BLACK+DECKER KX2000K User manual

Page is loading ...

2

English (Original instructions) 4

Deutsch (Übersetzung der Originalanleitung) 9

Français (Traduction des instructions d'origine) 15

Česky (Přeloženo z původního návodu) 21

Magyar (Fordítás az eredeti kezelési utasítás alapjan készült) 27

Polski (Tłumaczenie oryginalnej instrukcji) 34

Slovenčina (Preložené z pôvodného návodu) 41

Русский язык (Перевод с оригинала инструкции) 47

Українська (Переклад оригінальних інструкцій) 54

Türkçe (Çevirisi orijinal talimatlardan yapılmıştır) 61

Page is loading ...

4

ENGLISH

Intended use

Your Black & Decker heat gun has been designed

for various heating applications such as paint

stripping. This product is intended for consumer

use and indoor use only.

Safety instructions

General safety rules

Warning! Read all safety warnings

and all instructions. Failure to follow all

instructions may result in electric shock,

ﬁ re and/or serious injury.

Save all warnings and instructions for future

reference.

The term “power tool” in all of the warnings listed

below refers to your mains operated (corded)

power tool or battery operated (cordless) power

tool.

1. Work area safety

a. Keep work area clean and well lit. Cluttered

and dark areas invite accidents.

b. Do not operate power tools in explosive

atmospheres, such as in the presence of

ﬂ ammable liquids, gases or dust. Power

tools create sparks which may ignite the dust

or fumes.

c. Keep children and bystanders away while

operating a power tool. Distractions can

cause you to lose control.

2. Electrical safety

a. Power tool plugs must match the outlet.

Never modify the plug in any way. Do not

use any adapter plugs with earthed

(grounded) power tools.

Unmodiﬁ ed plugs and matching outlets will

reduce risk of electric shock.

b. Avoid body contact with earthed or

grounded surfaces such as pipes,

radiators, ranges and refrigerators. There is

an increased risk of electric shock if your body

is earthed or grounded.

c. Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

d. Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the

power tool. Keep cord away from heat, oil,

sharp edges or moving parts. Damaged or

entangled cords increase the risk of electric

shock.

e. When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces

the risk of electric shock.

f. If operating a power tool in a damp location

is unavoidable, use a Residual Current

Device (RCD) protected supply. Use of an

RCD reduces the risk of electric shock.

3. Personal safety

a. Stay alert, watch what you are doing

and use common sense when operating

a power tool. Do not use a power tool while

you are tired or under the inﬂ uence of

drugs, alcohol or medication. A moment of

inattention while operating power tools may

result in serious personal injury.

b.

Use personal protective equipment. Always

wear eye protection. Protective equipment

such as dust mask, non-skid safety shoes, hard

hat, or hearing protection used for appropriate

conditions will reduce personal injuries.

c. Prevent unintentional starting. Ensure

the switch is in the off-position before

connecting to power source and/or battery

pack, picking up or carrying the tool.

Carrying power tools with your ﬁ nger on the

switch or energising power tools that have the

switch on invites accidents.

d. Remove any adjusting key or wrench

before turning the power tool on. A wrench

or a key left attached to a rotating part of the

power tool may result in personal injury.

e. Do not overreach. Keep proper footing

and balance at all times. This enables

better control of the power tool in unexpected

situations.

f. Dress properly. Do not wear loose clothing

or jewellery. Keep your hair, clothing and

gloves away from moving parts. Loose

clothes, jewellery or long hair can be caught in

moving parts.

g. If devices are provided for the connection

of dust extraction and collection facilities,

ensure these are connected and properly

used. Use of these devices can reduce dust

related hazards.

4. Power tool use and care

a. Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at

the rate for which it was designed.

5

ENGLISH

b. Do not use the power tool if the switch

does not turn it on and off. Any power tool

that cannot be controlled with the switch is

dangerous and must be repaired.

c. Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

d. Store idle power tools out of the reach

of children and do not allow persons

unfamiliar with the power tool or these

instructions to operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e. Maintain power tools. Check for

misalignment or binding of moving parts,

breakage of parts and any other condition

that may affect the power tools operation.

If damaged, have the power tool repaired

before use. Many accidents are caused by

poorly maintained power tools.

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to

control.

g. Use the power tool, accessories and

tool bits etc. in accordance with these

instructions, taking into account the

working conditions and the work to

be performed. Use of the power tool for

operations different from those intended could

result in a hazardous situation.

5. Service

a. Have your power tool serviced by

a qualiﬁ ed repair person using only

identical replacement parts. This will make

sure that the safety of the power tool is

maintained.

Additional safety warnings

Warning! Additional safety instructions for

heat guns.

Warning! Do not use outdoors, indoor use only.

Warning! This appliance must be placed on its

stand when not in use.

Warning! A ﬁ re may result if the appliance is not

used with care, therefore be careful when using the

appliance in places where there are combustible

materials.

 Do not apply heat to the same place for a long

time.

 Do not use in presence of an explosive

atmosphere.

 Be aware that heat may be conducted to

combustible materials that are out of sight.

 Place the appliance on its stand after use and

allow it to cool down before storage.

 Do not leave the appliance unattended when it

is switched on.

 Do not obstruct either the air intake slots or the

nozzle outlet as this may cause excessive heat

build up resulting in damage to the appliance.

 Do not direct the hot air ﬂ ow at other people or

animals.

 Do not touch the nozzle as it becomes very

hot during use and remains hot for up to 30

minutes after use.

 Do not place the nozzle against any object

during or immediately after use.

 Do not poke anything down the nozzle as it

could give you an electric shock.

 Do not look down the nozzle while the

appliance is switched on.

 Do not use the appliance as a hair dryer! The

air temperature is far higher than a hardware.

 Ensure adequate ventilation during use as

toxic fumes may be produced.

 Do not use the appliance in a damp

atmosphere.

 When stripping paint, ensure that the

work area is enclosed. Wear a dust mask

speciﬁ cally designed for protection against

lead paint dust and fumes and ensure that

persons within or entering the work area are

also protected.

 Do not burn paint, as it could cause a ﬁ re

hazard.

 Do not allow paint to adhere to the nozzle as it

could ignite after some time.

 Switch off the appliance and allow it to cool

before ﬁ tting any accessory.

Stripping lead-based paint



Extreme care should be taken when stripping

paint. The peelings, residue and vapours of

paint may contain lead, which is poisonous. Any

pre-1960 building may in the past have been

painted with paint containing lead. This paint

may be covered with additional layers of paint.

Once deposited on surfaces, hand to mouth

contact can result in the ingestion of lead.

6

ENGLISH

 Exposures to even low levels of lead can

cause irreversible brain and nervous system

damage. The greatest danger of lead

poisoning is to children and pregnant women.

 Before starting work, it is important to

determine whether the paint to be stripped

contains lead. This can be done using a test kit

or by a professional decorator. Do not smoke,

eat or drink in a work area that could or may

be contaminated by lead. Lead based paints

should only be removed by a professional and

should not be removed using a heat gun.

Safety of others

 This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities, or

lack of experience and knowledge, unless they

have been given supervision or instruction

concerning use of the appliance by a person

responsible for the their safety.

 Children should be supervised to ensure that

they do not play with the appliance.

Labels on tools

Warning! To reduce the risk of injury, the

user must read the instruction manual.

Electrical safety

This product must be earthed. Always

check that the power supply corresponds

to the voltage on the rating plate.

Power plugs must match the outlet. Never modify

the plug in any way. Unmodiﬁ ed plugs and

matching outlets will reduce risk of electric shock.

 If the supply cord is damaged, it must be

replaced by the manufacturer or an authorised

Black & Decker Service Centre in order to

avoid a hazard.

Extension cables & Class 1 product

 A 3-core cable must be used as your appliance

is earthed and of Class 1 construction.

 Up to 30m (100 ft) can be used without loss of

power.

Voltage drops

Inrush currents cause short-time voltage drops.

Under unfavourable power supply conditions, other

equipment may be affected. For example, artiﬁ cial

lighting will show a temporary drop in magnitude

when the machine is switched on. If the system

impedance of the power supply is lower than 0.19

, disturbances are unlikely to occur.

Features

1. On/off switch

2. Heat control knob

3. Nozzle

Assembly

Warning! Before assembly, make sure that the

appliance is switched off and unplugged.

Fitting an accessory

A selected range of accessories can be obtained

from your local retailer.

- Cone nozzle: Concentrates the air stream

on a smaller area.

- Fish tail: Spreads the air stream over

a wider area

- Spoon reﬂ ector: For soldering pipes.

- Glass protector: For the protection of glass

during paint stripping.

- Scraper: For the removal and stripping

paint and varnish.

 Fit the connecting piece of the accessory over

the nozzle (3).

Warning! Make sure that the tool is switched off

and cooled before ﬁ tting any accessory.

Residual risks

Additional residual risks may arise when using the

tool which may not be included in the enclosed

safety warnings. These risks can arise from

misuse, prolonged use etc.

Even with the application of the relevant safety

regulations and the implementation of safety

devices, certain residual risks cannot be avoided.

These include:

 Injuries caused by touching any rotating/

moving parts.

 Injuries caused when changing any parts,

blades or accessories.

 Injuries caused by prolonged use of a tool.

When using any tool for prolonged periods

make sure you take regular breaks.

 Impairment of hearing.

 Health hazards caused by breathing dust

developed when using your tool (example:-

working with wood, especially oak, beech and

MDF).

Use

Warning! Let the tool work at its own pace. Do not

overload.

7

ENGLISH

Setting the temperature (ﬁ g. A)

 To increase the temperature setting, turn the

heat control knob (2) clockwise.

 To reduce the temperature setting, turn the

heat control knob anti-clockwise.

Switching on and off

 To switch the tool on, set the on/off switch (1)

to position I.

 To switch the tool off, set the on/off switch to

position O.

Using the tool

Your tool is ﬁ tted with a thermostat for your safety.

Using the tool continuously for very long periods

or other severe duty cycles may cause the tool

to overheat and stop working. It is therefore

recommended that you allow the tool to cool down

at regular intervals during use.

 Allow the tool to heat up for a few seconds

before use.

 At ﬁ rst use some smoke may emit from the

nozzle. This is normal and will soon decrease.

 Use a low temperature setting for drying paint

and varnish, removing stickers, shrinking

insulation tubes, and thawing frozen pipes.

 Use a medium temperature setting for welding

plastics, bending plastic pipes, and loosening

tight nuts and screws.

 Use a high temperature setting for removing

paints and lacquers, and soldering plumbing

joints.

 If you are unsure about using this tool

on a particular material, start with a low

temperature setting and perform a test on

scrap material.

Hands free use (ﬁ g. B)

The tool has stand locations (4) to facilitate hands

free use.

 Place the tool with the nozzle up on a surface

where it cannot be tipped over.

 Secure the cable to prevent pulling the tool out

of the stand.

Warning! Always point the tool away from yourself

or other persons. Do not touch the nozzle. Take

care that no material drops into the nozzle.

Paint stripping

 Direct the hot air at the working area to heat up

the paint.

 Do not burn the paint. Keep the nozzle at least

25 mm from the surface.

 When the paint softens, remove the paint

using a scraper. Scrape the softened paint

immediately or it will harden again.

 Scrape with the grain of the wood wherever

possible.

 Do not allow paint and debris to collect on the

scraper.

 When scraping from a vertical position, scrape

downwards to prevent the paint from falling

back into the nozzle.

 When stripping paint from a surface next to

glass, take the necessary measures to protect

the glass from the heat.

Warning! Use a glass protector nozzle when

stripping paint from metal or wood framed

windows.

 Dispose of all paint debris safely and make

sure that the work area is thoroughly clean

after use.

Cooling down

During use, the nozzle of the tool becomes

extremely hot. After switching off, leave the tool to

cool down for at least 30 minutes.

 Place the tool with the nozzle up on a surface

where it cannot be tipped over.

 To speed up the cooling time, run the tool on

a low minimum temperature setting for a few

minutes before switching off.

Maintenance

Your Black & Decker appliance has been

designed to operate over a long period of time

with a minimum of maintenance. Continuous

satisfactory operation depends upon proper care

and regular cleaning of the appliance.

Warning! Switch off and unplug the appliance and

allow it to cool down before doing any maintenance

on the appliance.

 Regularly clean the ventilation slots in your

appliance using a soft brush or dry cloth.

 To clean the appliance, use only mild soap

and a damp cloth. Do not use any abrasive or

solvent-based cleaner. Never let any liquid get

inside the appliance and never immerse any

part of the appliance into liquid.

Mains plug replacement (U.K. & Ireland only)

If a new mains plug needs to be ﬁ tted:

 Safely dispose of the old plug.

 Connect the brown lead to the live terminal in

the new plug.

 Connect the blue lead to the neutral terminal.

8

ENGLISH

 Connect the green/yellow lead to the earth

terminal.

Warning! Follow the ﬁ tting instructions supplied

with good quality plugs. Recommended fuse: 13 A.

Protecting the environment

Separate collection. This product must

not be disposed of with normal household

waste.

Should you ﬁ nd one day that your Black & Decker

product needs replacement, or if it is of no further

use to you, do not dispose of it with household

waste. Make this product available for separate

collection.

Separate collection of used products and

packaging allows materials to be recycled

and used again. Reuse of recycled

materials helps prevent environmental

pollution and reduces the demand for raw

materials.

Local regulations may provide for separate

collection of electrical products from the

household, at municipal waste sites or by the

retailer when you purchase a new product.

Black & Decker provides a facility for the collection

and recycling of Black & Decker products once

they have reached the end of their working life. To

take advantage of this service please return your

product to any authorised repair agent who will

collect them on our behalf.

You can check the location of your nearest

authorised repair agent by contacting your local

Black & Decker ofﬁ ce at the address indicated in

this manual. Alternatively, a list of authorised Black

& Decker repair agents and full details of our after-

sales service and contacts are available on the

Internet at: www.2helpU.com.

Technical data

KX2000 TYPE 3

Voltage Vac 230

Construction Class I

Power input W 2000

Temperature range °C 50 - 600

Weight kg 0,85

L

pA

(sound pressure) 75 dB(A) hand/arm weighted

vibration 2.5 m/s

2

Guarantee

Black & Decker is conﬁ dent of the quality of its

products and offers an outstanding guarantee. This

guarantee statement is in addition to and in no way

prejudices your statutory rights. The guarantee is

valid within the territories of the Member States of

the European Union and the European Free Trade

Area.

If a Black & Decker product becomes defective

due to faulty materials, workmanship or lack of

conformity, within 24 months from the date of

purchase, Black & Decker guarantees to replace

defective parts, repair products subjected to

fair wear and tear or replace such products to

make sure of the minimum inconvenience to the

customer unless:

 The product has been used for trade,

professional or hire purposes.

 The product has been subjected to misuse or

neglect.

 The product has sustained damage through

foreign objects, substances or accidents.

 Repairs have been attempted by persons other

than authorised repair agents or Black

& Decker service staff.

To claim on the guarantee, you will need to submit

proof of purchase to the seller or an authorised

repair agent. You can check the location of your

nearest authorised repair agent by contacting

your local Black & Decker ofﬁ ce at the address

indicated in this manual. Alternatively, a list of

authorised Black & Decker repair agents and full

details of our aftersales service and contacts are

available on the Internet at:

www.2helpU.com

Please visit our website www.blackanddecker.

co.uk to register your new Black & Decker product

and to be kept up to date on new products and

special offers. Further information on the Black

& Decker brand and our range of products is

available at www.blackanddecker.co.uk.

Page is loading ...

BLACK+DECKER KX2000K, KX2000 User manual

Related papers

Other documents