2. Metra Electronics
  3. 95-7366B
95-7366B

Metra Electronics 95-7366B User manual

  • Hello! I am an AI chatbot trained to assist you with the Metra Electronics 95-7366B User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • How do I prepare the kit?
    How do I assemble the kit?
    What tools are required?
    What are the features of the kit?
    What are the components of the kit?
    What is the purpose of the product?
METRA. The World’s best kits.
™
metraonline.com
© COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION
REV. 9/21/2015 INST95-7366B
Installation instructions for part 95-7366B
CAUTION!
Metra recommends disconnecting the negative bat
-
tery terminal before beginning any installation, unless the vehicle
manufacturer recommends against so. Please check with your local
Dealership for more information. All accessories, switches, climate
controls panels, and especially air bag indicator lights must be con
-
nected before reconnecting the battery or cycling the ignition. Also,
do not remove the factory radio with the key in the on position, or the
vehicle running. It would be best to remove the key from the ignition
and then wait a few seconds before removing the factory radio.
• ISO DDIN radio provision
• Painted scratch resistant black
• A) Radio trim panel • B) Radio brackets
KIT FEATURES
KIT COMPONENTS
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • 70-7304, HYBL-04
Antenna Adapter: • Not required
• Panel removal tool • Phillips screwdriver • 10mm Socket wrench • Cutting tool
TOOLS REQUIRED
Kia Sorento 2016-up
95-7366B
A B
Dash Disassembly ................................................. 2
Kit Preparation ....................................................... 2
Kit Assembly .......................................................... 3
Table of Contents
95-7366B
2
1.
Unclip and remove the factory radio
trim panel including the a/c vents.
(Figure A)
2. Remove (4) Phillips screws
securing the radio and then
remove. (Figure B)
Continue to kit preparation
Dash Disassembly
(Figure B)
(Figure A)
1. Cut the marked area in the
dash cavity. (Figure A)
2. Remove (1) 10mm nut holding the
area previously cut in step 1 to
remove the cut-out area.
Continue to kit assembly
Kit Preparation
(Figure A)
95-7366B
Kit Assembly
3
(Figure A)
ISO DDIN radio provision
1. Attach the radio brackets to the
radio using the screws supplied
with the radio. (Figure A)
2.
Locate the factory wiring harness
and antenna plug in the dash and
make all necessary connections to
the radio. Metra recommends using
the proper mating adapters from
Metra and/or AXXESS. Re-connect
the negative battery terminal and
test the radio for proper operation.
3. Secure the completed assembly
into the sub-dash using the factory
hardware.
4. Snap the 7366 radio trim panel
into the factory trim panel, and
then reassemble the dash in
reverse order of disassembly.
METRA. The World’s best kits.
™
metraonline.com
© COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION
REV. 9/21/2015 INST95-7366B
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certified technicians
Installation instructions for part 95-7366B
IMPORTANT
If you are having difficulties with the
installation of this product, please call our
Tech Support line at 1-800-253-TECH.
Before doing so, look over the instructions a
second time, and make sure the installation
was performed exactly as the instructions
are stated. Please have the vehicle apart
and ready to perform troubleshooting steps
before calling.
Page is loading ...
Page is loading ...
Page is loading ...
METRA. The World’s best kits.
™
metraonline.com
© COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION
REV. 9/21/2015 INST95-7366B
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recomienda técnicos
con certificación del Programa
de Certificación en Electrónica
Móvil (Mobile Electronics
Certification Program, MECP).
EL CONOCIMIENTO ES PODER
Mejore sus habilidades de instalación y
fabricación inscribiéndose en la escuela de
dispositivos electrónicos móviles más reconocida
y respetada de nuestra industria. Regístrese en
www.installerinstitute.com o llame al
800-354-6782 para obtener más información y
avance hacia un futuro mejor.
Instrucciones de instalación para la pieza 95-7366B
IMPORTANTE
Si tiene dificultades con la instalación
de este producto, llame a nuestra línea
de soporte técnico al 1-800-253-TECH.
Antes de hacerlo, revise las instrucciones
por segunda vez y asegúrese de que la
instalación se haya realizado exactamente
como se indica en las instrucciones. Por
favor tenga el vehículo desarmado y listo
para ejecutar los pasos de resolución de
problemas antes de llamar.
/