comment r6duire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

AVERTISSEMENT

" "Risque d'incendie"

L'installation de la s_cheuse & linge dolt _tre effectu_e par un installateur qualifi_.

installer la s_cheuse conforrn_rnent aux instructions du fabricant et au× codes Iocau×.

Ne pas installer de s_cheuse & linge avec des mat_riau× d'_vacuation en plastique

souple. Si un conduit m_tallique souple (de type papier d'aluminiurn) est installS,

celui-ci dolt _tre d'un type sp_cifique identifi_ par le fabricant de I'appareil et

convenir & une utilisation avec les s_cheuses & linge. Les rnat_riau× d'_vacuation

souples sont connus pour s'affaisser, _tre facilernent _cras_s et bloquer la charpie.

Ces situations obstrueront le d_bit d'air de la s_cheuse & linge et augmenteront le

risque d'incendie.

Pour r6duire le risque de blessure grave ou de d6ces, suivre toutes

les instructions d'installation.

- Conserver ces instructions.

IMPORTANTES INSTRUCTIONS DE St_CURITt_

AVERTiSSEMENT • Pour r6duire le risque d'incendie, de choc 61ectrique ou de blessure Iors de I'utilisation de

la s6cheuse, il convient d'observer certaines pr6cautions 616mentaires dont les suivantes :

[] Lire toutes les instructions avant d'utiliser la s6cheuse.

[] Ne pas placer des articles expos6s aux huiles de cuisson

dans votre s6cheuse. Les articles contamin6s par des

huiles de cuisson peuvent contribuer & une r6action

chimique qui pourrait causer & la charge de s'enflammer.

[] Ne pas faire s6cher dans la machine des articles qui ont

d6j& 6t6 nettoy6s, lav6s, imbib6s, ou tach6s d'essence,

de solvants pour nettoyage & sec, d'autres substances

inflammables, ou de substances explosives puisqu'elles

d6gagent des vapeurs qui peuvent provoquer un

incendie ou une explosion.

[] Ne pas permettre a des enfants de jouer sur ou

I'int6rieur de la s6cheuse. Une surveillance 6troite est

n6cessaire Iorsque la s6cheuse est utilis6e pres d'eux.

[] Avant d'enlever la s6cheuse du service ou la jeter, enlever

la porte du compartiment de s6chage.

[] Ne pas mettre la main dans la s6cheuse si le tambour est

en mouvement.

[] Ne pas installer ni entreposer la s6cheuse ou elle sera

expos6e aux intemp6ries.

[] Ne pas jouer avec les commandes.

[] Ne pas r6parer ni remplacer une piece de la s6cheuse ou

essayer d'en faire I'entretien a moins d'une recommandation

sp6cifique dans le guide d'utlilisation et d'entretien, ou

publi6e dans les instructions de r6paration par I'utilisateur

que vous comprenez et pouvez ex6cuter avec comp6tence.

[] Ne pas utiliser un produit assouplissant de tissu ou des

produits pour 61iminer la statique a moins qu'ils ne soient

recommand6s par le fabricant du produit assouplissant de

tissu ou du produit.

[] Ne pas utiliser la chaleur pour faire s6cher des articles

fabriqu6s avec du caoutchouc mousse ou des mat6riaux

semblables.

[] Nettoyer le filtre a charpie avant et apres chaque charge.

[] Ne pas laisser la charpie, la poussiere, ou la salet6

s'accumuler autour du systeme d'6vacuation ou autour de

I'appareil.

[] Un nettoyage p6riodique de I'int6rieur de la s6cheuse et du

conduit d'6vacuation doit 6tre effectu6 par une personne

qualifi6e.

[] Voir les instructions d'installation pour les exigences de

liaison de I'appareil a la terre.

CONSERVEZ CES INSTRUCTIONS

IMPORTANT : L'installation du gaz doit se conformer aux codes Iocaux, ou en I'absence de codes Iocaux, au National Fuel Gas

Code, ANSI Z223.1/NFPA 54.

La s6cheuse doit 6tre 61ectriquement reli6e & la terre conform6ment aux codes Iocaux, ou en I'absence de codes Iocaux, au Code

canadien de 1'61ectricit6, ANSI/NFPA 70.

Avertissements de la proposition 65 de I'Fttat de Californie "

AVERTISSEMENT " Ce produit contient un produit chimique connu par I'Fttat de Californie pour 6tre a I'origine de cancers.

AVERTISSEMENT " Ce produit contient un produit chimique connu par I'Fttat de Californie pour 6tre a I'origine de malformations

et autres d6ficiences de naissance.

AVERTISSEMENT : Pour votre s_curit_, les renseignements dans ce manuel doivent

_tre observes pour r_duire au minimum les risques d'incendie ou d'explosion ou pour

eviter des dommages au produit, des blessures ou un deces.

- Ne pas entreposer ou utiliser de I'essence ou d'autres vapeurs ou liquides

inflammables b proximit_ de cet appareil ou de tout autre appareil _lectromenager.

-QUE FAIRE DANS LE CAS D'UNE ODEUR DE GAZ :

o Ne pas tenter d'allumer un appareil.

= Ne pas toucher a un commutateur 61ectrique; ne pas utiliser le t616phone se trouvant

sur les lieux.

• Evacuer tousles gens de la piece, de I'_difice ou du quartier.

®Appeler imm_diatement le fournisseur de gaz du t_l_phone d'un voisin. Suivre ses

instructions.

= A d_faut de joindre votre fournisseur de gaz, appeler les pompiers.

- L'installation et I'entretien doivent _tre effectu_s par un installateur qualifi_, une

agence de service ou le fournisseur de gaz.

AVERTISSEMENT : L'odorat ne permet pas toujours la detection d'une fuite de gaz.

Les distributeurs de gaz recommandent I'emploi d'un detecteur de gaz (homologation UL ou CSA).

Pour d'autre information, contacter le fournisseur de gaz local.

En cas de detection d'une fuite de gaz, executer les instructions "Que faire dans le cas d'une odeur de gaz".

'_,',iiiiii,o___i_i_i_iiiiiii:_i_i__¸_'_ii_!!!!i,,iiilii_ii!!,!,_¸,_i:::iii_,:i_i_i_i_ii:;:iii_i_ii'_:i:_ii'i:_iiiiiiiiiii:,_i:::iii"",_,_ii!!!!i¸v,_i!__i:::_ii'i:_i_ii!i_!i!i:iiiio __i_i_i_

Pour s6cher [e [inge avec efficacit6, [es s6cheuses ufilisent [a

cha[eur, mais une bonne ventilation est 6ga[ement n6cessaire.

Un circuit d'6vacuafion ad6quat r6duit [es dur6es de s6chage et

[a consommafion d'6nergie. Voir [es Instructions d'insta[[afion.

Le circuit d'6vacuafion fix6 _ [a s6cheuse joue un r6[e important

dans [a bonne circulation de ['air.

Risque d'incendie

Utiliser un conduit d'_vacuation en m_tal Iourd.

Ne pas utiliser un conduit d'_vacuation en plastique.

Ne pas utiliser un conduit d'_vacuation en feuille

de m_tal.

Le non-respect de ces instructions peut causer

un d_c?_s ou un incendie.

Les visites de service dues _ un circuit d'6vacuafion non appropri_

ne sont pas couvertes par [a garanfie et seront au frais du client,

que[[e que soit [a personne qui a install6 [a s6cheuse.

Pour ma[nten[r une bonne venti[ation :

[] Nettoyer [e fi[tre _ charpie avant chaque charge.

[] Remp[acer [e conduit d'6vacuafion en p[asfique ou a[uminium

par un conduit d'6vacuafion [ourd et rigide de 4" (102 mm)

de diam_tre.

[] Ufi[iser [a [ongueur de conduit [a plus courte possible.

[] Ne pas ufi[iser plus de quatre coudes _ 90° dans un circuit

d'6vacuafion, chaque p[i et courbe r6duit [a ventilation.

Bon Meilleur

[] Retirer [a charpie et [es r6sidus du c[apet d'6vacuation.

[] Retirer [a charpie de ['ensemble du circuit d'6vacuation

au moins tous[es deux ans. Une fois [e nettoyage achev6,

s'assurer de suivre [es Instructions d'insta[[ation fournies avec

[a s6cheuse pour un contr6[e final de ['apparel[.

[] En[ever tout article qui se trouverait devant [a s6cheuse.

TABLEAU DE COMMANDE

off ._a_y Timed Dry

r 7O 60

Wrinkle Prevent 50

Cool Down Damp Dry

Less Dry 20

Energy p_efer ed '_ Cool Down

Automat c Setting Off

Very Dry 30

Automatic off lO

Dry Air Dry

End of Cycle Signal

_ediu_p

Temperature Push to Start

f_bf_c

Cool

Automatic L_,, _'_ so Timed Dry

DrY Dry/ _. High Heat

Higi_'Heat Very_ 40

Dry 30

Off_ 20

Cool

Less Down

Dry off

EnergyPreNrred_

A_or4aticSet_ng Very

Automatic off Air Dry

Dry

Low Heat

Push to Start

Toutes [es caract6ristiques et options ne sont pas disponibles sur tous[es mod6les.

I.'apparence peut diff6rer.

Automatic Dry!Auto Sense Dry (s6chage automatique/

s6chage par d_tection automatlque)

I.e programme de s6chage automatique supprime [a n6cessit6 de

ca[cu[er [a dur6e de s6chage et apporte davantage de soin aux

v6tements. I_eprogramme de s6chage automatique peut 6tre uti[is6

pour [a p[upart des charges.

I_a commande de s6[ection de programme (minuterie) peut 6tre

r6g[6e _ ENERGY PREFERRED (6conergique), ce qui convient

[a p[upart des tissus. A [a fin du programme, vous pouvez v6rifier

[e degr6 de s6chage de [a charge.

[] Si [a charge est plus sbche que vous [e d6sirez, vous pouvez

s6[ectionner un r6g[age plus pr6s de Less Dry (moins sec) [a

prochaine fois que vous s6chez une charge semb[ab[e.

[] Si [a charge est moins s6che que d6sir6, s6[ectionner un

programme minut6 pour terminer [e s6chage. I_ors du prochain

s6chage d'une charge simi[aire, choisir un r6g[age plus proche

de Very Dry (tr6s sec).

I.e tem3s de s6chage avec un 3rogramme automatique varie se[on

[e type de tissu, [a tai[[e de [a charge et [e r6g[age de [a temp6rature.

Sur certains modb[es, [a temp6rature est inc[use dans [es s6[ections

de programme.

R6giage WRINKLE PREVENT antifrolssement

(sur certains mod?_[es)

[.a caract6ristique WRINKI_E PREVENT(antifroissement) se met en

marche h [a fin du programme de s6chage. E[[e d6marre et arr6te

[a s6cheuse p6riodiquement, faisant cu[buter [a charge sans cha[eur

pour 6viter [e froissement.

Sur certains mod6les, WRINKI_E PREVENT (antifroissement) se met

en marche automatiquement & [a fin du programme. I_'ouverture de

[a 3orte arr6te cette caract6ristique. Sur d'autres mod6les, [e bouton

s6 ecteur WRINKI.E PREVENT (antifroissement) peut 6tre r6g 6 _ ON

(marche).

REMARQUE :Un signal est 6mis p6riodiquement [orsque [e

r6g[age WRINKI_E PREVENT (antifroissement) est s6[ectionn6,

mais seu[ement si [e signal de fin de programme est 6ga[ement

s6[ectionn6.

Timed Dry (S6chage minut6)

Sur certains modb[es, [a temp6rature est inc[use dans [es

s6[ections de programme. Sur [es modb[es dot(!s d'un s6[ecteur

de temp6rature, choisir un r6g[age en fonction des tissus dans

[a charge. [.a dur6e de s6chage et [a temp6rature d6pendront du

modb[e de [a s6cheuse.

{5:

Vous pouvez s6[ectionner une temp6rature de s6chage en fonction

des tissus dans votre charge. Si vous 6prouvez une incertitude

['6gard du choix d'une temp6rature pour une charge, choisir [e

r6glage plus bas plu6t que [e r6glage plus 61ev6.

Consei[s de temp6rature

Si votre s6cheuse est munie de p[usieurs r6g[ages de cha[eur :

[] Un r6g[age de cha[eur 6[ev6e 3eut 6tre uti[is6 pour s6cher [es

articles [ourds te[s que es serviettes et es v6tements de travai.

[] Uti[iser un r6g[age de cha[eur faib[e & moyenne 3our s6cher

[es articles moyennement [ourds te[s que draps, chemisiers,

robes, sous-v6tements, tissus de pressage permanent, lingerie

et certains tricots.

[] Vous 3ouvez uti[iser un r6g[age sans cha[eur (& ['air) pour [e

caoutchouc, e p astique ou es tissus sensib[es _ [a cha[eur.

[] S6cher sur une corde _ [inge [es tissus doub[6s ou superpos6s.

REMARQUE : Si vous avez des questions au sujet des temp6ratures

de s6chage pour diverses charges, consulter [es directives sur

['6tiquette du produit.

I_e signal de fin de programme retentit _ [a fin d'un programme.

Sur certains mod6les, [e signal de fin de programme est fixe. Sur

d'autres mod6les, [e signarde fin de _rogramme est s6lectionnable

et ne retentira que s'il est r6g16 _ On (marc-he).

Si [e r6g[age WRINKI_E PREVENT (antifroissement) est s6lectionn6

et quele signal de fin de programme est activ6, [e signal se fait

entendre toutes [es quelques minutes. I_esignal s'arr@e [orsqu'on

ouvre [a porte ou [orsqu'on tourne [e bouton de commande du

programme _ Off (arr6t).

GUIDE DES PROGRAMMES

Tous[es programmes et r6glages ne sont pas disponibles sur tous [es mod?_les.

une commande S6par_e.

Automatic Dry

High Heat

(s6chage automatique

- chaleur 6[ev6e)

Automatic Dry

Low Heat

(s6chage automatique

- chaleur basse)

Serviettes

Very Dry

(tr_s sec)

*Energy Preferred

Automatic Setting

(6co6nergique -

r6glage automatique)

Perm Press

(pressage permanent)

Less Dry (moins sec)

Jeans, v&tements de travail

6pais, serviettes

Tout-aller, chemises, pantalons,

articles [6gers

Serviettes, couvre-mate[as,

6dredons

Jeans, v&tements

de travail 6pals

I_aplupart des charges

Articles synth6tiques de 3oids

moyen ou [6gers, tissus

3ressage 3ermanent, articles

qu ne n6cess tent pas de

repassage.

[.a p[upart des charges

Fournit [e moil[our s6chage dans los plus courts d6[ais.

La dur6e de s6chage varie solon [a tai[[e de [a charge,

[e type de tissu et [e r6g[age du degr6 de s6chage.

Fournit [e moil[our s6chage dans los plus courts d6[ais.

La dur6e de s6chage varie solon [a tai[[e de [a charge,

[e type de tissu et [e r6g[age du degr6 de s6chage.

S?_cheparfaitement los articles trbs [ourds.

Ce degr6 de s6chage 6[imine plus d'humidit6 de [a charge

que [e programme Energy Preferred (6co6nergique).

Sbche los coutures 6paisses.

Uti[iser ce degr6 de s6chage comme point

de commencement du s6chage automatique.

S6che _ fond [es tissus _ pressage permanent et [es

mdlanges synthdtiques.

Ce degr6 de sdchage 6limine moins I'humidit6 que le

_rogramme Energy Preferred (6co6nergique). Los coutures

des v6tements _euvent 6tre [6g6rement humides. A.

ut [ ser pour los charges dont on souha te comp[dter [e

sdchage sur un cintre.

High (6lev6e)

I_ow (basse)

High (6lev6e)

N'iml?orte

[aque[[e

N'iml?orte

[aque[[e

I_ow (basse)

N'importe

[aque[[e

RI_GLAGES SPI_C[AU× Cos r6glages sont ajout6s _ la fin de Certains programmes pour r6duire le froissement.

Cool Down N'importe qu'elle charge C'est [a derni_re 6tape des programmes qui utilisent Absence de

(refroidissement) [a cha[eur. La charge est [entement refroidie pour r6duire cha[eur

[e froissement et en faci[iter sa manipulation.

Wrinkle Prevent N'importe quelle charge Apr_s [a fin d'un programme, [a charge est culbut6e Absence de

(antifroissement) _ intervalles pour 5viter [es plis jusqu'_ ce qu'on [a retire, chaleur

Petites charges, articles [6ger

Articles [ourds ou vo[umineux

te[s que serviettes 6paisses

ou peignoirs

N'importe que[[e charge

N'importe quelle charge

Caoutchouc, plastique, tissus

sensibles _ [a chaleur

Termine [e s6chage si los articles sont encore humides.

S&che en douceur los articles d6[icats et los tricots.

S6che uniform6ment los charges volumineuses ou

Iourdes.

S6che los articles _ un degr6 d'humidit6 ou los articles qui

ne n6cessitent pas un programme de s6chage comp[et.

Aide h a_lanir los faux plis des articles tels que los

v6tements qui ont s6journ6 dans une valise ou qui sont

rest6s trop [ongtemps dans [a s6cheuse.

S6chage sans chaleur.

High (6lev6e)

I_ow (basse)

High (6lev6e)

N'importe

[aque[[e

Cha[eur basso

OU moyenne

solon los tissus

de [a charge

Absence de

cha[eur

AIR DRY

(sdchage & Fair) ou

NO HEAT FLUFF

(duvetage sans

chaleur)

DAMP DRY

(s_chage humide)

Wrinkle Free

(antifroissement)

Timed Dry High Heat

(s6chage minut6 -

chaleur 6lev6e)

Timed Dry High Heat

(s6chage minut6 -

chaleur basse)

Heavy Dry

(s6chage intense)

Articles tr6s [ourds

ou volumineux

TIMED DRY Fairfoncii0nner !a S6cheuse p(iur ie iei_ps indiqu_ Sui [a c-0nimande I

(s6chage minute) Solon le m0d_lel la tei_ p6,iatuie pout 6tre S_!ectionn_e SUi !e bout0n des pr0grammeS 0U6tre

une commando s(_par(!e.

UT{LISAT{ON DE LA SECHEUSE

JV_iiiii:!ii,_,_i:!_:__ii!!_iiii__li_?_i_iiigi:::iiiii_!!!___i:::!!i!i_::!,!_il_?_ii!ii_,_ii!!i(::iiiii_/i!!!_iii:_iiiI%!!_

Risque d'explosion

Garder les matii_res et les vapeurs inflammables, telle

que I'essence, loin de la s6cheuse.

Ne pas faire s6cher un artic{e qui a d6j_ 6t6 touch6 par

un produit inf}ammable (m_me aprils un lavage).

Le non=respect de ces instructions peut causer

un d_c6s, une explosion ou un incendie.

AVERT{SSEMENT : Pour rdduire [e risque d'incendie, de choc

6[ectrique ou de b[essures corp.ore[[es, [ire [es IMPORTANTES

INSTRUCTIONS DE SECURITE avant de faire fonctionner cet

apparel[.

Ce manuel couvre plusieurs mod6les diff6rents. Votre mod?_le peut

ne pas avoir tous[es programmes ou caract6ristiques d6crits.

Avant d'uti[iser [a sdcheuse, essuyer [e tambour de [a sdcheuse avec

un [inge humide pour en[ever [a poussiP_re accumu[de au cours de

['entreposage et de ['expddition.

1. Nettoyer [e filtre h charpie avant chaque charge. Voir

"Nettoyage du filtre h charpie".

2. Charger [es v6tements sans [es tasser dans [a sdcheuse et fermer

la porte. Ne pas surcharger la sdcheuse. Pour de meilleurs

rdsultats, prdvoir suffisamment d'espace pour que [es v6tements

puissent culbuter [ibrement.

3. Tourner le bouton de commande de programme au programme

recommand6 pour le type de charge que vous sdchez. Utiliser

le rdglage automatique Energy Preferred (6conergique) pour

sdcher [a plupart des tissus [ourds et de poids moyen.

4. Si votre sdcheuse poss6de un sdlecteur de tempdrature, [e

rdgler _ [a position recommandde pour [e type de tissu

sdcher. Voir "Descriptions des programmes de [a sdcheuse"

pour des suggestions sur [a tempdrature. Sur certains mod?_les,

[a tempdrature fair partie des sdlections de programme.

5. (OPTION) Votre sdcheuse peut 6tre munie d'un sdlecteur pour

[a caractdristique Wrinkle Prevent (antifroissement). Utiliser

cette caractdristique pour 6viter [e froissement [orsque [a

charge ne peut 6tre retirde de [a sdcheuse d?_sson arr6t.

6. (OPTION) Votre sdcheuse peut 6tre munie d'un End of Cycle

Signal (signal de fin de programme). Le signal est utile Iorsque

vous faites sdcher des articles qui doivent 6tre enlevds de [a

sdcheuse aussit6t qu'elle s'arr6te.

[.e signal de fin de programme fair partie du bouton de mise

en marche et peut &tre sdlectionnd. Tourner [e bouton Start

(mise en marche) _ ON (marche) ou OFF (arr6t). Le signal sera

entendu seulement si[e bouton sdlecteur est rdg16 _ ON.

7. Ajouter une feui[[e d'assoup[issant de tissus, si d6sir6. Suivre

[es instructions sur ['emba[[age.

8. Appuyer sur [a touche Start (mise en marche).

Risque d'incendie

Aucune laveuse ne peut compi_tement eniever I'huiie.

Ne pas faire s6cher des articles qui ont 6t6 salis par

tout genre d'hui{e (y compris les hui{es de cuisson}.

Les articles contenant de la mousse, du caoutchouc

ou du p{astique doivent _tre s6ch6s sur une corde

{inge ou avec le programme de s6chage _ I'air ou

le programme de s6chage sans chaleur.

Le non-respect de ces instructions peut causer

un d6ci_s ou un incendie.

Arr6t et remise en marche

On peut arr6ter [a s6cheuse h tout moment au cours d'un

programme.

Pour arr_ter la s_cheuse

Ouvrir [a porte de [a s6cheuse ou tourner [e bouton de commande

de programme _ OFF (arr6t).

REMARQUE : Le bouton de commande de programme dolt pointer

vers une zone d'arr6t Off quand [a s6cheuse n'est pas uti[is6e.

Pour remettre [a s_cheuse en marche

Fermer [a porte. Choisir un nouveau programme et une nouve[[e

temp6rature (si d6sir6). Appuyer sur [a touche Start.

c , d

Uti[iser [a grille de s6chage [_our s6cher sans cu[butage [es articles

te[s que [es chandai[s et orei[[ers. [.e tambour tourne, mais [a grille

de s6chage ne bouge pas.

Si votre mod6le n'a pas de grille de sdchage, vous pouvez en

acheter une. Pour savoir si votre mod?4[e permet ['uti[isation d'une

grille de sdchage de sdchage et pour obtenir des informations sur [es

commandes, veui[[ez consulter [a premi?4re page de votre manuel

ou contacter [e vendeur chez qui vous avez achet6 votre sdcheuse.

REMARQUE : La grille de sdchage dolt 6tre enlevde pour [e

cu[butage normal.

UtH[sation de [a grille de s_chage

1. Placer [a grille de sdchage dans [a sdcheuse.

G[isser [es chevi[[es h ['arri6re dans [es a[vdo[es sur [a paroi

arri?4re de [a sdcheuse. Abaisser [es plods _ ['avant pour qu'i[s

reposent sur ['ouverture de [a sdcheuse.

2. Placer [es articles moui[[ds sur [a grille de sdchage. Laisser

de ['espace entre [es articles. Ne pas [aisser d'artic[es pendre

par-dessus [e bord de [a grille. Fermer [a porte.

Sdlectionner un programme de s6chage minut6 et une

tempdrature ou un programme de sdchage b_['air. J.es articles

contenant mousse, caoutchouc ou piastique doivent 6tre

sdchds sur une corde _ linge ou par le programme de sdchage

['air. Se r6fdrer au tableau suivant.

Mettre la s6cheuse en marche. R6gler de nouveau [e

programme pour terminer [e s6chage, si n6cessaire.

Jouets rembourr6s ou S6chage Basso 60 min.

orei[[ers (garnis de coton minut6

ou de polyester)

Jouets rembourr6s ou Air N/A 90 min.

orei[[ers (rembourrage (sans

en caoutchouc mousse) cha[eur)

ENTRETIEN DE LA SECHEUSE

Eviter de [aisser des 6[6ments qui pourraient obstruer [e d6bit de

combustion et emp6cher une bonne ventilation autour de

[a s6cheuse. Ce qui imp[ique d'en[ever los piles de lingo situ6es

devant [a s6cheuse.

Risque d'expiosion

Garder [es mati_res et les vapeurs inflammables, telle

que I'essence, loin de la s6cheuse.

Placer [a s6cheuse au moins 460 mm (18 pc) au=dessus

du plancher pour une installation dans un garage.

Le non=respect de ces instructions peut causer

un d6c_s, une explosion ou un incendie.

Nettoyer [e fi[tre _ charpie avant chaque charge. Un fi[tre obstru6 de

charpie peut augmenter [e temps de sdchage.

iMPORTANT :

[] Ne pas faire fonctionner [a s6cheuse avec un filtre _ charpie

ddplac6, endommag6, bloqu6 ou manquant. Une telle action

pout causer une surchauffe et des dommages _ [a sdcheuse et

aux tissus.

[] Si de [a charpie tombe dans [a sdcheuse au moment du retrait

du filtre, vdrifier [e conduit d'dvacuation et retirer [a charpie. I_e

cla9et d'dvacuation est situ6 [h par o_ ['air de [a sdcheuse sort

de a maison.

Nettoyage avant chaque charge

Style 1 :

1. Le fi[tre _ charpie est situ6 au sommet de [a s6cheuse. Tirer [e

fi[tre _ charpie vers vous. En[ever [a charpie du fi[tre en

[a rou[ant avec los doigts. Ne pas rincer ni [aver [e fi[tre pour

en[ever [a charpie. [.a charpie moui[[6e s'en[bve diffici[ement.

2. Remettre [e filtre _ charpie en [e poussant fermement en place.

Style 2 :

1. [.e fi[tre 5 charpie se trouve dans [a porte de [a s6cheuse. Tirer

[e fi[tre _ charpie vers [e haut. En[ever [a charpie du fi[tre en

[a rou[ant avec los doigts. Ne pas rincer ni [aver [e fi[tre pour

en[ever [a charpie. [.a charpie moui[[6e s'en[6ve diffici[ement.

2. Remettre [e filtre _ charpie en [e poussant fermement en place.

Nettoyage au besoin

1. En[ever [a charpie du fi[tre en [a rou[ant avec los doigts.

Moui[[er los deux c6t6s du fi[tre _ charpie avec de ['eau

chaude.

Mouiller une brosse en nylon avec de ['eau chaude et du

d6tergent [iquide. Frotter [e fi[tre avec [a brosse pour on[ever

['accumulation de r6sidus.

Rincer [e fi[tre _ ['eau chaude.

Bien sdcher [e filtre _ charpie avec une serviette propre.

Replacer le filtre dans la sdcheuse.

i"qei:k: 9,aSediiii<!ii ii iii, ii:66/: ii:, iii iii,¸die iia sdc!:iiu :!! ii:, iiise

Appliquer un nettoyant m6nager ininflammable sur [a zone

tachde du tambour et frotter avec un Jingo doux jusqu'_ ceque

[a tache s'eni6ve.

2. Essuyer compl6tement [e tambour avec un [inge humide.

3. Faire cuibuter une charge de lingo ou de serviettes propres

pour s6cher [e tambour.

REMARQUE : I_es v6tements contenant des teintures instabies,

teis que jeans en denim ou articles en coton de couleur vive,

peuvent d6colorer ['int@ieur de [a s6cheuse. Ces taches ne sont pas

nuisibies _ votre s6cheuse et ne tacheront pas [es v6tements des

charges futures. Faire sdcher los articles avec une teinture instabie

en los tournant _ ['envers pour emp6cher [e transfert de [a teinture.

A I'int6rieur de [a s6cheuse

La charpie devrait 6tre en[ev(_e tous [es 2 ans, ou plus souvent,

se[on ['uti[isation de [a s6cheuse. I_enettoyage devrait 6tre effectu6

par une personne qua[ifi6e.

A ['int6rieur du conduit d'6vacuafion

[.a charpie devrait 6tre en[ev6e tous[es 2 ans, ou plus souvent,

solon ['utilisation de [a sdcheuse.

Entretien avant les vacances

On ne dolt faire fonctionner [a s6cheuse que [orsqu'on est pr6sent

Si ['uti[isateur dolt partir en vacances ou n'uti[ise pas [a s6cheuse

pendant une p6riode prolong6e, i[ convient d'ex6cuter los

op6rations suivantes :

1. D6brancher [a s6cheuse ou d6connecter [a source de courant

6[ectrique.

2. Pour [es s6cheuses _ gaz, former [e robinet d'arr6t de [a

canalisation de gaz.

3. Nettoyer [e filtre _ charpie. Voir "Nettoyage du filtre _ char@e'.

Entrefien avant un d6m_nagement -

S6cheuses 6[ectriques

Pour s6cheuses raccord6es _ un cordon d'alimentation :

1. D6brancher [e cordon d'alimentation.

2. Veiller _ ce que los pieds de nivellement soient fix6s

solidement _ la base de la s6cheuse.

3. Utiliser du ruban adh6sif de masquage pour fixer [a porte de [a

s6cheuse.

Pour s6cheuses avec raccordement direct :

Risque de choc 61ectrique

D6connecter la source de courant 6lectrique avant

I'entretien,

Replacer pi_ces et panneaux avant de faire la remise

en marche,

Le non-respect de ces instructions peut causer

un d6c_s ou un choc 6lectrique,

1. Ddconnecter [a source de courant 6[ectrique.

2. Ddconnecter [e c_blage.

3. S'assurer que [es pieds de nivellement sont solidement fix6s

la base de la sdcheuse.

4. Utiliser du ruban adh6sif de masquage pour fixer [a porte

de la s6cheuse.

1. D6brancher [e cordon d'a[imentation 6[ectrique.

2. Former [e robinet d'arr6t de [a cana[isation de gaz.

3. D6brancher [e tuyau de [a cana[isation de gazet retirer [es

raccords fix6s sur le tuyau de la s6cheuse.

4. Recouvrir [a cana[isation de gaz ouverte.

5. Veil[or _ ce que [es pieds de nive[[ement soient fix6s

solidement _ la base de la s6cheuse.

6. Uti[iser du ruban adh6sif de masquage pour fixer [a porte de

la s6cheuse.

D6brancher [a s6cheuse ou d6connecter [a source de courant

6[ectrique.

Ouvrir la porte de la s6cheuse. Trouver le couvercle de

I'ampoule d'6clairage sur la paroi arri6re de la s6cheuse. A

['aide d'un tournevis Phillips, on[ever [avis situ6e au coin

inf6rieur droit du couverc[e. En[ever [e couverc[e.

Tourner I'ampoule dans le sons antihoraire. Remplacer

['ampoule seulement par une ampoule de 10 watts pour

apparel[ 6[ectrom6nager. R@nstaller [e couvercle et[e fixer

avec la vis.

4. Brancher [a s6cheuse ou reconnecter [a source de courant

6[ectrique.

Page is loading ...

Estate Dryer User Instructions

Brand: Estate

Model: Dryer

Category: Tumble dryers

Type: User Instructions

Download PDF

report

in other languages

français: Estate Dryer

Estate Dryer User Instructions

Estate Dryer User Instructions

in other languages

Related papers

Other documents