Kompernass PFBS 9.6V User manual

Page is loading ...

5 GB

Introduction

For your safety ..............................................................................................................Page 6

Proper use .....................................................................................................................Page 6

Features and equipment ...............................................................................................Page 6

Included items ...............................................................................................................Page 7

Technical information ...................................................................................................Page 7

Safety

Safety advice ...............................................................................................................Page 7

Operation

Charging the battery pack ..........................................................................................Page 8

Inserting / removing the battery pack into / out of the drill / grinder ........................Page 9

Changing a collet .........................................................................................................Page 9

Inserting / changing tools .............................................................................................Page 9

Switching on and oﬀ / Setting the speed range .........................................................Page 9

Advice on working with materials / Tools / Speed ranges ........................................Page 9

Tips and tricks ...............................................................................................................Page 11

Maintenance and cleaning

Maintenance .................................................................................................................Page 11

Cleaning ........................................................................................................................Page 11

Disposal ......................................................................................................................Page 11

Information

Service ...........................................................................................................................Page 11

Manufacturer’s Declaration of Conformity / Manufacturer ......................................Page 11

Table of content

6 GB

Multi-purpose precision

rotary tool PFBS 9.6

Q

 Introduction

Q

For your safety

Please make sure you familiarise your-

self fully with the way the device works

before you use it for the ﬁrst time and

that you understand how to handle electrical power

tools correctly. Further details can be found in the

operating instructions. In addition to the above, you

must also observe the general safety advice con-

tained in the accompanying booklet. Keep these

instructions in a safe place. If you pass the device

on to anyone else, please ensure that you also pass

on all the documentation.

Q

Proper use

The multi-purpose precision rotary tool is intended

to be used for drilling, milling, engraving, polishing,

cleaning, grinding, cutting and sawing wood, metal,

plastic, ceramics or stone in dry environments. Any

other use or modiﬁcation to the drill / grinder shall

be considered as improper use and could give rise

to considerable dangers. The manufacturer will not

accept liability for loss or damage arising from

improper use. Not intended for commercial use.

Q

Features and equipment

Multi-purpose precision rotary tool:

1

On / Oﬀ switch / Rotational speed control

2

Battery pack release button

3

Battery pack

4

Metal stirrup hanger

5

Clamping nut

Introduction

The following icons / symbols are used in this instruction manual:

Read instruction manual!

W

Watts (Eﬀective power)

Observe caution and safety notes!

Wear protective gloves and safety goggles

Caution – electric shock!

Dangerous electric current – danger to life!

Safety class II

Ah

Amp-hours (Battery capacity)

Proper procedure and handling.

n

0

Rated idle running speed

Keep children and other unauthorised personnel

at a safe distance when using electrical tools.

Direct current

(Current and kind of tension)

Damaged appliances, power cables and power

plugs mean potentially fatal risks from electric

shock. Regularly check the condition of the appli-

ance, the power cables and the power plugs.

V

~

Voltage

Dispose packaging and appliance in an

environmentally-friendly way!

7 GB

6

Spigot nut

7

Spindle lock

Battery charger (see Fig. A):

8

Charging cradle with connector

9

Mains adapter

10

LED

Accessories (see Fig. B):

11

6 HSS drills

12

2 Mandrels for mounting tools

13

3 Polishing wheels

14

4 Grinding wheels

15

1 Metal brush

16

1 Saw blade

17

10 Cutting wheels

18

4 Collets

19

2 Plastic brushes

20

3 Milling bits

21

2 Engraving bits

22

5 Grinding bits

23

Combination tool

Q

Included items

1 Multi-purpose precision rotary tool

with rechargeable battery pack

1 Battery charger

1 Plastic case

1 Accessory kit (44-piece)

1 Operating instructions

1 Booklet “Guarantee and service”

1 Booklet “General safety advice”

Q

Technical information

Model PFBS 9.6:

Rated voltage: 9.6 V DC

No-load speed: n

0

5000 - 25 000 min

-1

Max. disc ø: 25 mm

Rechargeable battery pack PFBS 9.6-2:

Rated voltage: 9.6 V DC

Capacity: 1000 mAh NI-MH

Battery charger PFBS 9.6-1:

Primary:

Rated voltage: 230 V

~

50 Hz

Rated output: 8.5 W

Secondary:

Rated voltage: 12 V DC

Charging current: 400 mA

Charging duration: approx. 3 hours

Protection class: II / &

Noise and Vibration Informationen:

Determined noise level with A evaluation.

Sound pressure level: 61 dB (A)

Acoustic power level: 75 dB (A)

Evaluated acceleration, typical.

Hand-arm vibration: 2,63 m / s

2

Q

 Safety

Safety advice

J Ensure that the drill / grinder is always used in

accordance with the advice in these operating

instructions and only by persons over 16 years

of age.

J

Keep children away from the drill /

grinder. Store the drill / grinder

indoors in an enclosed, dry place

where it cannot be reached by children.

Introduction / Safety

8 GB

To avoid danger to life from

electric shock:

J

A damaged drill / grinder, mains

lead or plug presents a serious dan-

ger to life from electric shock. Check

the condition of the drill / grinder, charger, mains

lead, mains plug and battery pack at frequent

intervals. Do not use a drill / grinder with dam-

aged parts. If a dangerous situation arises pull

out the mains plug from the socket immediately.

Never open up the

drill / grinder or equipment.

Always have any repairs

carried out or replace-

ment parts ﬁtted at the service

centre or by an

electrical equipment repair specialist.

J Protect the charger, battery pack and the drill /

grinder from moisture.

J Warning! Do not use the drill / grinder with

chargers or batteries other than the charger /

battery pack supplied.

J Warning! Never short circuit the battery

pack. Overheating, ﬁre or destruction of the

battery pack may result.

Therefore:

- Do not connect any wires to the battery

pack poles.

- Take care that no metal objects (nails,

screws,

etc.) can short circuit the battery pack

connectors.

J m Attention! Never throw the battery pack

into ﬁre or water. Danger of explosion! Handle

the battery pack with care, protect it from im-

pacts and sharp blows!

Attention! To avoid the danger

of injury, burning and damage

to health:

J Warning! If you come into contact with the

acid from the battery pack, wash oﬀ the acid

thoroughly with water immediately. If acid

should enter your eyes, ﬂush them immediately

with water and ﬁnd a doctor immediately.

J

Caution! The tool continues to

rotate after it has been switched oﬀ!

Avoid contact with rapidly rotating

drill / grinder components.

J When you use the drill / grinder wear

the following protective equipment:

safety glasses and protective gloves.

To work safely:

J

Before cleaning or maintaining the charger or

battery

pack always pull the plug out of the

mains socket.

J Never charge the battery pack if the ambient

temperature is below 10 °C or above 40 °C.

m Attention! To avoid damaging the tool or

workpiece.

J Do not allow the tool to come to a standstill by

overloading it!

Q

 Operation

Q

Charging the battery pack

m Attention! A battery pack that has been

unused for a while or never been charged must be

charged before reuse or ﬁrst use. The battery pack

requires about 3-5 cycles before it can reach its

full charge.

m

Attention!

Always pull out the mains plug

(

mains adapter

9

) before you

insert the battery

pack into or take it out of the charger.

j Connect the adapter

9

to a mains socket.

j Insert the battery pack

3

into the charging

cradle

8

. Make sure that the polarity of the

battery pack matches that of charging cradle

8

.

j The LED

10

lights up green whenever the bat-

tery pack

3

is in the charging cradle

8

and

the adapter

9

is connected to a mains socket.

J Do not use the quick-charge process to charge

a battery pack for a second time in close suc-

cession. Otherwise there is the danger that the

battery pack will become overcharged and its

useful life and that of the charger reduced.

Safety / Operation

9 GB

J Switch the charger oﬀ for at least 15 minutes

between successive charging processes. To do

this pull the mains plug

(

mains adapter

9

)

out

of the socket.

Q

Inserting / removing the

battery pack into / out of the

drill / grinder

Inserting the battery pack:

j Set the On / Oﬀ switch

1

to position “0”.

j Insert the battery pack

3

into the drill / grinder

until it engages.

Removing the battery pack:

j Pressing the battery pack buttons

2

at the

sides at the same time allows you to remove

the battery pack

3

.

Q

Changing a collet

j Press the spindle lock

7

and keep it pressed.

j Rotate the clamping nut

5

until the lock

engages.

j Release the clamping nut

5

from the thread

and remove the collet

18

.

j Insert the correct collet

18

and screw it tight

with the clamping nut

5

.

j Release the spindle lock

7

.

Q

Inserting / changing tools

j Press the spindle lock

7

and keep it pressed.

j Rotate the clamping nut

5

until the lock

engages.

j Release the clamping nut

5

using the open

spanner end

of the combination tool

23

.

j If a tool is already inserted remove it.

j First insert the tool you wish to use though the

clamping nut

5

before you insert it into the

collet

18

.

j Press the spindle lock

7

and keep it pressed.

j

Insert the collet

18

into the threaded insert and

screw

the clamping nut

5

tightly on the thread

using the

open spanner end of the

combination tool

23

.

Note: Use the screwdriver end of the

combination tool

23

to release or tighten the

screw of the mandrels

12

.

Q

Switching on and oﬀ / Setting

the speed range

Switching on / Setting the speed range:

j Set the On / Oﬀ switch

1

to a position

between “2” and “10”.

Switching oﬀ:

j Set the On / Oﬀ switch

1

to position “0”.

Q

Advice on working with

materials / Tools / Speed ranges

j Make sure that no debris from working the

material adheres to the tool. Use paraﬃn, cut-

ting oil or similar medium to lubricate the tool.

j Use the highest speed when working on steel

or iron with the milling bits.

j Use a short trial on a test piece to determine the

optimum rotational speed range for working on

zinc, zinc alloy, aluminium, copper and lead.

j Use the low speed range for working on plas-

tics and low-melting point materials.

j Use high speeds on wood.

j Use the medium speed range for cleaning,

polishing and buﬃng.

The following information shall be considered as

recommendatory only. Learn by practical experi-

ence which tools and settings are the best for the

materials you work with.

Operation

10 GB

Operation

Setting the appropriate speed

Symbols on

On / off

switch

1

Material

0

(Drill / grinder switched oﬀ)

6

Softwood, metal

2

Plastics and low melting

point materials

8

Hardwood

4

Stone, Ceramics

10

Steel

Examples of appropriate tool selection Function

Function Accessory Application

Drilling

HSS drill

11

Drilling wood (see Fig. C)

Milling

Milling bits

20

Various tasks, e.g. hollowing out, gouging,

shaping, grooving or slotting

Engraving

Engraving bits

21

Markings (see Fig. D)

Polishing,

derusting

mAttention!

Use only the lightest

contact pressure of

the tool on the work-

piece.

Metal brush

15

Derusting (see Fig. E)

Polishing wheel

13

Working on various metals and plastics, in

particular noble metals like gold or silver

(see Fig. F)

Cleaning

Plastic brush

19

E.g. cleaning complex plastic housings or the

area around a door lock

Metal brush

15

E.g. cleaning cutlery, jewellery, tools (see Fig. E)

(The metal brush is softer than steel)

Grinding

Grinding wheels

14

,

grinding bits

22

Grinding of stone, precise tasks on hard materials,

such as ceramics or alloy steel (see Fig. G)

Cutting and

sawing

Cutting discs

17

Cutting metal, plastic or wood (see Fig. H)

Saw blade

16

Saw blade Sawing steel, metal, wood or plastic

(see Fig. I)

11

GB

Q

Tips and tricks

If you use press too hard you run the risk of break-

ing the tool or damaging the workpiece. You will

achieve the best results by operating the tool at a

constant rotational speed and using a low contact

pressure on the workpiece.

Q

 Maintenance and cleaning

Q

Maintenance

j Before and after a prolonged period of

non-use fully charge the battery pack

3

.

Q

Cleaning

j Clean all the dirt oﬀ the drill / grinder. Use a

dry cloth for cleaning.

Q

 Disposal

The packaging is wholly composed of

environmentally-friendly materials that can

be disposed of at a local recycling centre.

Do not dispose of electric tools in

the household waste!

In accordance with European Directive

2002 / 96 / EC about waste electrical and elec-

tronic equipment and its transposition into national

legislation, worn out electric tools must be collected

separately and taken for environmentally compatible

recycling.

Faulty or used rechargeable batteries must be recy-

cled in accordance with Directive 91 / 157 / EEC.

Return the appliance with integrated rechargeable

battery via the available collection facilities.

Contact your local refuse disposal authority for

more details of how to dispose of your eletric tools.

Q

 Information

Q

Service

Please see the warranty documents for details of

the Service Oﬃce responsible for your country.

Q

Manufacturer’s Declaration of

Conformity / Manufacturer

We, Kompernaß GmbH, Burgstr. 21,

D-44867 Bochum, Germany, declare that this

product complies with the following EU directives:

Machinery Directive (98 / 37 / EC)

EU Low Voltage Directive (2006 / 95 / EC)

Electromagnetic compatibility

(89 / 336 / EEC), (92 / 31 / EEC)

Type / Device description:

Multi-purpose precision rotary tool PFBS 9.6

Bochum, 31.10.2007

Hans Kompernaß

- Managing Director -

We reserve the right to make technical modiﬁcations in the course

of further development.

Operation / Maintenance and cleaning / Disposal / Information

Page is loading ...

Kompernass PFBS 9.6V User manual

Kompernass PFBS 9.6V User manual

in other languages

Related papers

Other documents