Haier ESA3083 Owner's manual

Page is loading ...

Thank You Forbuying a dependable, energy saving and easy to operate

HAJERroom air conditioner This manuaJcontains usefulinformation for

you to maintain, operate, install and safely useyour room air condifianer_

Your air conditioner deans, coals and dehumidifies the air in your room to

provide you with the ultimate bvel of comfort.

Pleaseread instructions carefully before using the producL Also, do not

forget to fiHout and mail the Product Registration Card.

Record Your ModeUand SeHaUNumber°

For all your service calls during the warranty period the bHowing

information will be needed. Affach the sales receipt to this guide and keep

for future reference. This information can be obtained from the serial pJate,

which is on your air conditioner: This is either on the cabinet (side or back)

or you may have to remove the front grille to Jocateit.

1) Air conditioner mustbeconnectedto proper electrical outlet with the

correct electrical supply. (seetabJe)

_. 2) Proper grounding mustbe ensuredto reducethe risk of shockand fire.

DO NOT CUTOR REMOVETHEGROUNDING PRONG. If you do

not have a three-prong electricreceptacleoutlet in thewall, have a certified

electrician install the proper receptacle. Thewall receptacleMUSTbe

properly grounded.

3) Do not use if power cord isfrayed or otherwise damaged. Also avoid

using it if there are cracks or abrasion damage along the length, plug or

connector.

4) DO NOT USEAN ADAPTEROR AN EXTENSIONCORD.

5) When installing your air conditioner in a window, make surethewindow

is strong enough to hold the weight of the air conditioner. Youalso want to

secureand correctly install your air conditioner properly to prevent it from

falling. Extrabracketsand or support may be required depending

on your window.

6) Do not block airflow inside or outside the air conditioner with blinds,

drapes, protectivecovers,shrubs or bushes.

7) Becareful of sharp edgeson thefront and rear fins of the unit that could

cut and causeseriousinjury.

8) Becareful when lifting the air conditioner to installor remove the unit.

Always usetwo or more people for this.

9) Always unplug theair conditioner before servicing it or moving it.

PAGE

A Word From Haler 1

P_duct Registration 1

Safely/Precautions 2

Warnings 4

ElectricaJSafely/ 4

Tips 5

Energy Saving Guide 5

FeQtures G-7

@peratlng Gulde 8-14

Normal Operating Sounds 8

Operating instructions 8-14

JnstaJJatians 15- 24

Parts ] 6

Tools ] 7

Installing Unit into A Window ]8-25

Clean and Care Gulde 2G-27

TroubUeshaoting 27 _28

Warran_ Jnfarmatian 2g

3

Following the safety messagesis very important.

Thesemessagescan save you from being injured or killed.

Warning symboRsalert you to be carefuRand means Danger. AJways

follow instructions to be safe and reduce chancesof injury or deatk

Warning and Danger signswill precede safety messages.

Grounding: This room air conditioner must be grounded.

Grounding reduces the risk oFenectricshock by

providing an escape wire for the electric current.

The power cord has a grounding wire with a

grounding pJug. PJugif into an outlet that is

properly installed and grounded.

WARNHNG: mmproperuseof the grounding

pJugcan resuJtin a risk of electric shock.

Coil a qualified electrician if you don't understand

the grounding instructions or if you are not

sureif the air conditioner is properly grounded.

mfthe wall eJectricaJoutlet is not grounded, please contact an

eJectricianto have if repJacedwith a properly

grounded outJet.

DO nOtr Under Qny ¢_rcu_st_n¢esr CUt or re_ove t_e

thlrd (ground) prong from the power ¢or_.

Adapter PUug: We strongly advise against using an adapter plug.

4

®Air Conditioners are designed for use in a douHe hung window or

through the wall installation only (As appJicable in your model)

®While installing unit be sureto tilt air conditioner _/4 inch ouhvard to

havethe water drip outside the house.

s_k o mnstanlthe unit on the north side as normanlythat is the shaded side This

winJenhance the operation of your unit.

Window has to be strong for installation. Extra brackets and or support

may be required depending on your window.

• Measure the window before installing, if thewindow is too big Forthe

unit you may require professional installation.

_'_ Usecorrect electric voJfageand proper ampere for the unit to run

effectively.

,_® Only let a certified eledrician do any modifications fo your eledricol

outlet,

o When installing your air conditioner make sure to seaJaHareas where

there is a possibiJify of air Jeakage.

Airflow should not be bJocked inside either by curtains, drapes or

furniture or outside by shrubs or bushes

Do not needJessJyuse an eJectricaJJightor other appliances that

produce heat

Keep the ventdosed on the air conditioner when in the cooling function.

Keep the bJindsand the drapes drawn on all the other windows.

o While cooking usean exhaust fan in the kitchen to remove the excess

heat produced.

Always usethe correct BTUsize air conditioner to cool the room to

attain optimum efficiency.

5

side vent

louvers

easy=access

fluters

(AH features not on alUmodds)

chassis

'J° Thermostat

This allows you to adjust the temperature of the ain

The lower the sobbingthe coder the air temperature

with this you can set the temperature to your

desired comfort levd You can setthe temperature

behueen 61 _ F and 86 ° F

2. Fan Speed

With this you can contrd the fan speed as ",veil as

the A/C (coding) speed

You have 3 levels of A/C Speed for you to setat

your desired levd LO will chdate air at the

lowest vdoci_y, MED at medium vdocity and HUGH

will cirdate at the maximum

You have 2 lords of Fan Speed to setat your

desired comfort levd MED and LO

Auto Fan allows the room temperature to setthe fan

speed When the function is set, fan speed is to be

determined according to the difterence belween the

s_ttemperature and the temperature inside the

room Once the settemperature is reached the fan

will run at the LQ Setting

3. Function.

Your air conditioner has 3 Functions

a)A/C,

Here the air conditioner will operate the compressor

and the desired fan speed set to give you chilled

cold air for your comfort

b) Dehumid

This enables your air conditioner to operate as a

dehumidifier as we[[ Jtwi[[ remove the excess

moisture from the air to keep your room at a

comfortabJe dry stage You can use this feature

alone in case you do not desire to usethe air

conditioner

c) Fan Only

You can run the fan only on not so hot days The

fan can be set to run at 2 speeds (rned fan, low fan)

as desired by you

4° Energy Saver

\_Vhenturned "ON" the fan "will shut off 3 rnlnutes

after the compressor cycle off. This will not only

save you electrical and energy costs but also shuts

off the unnecessary noise of the fan motor running

In the "OFF" position the fan will not shut off when

the compressor cycles off The fan will keep running

at the setlevel

5o Timer

Your air conditioner can Be setto go on or off at

your deske This can be done up to 12 hours in

advance

6

6. Vent (not hi aH modds)

This feature hdps you to exhaust any stole

unwanted air from the room and draw fresh outside

air in the room Tocirdate the air, bring the lever

to the open position ( right ) 1o r_toin the cooJ it is best

to keep this in the dosed mode (left)

7° Air Sweep (not in aH modds}

When left on "ON" this automatically d stributes the

air through out the room This will ensure an even

airflow through out the room

8_ 4 Way Air Flow

These air directional Jouverslet you control the

directio__of the airflow in your required direction

The airflow can Bedirected

up - down - right side - left side

9o Sllde Out Chassis (,lot on aH modeJs}

Your Air Conditioner becomes more versatile with

this fuature You have the option to instoll the unit in

a window or the wall

10. Wir_dow mnstaJJKit

Enables you to install the air conditioner in a

double hung window Extra bracketsor support

may be needed depending on your window

1'J° Re_ote ¢oe_rom

This full functional wireless remote allows you to

operate your air conditlor_er from a d_stoace You

need not have to get up to change the se#ings, the

functions or to turn the unit on or off

12. LED DispJay EJectroel¢ Coeds| PaeeJ

The 4 function LEDdisplays Room]emperature,

Temperature Setting, Timer Setting and Time

Remaining to Stop / Start the unit Electronic

Control Panel letsyou setthe temperature to the

Exact Temperature you desire

13° EJect_st_ti¢ FiJter

Being constructed of high efficiency purifying

substance, active carbon fabric, electrostatic fabric,

electrostatic active carbon net and other materials

it purifies the air effectively ffswavy structure

increases the capability to hirer dust and smoke

effectively Due to the retention of the acti,,e carbon,

it has a high purifying speed capable of

strong aid{ow

14. SJeep

When activated, this feature automatically setsan 8

hour shut off timer The unit will shut off in 8 hours

lllerm l @le tlHg Se ds

The folowing sounds are normally heard during the operation of an air conditioner,

o Cod airflow movement as didated by the set fan speed.

Water sounds. This is normaJas your air conditioner acts as a

dehumidifier aJso.Thusyou wil hear water sounds from water drops

faling on the condenser.

As the refrigerant tows through the inner sealed tubing a rushing noise

may be heard.

Railing or vibrating noises may be heard due to poor wal

or window instalafion.

* High pitch compressor sound may be heard.

@pe ethsg Ins tru¢lieHs

Folowing are the operating instructionsof your electronic air conditioner.

After instaling your air conditioner pJugit in to the proper dectricaJ outJet

in the wal Keepthe vent in the closed position. Now set the air

conditioner at your comfort bye[ This ful functional wireJessremote alows

you to operate your air conditioner without having to get up and go to the

unit. The ful function feature alows you to change the settings and turn the

unit on or off from the remote itseJf.This controJpad works the same as

the control pad on the air conditioner.

(See Fig # ])

Fig. # 1

Remote ¢@ntr@J

After you plug in the unit it wi[[ perform a self test. A[[ the display tights

will turn on for 3 seconds. The LED display will read "88". If any dispnay

light fails to turn on you may need service on the unit. After the 3 seconds

self test the unit will automatically go to the stand by mode. Now all lights

will be off and you wilt have to turn "ON" by pressing the On/Off key

After pressing "On/Off", the unit starts to work and enters the status of

"Fan Only" with low seffing. You will haveto press the (+) or (o} key on the

TempiTime to set the temperature af your desired comfort. You can choose

bebNeen 61 °F and 86°R Once the temperature is set you can raise or

lower it by pressing the (+) or (o) keys. (Only when the unit is cooling or

dehumidi_ing, can the temperature seffing be adiusted.} (See Fig, # 2)

PaneH_

FA_ MEO _L_EP

Having set the temperature you will set the function of the air conditioner.

mfyou want to cool the room press the AiC function, mfyou need to onJy

remove the moisture press the Dehumid function. If you iust need to usethe

fan only, press the Fan function. (See Fig. # 3)

Fig.#3

¢ontrom Panel

Fig. # 4

¢ontrom

Once the function mode is decided you wiHIhave to set the fan speed_ If

you choose the A/C mode you can run the fan in one of the 3 speeds Hi,

Med., Lo or in the Aub speed, mnthe Auto speed the fan wiHIstart at High,

Med or Lo as the temperature varies in the room.

Tr: temperature inside the room.

Ts:the set temperature.

When Tr >Ts+2°F, the Hi is to be automatically. When Tr<Ts, the Lo is to be

set. When Ts<Tr_<Ts+2°F,the Med is to be set. Once the set temperature in

the room is reached the Auto fan setting wilH have the fan running on Lo.

]_takes 3 minutes to switch the fan speed, (See Fig # 4)

Panel

10

HFyou choose b use the Dehumid function, Thiswill remove excessmoisture

from the air on excessivelyhumid days.

Tr temperature inside _heroom,

Ts: _hese_femperature.

] ) When Tr>Ts+3°F,the compressor wilJ run confinuousJythe fan at the

selectedspeed.

2)When Ts°l°F<Tr<Ts+3°Fthe compressor wilJ cycle for 10 minutes on

and 6 minutesoff.

3)When Tr<Tsol°F,the compressor wilJshut off,

The dehumidification process takespJace betweenthe settemperature _1

and 3°Fabove the settemperature. (See Fig # 5)

Fig. # 5

Control Panel.

For cooJdays you may want to run the "Fan Only" function. Here the fan

runsonJyaf one of 2 speeds,Meal or Lo. Thefan will not run at fhe High

speed. ISee Fig. # 6)

Fig # 6

¢ontrom Panel

11

Fig. # 7

Control

Timer start or Timer stop mode is used to pre-start or shut off your unit in

advance. You can program this up to ! 2 hours in advance. You can use

the Timer in 3 Functions i.e. A/C, Dehumid. or Fan Only

eTimer Start. (See Fig. # 7)

Unit must be on to set the timer. Unit will shut down automatically after it

accepts the settings in 5 seconds Use this mode to pre-sef the start time of

the unit 12 hours in advance.

a) Press Start, LED dispUay wilU show "XX" (time set Uasttime) when power

is connected first time, LED display wiUl show "01" .

b) Set desired number of hours by pressing the (+) pad of the Temp/Time

buHons, one for each hour. If you passed the desired time use the 1-1pad

key to lower the selection.

oTimer Stop (See Fig # 7)

Unit must be running to set the timer off. Use this to preset the time you

would like the unit to shut off.

a) Press Stop, LED display will show "XX" (time set last time) when power

is connected first time, LED display will show "01"

b) Set desired number by pressing the (+) pad of the Temp/Time buttons.

One for each hour. If you passed the desired time, use the (o) pad key to

lower the selection.

When using the timer the unit wilJ use!revert to the last A/C and fan

settings when activated. The timer must be reset every time you choose to

use it.

PQ_e_

Ha Jet

O©O

Pressingthe mode onetime, the settingof Timerstart,Timer stopand sleep

can be done. Pressingthe mode Fora secondtime, the settingiscancelled.

12

SJeepJetsyou preset the unit to shutoff in 8 hours. SJeepworks in the AiC

function only. After preoseffingthe temperature to a set degree,

the temperature raises by 2 degree in the Ist hour and another 2 degree

in the 2nd hour and then remains constant in the next 6 hours As your

body does not give out as much heat in the night and as nights generally

become cooler this feature Jetsyou sJeepcomfortably throughout the night

without having to wake up to change the temperature settings.

(See Fig. # 8}

Fig. # 8

¢ontroU Panem

HaJ_r

FC

Air Sweep: By pressing this key theAir Sweepwill be activated. Thiswill

give you an even airflow throughout the room. To shut it of]:you will have

to pressthe key again (See Fig # 9) (For ESA3063, the flmction is not

available)

EnergySaver: By pressing this key you will activate the unit to go in the

energy saver mode. The fan wiJJbe off 3 minutes after the compressor

cycle off. Bydeactivating it the fan keepsrunning at the set speedeven if

the compressor shutsoff. (SeeFig. # 9) (Thisfunction isavaiJable in the

cooJing function only)

13

Fig. # 9

¢ontroJ PQneJ_

kS ',_

When unit is in "On" mode the LEDdisplay wil showroom temperature.

Pressthe (+) keyto get settemperature.When unit is in "Timer Stop" funco

tion, LEDdispJaywil show the time Jefffor the unit to shut off.

Tocancd Timer Stop pressthe main Off key.

"H" Jightis on the time is shown.

"°F"light ison the temperatureis shown

14

Before you install your air conditioner check the foJ[owing:

1) The unit is free of a[[ obstructions inside and outside the room eg. drapes,

curtains, furniture, pJants,shrubs,bushes, trees, other structures[ike building,

garage etc Air conditioner musthave dear unobstructed airflow through the

condenser to remove the heat

2) Thewindow is strong enough to hold the weight of the air conditioner.

Extra brackets or supports may be needed depending on your windows.

3) Thewindow si[[and track are strong enough to hold the weight of the

air conditionen

4) Thewail is strong enough to hold the unit. Extra brackets or supports may be

needed depending on the wail

5) There is adequate and proper power supply near the air conditioner.

_6) DO NOT useadapter plugs.

_7) DO NOT useextension cords.

_8) DO NOT cut or remove the ground prong.

9) DO NOT modify the plug or the eJectrica[waJ[outlet in any way.

mfpJug does not fit the dectricd outlet have a certified electrician do the

necessarychange.

_10) DO NOT connect electrical power to the unit before installation.

_1 ! ) DO NOT use if power cord is worn out, frayed or otherwise damaged

Avoid using if there are cracks or abrasion damage along the length,

plug or connection.

15

Parts

Parts Suppli{ d

window seal

gasket

_¢_ curtain

_ attachnlenl

screws 13/32"

curtain sash

screws

31/32"

basepan angle

Remote 'CR2025" batte*v

control

electrostatic filter

blodel: ESA3063

Parts Suppli{ d

_ window seal

r,//M/ gasket

_2- Z_73

curtain Cllrlain sash screws

_;_ attachment 31/32"

¢_,{_ screws _5_13/32"

Casenlent to

window

securance screw 1"

_ _ basepan angle

'+(R2025" hatte U

%&Remole

control

left and right

side curtains

Model: t SA3083

Parts Suppli{ d

/_// window seal

,(_// gasket

"_7- £ZTJ

curtain

{g_ £_ altachnlent

{;_ _screws 13/32"

dlah_ robe

curtain sash screws

31/32"

Casement to

window

securance screw ]

0

"(R2025' batmry

Remot_

control

e[ec ros'iofic fiJter

Model: ESA3103, ESA3123

hasei}an angl{

left and right

side curtanls

16

You will need to have the fallowing tods to help yau in the installation of

your air condifianen

®Sdssars

_PhiHipsScrewdriver

oStandard Screwdriver

oPliers

eWrench

•DriJJand DriH Bits

oTapeMeasure

eGJaves

®Level

oSackets

17

Installing Unit into A Window

Window Opening Requirements

The aiI conditioner is designed to fit into double or single hung sash type windows. Each of the

units comes wifl_ an ins_'aHation kit that provides adjus_'aMe mounting _ouvers, to fiH_'he gaps

between _'he sides of _'heunit, and _'hewindow flame. The chart below reflects the dimensions of

_'heunits with, and without installation kits. Measure your window opening widflJ and compare

itto file chart below to ensure {ha_it mee{s the minimum and maximum window wi&h requkements.

' i

i

ESA3063 ESA3083, ESA3103, ESA3123

_ ESA3 [ 03

ESA3063 ESA3083 ESA3123

A(indl)

g(indl) _:@

C(h_ch)

DOnch) Max 2a_,,

D(inch) Min 235"

Case High I3ll_;' I5@

Case Wklfl_ 2(_1:'

Case Depth _-_@

Model ESA2_O(_3

ASSEMBLE

CURTAINS

insl llh6oli 1o(alion

Slkle leJl hand (uimin assembly inlo

left ends of _op and bottom la_ls

Repea_ for i_ghl hand curlain

assembly Fas{en _ur_a_n rela_ner

s_ips _o skies of outer case w_lh six

13/32" screws¸

18

m

PREPARE

WINDOW FOR

INSTALLATION

]nspe/i window ira/k, sash. md sill

for i_stbililv lo sllppor_ _he weight of

_Jil/ ondiii/luei

Measuw width b(,iweell window

mok[iIlgS kl eiIs[ffe hlsial]_ Mouili

will lit will(tow hame Illsianl Moun_

ii]o([els are deslgIled _(11¸whldows

wide (_he deiail See Page 18)

]llsia11I Mouni kil supplied wlih Llnil

is d esigned [(11¸ illO[[llii_lg ill I11(ISi

double huIlgwil]dows wi[hou_

st()]-m wil K[o_,\ s For iIiS_allaiion ill

willdow h'allle wi_ll siolm window¸

modi_ sill by adding wood slrips

(lloi included) Io illller and outer sills

This raises unil and ellminales

inierlerence of sIorlll wi[K[OW [Iame

SIorm window illsial[a/iotl

]f Slol Ill Will(tOW l} [lIl( _ does 11o[ allow

idequat(/learan(e below sill (I/2'

requiwd), r( ItK)Ve S[OI'III WIII([OW

l_a_le ol creaR, clearanc( by adding

a wood strip (ai leas{ I 1/2" wide)

dolls enike widlh of sill }'aaen

wood sIrip lo sill with a_ lt,as_ [hi {_P

cotlltiers{[llk wood sol'( _,:_ (noi

supplied with ki0 _[his pro/kk,s a

f:ondi_iogl( r

MmEm,n,,

.....

M[t/[it/ll]t

Mobile home wi]ldow hlstallation

Add wood sirip (ai leasi 1 12' wlde)

akmg enii*_ _qdih ol wi_KIow sill

Thickn( ss of wood slrip shouk[ mtich

h( ight ol ff(ini lip ou windm_ h'ame

Fasten wood strip to sill wiih a

l/llltll]lUtti of lhree (O[[llierS[[llk _oo([

screws (noi supplied wiih ki0 This

provkles a smooih surface lbl

l/KK[llii_lg ail ( oudiik_n( 1

Mustbea minimum

of 1/2' to detr

.....g;;Zi a!

o D

[_/.../ ....... i'

INSTALL UNIT IN

WINDOW

P]ale [[nil ill winding, l_o_/_r sash

tmli! it resis behind lronl lkmge ol it,ll

rai_ Bottom lail must It'si behind

tt il]dow sill

5 o

INSTALL

BASEPAN ANGLE

[{[(k lion{ aiiachnl( lit s(rew ot[t

several ruins and slip gasepan Angle

ovel screw head _iltlg sclew w]{]l

angle *esling on wil]d ov_ ledge

]nsiall "f_o 31 32" s(rews _hrough

angle into window ledge R{pea_ fi_r

opposite si(k

31/32"

screws

angle

19

SECURESmDECURTAINS

AND TOPMOUNTING RAiL

Expand curtains as far as possible \\"

Instal[ (2) 31/32 '_ curtain sash

screws. Unstal[ (3) 25_mm top mounting

rail For hard wood or metal

window frames, drill a pilot hole

fo starJ screw

JMPORTA't',JT: Be careful not to ddJJ

pilot hole too deep Add a piece of

tape to the drill bit as a depth

gauge Also stay dear of glass Be

careful not ta damage the function

of the window.

INSTALLSEAL

GASKET

Cut window seal gasket to width of

window Stuff window seal gasket

between outdoor window glass

and tap of indoor sash This wiJJ

stop air leakage which reduces

eft ciency

Models ESA3083, ESA3]03, ESA3123

I REPAREUNIT

FOR

[NSTALLATJON

Unpack unit on fJoor next te

installation location

Remove h'ont ottechment screw

Separate the outercase from the front

with a putty knife af the catch points

designated by the arrows

Remove one screw securing

bosepan Jacking bracket Remove

f,uo screws located in the rear of the

outercase, securing basepan to

outercase Using the basepan handle,

slowly and evenly pu[[ chassis out

from outer case

Note: Cover"putty knife Blade _vi[h

masking tape to guard against

damage of the units finish The filter

is removed in this illustration for

clarity only

Caution: Never expose plastic

front or grille to extreme

temperatures

2O

Page is loading ...

Haier ESA3083 Owner's manual

This manual is also suitable for

Haier ESA3083 Owner's manual

in other languages

Related papers

Other documents