1
INSTRUCTION MANUAL
5LT Chandelier
Towne Collection
Home Depot SKU 480-997 (UPC 899089002094)
2
Thank you for purchasing this Hampton Bay interior chandelier. This product has been manufactured with the highest standards of
safety and quality.
FEATURES:
1. Five-light interior chandelier in brushed nickel finish with fabric shades. This chandelier is a part of the matching Towne
Collection and is available online at www.homedepot.com or through special order at your local Home Depot store.
2. Standard 72-inch wire and 60-inch chain for open entry-way, dining room, and cathedral ceiling installations. Also includes
a Quick Link to easily adjust length of chain.
3. This fixture has been engineered to safely use up to five 60 watt MAX, candelabra based (B10.5), incandescent light bulbs
(not included).
4. Can be used with any standard 120 volt incandescent style dimmer switch (not included).
QUESTIONS, PROBLEMS, MISSING PARTS:
Before returning to your local Home Depot, please call our Customer Service Team at 1-877-527-0313 or visit
www.homedepot.com. Please reference your SKU 480-997 or UPC 899089002094.
CAUTION:
1. Before starting installation of this fixture or removal of a previous fixture, disconnect the power by turning off the circuit
breaker or by removing the fuse at the fuse box.
2. CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY ELECTRICAL QUESTIONS.
3. If you have any non-electrical questions about this fixture, please contact our Customer Service team at 1-877-527-0313 or
visit www.homedepot.com. Please reference your SKU 480-997 or UPC 899089002094.
4. Keep your receipt and these Instructions for Proof of Purchase.
TOOLS REQUIRED FOR ASSEMBLY & INSTALLATION(not included):
5 Light Bulbs Safety goggles Ladder Gloves Wire strippers
(60 watt Candelabra
Light Bulbs)
Flathead screwdriver Phillips screwdriver Electrical tape Pliers
PARTS INCLUDED FOR ASSEMBLY (parts are not to scale):
1ea Canopy 1ea Screw Collar 60 in. (152.4 cm) 1ea Loop Ring 1ea Threaded 5ea Shades (#14)
(#11) Loop (#12) Chain (#15) (#13) Nipple (#9)
1ea Quick Link 2ea Outlet Box Screws 1ea Hex Nut 1ea Ground Screw 1ea Mounting Strap 3ea Wire Connectors
(#3) (#10) (#7) (#5) (#4) (#2)
3
ASSEMBLY INSTRUCTIONS:
1. Carefully unpack the fixture. Lay out all parts on a clean surface.
2. Screw the middle column (#16) to the fixture (#19). Using the Quick Link (#14), attach the chain (#15) to the middle column
(#16).
3. Thread the fixture wires up through the middle column (#16), weave the wire through every third link of the chain (#15),
through the loop ring (#13), through the screw collar loop (#12), through the canopy (#11) and through the threaded nipple (#9)
on the mounting strap (#4).
4. Install five 60 watt candelabra (B10.5) base incandescent light Bulbs (#18).
5. Place the Shades (#18) with clip.
ASSEMBLY:
INSTALLATION INSTRUCTIONS:
1. Attach the Mounting Strap (#4) to the Outlet Box (#1) using the two outlet box Screws (#10).
2. Adjust the chain (#15) to required height by lifting the fixture and attaching the Quick Link (#14) to a link of chain (#15)
closer to the ceiling. The fixture can be raised and lowered in this manner until the desired height is achieved. Next, use pliers
to twist open (cover the chain with cloth to prevent damage) the first unused link of chain (#15). Remove and save the excess
chain. Pull the excess fixture wires through the nipple (#9) into the outlet box (#1). Wires may be left at full length or
shortened depending on how much space you have in the outlet box (#1).
3. Wrap the ground wire from the fixture around the Ground Screw (#5) on the Mounting Strap (#4), and then connect the ground
wire from the fixture to the ground wire from the Outlet Box (#1). Connect the wire without writing on it (with raised ribs)
from the fixture to the white wire (neutral wire) from the Outlet Box (#1). Connect the wire with writing on it (smooth wire)
from the fixture to the black wire (live wire) from the outlet box (#1). Cover the connections using the wire connectors (#2).
Wrap the wire connections/connectors (#2) with electrical tape to ensure the connections will not come apart. Position the
wires back inside the outlet box (#1). Note: If you have electrical questions, consult your local electrical code for approved
grounding methods or seek the advice of a qualified licensed electrician.
4. Place the canopy (#11) over the nipple (#9) all the way to the ceiling. Screw the loop ring (#13) onto the screw collar loop
(#10) until the Canopy (#11) is held firmly against the ceiling.
5. Installation is now complete. Turn on the power at the circuit breaker or fuse box. Turn the light switch on to activate the
fixture.
60W Candelabra Bulb (B10.5)
Loop
#11 Canopy
#12 Screw Collar
Loop
#13 Loop Ring
Loop
#15 Chain
Loop
Lamp Distribution
(bottom view)
Loop
#3 Quick Link
Loop
#16 Middle Column
Loop
#14 Shade
Loop
Bulb Socket
Loop
#19 Fixture
Loop
4
INSTALLATION:
TROUBLESHOOTING:
PRODUCT MAINTENANCE:
1. To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the
glass and surface of the fixture.
2. To clean the inside of the fixture, first disconnect power to the fixture by turning off the circuit breaker or by removing the
fuse at the fuse box. Next, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the inside
glass and interior surface of the fixture.
3. Do not use any cleaners with chemicals, solvents or harsh abrasives. Use only a dry soft cloth to dust or wipe carefully.
LIMITED WARRANTY
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of five (5) years
from date of purchase. This warranty applies only to the original consumer purchaser and only to products used in normal use and
service. If this product is found to be defective, the manufacturer’s only obligation, and your exclusive remedy, is the repair or
replacement of the product at the manufacturer’s discretion, provided that the product has not been damaged through misuse, abuse,
accident, modifications, alterations, neglect or mishandling. This warranty shall not apply to any product that is found to have been
improperly installed, set-up, or used in any way not in accordance with the instructions supplied with the product. This warranty
shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence, alteration, or faulty installation, or
any other failure not relating to faulty material or workmanship. This warranty shall not apply to the finish on any portion of the
product, such as surface and/or weathering, as this is considered normal wear and tear. The manufacturer does not warrant and
specially disclaims any warranty, whether express or implied, of fitness for a particular purpose, other than the warranty contained
herein. The manufacturer specifically disclaims any liability and shall not be liable for any consequential or incidental loss or
damage, including but not limited to any labor / expense costs involved in the replacement or repair of said product.
Problem
Possible Cause
Corrective Action
Light Bulb will not illuminate.
1. Light bulb is burned out.
1. Replace light bulb.
2. Power is off.
2. Make sure
power supply is on.
3. Faulty wire connection.
3. Check wiring.
4. Faulty switch.
4. Test or replace switch.
Fuse blows or circuit breaker trips
when light bulb is illuminated.
Crossed wires or power wire is grounding
out.
Check wire connections.
#1 Outlet Box
Smooth Fixture
Wire to Black
Supply Wire
#3 Ground Wire
Ribbed Fixture Wire to
White Neutral Wire
#7 Hex Nut
#4 Mounting Strap
#5 Ground Screw
Outlet Box Screw
Fixture Wire
#11 Canopy
#13 Loop Ring
#15 Chain
Outlet Box Screw
#9 Threaded Nipple
Threaded Nipple top
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
