Kenmore 25379125991 Owner's manual

RecordYour Model and Serial Numbers .............. Cover

Important Safety Instructions ....................................... 2

Energy Saving Ideas ...................................................... 2

How and Why ................................................................ 3

Normal Sounds .............................................................. 3

Front Installation ........................................................ 4-5

Using the Air Conditioner ............................................. 6

Air Conditioner Features ............................................ 6-7

Care and Cleaning ...................................................... 7-8

Routine Maintenance .................................................... 9

Troubleshooting Guide ................................................ 10

Sears Service ................................................................ 11

Warranty ...................................................................... 11

Read and Save These Instructions

This Owner's Guide provides specific operating instructions for your model. Use the air conditioner only as instructed in this

guide. These instructions are not meant to cover every possible condition and situation that may occur. Common

senseand caution must be practiced when installing, operating, and maintaining any appliance.

Record Your Model and Serial Numbers

Record in the space provided below the model and serial numbers. The serial plate islocated behind the left front louvers.

Readingthe numbers may be easier by using a flashlight or by removing the cabinet front as instructed under "Care and

Cleaning." On some models, the serialplate is located on the outside of the cabinet.

Model Number:

Serial Number:

I Purchase Date:

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

P/N 309000817 (9903)

Important Safety

Instructions

Avoid fire hazard or

__lectricshock. Donot useanextensioncord

_r an adaptor plug. Do not remove any

_rong from the power cord.

Grounding type

wall

Power supply

cord with 3-prong

grounding plug

Read all instructions before using this air conditioner.

For Your Safety

Do not store or use gasoline or other flammable vapors and liquids in the

vicinity of this or any other appliance. Read product labels for flammability and

other warnings

Prevent Accidents

To reduce the risk of fire, electdca! shock, or injury to persons when using your

air conditioner, follow basic precautions, including the following:

• Be sure the electrical service _sadequate for the model you have chosen.

• If the air conditioner is to be installed in a window, you will probably want

to clean both sides of the glass first. If the window isa triple-track type with

a screen panel included, you may want to remove the screen completely

before installation

• Be sure the air conditioner has been securely and correctly installed

according to the separate installation instructions provided with this manual.

Save this manual and installation instructions for possible future use in

removing or reinstalling this unit.

• When handling the air conditioner, be careful to avoid cuts from sharp

metal fins on front and rear coils.

Electrical Information

The complete electrical rating of your new room air conditioner is stated on

the serial plate Refer to the rating when checking the electrical requirements.

• Be sure the air conditioner is properly grounded. To minimize shock and fire

hazards, proper grounding is important. The power cord is equipped with a

three-prong grounding plug for protection against shock hazards.

• Your air conditioner must be used in a properly grounded wail receptacle. If

the wall receptacle you intend to use is not adequately grounded or

protected by a time delay fuse or circuit breaker, have a qualified electrician

install the proper receptacle.

• Do not run air conditioner with outside protective cover in place. This could

result in mechanical damage within the air conditioner.

• Do not use an extension cord or an adapter plug.

Energy Saving Ideas

• The capacity of the room air conditioner must fit the room size for efficient

and satisfactory operation.

• Install the room air conditioner on the shady side of your home, A window

that faces north isbest because it is shaded most of the day.

• Do not block air flow inside with blinds, curtains or furniture; or outside with

shrubs, enclosures, or other buildings.

• Close the fireplace damper, floor and wall registers so cool air does not

escape up the chimney and into the duct work.

• Keep blinds and drapes in other windows closed during the sunniest part of the

day.

• Clean the air filter as recommended in the section "Care and Cleaning."

• Proper insulation and weather stripping in your home will help keep warm

air out and cool air in.

• External house shading with trees, plants or awnings will help reduce the air

conditioner's work load

• Operate heat producing appliances such as ranges, washers, dryers and

dishwashers during the coolest part of the day.

I

Yourroomairconditionerprovidesthefollowingfunctionstomakehot

weatherlivingmorecomfortable:

How and Why

• Cools and circulates room air.

• Lowers humidity by removing excess moisture.

• Filters out summertime dust, dirt, and some airborne impurities.

The air conditioner performs these functions by drawing room air through a

filter which traps dust and dirt particles. The air then passesover a cooling coil

which refrigerates the air and removes excessmoisture. The same air is then

returned to the room-- cooler, drier and cleaner. Moisture removed from the

room air is carried to the outside and evaporated.

Your air conditioner is designed to be easy to operate and to provide plenty

of cooling power.

Normal Sounds

Compressor

The high efficiency

compressor may have a

high pitched hum or pulsating

noise that cycles on and off.

Unit Vibration

The unit may vibrate and

make noise because of poor

wall or window construction,

Fan

You may hear air movement._

from the fan.

Thermostat

As the cooling

the thermostat may click.

Condenser

may hear droplets of

water hitting the condenser

causing a "pinging or

clicking" sound.

Front Installation

Installina Bottom RailSeal

Vertical Louver _

Screw

J.

Unit Cover

%_-_-_Screw

Horizontal

Louvers ont Panel

Front Installation - Side Air Discharge

FIG 1

Front Installation - Side Air Discharge

FIG 2

Installing Bottom Rail Seal (some models)

Some models are shipped in a removable sleevethat must be positioned properly for

safe and efficient sealing. Follow the Installation Instructions supplied. To install the

Bottom RailSeal,position the sealon top of the bottom rail, flush with the front edge

of the rail and in contact with the sideseals.

Manual Vertical Louver Adjustment (side air discharge)

Complete this adjustment before installing front panel.

I. Adjust the vertical louvers to the straight position by using the handle.

2. The dial plate and knobs are packed separately. To install them, refer to

Installing the Dial Plate and Front Frame section on the next page.

Front Installation - Some Side Air Discharge Models (FIG. 1)

Install the front panel with filter as follows:

1. Adjust the horizontal louvers to the straight position. Hold the front straight

until the vertical louver handle lines up between the bottom horizontal louver

and the discharge opening.

2. Pressthe front straight onto the cabinet until the holes in the flange of the

plastic front line up with the screw holes in the metal cabinet. Fastenthe front

panel in place with the two screws provided.

Front Installation - Some Side Air Discharge Models (FIG. 2)

1. Position the top of the decorative front cover onto the top flange of metal case

and then align the tabs on the front with slots in metal case.

2. Carefully pull down on the front cover to engage top tabs while pushing the

front cover over the metal case. To ensure proper alignment the side

locking tabs will "click" when the front cover is properly installed.

Note: Power cord must be held in position inside metal casehalf-round relief

while sliding front cover over metal case.

3. Install the front cover retaining screw at the bottom of the unit.

Installing the Vent Control (on some models)

The vent control handle isincluded in the decorative front kit (Fig. 3). The handle

must be installed before the decorative front is attached. See illustration below.

I. Insert the handle with the "Etchings (Vent/Air)" facing to the left.

2. Slipthe black door extension into the split at the end of the handle.

3. Foreaseof assembly,Pusgthe handle in while pressing the door extension

against the foam until the two pieces lock together.

4. Move handle inand out to be sure vent isoperating properly

FIG. 3

4

Front Installation

(continued)

Installing Dial Plate and Front Frame

Some models require installation of the dial plate and the front panel of the air

conditioner included in a decorative kit. To assemble, follow these steps.

STEP 1: INSTALL DIAL PLATE AND BUTTONS OR KNOBS:

Some Models

\ /

Side Air Discharge

• Remove control knobs from front kit

(some models).

• Carefully remove protective film

from the front of the dial plate

(some models).

• Line up holes on dial plate with the

correct control stems and push dial

plate to control panel surface.

• While holding dial plate in place

install control knobs on protruding

stems.

STEP 2: INSTALL FRONT FRAME TO UNIT.

Decorative Front

• Position the top of the decorative front over the top flange of the case, and align the tabswith the

slots in the case.

• Asyou install the front frame to the unit be surethe vent handle ispositioned through the front in the proper

location.

• Carefully pull down on the front to engage the top tabs, while pushing the front over the case to

ensure proper alignment.

• The side tabs will "click" when front is seated.

• Install front retaining screw(s) at the bottom of the front (Fig. I), or behind the filter handle (Fig. 2).

FIG. 1

FIG.2

Using the Air Conditioner To reduce the risk of fire, electric shock,or injuryto persons,read the

IMPORTANT SAFETYINSTRUCTIONSbefore operating this appliance.

NOTE: If the air conditioner isturned off,

wait 3 minutes before restarting. This

allows pressure inside the compressor to

equalize. Failure to follow these

instructions may cause inefficient

operation.

To begin operating the air conditioner, follow these steps:

I. Plug in the air conditioner. (To prevent electrical hazards, do not use an

extension cord or an adapter plug.)

2. Setthe exhaust vent to the CLOSED position.

3. Setthe TEMP Control to the coolest setting.

4. Setthe fan control at the highest level.

5. Adjust the louvers for comfortable air flow.

6. Once the room has cooled, select the POWERSAVERMODE andlor adjust the

TEMP Control to the setting you find most comfortable.

Review the "Air Conditioner Features" section for other settings.

Air Conditioner Features

VENT

OPEN CLOSE

MODE

OFF

HIGH _ FAN

T

MED \\ ' //POWER

COOL _ SAVER

LOW

COOL

TEMP

• 5 •

1 9

COOLER

(some models)

COOL

HIGH

LOW

HEATControl (some models)

The controls featured in this manual are representational of the many models

available. Your model may look slightly different.

TEMP Control

The TEMP Control servesas the thermostat to set the degree of room

coolness. Turn the knob clockwise from 1 to 9 to increase the cooling

temperature.

COOL MODES

When in one of the COOL settings, the air conditioner runs all the time,

circulating the air. Cooling starts only if the room temperature rises above the

coolness level selected on the TEMP Control, and stops once the set coolness

level is reached. This setting gives the most even room temperatures.

POWER SAVER MODE (some models)

The POWERSAVERMODE can save energy. In this setting, the fan will not run

unless the TEMP Control isset colder than the room temperature. When the

TEMP Control is set colder than room temperature, the air conditioner will

begin to circulate the air in the room. Cooling will begin in about 3 minutes.

The air conditioner turns off automaticalJy when the room reaches the level of

coolness selected. HIGH COOL is for fast cooling, MED. COOL isfor normal

cooling, and LOW COOL isfor quiet cooling.

HEAT (some models)

The HEAT selection provides quiet, efficient circulation of warm air. Turn the

selector to the HEAT setting and set the thermostat to the warmest setting.

When the HEATsetting isselected, the thermostat maintains the temperature by

automatically turning the heater on and off in response to room tempera-

ture. Once the room is warm, adjust the thermostat to a cooler setting. The

fan runs continuously to circulate air in the room.

MODE

OFF

HIGH FAN

COOco01._ONLY

MED POWER

SAVER

COOL

VENT

CLOSED

TEMP

• 5 •

1 9

COOLER

EXHAUST

HEAVYDU_

Side Air Model Control Panel

6

Air Conditioner Features

(continued)

I

FIG. 1 (OFF)

FIG.2 (FRESHAIR)

FIG.3 (VENT)

A slight heat odor may come from the unit when first switching to HEATafter

the cooling season is over. this odor, caused by fine dust particles on the

heater, will disappear quickly.

Vent Control

The Vent Control allows the air conditioner to either recirculate inside air

(CLOSED)or exhaust air to the outside (OPEN).

• The CLOSEDposition is used when maximum cooling isdesired. It may also

be used for air recirculation without cooling when the air conditioner is set

in the FAN position.

• The OPENposition removes stale air from the room and exhausts it to the

outside. Fresh air is drawn into the room through normal air passages

found in homes.

• The OPENor CLOSEDposition can be used with any fan selection.

• For compact models, push the slide in to CLOSE, pull out to OPEN.

Fresh Air Vent Control

The FreshAir Vent allows the air conditioner to recirculate inside air (OFF),

draw air into the room (FRESHAIR) or exhaust stale air to the outside (VENT).

See Figures 1,2 & 3 for this operation.

Air Directional Louvers

The air directional louvers control the air flow direction. Adjust louvers up,

down, left or right. The outside tabs adjust the air up or down. The center

levers direct the air left or right.

Care and Cleaning

Figure 1

Clean your air conditioner occasionally to keep it looking new. Be sure to unplug

the unit before cleaning to prevent shock or fire hazards.

Air Filter Cleaning

The air filter should be checked at least once a month to seeif cleaning is necessary.

Trapped particles in the filter canbuild up and causean accumulation of frost on the

cooling coils.Theseconditions reducecooling capacity. Thereare two types of filters:

the rigid filter and the floppy filter.

Models with rigid filters allow you to remove the filter without removing front:

• Some models, push the vent control handle to the OFF position. Liftthe filter straight

up and out (Figure 1).

Care and Cleaning cont.

Figure 2

Figure 3

Remove

Knobs

Remove

Screw.

Pressfirmlyon eachsideof

caseto releaselocking tabs;

Figure 4

Removing Decorative Front - Some Models

Front

Figure !

SliderCasement Front

• 6-waylouvermodelshaveaslideoutfilter. Grasptheformedhandleofthefilterand

pull it to the left, removing it from the front panel (Figure 2).

• Formost installations in the window, this front may need to be removed to access

the filter for cleaning (Figure3). To remove the front, reversethe installation process

for SideAir Discharge Models shown in Front Installation.

• Somemodels require the louvers to be tilted in the up position, before pulling the

filter out. Placethe thimb under the center handle and pinch the top of the filter bar

with your forefinger while pulling the filter up and out asshpwn in Figure 6.

Washfilter usingaliquid dishwashingdetergent and warm water. Rinsefilter thoroughly.

Gently shakeexcesswater from the filter. Dryfilter thoroughly before replacing.

Cabinet Cleaning

• Besureto unplug the air conditioner to preventshock or fire hazard.Thecabinet and

front maybedustedwith anoil-free clothor washedwith acloth dampenedinasolution

of warm water and mild liquid dishwashingdetergent. Rinsethoroughly andwipe dry.

• Never useharsh cleaners,wax or polish on the cabinet front.

• Besure to wring excesswater from the cloth before wiping around the controls.

Excesswater in or around the controls may cause damage to the air conditioner.

• The cabinet front can be removed for more thorough cleaning. Refer to "Front

Installation" in this manual and Figures4 and 5.

• Cleanthe front in a sink using liquid dishwashing detergent and warm

water. Rinsethoroughly and dry. Becareful not to disturb soft sealson the front.

• Replacecabinet front. Replacethe screws or hex nuts.

• Replacefront panel and filter. Plug in air conditioner.

Decorative Front and Dial Plate Removal

1. Unplug power cord from the wall outlet.

2. Removeknobsbypullingfirmly, andthen removedialplate.Removefront retainingscrew

from thefront (seeFigure4 or 5 for screwlocation,whicheverissimilarto your model).

3. Pressfirmly on each sideof the metal casecloseto the front, approximately half way

down for Figure 4, or 2/3 the way down from Figure 5 from the top of the front

4. While pressing on the sides of the metal case, gently pull the front out and lif

up to release it from the case.

To reinstall:

Properreinstallation of decorative front isimportant for both safety and performance.

2. Position the top of the decorative front on the top flange of the case and align

the tabs on the front with the slots in the case. On some models remove the filter

to expose the two (2) front retaining screws.

3. Carefully pull down on the front to engage the top tabs while pushing the front

over the caseto ensure proper alignment. The side locking tabs will "click" when

the front is properly installed.

4. Install the front retaining screw (seeFigure 4 or 5 for screw location, whichever

is similar to your model).

5. Install the knobs by aligning them with their shafts and pushing firmly into place.

Winter Storage

Ifyouplanto storetheairconditioner duringthe winter, removeitcarefullyfrom thewindow

accordingtotheinstallationinstructions.Coveritwith plasticor returnittotheoriginalcarton.

NOTE: To prevent rust or electrical connectionsfrom being damaged, store air

conditionerinanupright positionanda dryplace.Awintercovercanbepurchasedfrom

ourdealer.Thecoverwillprotecttheairconditionerwhen itisleftinplacethroughthewinter.

3. Pull Filter Out and Up

1. Tilt Louver

Up

Louver

2. Pinch Center

Handle Here

Routine Maintenance

Winter Storage

If you planto storethe airconditionerduring the winter, removeit carefully from

the window accordingtothe installationinstructions.Coverit with plasticor

returnit to the originalcarton. NOTE: To prevent rust or electrical

connections from being damaged, store air conditioner in an upright

position and a dry place. A winter covercan bepurchasedfrom yourdealer.

The coverwill protectthe airconditionerwhen it isleft inplacethrough the

winter.

Before performing any service, unplug the power cord

from the electrical outlet.

After servicing,reversethe following procedures to reinstallthe air

conditioner.

Cleaning the Cabinet Front

Removethe front panel. Washwith warm, sudsywater. Rinseand drywith a soft

cloth. Neverusesolvents,cleaningfluids,abrasivecleanersor strongdetergents.If

the packagingleavesa gum residue,removewith a clothdippedin rubbing

alcohol.

Repairing Paint Damage

Inspectweather-exposedparts (cabinetshell,mounting hardware, ifused,etc.)

onceor twice a year, especially in areasnearoceansor where rustisa problem. If

needed,touch up with a good gradeof exterior paint.

Cleaning Inside the Air Conditioner

No Liquid shouldget into the motor, electrical control box, or

compressor electrical terminals.

1. Remove front panel.

2. With help and usingthe proper lifting methods to avoid personal injury,

remove the chassisfrom cabinet shell.* When removing the air

conditioner from cabinet shell or window, there may be water insidethe

basethat may spill on the floor. Becareful to avoid cutsfrom sharpmetal

-finson the front and rear coils.

3. Liquids should not get into electrical parts. Wrap the fan motor, electrical

control box, and electricalterminals in plastic.This will keep water or

other liquid from getting insidewhere it could damage the insulationand

cause serious trouble.

4. Clean and hose out base, coils, and water pans. Clean at least once a year

or more often if the coils and pans collect dirt, sand, leaves, algae, or

insects.

5. After cleaning, remove plastic protection. Wait 24 hours before starting

the unit again. This allows time for all areas to dry out.

NOTE: Water from rainfall or from normal use does not harm these

components since the water is not asforcefully driven into parts as a

stream of water from a garden hose.

*HANDLE NOTE: If the air conditioner hasa chassis handle, it is NOT intended for

lifting the unit. It isfor sliding the chassis WITHIN the cabinet shell only (to aid in

cleaning, maintenance, etc.).

9

Room Air Conditioner Troubleshooting Guide

®

THE AIR CONDITIONER WILL NOT OPERATE

Check if...

The power supply cord is unplugged.

A household fuse has blown or circuit breaker

tripped.

The Fan Control is set to OFF

Then...

Firmly plug the cord into a live outlet with proper voltage.

Replace the fuse or reset the circuit. Make sure the unit is plugged into a

properly grounded receptacle as described in the Owners Manual

provided with the unit.

Set Fan Control to the desired setting.

THE UNIT BLOWS FUSES OR TRIPS CIRCUIT BREAKER

Check if... Then...

Too many appliances are being used on the Unplug or relocate appliances that share the same circuit.

same circuit.

An extension cord is being used with the unit. Do not use an extension cord to run the air conditioner.

The unit is being restarted immediately after Wait three minutes after turning off cooling circuit before trying to restart

turning off cooling circuit, unit.

THE AIR CONDITIONER TURNS ON AND OFF, OR DOES NOT COOL ROOM

Check if... Then...

The filter is dirty or obstructed by debris. Clean filter using a vacuum cleaner or wash filter in warm water and a

mild detergent. Dry thoroughly before reuse.

The coils are dirty or obstructed by debris. Check Call the local Sears store to inspect and clean the coils and condensate

both inside evaporator and outside condenser water passages. OR If familiar with electrical appliances

coils, perform the required cleaning by carefully following the maintenance

instructions prevlded with the unit.

There is excessive moisture or heat in the room Use exhaust vent fans while cooking or bathing and try not to use

being cooled (cooking, hot showers, etc.) heat-producing appliances during the hottest part of the day.

The Fan Control is on a Power Saver/Energy Use NORMAL settings for best comfort. When the Power Saver settings

Saver setting, are in use, the fan does not circulate the room air continuously.

The Vent Control is Set to OPEN or EXHAUST. Set the Vent Control to CLOSED for maximum cooling.

The Temperature Control is not at a cool enough Set the Temperature Control to a cooler setting.

setting.

WATER DRIPS FROM THE CABINET INTO THE HOUSE

Check if_ Then...

The unitis not leveledproperly.The unitshould Levelthe air conditioner to providea 1/4"downwardslopetothe outside

slopeslightlydownwardtothe outside. (½ bubbleon carpenter'slevel)toprovideproperdrainage.Repositionor

shimthe cabinetas necessary.DO NOT drilla holeinthe drainpan.

THE AIR CONDITIONER SEEMS TO RUN TOO MUCH

Check if.. Then,.

The currentunitreplaced an older model. The useofmoreefficientcomponentsmay causethe unitto runlonger

thanan oldermodel, butthetotalehergyconsumptionwill beless.Newer

unitsdo notemitthe "blast"of cold air you may be accustomedto from

olderunits,butthis IS NOT an indicationoflessercoolingcapacity or

efficiency.Refertothe efficiencyrating(EER) and capacityrating(in

BTUs)marked onthe unit.

The unitisin a heavilyoccupiedroom or heat- !Useexhaustventfanswhile cookingor bathing.Try notto useheat-

producingappliancesare in use in the room. producingappliancesduringthehottestpart ofthe day, A highercapacity,

unitmay be requireddependingonthe sizeofthe roombeingcooled.

F

TYPICAL AIR CONDITIONER SOUNDS YOU MAY HEAR:

Condenser- You may hear droplets of water hitting

the condenser, causing a "pinging" or "clicking" sound.

Unit Vibration- The unit may vibrate and make noise

because of poor wall or window construction.

Fan- You may hear air movement from the fan.

Compressor- The modem high efficiency compressor may have

a high pitched hum or pulsating noise that cycles on and off.

Thermostat- As the cooling system cycles, the thermostat

may dick.

D/817 TP 5-54- Room Air _ Troubleshool_g Gulde- Revision "A"- March 18, 1996- Page 1 of I

10

Warranty

WARRANTY

Full One-Year Warranty on Air Conditioner

For one year from date of purchase, when this air conditioner isoperated and

maintained for normal room cooling according to instructions in this

owner's manual, Searswill repair it, free of charge, if defective in material or

workmanship.

Full Five-Year Warranty on Sealed Refrigeration System

For five years from the date of purchase, when this air conditioner is operated

and maintained for normal room cooling according to instructions in this

owner's manual, Searswill repair the sealed refrigeration system (consisting of

refrigerant, connecting tubing, and compressor), free of charge, if defective in

material or workmanship.

Warranty Service

Warranty service is available by contacting the nearest service center in the

United States.

This warranty gives you specific legal rights, and you may have other rights

which vary from state to state.

SEARS, ROEBUCK and CO. Dept. 817WA, Hoffman Estates, IL 60719

Sears Service

Maintenancp Agreement

"We Service What We Sell" isour assuranceyou can depend on Sears

for service. Your air conditioner hasadded value when you consider

that Searshas service units nationwide, staffed with professional technicians

trained on all appliancesSears sells. They havethe knowledge and skills, tools,

parts, and equipment to insure our pledge to you that "We Service What We

Sell."

Sears Maintenance Agreement

Maintain the value of your air conditioner with a SearsMaintenance

Agreement. Searsair conditioners are designed, manufactured, and tested for

years of dependable operation. Yet, any modern appliance may require

service from time to time. The Sears Maintenance Agreement offers you an

outstanding service program for your air conditioner.

The Sears Maintenance Agreement

• Isyour way to buy tomorrow's service at today's price.

• Eliminates repair bills resulting from normal use.

• Allows for as many service calls as required.

• Provides an annual Preventive Maintenance Check at your request to

keep your Air Conditioner in proper running condition.

For more information, call 1-800-827-6655

11

For in-home major brand repair service:

Call 24 hoursa day, 7 days a week

1-800-4-MY-HOME sM(1-800-469-4663)

Para pedir servicio de reparaci6n a domicilio - 1-800-676-5811

In Canada for all your service and parts needs call

- 1-800-665-4455

Au Canada pour tout le service ou les pi_ces

For the repair or replacement parts you need:

Call 7 am - 7 pro,7 days a week

1-800-366-PART (1-800-366-7278)

Para ordenar piezas con entrega a domicilio - 1-800-659-7084

For the location of a Sears Parts and Repair Center in your area:

Call 24 hours a day, 7 days a week

1-800-488-1222

For information on purchasing a Sears Maintenance Agreement

or to inquire about an existing Agreement:

Call 9 am - 5 pm, Monday - Saturday

1-800-827-6655

SEARS

HomeCentral"

TheServioeSideofSears"

12

Page is loading ...

Kenmore 25379125991 Owner's manual

Kenmore 25379125991 Owner's manual

in other languages

Related papers

Other documents