IN STAL LA TION
IN STRUC TION
INSTALLATION INSTRUCTIONS FOR
560258
ADJUSTABLE SUPPORT LEG KIT
FORM# 536D-0711
I - SHIPPING AND PACK ING LIST
Package 1 of 1 contains:
2 ea. - Adjustable Support Leg Assembly
6 ea. - Self Tapping Screws
Check contents for shipping damage. Contact the last carrier immediately if any shipping damage is found.
II - AP PLI CA TION
This adjustable support leg kit is constructed of 18 gauge galvanized steel and can be used on any of NORDYNE's
product where equipment stabilization, support of cantilevered loads, or support of add on accessories such as Horizontal
Economizers, Power Exhaust, ERV’s, etc., is required.
:gni nraW
NOTICE:
Read these instructions in their entirety before proceeding with the installation of this accessory kit. Special
attention is required for placement of these supports so damage to internal components of unit and roofing
material is avoided.
This kit is to be installed by a qualified service technician in accordance with these instructions and all codes
having jurisdiction. Failure to follow these instructions could result in serious injury, property damage, or
death. These instructions are primarily intended to assist qualified individuals experienced in the proper
installation of this appliance. Some local codes require licensed installation/service personnel for this type
of equipment.
R6GN-180 Series Shown
This kit can also be used for the
fol low ing ap pli ca tions:
Nordyne Series Roof Curbs Car rier
Downflow Hor i zon tal Se ries
8" 14" 18" 24" 24"
24" w/ Duct
48DP/DR
R6GN-150* Series Gas/Electric units
555617 555618 555619 555620 555631 555632 All
R6GN-180* Series Gas/Electric units
555617 555618 555619 555620 555631 555632 All
Sup port Leg
Front View
NEIES01
July 21, 2011
III - IN STAL LA TION
1. DISCONNECT ALL POWER TO UNIT.
2. To avoid damage to the unit, prior to drilling holes in any cabinet inspect the areas behind where the support legs are to
be located for any wiring, tubing, or electrical items. Remove panels as necessary.
3. Ensure the unit or add on accessory to be supported is level and located in its intended final position.
4. Ensure area beneath support foot is clear of debris such as screws, rocks, etc.. Failure to properly apply the support
legs may cause damage to rubber, tar, or gravel roofing materials that may lead to leaks.
5. Remove the two carriage bolts securing the adjustable support leg assemblies together. Adjust legs to the required
height where support foot rests firmly on the ground or roof. Pass one of the carriage bolts back through the assembly
to ensure bolt holes are re-aligned. Mark
top of support brace location on unit. Slide support legs apart and secure the
rear mounting leg to the unit using supplied self tapping screws through holes provided in the bracket. Add additional
mounting holes if necessary. NOTE: Based on height of roof curb it may be necessary to temporarily remove the
support foot from the leg assembly and slide it down through the top.
6. Repeat Steps 2 through 5 for the other support leg assembly.
7. Replace any panels removed during installation of support legs before operating equipment.
8. Reconnect power back to the unit.
IN STAL LA TION
IN STRUC TION
INSTALLATION INSTRUCTIONS FOR
560258
ADJUSTABLE SUPPORT LEG KIT
Roof Curb
1.50" MAX.
TO SCREW
ENIL RET NEC
1.50" MAX.
TO SCREW
ENIL RET NEC
Roof Line
© Nortek Global HVAC, LLC 2015. All Rights Reserved.
-
1
-
2
Reznor R6GN Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Reznor R6GN Installation guide
-
Reznor R6GN Installation guide
-
-
-
-
-
-
-
-
Other documents
-
Unbranded Roof Curb 150-180, 555617 - 555620 Installation guide
-
-
Greenheck 481745 ERV-10, 20,45 Operating instructions
-
-
-
-
-
Unbranded Horizontal Return Air Panel Kit, 919251 Installation guide
-
-