Husqvarna 125E-CANADA Owner's manual

Brand: Husqvarna

Model: 125E-CANADA

Type: Owner's manual

This manual is also suitable for

125E

EN Operator's manual, pp. 2-23

P_easeread these instructions and make sure yau understand them before using the machine

FR Manuel d'utilisation, pp. 24-48 12 5 E

Life attendvemen_ e_ bi_n ass_miler le manueF d'udlis_ion aYan_d'u_iliser Is machine.

ES Manual de instrucciones, pp. 49-73

Le_ deten_damente el manual de _nstrucclones y asegOrese de entender su eonten_do antes de udlizar la

maquma EN FR ES

CONTENTS

Contents

CONTENTS

Contents ........................ 2

Note the following before starting .... 2

KEY TO SYMBOLS

Symbols ......................... 3

SAFETY INSTRUCTIONS

Personal protective equipment ...... 4

Machine's safety equipment ........ 4

Cutting equipment ................. 5

Checking, maintaining and servicing

the machine's safety equipment ..... 5

General safety precautions ......... 8

Starting ......................... 9

Fuel safety ....................... 9

Transporting and storage ........... 9

General working instructions ........ 9

Basic safety rules ................. 9

Basic working techniques .......... 10

KNOW YOUR EDGER

Know your edger .................. 12

ASSEMBLY

Assembling the loop handle ......... 13

Assembling the blade .............. 13

FUEL HANDLING

Fuel ............................ 14

Fuelh_g .......................... 14

STARTING AND STOPPING

Check before starting .............. 15

Starting and stopping .............. 15

MAINTENANCE

Carburetor ....................... 17

Muffler .......................... 17

Spark plug ....................... 18

Air filter .......................... 18

Bevel gear ....................... 18

Adjusting the edger's cutting depth 19

Maintenance schedule ............. 19

TECHNICAL DATA

Technical data .................... 20

WARRANTY STATEMENT ......... 21

EMISSION CONTROL

WARRANTY STATEMENT ......... 22

Note the following before

starting:

Husqvarna AB has a policy of continuous

product development and therefore

reserves the right to modify the design and

appearance of products without prior

notice. Long-term exposure to noise can

result in permanent hearing impairment.

Always use approved hearing protection.

Maintenance, replacement, or repair of the

emission control devices and system may

be performed by any nonroad engine re-

pair establishment or individual.

The Emissions Compliance Period referred

to on the Emissions Compliance label indi-

cates the number of operating hours for

which the engine has been shown to meet

Federal emissions requirements.

Category C = 50 hours, B= 125 hours, and

A = 300 hours.

41 I il I 81 I

/k WARNING

The engine exhaustfromthis product

containschemicalsknownto the State

of Californiato cause cancer,birth

defectsor otherreproductiveharm.

For reference, please fill out the following

information that will be needed for future

servicing of your trimmer:

Model Number:

Serial Number:

Purchase Date:

Purchased From:

WARNING: An edger can be

dangerous if used incorrectly or

carelessly, and can cause serious

or fatal injury to the operator or

others. It is extremely important

that you read and understand the

contents of this operator's manual.

WARNING: Under circum-

stances may the design of the

machine be modified without the

permission of the manufacturer.

Always use genuine accessories.

Non-authorized modifications

and/or accessories can result

in serious personal injury or the

death of the operator or others.

Your warranty may not cover

damage or liability caused by the

use of non-authorized accesso-

ries or replacement parts.

KEY TO SYMBOLS

Symbols

WARNING: This edger can be

dangerous! Careless or incorrect

.Z_K

use can result in serious or fatal

injury to the operator or others.

Please read the operator's manual

carefully and make sure you r[]I ri-]

understand the instructions

before using the machine.

Always wear: _)

• A protective helmet where there

is a risk of falling objects

• Hearing protection

• Approved eye protection

Max. speed of output shaft, rpm

msx

10000 rpm

Watch out for thrown objects

and ricochets.

Warning for rotating blade.

Keep hands and feet clear.

WARNING: The blade continues to A

rotate even after the engine has _.=_,

stopped. /_{_

When the engine has stopped, m

stop the blade from rotating

by tetting the blade come in

contact with the ground.

Indicates the direction of rotation.

The operator of the machine must ensure

that no persons or animals comes within a

50 feet (t5 meters) radius while working.

[t .4;1

mAk

Arrows which show limits for _l_4P,

handle positioning. 'V|

Always wear approved protective

gloves.

Wear sturdy, non-slip boots.

Other symbols/decals on the machine

refer to special certification requirements

for certain markets.

Stop the engine by pushing

and holding the stop switch

in the STOP position until the

engine stops before carrying

out any checks or maintenance.

Regular cleaning is required.

Visual check.

Approved eye protection must

always be used.

SAFETY INSTRUCTIONS

Personal protective equipment

IMPORTANT! Whenever you use a lawn

edger, you must wear personal protective

equipment that is approved by the authori-

ties. Personal protective equipmeet does

not eliminate the risk of accidents, but it

can reduce the effects of an injury in the

event of an accident. Ask your dealer for

help when choosing protective equipment.

WARNING: Listen out for warn-

ing signals or shouts when you are

wearing hearing protection. Always

remove your hearing protection as

soon as the engine stops.

GLOVES

Gloves should be worn whee necessary,

e.g., when fitting cutting attachments.

HEARING PROTECTION

Wear hearing protection that provides

adequate noise reduction.

EYE PROTECTION

Always wear approved eye protection, if

you use a visor thee you must also wear

approved protective goggles. Approved

protective goggles must comply with

standard ANSI Z87.1.

BOOTS

Wear sturdy, non-slip boots.

CLOTHING

Wear clothes made of a strong fabric and

avoid loose clothing that can catch on

twigs and branches. Always wear heavy.

long pants. Do not wear jewelry, shorts

sandals or go barefoot. Secure hair so it is

above shoulder level.

FIRST AID KIT

Always have a first aid kit nearby.

Machine's safety equipment

This section describes the machine's safe-

ty equipment, its purpose, and how checks

and maintenance should be carried out to

ensure that it operates correctly. See the

"Know your trimmer" section to locate

where this equipment is positioned on your

machine.

The life span of the machine can be reduced

and the risk of accidents can increase if

machine maintenance is not carried out

correctly and if service and/or repairs are not

carded out professionally, if you need further

ieformation please contact your nearest ser-

vicing dealer.

_lb WARNING: Never use a machine

that has faulty safety equipment!

Carry out the inspection, mainte-

nance and service routines listed in

this section.

Throttle lock

The throttle lock is desigeed to prevent ac-

cidental operation of the throttle control.

When you press the lock (A) (i.e. when you

grasp the handle) it releases the throttle

control (B). When you release the handle

the throttle contro_ and the throttle lock both

move back to their original positions. This

movement is controlted by two independent

return springs. This arrangement means

that the throttle control is automatically

locked at the idle setting.

Stop switch

Make sure the engine stops when you push

and hold the stop switch.

SAFETY INSTRUCTIONS

Cutting attachment guard

This guard is intended to prevent loose ob-

jects from being thrown towards the opera-

tor. The guard also protects the operator

from accidental contact with the cutting at-

tachment.

_ ARNING: Never use a cutting

attachment without an approved

guard. See the section on "Technical

data". If an incorrect or faulty guard

is fitted this can cause serious

personal injury.

WARNING: Overexposure to

vibration can lead to circulatory

damage or nerve damage in people

who have impaired circulation.

Contact your doctor if you experi-

ence symptoms of overexposure to

vibration. Such symptoms include

numbness, loss of feeling, tingling,

pricking, pain, loss of strength,

changes in skin color or condition.

These symptoms normally appear

in the fingers, hands or wrists. The

risk increases at low temperatures.

Muffler

The muffler is designed to reduce the noise

level and to direct the exhaust gases away

from the operator.

CAUTION! Muffler is fitted with a catalytic

converter designed to reduce harmfui ex-

haust gases.

For mufflers, it is very important that you fot-

low the instructions on checking, maintain-

ing, and servicing your machine.

See Checking, maintaining and servicing the

machine's safety equipment section.

WARNING: Mufflers fitted with

catalytic converters get very hot

during use and remain so for some

time after stopping. This also ap-

plies at idle speed. Contact can re-

sult in burns to the skin. Remember

the risk of fire!

_lb WARNING: The inside of the

muffler contain chemicals that may

be carcinogenic. Avoid contact with

these elements in the event of a

damaged muffler.

WARNING: Bear in mind that:

Engine exhaust fumes contain car-

bon monoxide, which can cause

carbon monoxide poisoning. For

this reason you should not start or

run the machine indoors, or any-

where that is poorly ventilated.

The exhaust fumes from the engine

are hot and may contain sparks

which can start a fire. Never start

the machine indoors or near com-

bustible material!

Cutting equipment

The blade is designed

and processed to

withstand loads that

edging of a lawn

involves.

The locking nut /'__. _ _'_

secures the cutting _ -;_Y_ "%.>

_tqu ioPur_peu_ts__aft _,_11_ v

Checking, maintaining and

servicing the machine's

safety equipment

IMPORTANT!

All servicing and repair work on the machine

requires special training. This is especially

true of the machine's safety equipment. If

your machine fails any of the checks de-

scribed below you must contact your service

agent. When you buy any of our products we

guarantee the availability of professional re-

pairs and service. If the retailer who sells

your machine is not a servicing dealer, ask

him for the address of your nearest service

agent.

SAFETY INSTRUCTIONS

Throttle lock

• Make sure the throttle contro_ is locked

at the idle setting when the throttle lock

is released.

• Press the throttle lock and make sure it

returns to its original position when you

release it.

• Check that the throttle control and

throttle lock move freely and that the

return springs work properly.

• See instructions under the section

"Start". Start the machine and apply full

throttle. Release the throttle and check

that the cutting attachment stops and re-

mains at a standstill. If the cutting attach-

ment rotates with the throttle in the idle

position then the carburetor idle setting

must be checked. See instructions under

the section "Maintenance".

Stop switch

• Start the engh_e and make sure the engine

stops when you push and hold the stop

switch.

Cutting attachment guard

• Ensure that the guard is undamaged and

is not cracked.

• Replace the guard if it has been exposed

to impact or is cracked.

• Always use the recommended blade and

guard combination. See section on "Tech-

nical data".

Muffler

• Never use a machine that has a faulty

muffler.

• Regularly check that the muffler is securely

attached to the machine.

• The muffler on this unit is equipped with a

special spark arrestor mesh. The mesh

should be checked and, if necessary.

cleaned by a servicing dealer. A blocked

mesh will cause the machine to overheat,

which can lead to serious damage. Never

use a muffler with a defective spark arres-

tor mesh. See the Maintenance section.

SAFETY INSTRUCTIONS

Cutting equipment

This section describes how to choose and

maintain your cutting equipment in order to:

• Obtain maximum cutting performance.

• Extend the life of cutting equipment.

General rules:

1. Only use the blade and guard we recom-

mend! See the section on "Technical

Data".

2. Check the blade for damage. A damaged

blade should always be replaced.

,_ WARNING: Never use a machine

with faulty safety equipment. The

machine's safety equipment must be

checked and maintained as

described in this section.

If your machine fails any of these

checks contact your service agent to

get it repaired.

Locking nut

• Protect your hand from injury during as-

sembly. Always wear protective gloves.

Use the blade guard as protection when

tightening nut. Tighten the nut by turning

against the direction of rotation. Loosen

the nut by turning in the direction of rota-

tion. (NOTE: The nut has a left-handed

thread.)

• Tighten the nut securely using a wrench.

Loosen Tighten

NOTE!

The locking nut's nylon lock must not be

worn so that it can be turned by hand. The

nut should be replaced after it has been

removed and reinstalled approximately 10

times.

_ WARNING: Always stop the en-

gine before doing any work on the

cutting attachment. This continues

to rotate even after the throttle has

been released. Ensure that the

cutting attachment has stopped

completely and disconnect the HT

lead from the spark plug before

you start to work on it,

SAFETY INSTRUCTIONS

General safety precautions

IMPORTANT!

• The machine is only designed for cutting

the edges of lawns.

• The only accessories you can operate

with this engine unit are the cutting at-

tachments we recommend in the "Tech-

nical data" section,

• Never use the machine if you are tired, if

you have drunk alcohol, or if you are tak-

ing medication that could affect your vi-

sion, your judgment or your coordination,

• Never use the machine in extreme weath-

er conditions such as severe cold, very hot

and/or humid climates.

• Never use a machine that has been modi-

fied in any way from its original specifica-

tion,

• Wear bersonai protective equipment. See

instructions in the "Personal protective

equipment" section.

• Never use a machine that is faulty, Carry

out the checks, maintenance and service

instructions described in this manual.

Some maintenance and service measures

must be carried out by trained and quali-

fied specialists. See instructions in the

"Maintenance" section.

• All covers and guards must be fitted before

starting, Make sure the spark plug cap and

HT lead are not damaged. Otherwise you

could get an electric shock.

• The machine operator must ensure that

no people or animals come closer than

50 feet (15 meters) while working.

• Secure hair above shoulder length. Se-

cure or remove loose clothing or clothing

with loosely hanging ties, straps, tassels,

etc, They can be caught in moving parts.

• Being fully covered also helps protect you

from debris and pieces of toxic plants

thrown by spinning blade.

• Keep handles free of oil and fuel,

• Always keep the engine on the right hand

side of your body,

• Hold the unit firmly with both hands.

• Keep blade below waist level and away

from all parts of your body. Do not raise

engine above your waist.

• Keep all parts of your body away from

muffler and spinning blade, Keep engine

below waist level, A hot muffler can cause

serious burns.

• Keep firm footing and balance. Do not

overreach or use from unstable surfaces

such as ladders, trees, steep slopes, roof-

tops, etc,

• Use only in daylight or good artificial light.

• Use only for jobs explained in this manual,

WARNING: Faulty cutting

equipment may increase the risk

of accidents.

Personal protection

• Always wear boots and

other equipment described

in the "Personal protective J

equipment" section.

• Always wear working

clothes and heavy-duty

long pants.

• Never wear loose fitting

clothes or jewelry.

• Persons with tong hair

should (for personal safety)

put their hair up.

Safety instructions regarding the

surroundings

• Never allow children to use the machine,

• Ensure no one comes closer than 50 feet

(15 meters) when working,

• Never allow anyone else to use the

machine without first ensuring that they

have understood the contents of the

operator's manual.

Safety instructions before starting

work

• Inspect the working area. Remove any

objects such as stones, broken glass,

nails, steel wire, string, etc. that can be

thrown or can wrap around the blade or

blade guard.

• Keep others at a safe distance. Children,

animals, onlookers and helpers should

stand outside of the safety zone of 50

feet (15 meters), Stop the machine im-

mediately if anyone should approach.

• Keep in mind that the operator is respon-

sible for accidents or hazards occurring

to other people or their property,

• Check the entire machine before starting

work, Replace damaged parts, Check for

fuel leakage and that all safety guards

and covers are complete and fastened

securely. Check all nuts and bolts.

• Check the blade for

cracks or any other

damage.

SAFETY INSTRUCTIONS

• Ensure the blade guard t -_-_ _..._-.

is mounted and not _i -.._ ._j '_J

damaged. =_

• Check that the btade and blade guard are

correctly secured.

• When adjusting the carburetor, make sure

the blade is held against the ground and

that no one is in the immediate vicinity.

• Make sure the blade does not rotate when

idling.

• Make sure the handle and safety features

are in order. Never use a machine that has

parts missing or has been changed in

relation to the specification.

• Only use the machine for the purpose for

which it was intended.

Starting

_i WARNING: When the engine is

started with the choke in either the

choke or start throttle positions the

blade will start to rotate immediately.

• Ensure that all of the engine covers and

housings are propedy fitted before the unit

is started.

• Never start or attempt to run the unit with

the clutch, clutch drum, clutch cover, or

driveshaft removed.

• Never start the machine indoors. Exhaust

fumes can be dangerous if inhaled.

• Observe your surroundings and make sure

that there is no risk of people or animals

coming into contact with the cutting equip-

ment.

• See the "Starting and Stopping" section for

complete instructions.

Fuel safety

• Always use a fuel container with an anti-

spill valve.

• Never refuel the machine while the engine

is running.

• Always stop the engine and let it cool for a

few minutes before refueling.

• Make sure there is plenty of ventilation

when refueling or mixing fuel (gasoline and

2-stroke oil).

• Move the machine at least 10 feet (3 me-

ters) from the refueling point before start-

ing it.

Mh_. 1Oft.

_ (3 m)

• Never start the machine:

• if you have spilled fuel on it. Wipe off

the spillage and allow remaining fuel to

evaporate.

• if you have spilled fuel on yourself or

your clothes, change your clothes. Wash

any part of your body that has come in

contact with fuel. Use soap and water.

• if the machine is leaking fuel Check reg-

ularly for leaks from the fuel cap and fuel

lines.

• Avoid all skin contact with fuel. Fuel is a

skin irritant and may even cause skin

changes.

_L WARNING: Take care when ban- I

dling fuel. Bear in mind the risk of

fire, explosion and inhaling fumes.

Transporting and storage

• Store and transport the machine and fuel

so that there is no risk of any leakage or

fumes coming into contact with sparks or

naked flames, for example, from electricai

machinery, electric motors, electrical re-

iays/switches or boilers.

• When storing and transporting fuel always

use approved containers intended for this

purpose.

• When storing the machine for long periods

the fuel tank must be emptied. Contact

your local gas station to find out where to

dispose of excess fuel.

• The engine must be cool before storage or

transporting.

General working instructions

IMPORTANT!

This section describes the basic safety

_recautions for working with the edger.

If you encounter a situation where you are

uncertain how to proceed you shouid ask an

expert. Contact your servicing dealer.

Avoid all usage which you consider to be

beyond your capability,

SAFETY INSTRUCTIONS

Basic safety rules

/ Q00

1. Observe your surroundings:

• To ensure that peopte, animals or other

things cannot affect your control of the

machine.

• To ensure that people, animals, etc., do

not come into contact with the blade or

loose objects that are thrown out by the

blade.

CAUTIONt Do not use the machine un-

less you are able to call for help in the

event of an accident.

2. Do not use the machine in bad weather,

such as dense fog, heavy rain, strong

wind, intense cold, etc. Working in bad

weather is tiring and often brings added

risks, such as icy ground, unpredictable

felling direction, etc.

3. Make sure you can move and stand safely.

Check the area around you for possible ob-

stacles (roots. rocks, branches, ditches,

etc.) in case you have to move suddenly.

Take great care when working on sloping

ground.

4. Switch off the engine before moving to

another area.

5. Never put the machine down with the en-

gine running.

Basic working techniques

Safety instructions while working

• Always ensure you have a safe and firm

foothold.

• Always hold the machine with both hands.

Hold the machine on the right-hand side

your the body.

• Make sure your hands and feet do not

come into contact with the blade when the

engine is running.

• When the engine is switched off, keep your

hands and feet away from the blade until it

has stopped.

• Always cut edges at fuli throttle.

• Always keep the blade close to the

ground.

• Always drop to idling speed after each

working operation. Longer periods run-

ning at full throttle without loading the en-

gine (that is without resistance, which the

engine feels from the blade when edging)

can lead to serious engine damage.

• It is recommended that the engine not

be operated for longer than 1 minute at

full throttle.

• Be especially careful when pulling the

edger towards you during work.

• Walk, never run.

• if heavy vibrations occur, stop the engine.

Remove the spark plug cable from the

spark plug. Check that the machine is not

damaged. Repair any damage.

SAFETY INSTRUCTIONS

&WARNING: Sometimes grass and

stones can collect in the blade guard

and around the blade. Always stop

the engine when cleaning.

WARNING: Beware of thrown

objects. Always wear eye protec-

tion. Never lean over the blade

guard. Stones rubbish etc. can be

thrown up into the eyes resulting in

blindness or other serious injury.

Keep unauthorised persons at a

distance. Children, animals, on-

lookers and helpers should be out-

side the safety zone of 15 meters

(50 feet). Stop the machine immedi-

ately if anyone approaches.

The bevel gear unit can get hot dur-

ing use and may remain so for a

while afterwards. There is a risk of

slight burns if you touch it.

Safety instructions after complet-

ing work

• Ensure the blade has stopped before

cleaning, makh_g repairs or an inspection.

Remove the spark plug cable from the

spark plug.

• Wear heavy-duty gloves when making

repairs to the edger.

• Store the machine out of reach of chil-

dren.

• Only use origina_ spare parts during re-

pair.

KNOW YOUR EDGER

Know your edger

1. Blade 12. Fuel tank

2. Grease filler cap 13. Choke control

3. Bevel gear 14. Primer bulb

4. Blade guard 15. Air filter cover

5. Shaft 16. Handle adjustment

6. Loop handle 17. Locking nut

7. Throttle control 18. Flat washer

8. Stop switch 19. Spring washer

9. Throttle lock 20. Depth adjustment knob

10. Cylinder cover 21. 2-stroke engine oil

11. Starter handle 22. Operator's manual (EPA)

ASSEMBLY

NOTE: Make sure unit is assembled cor-

rectly as shown in this manual.

Assembling the loop handle

• Position the handle on the shaft. Note

that the handle must be mounted be-

tween the two arrows on the shaft.

• Fit the screw, secl;i_ng plate a'hd wing

nut as shown in the diagram.

• Tighten the wing nut.

Assembling the blade

_ ARNING: The blade will contin-

ue to spin after the engine stops or

after the throttle trigger has been re-

leased. To avoid serious injury,

make sure the blade has stopped

coasting and disconnect the spark

plug before performing work on the

blade.

_ ARNING: Wear protective

gloves when handling or performing

maintenance on the blade to avoid

injury. The blade is sharp and can

cut you even when it is not moving.

1. Align hole in the dust cup with the hoIe in

the side of the bevel gear by rotating the

dust cup (A).

2. Insert a small screwdriver into aligned

holes. This will keep the output shaft from

turning while loosening the locking nut (E).

3. While holding the screwdriver in position,

remove locking nut by turning clockwise.

4. Remove both washers (C and D) and

the blade (B) from the output shaft.

5. Install blade onto output shaft.

6. Reinstall both washers and locking nut

(counterclockwise).

7. Tighten locking nut firmly with a wrench

while hoiding screwdriver in position.

8. Remove the screwdriver.

9. Turn blade by hand. If the blade binds

against the shield, or appears to be un-

even, the blade is not centered, and

you must reinstall.

WARNING: Under no circum-

stances should the edger be used

without the blade guard installed.

FUEL HANDLING

Fuel mixture

CAUTION! The machine is equipped with

a two-stroke engine and must always be

run using a mixture of gasoline and two-

stroke engine oil, It is important to accu-

rately measure the amount of oil to be

mixed to ensure that the correct mixture is

obtained. When mixing small amounts of

fuel, even small inaccuracies can drastical-

ly affect the ratio of the mixture.

&WARNING: Always ensure

there is adequate ventilation when

handling fuel.

Gasoline

CAUTION! Always use high quality

unleaded gasoline.

• This engine is certified to operate on

unleaded gasoline.

• The lowest recommended octane rating

is 87. If you run the engine on lower oc-

tane rating than 87, "knocking" can oc-

cur, This leads to an increased engine

temperature, which can result in a seri-

ous engh_e breakdown,

• When working at continuous high revs a

higher octane rating is recommended,

Two-stroke oil

• For great results and performance use

HUSQVARNA two-stroke oil, which is

specially formulated for our two-stroke

engh_es, Mixture 1:50 (2%),

• To maximize the life of your trimmer, you

may choose to use a high quality syn-

thetic oil formulated for two-stroke

engh_es, Mixture 1:50 (2%),

• Never use two-stroke oil intended for

water-cooled outboard engines,

sometimes referred to as outboard oil.

• Never use oil h_tended for four-stroke

engh_es.

Two-stroke oil

Gasoline 2% (1:50)

U.S. gallon U.S. fl. oz.

1 2 t/2

2 1/2 6 1/2

5 12 7/8

Mixing

• Always mix the gasoline and oil in a

clean container intended for fuel

• Always start by filing half the amount of the

gasoline to be used. Then add the entire

amount of oil. Mix (shake) the fuel mixture.

Add the remaining amount of gasoline.

• Mix (shake) the fuel mixture thoroughly

before filling the machine's fuel tank.

• Do not mix more than one month's sup-

ply of fuel at a time.

• If the machine is not used for some time,

the fuel tank should be emptied and

cleaned.

WARNING: The catalytic con-

verter muffler gets very hot during

and after use. This also applies

during idling. Be aware of the fire

hazard, especially when working

near flammable substances and/or

vapors.

Fueling

WARNING: Taking the following

precautions, will lessen the risk of

fire:

Do not smoke or place hot objects

near fuel.

Always shut off the engine before

refueling.

Always stop the engine and let it

cool for a few minutes before refu-

elling.

When refueling, open the fuel cap

slowly so that any excess pressure

is released gently.

Tighten the fuel cap carefully after

refueling.

Always move the machine away

from the refueling area before

starting.

• Clean the area around the fuel cap.

Contamination in the tank can cause

operating problems.

• Ensure that the fuel is well mixed by shak-

ing the container before filling the tank.

STARTING AND STOPPING

Check before starting

• Inspect the unit before each use. Re-

place damaged parts. Check for fuel

leaks. Make sure all fasteners are in

place and secure, Make sure the blade

and blade guard are properly installed

and the blade nut is securely tightened,

• Check that the blade and blade guard

are not damaged or cracked, Replace

the blade or blade guard if they have

been exposed to impact or are cracked.

• Never use the machine without a guard

nor with a defective guard,

Starting and stopping

QOO

WARNING: The complete clutch,

clutch cover, and shaft must be

fitted before the machine is started,

otherwise parts could come loose

and cause personal injury.

Always move the machine away

from the refueling area before

starting. Place the machine on a

flat surface. Ensure the cutting at-

tachment caRRot come into contact

with any object.

Make sure no unauthorized persons

are in the working area, otherwise

there is a risk of serious personal

injury. The safety distance is 50 feet

(15 meters).

Cold engine

Primer bulb: Press the primer bulb 10

times until fuel begins to fill the bulb. The

primer bulb need not be completely filled.

Choke: Move the blue engine choke lever

over to the closed position.

_ _t J_r _'_ _

Starting

Hold the body of the machine on the

ground using your Ieft hand (CAUTION!

Not with your foot!),

Firmly grip the starter rope handle with

your right hand. DO NOT squeeze

throttle trigger, Slowly pull out the cord

until you feel some resistance (the starter

pawls grip); then quickly and powerfully

pull the cord.

Never wrap the starter cord around

your hand.

Repeat pulling the cord until the engine

attempts to start, Squeeze throttle trigger

to release the choke. Continue to hold

throttle trigger and pull starter rope until

engine runs,

NOTE: If engine dies, return blue engine

choke lever to the closed position and

repeat starting steps,

CAUTION! Do not pull the starter cord all

the way out and do not let go of the starter

handle when the cord is fully extended.

This can damage the machine.

STARTING AND STOPPING

Warm engine

With a warm engine, squeeze and hold the

throttle trigger, Pull starter rope sharply

while squeezing throttIe trigger until engine

runs.

Stopping

Stop the engine by pushing and holding

the stop switch in the STOP position until

the engine stops.

WARNING: When the engine is I

started with the choke in the closed I

position the cutting attachment will

start to rotate immediate y.

MAINTENANCE

The owner is responsible for the perfor-

mance of all required maintenance as

defined in the operator's manual.

Carburetor

Your Husqvama product has been designed

and manufactured to specifications that re-

duce harmful emissions. After the engine

has used 8-10 tanks of fueI, the engine will

be run-in. To ensure that it continues to run

at peak performance and to minimize harm-

ful exhaust emissions after the run-in peri-

od, ask your servicing dealer to adjust your

carburetor.

_ WARNING: The complete clutch,

clutch cover, and shaft must be I

fitted before the machine is started, I

otherwise parts could come loose

and cause persona injury.

Function

• The carburetor governs the engine's

speed via the throttte control. Air and fuel

are mixed in the carburetor.

• The T-screw regulates the throttle setting

at idle speed. If the T-screw is turned

clockwise this gives a higher idle speed;

turning it counterclockwise gives a lower

idle speed.

Basic setting

• The basic carburetor settings are ad-

justed during testing at the factory. Fine

adjustment should be carried out by a

skilled technician.

CAUTION! If the cutting attachment rotates

when the engine is idling the idle adjustment

screw T should be turned counterclockwise

until the cutting attachment stops.

Rec. idle speed:

See "Technical data" section.

Recommended max. speed:

See "Technical data" section.

The idle speed is correctly adjusted when

the engine will run smoothly in every posi-

tion. The idle speed should also be well

below the speed at which the cutting at-

tachment starts to rotate.

Idle Speed

Screw-T

WARNING: If the idle speed can-

not be adjusted so that the cutting

attachment stops, contact your ser-

vicing dealer. Do not use the ma-

chine until it has been correctly ad-

justed or repaired.

Unit/Maintenance Safety

Disconnect the spark plug before perform-

ing maintenance, except carburetor adjust-

ments.

Muffler

_ WARNING: If the idle speed

cannot be adjusted so that the cut-

ting attachment stops, contact your

dealer/service workshop. Do not use

the machine until it has been cor-

rectly adjusted or repaired.

Fine adjustment of the idle speed-T

Adjust the idle speed using the idle adjust-

ment screw-T if it is necessary to readjust.

First, turn the idle adjustment screw-T

clockwise until the cutting attachment starts

to rotate. Then, turn the screw counterc-

lockwise until the cutting attachment stops.

CAUTION! Muffler is fitted with a catalytic

converter designed to reduce harmful ex-

haust gases.

The muffler is designed to reduce the noise

level and to direct the exhaust gases away

from the operator. The exhaust gases are

hot and can contain sparks, which may

cause fire if directed against dry and com-

bustible material.

Mufflers are equipped with a special spark

arrestor mesh. The mesh should be

checked and, if necessary, cleaned by a

servicing dealer. If the mesh is damaged,

it should be replaced, if the mesh is fre-

quently blocked, this can be a sign that the

3erformance of the catalytic converter is

impaired. Contact your servicing dealer to

inspect the muffler. A blocked mesh will

cause the machine to overheat and result

in damage to the cylinder and piston,

MAINTENANCE

_ Muffler bolts

CAUTION[ Never use a machine that has

a faulty or loose muffler. Ensure the muffler

bolts are tight.

I& ARNING: Mufflers fitted with

catalytic converters get very hot

during use and remain so for some

time after stopping. This also ap-

plies at idle speed. Contact can re-

sult in burns to the skin. Remember

the risk of fire!

WARNING: The inside of the I

muffler contain chemicals that may

be carcinogenic. Avoid contact with

these elements in the event of a

damaged muffler.

WARNING: Bear in mind that:

Engine exhaust fumes contain car-

bon monoxide, which can cause

carbon monoxide poisoning. For

this reason you should not start or

run the machine indoors, or any-

where that is poorly ventilated.

The exhaust fumes from the engine

are hot and may contain sparks

which can start a fire. Never start

the machine indoors or near com-

bustible material!

Spark plug

The spark plug condition is influenced by:

• Incorrect carburetor adjustment.

• An incorrect fuel mixture (too much or in-

correct type of oil).

• A dirty air filter.

These factors cause deposits on the spark

plug electrodes, which may result in operat-

ing problems and starting difficulties.

If the machine is low on power, difficult to

start or runs poorly at idle speed: always

check the spark plug first before taking

any further action. If the spark plug is dirty,

clean it and check that the electrode gap is

0.024" (0.6 mm). The spark plug should be

replaced after about a month in operation or

earlier if necessary.

CAUTION! Always use the recommended

spark plug type! Use of the wrong spark

plug can damage the piston/cylinder.

0.024" (0.6 ram)

Air filter

The air filter must be regularly cleaned to

remove dust and dirt in order to avoid:

• Carburetor malfunctions

• Starting problems

• Loss of engine power

• Unnecessary wear to engine parts

• Excessive fuel consumption

Clean the filter every 25 hours, or more

regularly if conditions are exceptionally

dusty.

Cleaning the air filter

Remove the air filter cover and take out the

filter, Wash it clean in warm. soapy water.

Rinse thoroughly. Ensure that the filter is dry

before refitting it.

An air filter that has been in use for a long

time cannot be cleaned completely. The

filter must therefore be replaced with a new

one at regular intervals. A damaged air

filter must always be replaced.

Bevel gear

The bevel gear is filled with the right quan-

tity of grease at the factory. However, be-

fore using the machine you should check

that the bevel gear is filled three-quarters

full with grease. Use HUSQVARNA special

grease.

MAINTENANCE

The grease in the bevel gear does not nor-

maliy need to be changed except if repairs

are carried out.

Adjusting the edger's cutting

depth

The cutting depth should be adjusted before

starting work.

I_ ARNING: Never attempt to ad-

just the cut depth when the engine

is running. Always release the

throttle trigger, wait until the blade

stops turning, move the ON/OFF

switch to the OFF position, and

disconnect spark plug before mak-

ing adjustments.

A ____

1. Loosen the depth adjustment knob (A).

2. Slide the wheel to the desired position.

• Raising the wheel will increase the cut-

ting depth.

• Lowering the wheel will decrease the

cutting depth.

3. Tighten the depth adjustment knob se-

curely.

_lb WARNING: Always keep the

engine on the right hand side of

your body. Always wear protective

glasses, long pants and heavy-

duty shoes when using the

machine.

Observe your aurrondings, ensure

people and animals do not come in

the immediate vicinity or can be hit

by thrown objects.

When edging, apply full throttle

before entering the soil.

Maintenance schedule

Below you will find some general mainte-

nance instructions.

Daily maintenance

• Check throttle trigger and throttle trigger

lockout function.

• Check that the stop switch works

correctly.

• Check that there are no fuel leaks from

the engine, tank or fuel lines.

• Check that the blade does not rotate

when the engine is idling.

• Clean the outside of the machine.

• Check that the blade guard is not dam-

aged or cracked.

• Replace the blade guard if it is exposed to

impact or is cracked.

• A non-balanced blade induces heavy

vibrations that may damage the machine.

• Check that nuts and screws are tight.

• Check that the screws that hold the bevel

gear are tight.

• Check that the locking nut is tight.

Weekly maintenance

• Check the starter and starter cord.

• Clean the carburetor area.

• Clean the outside of the spark plug. Re-

move it and check the electrode gap. Ad-

just the gap to 0.024" (0.6 mm), or

replace the spark plug. Use resistor spark

plug Champion RCJ-6Y or equivalent.

• Clean the cooling fins on the cylinder and

check that the air intake near the starter

is not blocked.

• Check that the bevel gear is filled with

grease up to 3/4 full. Use special grease.

• Clean the air filter.

Monthly maintenance

• Clean the fue_ tank.

• Clean the outside of the carburetor and

the space around it.

• Clean the fan and the area around it.

• Check fuel lines for cracks or other dam-

age. Change if necessary.

• Change the fuel filter in fuel tank.

• Check the clutch, clutch springs and the

clutch drum for wear. Replace if neces-

sary.

• Check electrical wires and connections.

• Replace the spark plug. Use resistor

spark plug Champion RCJ-6Y or equiva-

lent.

• Change the air filter.

TECHNICAL DATA

Technical data

125E

Engine

Cylinder volume, cu.in./cm 3 1.7/28

Cylinder bore, inch/mm 1.4/35

Stroke, inch/mm 1.t30/28.7

Idle speed, rpm 2,800-3,200

Recommended max. speed, rpm 11,000

Speed of output shaft, rpm 8,000

Max. engine output, acc. to ISO 8893, hp/kW 1.1/0.8

Catalytic converter muffler Yes

Speed-regulated ignition system Yes

Ignition system

Manufacturer/type of ignition system

Spark plug

Electrode gap, inch/mm

Fuel and lubrication system

Manufacturer/type of carburetor Zama

Fuel tank capacity, US pint/liter 0.85/0.4

Weight

Weight without fuel, cutting attachment and guard, Ibs/kg 13.3/6.0

Sound levels

Sound power level, LWA dB(A) 114

Equivalent sound pressure level at the user's ear,

measured according to ANSI B175.3-1997, dB(A),

min/max (see note 1) 94/97

Vibration levels

Vibration levels at handles, measured according to ANSi

B175.3-1997, m/s 2

At idle, left/right handles 3/5

At max. speed, left/right handles 9/8

Walbro/CD

Champion RCJ-6Y

0.024/0.6

Note 1: Equivalent noise pressure level is calculated as the time-weighted energy total for

noise pressure levels under various working conditions with the following time distribution:

1/2 idle and 1/2 max. speed.

NOTE! Noise pressure at the user's ear and vibration on the handles are measured with all

the machine's approved cutting equipment fitted. The table indicates the highest and lowest

values.

Model 125E (M10 LH arbor shaft thread)

Cutting equipment Part. no.

Blade 530053007

Blade guard kit 545044101

Page is loading ...

Husqvarna 125E-CANADA Owner's manual

Brand: Husqvarna

Model: 125E-CANADA

Type: Owner's manual

This manual is also suitable for

125E

Download PDF

report

in other languages

français: Husqvarna 125E-CANADA Le manuel du propriétaire
español: Husqvarna 125E-CANADA El manual del propietario

Husqvarna 125E-CANADA Owner's manual

This manual is also suitable for

Husqvarna 125E-CANADA Owner's manual

in other languages

Related papers

Other documents