OceanAire OWC6012 Owner's manual

OWC6012
OceanAire
Brand
OceanAire
Model
OWC6012
Category
Thermostats
Type
Owner's manual
Micro Air Corporation
FX-Maxx THERMOSTAT
Operations Manual
B
I>'n] AUTO
MODE I>'>" COOL
IMMM'IHEAT
MOISTURE
CONTROL
I FAN] -AUTO
SPEED -MANUAL
Eil II_I I' c na
[POWE1 Sit~T :: ::'RGE [Tn..]1,,1 SETPOINT
OCEANAIRE, INC.
6216 Oakton Street
Morton Grove, IL 60053
PHONE: 847-583-0311
FAX: 847-583-0312
E-MAIL:[email protected]
WEB: www.oceanaire-inc.com
FX-Maxx Operations Manual
CONTENTS
FX-Maxx Operations Manual
Micro Air Corporation
124Route 526
Allentown, NJ 08501
BASICOPERATION....... ... ...... ... 1
OPERATOR CONTROLS AND DISPLAY PANEL 2 & 3
MODES OF OPERATION ... 4
MOISTURECONTROLMODE. ... 4
FANMODES 5
SPECIFICATIONS 6
WIRING DIAGRAMS ...... .... . . ......... .. 7 & 8
Copyright @ 1997 Micro Air Corporation, All Rights Reserved
No part of this publication may be reproduced, translated, stored in a retrieval system, or
transmitted on any form or by means electronic, mechanical, photocopying, recording or
otherwise without prior written consent by Micro Air Corporation.
Every precaution has been taken in the preparation of this manual to insure its accuracy.
However, Micro Air Corporation assumes no responsibility for efforts and omissions. Neither
is any liability assumed for damages resulting from the use of this product and information
contained herein.
Revision: 03 01/02/98
FX-Maxx Operations Manual
BASIC OPERATION
POWER BUTTON Press the power button once to toggle the unit to the on mode. Press the power
button again to toggle the unit to the off mode.
[ FAN ]II1II AUTO
SPEED MANUAL
I' ;,1 10J!IWi1I +;,','1 IF' %'1 191'&I IID>':I1
FAN BUTTON Press and release the fan
button to advance from auto to manual fan.
Press and release to increase the manual fan
speeds, 1 through 6. Press and release again
returns to the auto fan mode. The selected fan
mode is indicated by the Auto and Manual fan
LED's
B
INb':lI] AUTO
MODE ""'"Mi. COOL
I':':II'IIIIHEAT
MOISTURE
CONTROL
B
INI'I;]1:" INSIDE
TEMP
1
1§:@]1'1 DISCHARGE
ELECT
E;9JWI SETPOINT
UP BUTTON Momentarilypress and the set
point will appear in the temperature display.
rwl W I
The set point increases one degree each time
~ ~ the up button is pressed and released.
DOWN BUTTON Momentarily press and release to display the set point. The set point is decreased
one degree each time the down button is pressed and released.
MODE BUTTON The mode button is used to select one of 4 Operating Modes. Press and release to
advance to the next mode. Continue to press and release until the desired Operating Mode is reached.
The mode selected is indicated by the Mode LED.
TEMP SELECT BUTTON Press and release to view inside [return] air temperature, outside
[discharge] air temperature or set point. The appropriate LED will be lit indicating the temperature is dis-
played.
THREE DIGIT DISPLAY The inside [return] temperature is displayed wheneverthe control is turned
on. The display provides a readout of the inside air temperature which is locatedin the supply duct.
HEA T MODE LED The heat mode LED is lit when Heating is selected.
COOL MODE LED The cool mode LED is lit when the Cooling is selected.
AUTO LED The auto LED is lit when the "Automatic Heating or Cooling Modeis selected. The control
will automatically switch to heating or cooling when this mode is selected.
MOISTURE CONTROL LED The moisture LED is lit when the Moisture Control is selected.
MANUAL FAN LED The manual fan LED is lit when a manual fan speeds is selected.
AUTO FAN LED The auto fan LED is lit when automatic fan speed operation is selected.
FAN SPEED BAR GRAPH There are six [6] individual fan speed LED's. Each LED represents one
[1] fan speed. Low fan [1] is indicated by illuminating the first LED. High fan speed is indicated by illu-
minating all six [6] LED's.
COMPRESSOR LED The system operating status [Compressor On or Off] is indicated by turning
On the right most decimal point in the 3 Digit Display.
Revision: 03 01/02/98
Page 1
FX-Maxx Operations Manual
OPERATOR CONTROLS AND DISPLAY PANEL
Refer to figure 1for the buttons locationsand display functions listed on the following pages.
FX-MaxxDisplay Panel
[::Jt:;i AUTO
~ I;:;'" ~~~
7
MOISTURE
CONTROL
[ FAN ] .. AUTO
SPEED tm;"? MANUAL
18
13
14
12
15
1
8
TEMP
ELECT
IIImoo INSIDE
DISCHARGE
I, I SETPOINT ~~
6
16
17
4 3
Figure 1: FX-Maxx ControlButtons and Indicator Displays
1. POWER BUTTON The power button is used to toggle between the on and off modes.
Press the power button once to toggle the unit to the on mode. Press the power button again to
toggle the unit to the off mode.
2. FAN BUTTON Press and release the fan button to advance from auto fan to manual
fan. Press and release the fan button to advance the manual fan speeds, 1 through 6. Press and
release again to return to the automatic fan mode. The selected fan mode is indicated by the
auto and manual fan LED's.
3. UP BUTTON Momentarily press the up button and the set point will appear in the
temperature display. Press and release the up button to increase the set point one degree. The
set point is increased by one degree each time the up button is pressed and released. The high-
est set point allowed is 85° F. The up button is used in conjunction with the down button to dis-
play the outside air temperature whenthe control is on.
4. DOWN BUTTON Momentarily press and release the down button to display the set
point. Press and release the down button to decrease the set point. The set point is decreased
one degree each time the down button is pressed and released. The lowest set point allowed is
55° Fahrenheit. The down button is used in conjunction with the up button to display the out-
side air temperature when the control is on.
Revision: 03 01/02/98
Page 2
10
9
5
8 -
II'
2
FX-Maxx Operations Manual
5. MODE BUTTON The mode button is used to select one of the four operating modes. Press and
release the mode button and the FX-Maxx will advance to the next mode. Continue to press and release the
Mode button until the desired operating mode is reached. The mode selected is indicated by the Mode LED, i.e.,
"
Cool, Heat, Automaticor Moisture Mode.
6. TEMP SELECT BUTTON Press and release the Temp Select Button to view inside air tempera-
ture, discharge air temperature or the set point. The appropriate LED, Inside, Discharge or Set Point will be lit
indicating which temperature is being displayed. If no outside air sensor is installed three [3] dashes will appear
in the Three Digit Display.
7. THREE DIGIT SEVEN SEGMENT DISPLAY The inside air temperature is displayed in the
window whenever the control is turned on. The three digit 7 segment display provides a readout of the inside air
temperature whichis located in the face plate.
The display also indicates fault codes and discharge air temperature when the discharge air sensor is installed.
The display momentarilyindicates the set point when the up or down button is pressed.
When the control resumes operation after a power interruption all the display LEDs will turn on for one second.
This is a normal operating condition and is referred to as "Power On Reset".
8. HEAT MODE LED The heat mode LED will be lit when the Heat Mode has been selected. The heat
mode LED is alsolit whenthe optional electric heat is installed and the heat mode is selected.
9.
COOL MODE LED The cool mode LED will be lit when the Cooling Mode has been selected.
10. AUTO LED The autoLEDislitwhentheautomaticheatingorcoolingmodehasbeenselected. The control
will automaticallyswitchto heating or cooling when this mode is selected.
'\
11. MOISTURE CONTROL LED The moisture mode LED is lit when the Moisture Control has been
selected. This mode is used to control humidity during periods when the temperature is satisfied but humidity is
still high.
12. MANU AL FAN LED The manual fan LED will be lit when one of six manual fan speeds has been
selected.
13. AUTO FAN LED The auto fan LED is illuminated when automatic fan speed operation has been selected.
14. FAN SPEED BAR GRAPH There are six [6] individual fan speed LED's in the Fan Speed Bar
Graph. Each LED represents one [1] fan speed. Low fan speed [1] is indicated by illuminating the first LED.
High fan speed is indicated by illuminating all six [6] LED's. Any of the six [6] fan speeds available are dis-
played by illuminatingthe appropriate LED's.
15.
INSIDE LED The inside LED is lit when the inside air temperature is being displayed.
16.
DISCHARGE LED The discharge LEDis turned on when the discharge temperature is displayed.
17.
SET POINT LED The set point LED is turned on when the set point is displayed.
18. COMPRESSOR LED The system operating status [Compressor On or Offl is indicated by
turning On the right most decimal point in the 3 Digit Display.
'"
Revision: 03 01/02/98
Page 3
FX-Maxx Operations Manual
FAN MODES
Automatic Fan Speeds
FX-Maxx has 6 automatic fan speeds. Speed 6 is high, 3 is medium and 1 is low or the slowest speed,
Automatic fan mode allows the FX-Maxx to determine the required fan speed based on room temperature.
The closer the room temperature is to the set point, the slower the fan will run. This permits a balance be-
tween the most efficient temperature control and slower, quieter fan speeds. Automatic fan operation is
the factory default, however, manual fan speed control is available.
Manual Fan Mode
Six (6) is the fastest and 1represents the slowest speed. Manual fan mode
allows the user to select and maintain the desired fan speed manually.
When a manual fan speed has been selected, the fan speed bar graph
will indicate the speed selected by the number of LED's lit.
Select speed 3, for example, and the first 3 LEDs in the fan bar graph will turn
on. Manual fan is sometimes preferred when room temperature is constantly changing due to varying heat
loads.
FAN SPEEDS
- - _I,W"",'].?})??II""HW/!
1 2 3 4 5 6
FAIL SAFE AND FAULT HANDLING CODES
When a fault is detected FX-Maxx will display one of the following Mnemonic fault codes:
HPF indicates high Freon pressure. 15 Second Delay Ignored in Heat Mode.
LAC indicates low AC line power
AAA ... .indicates failed air sensor. Unit will not run until repaired.
Fail-Safe
There are four levels of fail-safe protection including the fail-safe off mode. Level one monitors
the sensors, takes appropriate action and allows continuous restarts after a 90 second delay...
Does not display the fault code. Level two worjis the same as level one, however, the appropri-
ate fault code mnemonic is displayed during the time-out between restarts. Level three is identi-
cal to level two with the inclusion of a three successive failures lockout routine. After four [4]
consecutive failures the system is shut down and a manual reset is required.
Lockout
Lockout occurs if four consecutive faults are detected within a heating or cooling cycle. Lockout
causes the system to shut down and flash the appropriate mnemonic fault code. Lockout can only
be cleared by turning the unit off, then.on with the power button.
Fauit Display
When a fault occurs the appropriate mnemonic code is flashed in the display. The flashing mne-
monic can be removed from the display by pressing and releasing the power button to reset the
control. Resetting the control does not solve the problem that caused the fault!
Revision: 03 01/02/98
Page 5
FX-Maxx Operations Manual SPECIFICATIONS
SPECIFICATIONS
SET POINT RANGE 55°F to 85°F
TEMPERATURE RANGE DISPLAYED OaFto 150°F
TEMPERATURE SENSOR RANGE... ." ... ... ... .. ... .... OaFto 150°F
FREQUENCY """ ... '" ... 50 OR 60 Hz
FAN OUTPUT... ... """ """ """ 6 Amps @ 230 VAC
VALVE OR REA TER OUTPUT 6 Amps @ 230 VAC
PUMP OUTPUT 125 volt 1/4 HP @ 125 VAC
PUMP OUTPUT 250 volt 1/2 HP @ 250 VAC
COMPRESSOR OUTPUT 125volt 1 HP @ 125 VAC
COMPRESSOR OUTPUT 250 volt 2 HP @ 250 VAC
DISPLAY DIMENSIONS
DISPLAY PANEL 5.310" X 4.130"
DISPLAY PANEL CUT OUT 5.5" X 4.5"
PC BOARD DIMENSIONS
LENGTH ... ... """""" """ ..., 7.000"
WIDTH... """ ,. ... ... '" 3.750"
HEIGHT 1.560"
Revision: 03 01/02/98
Page 6
1
..J::.. DISPLAY OAT/H20 I I
~
n
Sdr
~I\I 11\1
C:::::>I
0
..J::..
ODD I c::> :R:: ~
OB n~ qOonD ~ ICLo ~
00 q g 01 qI g =~ ==>-
g QClo1o~IO\'-'{Jq~
DD
DI ID
OnJpl i
FX-Moxx f!l.erations Manual
Place this sensor
in
discharge air stream
~
0
Compressor
FX-MAxx WIRING DIAGRAM
Tank Full Cutout Switch
C olNO
r-- Place this sensor
/ inreturnairstream
AC
-1
t
L1
L2
ReversingVOlve 11OVor 230V
or trOlsformer con be comected
betweenvalve output Old valve.
Revision: 03 01/02/98
Page7
FX-Maxx f!J!.erationsManual
FX1-WilingDiagram
High Pressure Switch
D-~.So-\
-t DISPLAY OATIH2O 9dr. 1:11...J.W
nn
~-C::::::>I I
n
c:::JQOO~ -t
OB 'io QDjJ 0 g I 7'=
00 q ~ 01 QI"IHP ~
o
dB:
~ 0 d~n~nnONW ~
0
D -c::::J-
I
n a
D
V~~g
°
0
CJ! 1°
0 On nOc=> B
~ 0
L1 L2
Compressor
Reversing valve 11OVor 230V
or transformer can be connected
between \/ClIveoutput anv valve.
Revision: 03 01/02198
Page 8
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

OceanAire OWC6012 Owner's manual

OWC6012
OceanAire
Brand
OceanAire
Model
OWC6012
Category
Thermostats
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents