GE JCP340 User manual

Type
User manual

This manual is also suitable for

Cooktop
www.geappliances.ca
JCP340
JCP350
Owner’s Manual
Radiant
29-5512 12-05 JR
Safety Instructions . . . . 2–4
Operating Instructions
Cookware Tips . . . . . . . . .6, 7
Dual Surface Unit . . . . . . . .5
Surface Units . . . . . . . . . . . 5
Temperature Limiter . . . . . .7
Care and Cleaning
Control Knobs . . . . . . . . . . 8
Glass Cooktop . . . . . . . . 9, 10
Troubleshooting Tips . . . 11
Consumer Support
Consumer Support . . . . . . 16
Product Registration . .13, 14
Warranty . . . . . . . . . . . . . . 15
Write the model and
serial numbers here:
Model #______________
Serial # ______________
You can find them on
a label under the cooktop.
Cook meat and poultry thoroughly—meat to at least an INTERNAL temperature of 160°F and poultry
to at least an INTERNAL temperature of 180°F. Cooking to these temperatures usually protects against
foodborne illness.
COOK MEAT AND POULTRY THOROUGHLY…
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING!
For your safety, the information in this manual must be followed to minimize the risk of fire or
explosion, electric shock, or to prevent property damage, personal injury, or loss of life.
When using electrical appliances, basic safety precautions should be followed, including
the following:
Use this appliance only for its intended use
as described in this manual.
Do not attempt to repair or replace any
part of your cooktop unless it is specifically
recommended in this manual. All other
servicing should be referred to a qualified
technician.
Before performing any service,
disconnect the cooktop power supply
at the household distribution panel by
removing the fuse or switching off the
circuit breaker.
Be sure your appliance is properly installed
and grounded by a qualified technician in
accordance with the provided installation
instructions.
Have the installer show you the location of
the circuit breaker or fuse. Mark it for easy
reference.
Do not leave children alone—children
should not be left alone or unattended in
an area where an appliance is in use. They
should never be allowed to sit or stand on
any part of the appliance.
Teach children not to play with the
controls or any other part of the cooktop.
Do not allow anyone to climb, stand or
hang on the cooktop.
CAUTION: Items of interest to
children should not be stored in cabinets
above a cooktop—children climbing on the
cooktop to reach items could be seriously
injured.
Always keep combustible wall coverings,
curtains or drapes a safe distance from
your cooktop.
Always keep dish towels, dishcloths, pot
holders and other linens a safe distance
away from your cooktop.
Always keep wooden and plastic utensils
and canned food a safe distance away from
your cooktop.
Never wear loose-fitting or hanging
garments while using the appliance.
Flammable material could be ignited if
brought in contact with hot surface units
and may cause severe burns.
Use only dry pot holders—moist or damp
pot holders on hot surfaces may result in
burns from steam. Do not let pot holders
touch hot surface units. Do not use a towel
or other bulky cloth. Such cloths can catch
fire on a hot surface unit.
For your safety, never use your appliance
for warming or heating the room.
Do not use water on grease fires. Never
pick up a flaming pan. Turn the controls
off. Smother a flaming pan on a surface
unit by covering the pan completely with
well-fitting lid, cookie sheet or flat tray. Use
a multi-purpose dry chemical or foam-type
extinguisher.
Flaming grease outside a pan can be put
out by covering with baking soda or, if
available, by using a multi-purpose dry
chemical or foam-type fire extinguisher.
When flaming foods are under the hood,
turn the fan on.
SAFETY PRECAUTIONS
2
Safety Instructions
Operating Instructions
Care and CleaningTroubleshooting TipsConsumer Support
Safety Instructions
Operating Instructions Care and Cleaning
Troubleshooting Tips Consumer Support
3
www.geappliances.ca
Do not let cooking grease or other
flammable materials accumulate on the
cooktop.
Do not touch surface units. These surfaces
may be hot enough to burn even though
they are dark in color. During and after
use, do not touch, or let clothing or other
flammable materials contact the surface
units or areas nearby the surface units;
allow sufficient time for cooling first.
Potentially hot surfaces include the
cooktop and areas facing the cooktop.
To minimize the possibility of burns,
ignition of flammable materials and
spillage, the handle of a container should
be turned toward the center of the
cooktop without extending over any
nearby surface units.
Always turn the surface unit control to off
before removing the cookware.
Use proper pan size—select cookware
having flat bottoms large enough to cover
the surface unit heating element. The use
of undersized cookware will expose a
portion of the surface unit to direct
contact and may result in ignition of
clothing. Proper relationship of cookware
to burner will also improve efficiency.
Never leave surface units unattended at
high heat settings. Boilovers cause smoking
and greasy spillovers that may catch on fire.
Only certain types of glass, glass/ceramic,
earthenware or other glazed containers are
suitable for cooktop cooking; others may
break because of the sudden change in
temperature.
Keep an eye on foods being fried at high
or medium-high heat settings.
Foods for frying should be as dry as
possible. Frost on frozen foods or moisture
on fresh foods can cause hot fat to bubble
up and over the sides of the pan.
Use little fat for effective shallow or deep-
fat frying. Filling the pan too full of fat can
cause spillovers when food is added.
If a combination of oils or fats will be used
in frying, stir together before heating, or as
fats melt slowly.
Always heat fat slowly and watch as it heats.
Use a deep fat thermometer whenever
possible to prevent overheating fat beyond
the smoking point.
Never try to move a pan of hot fat,
especially a deep fat fryer. Wait until the fat
is cool.
Do not store flammable materials near
the cooktop.
Keep the hood and grease filters clean to
maintain good venting and to avoid grease
fires.
Do not store or use combustible materials,
gasoline or other flammable vapors and
liquids in the vicinity of this or any
appliance.
Clean only parts listed in this Owner’s
Manual.
Do not leave paper products, cooking
utensils or food on the cooktop when not
in use.
Keep cooktop clean and free of
accumulation of grease or spillovers
which may ignite.
Never heat unopened food containers.
Pressure buildup may make container
burst and cause injury.
Never leave jars or cans of fat drippings
on or near your cooktop.
WARNING!
SAFETY PRECAUTIONS
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
Use care when touching the cooktop. The glass surface of the cooktop will retain heat after the
controls have been turned off.
RADIANT SURFACE UNITS
Avoid scratching the glass cooktop.
The cooktop can be scratched with items
such as sharp instruments, rings or other
jewelry and rivets on clothing.
Never use the glass cooktop surface as a
cutting board.
Do not place or store items on top of the
glass cooktop surface when it is not in use.
Be careful when placing spoons or other
stirring utensils on glass cooktop surface
when it is in use. They may become hot
and could cause burns.
Avoid heating an empty pan. Doing so may
damage the cooktop and the pan.
Do not allow water, other liquids or grease
to remain on the cooktop or control
panel.
To minimize the possibility of burns, always
be certain that the controls for all surface
units are at the off position and the entire
glass surface is cool before attempting to
clean the cooktop.
Do not operate the glass surface units if
the glass is broken. Spillovers or cleaning
solution may penetrate a broken cooktop
and create a risk of electrical shock.
Contact a qualified technician immediately
should your glass cooktop become broken.
Do not flame foods on the cooktop. If you do
flame foods under the hood, turn the fan on.
Clean the cooktop with caution. If a wet
sponge or cloth is used to wipe spills on a
hot surface unit, be careful to avoid steam
burns. Some cleansers can produce
noxious fumes if applied to a hot surface.
NOTE: We recommend that you avoid
wiping any surface unit areas until they
have cooled and the indicator light has
gone off. Sugar spills are the exception to
this. Please see the Cleaning the Glass
Cooktop section.
When the cooktop is cool, use only
CERAMA BRYTE
®
Ceramic Cooktop
Cleaner and the CERAMA BRYTE
®
Cleaning Pad to clean the cooktop.
To avoid possible damage to the cooking
surface, do not apply the cleaning cream
to the glass surface when it is hot.
After cleaning, use a dry cloth or paper
towel to remove all the cleaning cream
residue.
Read and follow all instructions and
warnings on the cleaning cream labels.
Large scratches or impacts to cooktops can
lead to broken or shattered glass.
4
Safety Instructions
Operating Instructions
Care and CleaningTroubleshooting TipsConsumer Support
5
Throughout this manual, features and appearance may vary from your model.
How to Set
Push the knob in and turn in either
direction to the setting you want.
At both OFF and HI the control clicks
into position. You may hear slight
clicking sounds during cooking,
indicating the control is keeping the
power level you set.
The control must be pushed in to set
only from the OFF position. When the
control is in any position other than OFF,
it may be rotated without pushing it in.
The UNIT ON indicator light will glow
when any surface unit is on.
Be sure you turn the control knob to OFF
when you finish cooking.
Cooktop temperatures increase with the
number of surface units that are on. With
3 or 4 units turned on, surface
temperatures are high so be careful when
touching the cooktop.
A HOT SURFACE indicator light will glow
when any radiant element is turned on
and will remain on until the surface is
cooled to approximately 150°F.
NOTE:
It comes on when the unit is hot to the touch.
It stays on even after the unit is turned off.
It glows brightly until the unit is cooled to
approximately 150°F.
Never cook directly on the glass.
Always use cookware.
About the radiant surface units…
The radiant cooktop features heating
units beneath a smooth glass surface.
NOTE: A slight odor is normal when a new
cooktop is used for the first time. It is caused by
the heating of new parts and insulating materials
and will disappear in a short time.
The surface unit will cycle on and off to
maintain your selected control setting.
It is safe to place hot cookware from the
oven or surface on the glass cooktop
when the surface is cool.
Even after the surface units are turned
off, the glass cooktop retains enough
heat to continue cooking. To avoid
overcooking, remove pans from the
surface units when the food is cooked.
Avoid placing anything on the surface
unit until it has cooled completely.
Water stains (mineral deposits) are removable
using the cleaning cream or full strength white
vinegar.
Use of window cleaner may leave an
iridescent film on the cooktop. The cleaning
cream will remove this discoloration.
Don’t store heavy items above the cooktop. If
they drop onto the cooktop, they can cause
damage.
Do not use the surface as a cutting board.
Do not slide
cookware across
the cooktop
because it can
scratch the
glass—
the glass is
scratch-resistant,
not scratchproof.
DRAGGING
SURFACE
COOKING
The right front surface unit has 2
cooking sizes to select from so you
can match the size of the unit to the
size of the cookware you are using.
Dual Surface Unit Knob (on some models)
To use the large (9-inch) surface unit,
turn the COIL SELECT knob clockwise to
. Push in and turn the control knob to
the desired setting. The unit will heat the
entire area contained by the larger circle.
To use the small (6-inch) surface
unit, turn the COIL SELECT knob
counterclockwise to . Push in and
turn the control knob to the desired
setting. The unit will only heat the area
inside the smaller circle.
OFF CENTER
Always place the pan in the center of
the surface unit you are cooking on.
Safety Instructions
Operating Instructions Care and Cleaning
Troubleshooting Tips Consumer Support
Using the surface units.
www.geappliances.ca
Selecting types of cookware.
The following information will help you choose cookware which will give good performance on glass cooktops.
Stainless Steel:
recommended
Aluminum:
heavyweight recommended
Good conductivity. Aluminum residues
sometimes appear as scratches on the
cooktop but can be removed if cleaned
immediately. Because of its low melting
point, thin weight aluminum should not
be used.
Copper Bottom:
recommended
Copper may leave residues which can
appear as scratches. The residues can be
removed, as long as the cooktop is
cleaned immediately. However, do not let
these pots boil dry. Overheated metal can
bond to glass cooktops. An overheated
copper bottom pot will leave a residue
that will permanently stain the cooktop if
not removed immediately.
Porcelain Enamel-Covered Cast Iron:
recommended
As long as the cookware is covered
completely with porcelain enamel, this
cookware is recommended. Caution is
recommended for cast iron cookware
that is not completely covered with
smooth porcelain enamel, since it may
scratch the glass ceramic cooktop.
Glass-Ceramic:
usable, but not recommended
Poor performance. May scratch the
surface.
Stoneware:
usable, but not recommended
Poor performance. May scratch the
surface.
Check pans for flat bottoms by
using a straight edge.
Pans with rounded, curved, ridged
or warped bottoms are not
recommended.
6
Safety Instructions
Operating Instructions
Care and CleaningTroubleshooting TipsConsumer Support
For Best Results
Place only dry pans on the surface
units. Do not place lids on the
surface units, particularly wet lids.
Do not use woks that have support
rings. This type of wok will not heat
on glass surface units.
We recommend that you use only a
flat-bottomed wok. They are available
at your local retail store. The bottom
of the wok should have the same
diameter as the surface unit to
ensure proper contact.
Some special cooking procedures
require specific cookware such as
pressure cookers, deep fat fryers, etc.
All cookware must have flat bottoms
and be the correct size.
Do not place wet pans
on the glass cooktop.
Do not use woks with support
rings on the glass cooktop.
Use flat-bottomed woks
on the glass cooktop.
7
Safety Instructions
Operating Instructions Care and Cleaning
Troubleshooting Tips Consumer Support
www.geappliances.ca
Temperature Limiter
Every radiant surface unit has a
temperature limiter.
The temperature limiter protects the
glass cooktop from getting too hot.
The temperature limiter may cycle the
units off for a time if:
The pan boils dry.
The pan bottom is not flat.
The pan is off-center.
There is no pan on the unit.
Note: Flat-bottomed canners are
required for glass cooktops.
Pots that extend beyond 1 inch
of the surface unit’s circle are not
recommended for most surface
cooking. However, when canning
with water-bath or pressure canner,
larger-diameter pots may be used. This
is because boiling water temperatures
(even under pressure) are not harmful
to the cooktop surfaces surrounding
the surface units.
HOWEVER, DO NOT USE LARGE
DIAMETER CANNERS OR OTHER
LARGE DIAMETER POTS FOR
FRYING OR BOILING FOODS
OTHER THAN WATER. Most syrup or
sauce mixtures—and all types of
frying—cook at temperatures much
higher than boiling water. Such
temperatures could eventually harm
the glass cooktop surfaces.
Be sure the canner fits over the
center of the surface unit. If your
cooktop or its location does not
allow the canner to be centered
on the surface unit, use smaller
diameter pots for good canning
results.
Flat-bottomed canners must be
used. Do not use canners with
flanged or rippled bottoms (often
found in enamelware) because
they don’t make enough contact
with the surface units and take a
long time to boil water.
When canning, use recipes and
procedures from reputable
sources. Reliable recipes and
procedures are available from the
manufacturer of your canner;
manufacturers of glass jars for
canning, such as Ball and Kerr
brand; and the United States
Department of Agriculture
Extension Service.
Remember that canning is a
process that generates large
amounts of steam. To avoid burns
from steam or heat, be careful
when canning.
NOTE: If your house has low voltage,
canning may take longer than expected,
even though directions have been
carefully followed. The process time will
be shortened by:
(1) using a pressure canner, and
( 2) starting with HOT tap water for fastest
heating of large quantities of water.
CAUTION:
Safe canning requires that harmful
microorganisms are destroyed and that
the jars are sealed completely. When
canning foods in a water-bath canner,
a gentle but steady boil must be
maintained for the required time. When
canning foods in a pressure canner, the
pressure must be maintained for the
required time.
After you have adjusted the controls,
it is very important to make sure the
prescribed boil or pressure levels are
maintained for the required time.
Since you must make sure to process
the canning jars for the prescribed
time, with no interruption in processing
time, do not can on any cooktop
surface unit if your canner is not flat.
Observe the Following Points in Canning
Wrong!
Right!
8
Care and cleaning of the cooktop.
Be sure electrical power is off and all surfaces are cool before cleaning any part of the cooktop.
Control Knobs
The control knobs may be removed for easier
cleaning.
Make sure the knobs are in the OFF
positions and pull them straight off the
stems for cleaning.
The knobs can be cleaned in a
dishwasher or they may also be washed
with soap and water. Make sure the insides
of the knobs are dry before replacing.
Replace the knobs in the OFF position
to ensure proper placement.
Clear groove
Spring
clip
Molded rib
How to Remove Protective Shipping Film and Packaging Tape
Carefully grasp a corner of the protective
shipping film with your fingers and slowly
peel it from the appliance surface. Do
not use any sharp items to remove the
film. Remove all of the film before using
the appliance for the first time.
To assure no damage is done to the
finish of the product, the safest way to
remove the adhesive from packaging tape
on new appliances is an application of a
household liquid dishwashing detergent.
Apply with a soft cloth and allow to soak.
NOTE: The adhesive must be removed from all
parts. It cannot be removed if it is baked on.
Stem
Safety Instructions
Operating Instructions
Care and CleaningTroubleshooting TipsConsumer Support
9
Safety Instructions
Operating Instructions Care and Cleaning
Troubleshooting Tips Consumer Support
Cleaning the glass cooktop. www.geappliances.ca
Allow the cooktop to cool.
Use a single-edge razor blade
scraper at approximately a 45°
angle against the glass surface
and scrape the soil. It will be
necessary to apply pressure to
the razor scraper in order to
remove the residue.
After scraping with the razor
scraper, spread a few drops of
CERAMA BRYTE
®
Ceramic
Cooktop Cleaner on the entire
burned residue area. Use the
CERAMA BRYTE
®
Cleaning Pad to
remove any remaining residue.
For additional protection,
after all residue has been
removed, polish the entire
surface with CERAMA BRYTE
®
Ceramic Cooktop Cleaner
and a paper towel.
Burned-On Residue
WARNING: DAMAGE to your glass surface
may occur if you use scrub pads other than the
pad included with your cooktop.
Allow the cooktop to cool.
Spread a few drops of CERAMA
BRYTE
®
Ceramic Cooktop Cleaner
on the entire burned residue area.
Using the included CERAMA
BRYTE
®
Cleaning Pad for Ceramic
Cooktops, rub the residue area,
applying pressure as needed.
If any residue remains, repeat the
steps listed above as needed.
For additional protection, after all
residue has been removed, polish
the entire surface with CERAMA
BRYTE
®
Ceramic Cooktop Cleaner
and a paper towel.
The CERAMA BRYTE
®
Ceramic
Cooktop Scraper and all
recommended supplies are
available through our Parts Center.
See instructions under “To Order
Parts” section on next page.
NOTE: Do not use a dull or
nicked blade.
Heavy, Burned-On Residue
Use a CERAMA BRYTE
®
Cleaning
Pad for Ceramic Cooktops or a
Scotch-Brite
®
Multi-Purpose No
Scratch blue scrub pad.
Normal Daily Use Cleaning
ONLY use CERAMA BRYTE
®
Ceramic
Cooktop Cleaner on the glass cooktop.
Other creams may not be as effective.
To maintain and protect the surface of
your glass cooktop, follow these steps:
Before using the cooktop for the
first time, clean it with CERAMA
BRYTE
®
Ceramic Cooktop Cleaner.
This helps protect the top and
makes cleanup easier.
Daily use of CERAMA BRYTE
®
Ceramic Cooktop Cleaner will help
keep the cooktop looking new.
Shake the cleaning cream well.
Apply a few drops of CERAMA
BRYTE
®
Ceramic Cooktop Cleaner
directly to the cooktop.
Use a paper towel or CERAMA
BRYTE
®
Cleaning Pad for Ceramic
Cooktops to clean the entire
cooktop surface.
Use a dry cloth or paper towel
to remove all cleaning residue.
No need to rinse.
NOTE: It is very important that you DO NOT
heat the cooktop until it has been cleaned
thoroughly.
Clean your cooktop after
each spill. Use CERAMA
BRYTE
®
Ceramic Cooktop
Cleaner.
10
Safety Instructions
Operating Instructions
Care and CleaningTroubleshooting TipsConsumer Support
Cleaning the glass cooktop.
To order CERAMA BRYTE
®
Ceramic
Cooktop Cleaner and the cooktop
scraper, please call our toll-free number:
National Parts Center 800.626.2002.
CERAMA BRYTE
®
Ceramic
Cooktop Cleaner . . . . . . . . . . .# WX10X300
CERAMA BRYTE
®
Ceramic
Cooktop Scraper . . . . . . . . . . .# WX10X0302
Kit . . . . . . . . . . . . . . . . . . . . . . . .# WB64X5027
(Kit includes cream and cooktop scraper)
CERAMA BRYTE
®
Cleaning Pads for
Ceramic Cooktops . . . . . . . . .# WX10X350
Turn off all surface units. Remove
hot pans.
Wearing an oven mitt:
a. Use a single-edge razor blade
scraper (CERAMA BRYTE
®
Ceramic Cooktop Scraper) to
move the spill to a cool area on
the cooktop.
b. Remove the spill with
paper towels.
Any remaining spillover should be
left until the surface of the cooktop
has cooled.
Don’t use the surface units again
until all of the residue has been
completely removed.
NOTE: If pitting or indentation in the glass
surface has already occurred, the cooktop glass
will have to be replaced. In this case, service will
be necessary.
Damage from Sugary Spills and Melted Plastic
Our testing shows that if
you are cooking high sugar
mixtures such as jelly or fudge
and have a spillover, it can
cause permanent damage to
the glass surface unless the
spillover is immediately
removed.
Be careful not to slide pots and pans
across your cooktop. It will leave
metal markings on the cooktop
surface.
These marks are removable using
the CERAMA BRYTE
®
Ceramic
Cooktop Cleaner with the CERAMA
BRYTE
®
Cleaning Pad for Ceramic
Cooktops.
If pots with a thin overlay of
aluminum or copper are allowed
to boil dry, the overlay may leave
black discoloration on the cooktop.
This should be removed
immediately before heating
again or the discoloration may
be permanent.
WARNING: Carefully check the bottom of pans
for roughness that would scratch the cooktop.
Metal Marks and Scratches
To Order Parts
Glass surface—potential for permanent damage.
To clean the cooktop seal around the
edges of the glass, lay a wet cloth on it for
a few minutes; then wipe clean with
nonabrasive cleaners.
Cooktop Seal
11
Before You Call For Service… www.geappliances.ca
Troubleshooting Tips
Save time and money! Review the chart on this page
first and you may not need to call for service.
Problem Possible Causes What To Do
Surface units will not Improper cookware Use pans which are absolutely flat and match
maintain a rolling boil being used. the diameter of the surface unit selected.
or cooking is not
fast enough
Surface units do A fuse in your home may be Replace the fuse or reset the circuit breaker.
not work properly blown or the circuit breaker
tripped.
Cooktop controls Check to see the correct control is set for the surface
improperly set. unit you are using.
Scratches (may appear Incorrect cleaning Scratches are not removable. Tiny scratches will become
as cracks) on cooktop methods being used. less visible in time as a result of cleaning.
glass surface
Cookware with rough bottoms To avoid scratches, use the recommended cleaning
being used or coarse particles procedures. Make sure bottoms of cookware are clean
(salt or sand) were between before use, and use cookware with smooth bottoms.
the cookware and the surface
of the cooktop.
Cookware has been slid
across the cooktop surface.
Areas of discoloration Food spillovers not cleaned See the Cleaning the glass cooktop section.
on the cooktop before next use.
Hot surface on a model This is normal. The surface may appear discolored
with a white glass cooktop. when it is hot. This is temporary and will disappear
as the glass cools.
Plastic melted to Hot cooktop came into See the Glass surface—potential for permanent damage
the surface contact with plastic placed section in the Cleaning the glass cooktop section.
on the hot cooktop.
Pitting (or indentation) Hot sugar mixture spilled Call a qualified technician for replacement.
of the cooktop on the cooktop.
Frequent cycling Improper cookware Use only flat cookware to minimize cycling.
off and on of being used.
surface units
Safety Instructions
Operating Instructions Care and Cleaning
Troubleshooting Tips Consumer Support
12
Notes.
Safety Instructions
Operating Instructions
Care and CleaningTroubleshooting TipsConsumer Support
15
Safety Instructions
Operating Instructions Care and Cleaning
Troubleshooting Tips Consumer Support
Electric Cooktop Warranty.
For The Period Of: Camco Will Replace:
One Year Any part of the oven which fails due to a defect in materials or workmanship.
From the date of the During this limited one-year warranty, we will also provide, free of charge, all labor
original purchase and related service to replace the defective part.
Service trips to your home to teach you how to
use the product.
Improper installation, delivery or maintenance.
Failure of the product if it is abused, misused,
or used for other than the intended purpose or
used commercially.
Damage to the glass cooktop (if included) caused by
use of cleaners other than the recommended cleaning
creams.
Damage to the glass cooktop (if included) caused by
hardened spills of sugary materials or melted plastic
that are not cleaned according to the directions in the
Owner’s Manual.
Replacement of house fuses or resetting of circuit
breakers.
Damage to the product caused by accident, fire, floods
or acts of God.
Incidental or consequential damage caused by possible
defects with this appliance.
Damage caused after delivery.
Product not accessible to provide required service.
What Camco Will Not Cover:
This warranty is extended to the original purchaser and any succeeding owner for products purchased for
ordinary home use in Canada. In-home warranty service will be provided in areas where it is available and deemed
reasonable by Camco to provide.
Some provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above
exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights
which vary from province to province. To know what your legal rights are in your province, consult your local or
provincial consumer affairs office.
Warrantor: Camco Inc.,
Burlington, Ontario
All warranty service provided by our Factory Service
Centers, or an authorized Customer Care
®
technician.
To schedule service, on-line, 24 hours a day, visit us
at www.geappliances.ca, or call 1.800.361.3400. Please
have serial number and model number available when
calling for service.
Staple your receipt here.
Proof of the original purchase
date is needed to obtain service
under the warranty.
EXCLUSION OF IMPLIED WARRANTIES—Your sole and exclusive remedy is product repair as provided
in this Limited Warranty. Any implied warranties, including the implied warranties of merchantability
or fitness for a particular purpose, are limited to one year or the shortest period allowed by law.
15
16
Printed in the United States
GE Appliances Website www.GEAppliances.ca
Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day,
any day of the year! For greater convenience and faster service, you can now download Owner’s Manuals
on-line. You can also “Ask Our Team of Experts
” your questions, and so much more...
Schedule Service www.GEAppliances.ca
Expert GE repair service is only one step away from your door. Call 1.800.361.3400, 24 hours a day,
7 days a week.
Parts and Accessories www.GEAppliances.ca
To inquire about purchasing a part or an accessory for your appliance, call our National Parts Center
at 1.800.661.1616.
Contact Us www.GEAppliances.ca
If you are not satisfied with the service you receive from GE, contact us on our Website with all the details
including your phone number, or write to: Camco, Inc.
1 Factory Lane
Moncton, New Brunswick
E1C 9M3
Register Your Appliance www.GEAppliances.ca
Register your new appliance on-line—at your convenience! Timely product registration will allow for
enhanced communication and prompt service under the terms of your warranty, should the need arise.
You may also mail in the preprinted registration card included in the packing material.
Consumer Support.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

GE JCP340 User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages