GE AEH05LMS1 Owner's manual

ge.com

©

0

Safety Instructions . ............ 2, 3

Operating Instructions

Control I_lob Models ........... 6, 7

Touch Pad Models .............. 4, 5

Care and Cleaning

Air Filter ........................ 7

Outdoor Coils .................... 7

Installation Instructions ....... 8-11

Troubleshooting Tips ............ 1'2

Normal Operating Sounds ........ 12

Consumer Support

Consumer Support ....... Back Cover

Ownership Registration fi)r

Customers in Canada only ...... 13, 14

Warranty fbr Customers

in Canada ...................... 16

Warranty fi)r Customers

in the U.S.A ..................... 15

AEH05

AEH 06 *

AEH08*

AES05

Climadseur

La section fran_aise commence ?_la page 17

Acondicionador

de aire

O

*ENERGY STAR ® labeled product

I

ENERGYSTAR

As an ENERGY STAR® partnei; GE has

determined that this product meets

the ENERGYSTAR®guidelines for

energy efficiency.

Writethemodelandserial numbershere:

Model #

Serial #

Find these numbers on a label on the

side of the air conditioneL

In Canada, contact us at:

xs_s_<GEAppliances.ca

La secci6n en espa_,ol empieza en la pdgina 33

49-7604 12-08 JR

IMPORTANTSAFETYINFORMATION.

READALLINSTRUCTIONSBEFOREUSING.

WARNING!

For your safety, the information in this manual must be followed to minimize the risk of fire, electric shock

or personal injury.

SAFETYPRECAUTIONS

}}Use this appliance only f_)r its intended }}

purpose as described in this Owner's

Manual.

iii}i}i

iii}i}}li_

iiiH}}ii{_

This air conditioner must be properly

installed in accordance xdth the Installation

Instructions befk)re it is used.

Never unplug your air conditioner by pulling

on the power cord. Always _-ip plug firmly

and pull straight out flom the receptacle.

Replace immediately 'allelectric ser\@e

cords that have become flayed or otherwise

damaged. A damaged power supply cord

must be replaced with a new power supply

cord obtained from the manufacturer and

not repaired. Do not use a cord that shows

cracks or abrasion damage along its len_h

or at either the plug or connector end.

Turn the unit OFFandunplug your air

conditioner before cleaning.

iii}i}i

iii}i}}li_

GE does not support any ser\,icing of the air

conditioner We strongly recommend that

you do not attempt to ser\,ice the air

conditioner yoursel£

For your sNety...do not store or use

combustible materials, gasoline or other

flammable vapors or liquids in the x,icinity

of this or any other appliance.

All air conditioners contain refligerants,

which under federal law must be removed

prior to product disposal. If you are getting

rid of an old product with refrigerants,

check with the company handling disposal

about what to do.

If the receptacle does not match the plug,

the receptacle must be changed out by a

qualified electrician.

HOWTOCONNECTELECTRICITY

Do not, under any circumstances, cut or remove

the third (ground) prong from the power cord.

For personal safety, this appliance must be

properly grounded.

DONOT use anadapterplug with this appliance.

The power cord of this appliance is equipped

with a 3-prong (grounding) plug which mates

with a standard 3-prong (grounding) wall

outlet to minimize the possibility of electric

shock hazard flom this appliance.

Power cord includes a current intermpmr

dex,ice. A test and reset button is prox,ided on

the plug case. The dex,ice should be tested on a

periodic basis by first pressing the rESrbutton

and then the RESErbutton while plugged into

the outlet. If the rESrbutton does not trip

or if the RESErbutmn will not stay engaged,

discontinue use of the air conditioner and

contact a qualified ser\,ice technician.

Have the wall outlet and circuit checked by

a qualified electrician to make sure the outlet

is properly _ounded.

Where a 2-prong wall outlet is encounmred,

it is your personal responsibility and obligation

to have it replaced with a properly grounded

3-prong wall outlet.

The air conditioner should always be plugged

into its own indix,idual electrical outlet which

has a voltage rating that matches the rating

plate.

This prox,ides the best perfk_rmance and also

prevents overloading house xdring circuits

which could cause a fire hazard flom

overheated xdres.

See the Installation Instructions, Electrical

Requirements section f_r specific electrical

connection requirements.

2

WARNING!

USEOFEXTENSIONCORDS--115-Voltmodelsonly

Because of potential safety hazards under certain

conditions, we strongly recommend against the

use of an extension cord.

However, if you must use an extension cord,

it is absolumly necessa U that it be a UL-listed,

14-gauge, 3:wire grounding-type appliance

extension cord ha\,ing a _oundinDtype plug

and outlet and that the electrical rating of the

cord be 15 amperes (minimum) and 125 vohs.

-4,CAUTION:

DO NOT usean extension cord with any ofthe

230/208 voltmodels.

ge.com

READANDFOLLOWTHISSAFETYINFORMATIONCAREFULLY.

SAVETHESEINSTRUCTIONS

3

Aboutthe controlsontheair conditionermmodelswith touchpads.

Features and appearance will van

Lights next to the touch pads on the air conditioner control panel indicate the selected settings.

Thedisplayalwaysshowsthe room

temperatureexceptwhensettingthe

Settemperatureor theDelaytimer.

Light indicatesthe unit

is in the temperatureor

delaytime Set mode.

m Auto

m High m Fan Only

amNed _,_Energy Saver

w, Low m Cool

_ _SFe_d_d_EMode _J Fan

Light indicates the

delay timer is set.

Delay

O Delaytimer --

Decrease I

O o'e eeo'--T-

O anspeed

Decrease

Temperature --

set hlcrease

and Decrease

Delaytimer Increase

Auto Fanon/off

FanspeedIncrease

Unit poweron/off

Air Conditioner Controls

Remote Control

Contro/s

O ower Pad

Turns air conditioner on mM off. When

ulrned on, the display will show the room

temperature.

0 Display

Shows tile room temperature or time

remaining on the Del W fimeL Shows the Set

mmperature while setting the mmperature in

Coolor Energy Saver modes. The Set light will

mrn on while setting.

NOTE:The display will change to show file

room temperature after settings have been

made. To recall the Set mmpemmre, press the

TempIncrease • or Decrease • pads.

O empIncrease •/Decrease • Pads

Use to set temperature when in Cool or Energy

Savermode. The Setlight will mrn on while

setting.

O Delay fimerlncrease • (+)/Decrease • (-)

Pads

Each touch of the Increase •/Decrease •

pads on the unit or the Increase+/Decrease -

pads on the remote control will set the delay

time when using tlle Delay1-24hrtimer ((_).

The Setlight will mrn on while setting.

O an Speed Pads

Use to set the fan speed to LOW,Med, High

or Auto on the unit. NOTE:On the remote

conuol, use the fan speed Increase +/

Decrease - pads to set the fan speeds to LOW,

Med or High. Use tt_e Auto pad m mrn Auto

filIl Oil.

O ode Pad

Use to set tl_eair conditioner to Cool,Energy

Saveror FanOnlymode.

0

Delay Pads

Delay ON--When the air conditioner is of L it

can be set to automatically come on in 1 to 24

hems at its previous mode and fan settings.

Delay OFF--When the air conditioner is on,

it can be set m automatically mrn off in 1 m

24 hems.

How toset:

Press file Delay 1-24hr pad on the trait or

die _ pad on file remora conUol. Each touch

of the Increase •/Decrease • pads on the

unit or the Increase +/Decrease- pads on

tile remote control will set the timer in

1-hour intervals. The Set light will mrn on

while setting.

To review die remaining time on die Delay

1-24hrtime_; press the Delay 1-24hr pad on the

unit or the @ pad on the remote control. Use

the Increase •/Decrease • pads on the unit

or the Increase +/Decrease-pads on the

remote control to set a new time if desired.

Tocancel the timer, press tt_e Delay 1-24hr pad

until tile light on the Delay 1-24hr pad goes off:

4

ge.com

Do Not Operate in Freezing Outdoor Conditions

This cool<rely air conditioner was not designed for

fleezing outdoor conditions. It illust not be used in

fleezing outdoor conditions.

Remote Control

To ensure proper operation, aim file remora

conuol at the signal receiver on the air

condifioneL

Tile remote conuol signal has a range of

up m 20 feet.

Make sure riDdling is between die air conditioner

and the remora conuol that could block the

sigmal.

Make sure batteries are flesh and instaUed

correctly _tsindicated on the remora conuol.

CoolMode

Use file Coolmode at Low,Med,Highor AutoFan

Speedfor cooling. Use tile TemperatureIncrease• /

Decrease • pads to set tile desired temperature

between 64°F and 86°F in 1°F increments.

An electronic fllemlostat is used to maintain file

room temperature. Tile compressor will cycle on

and off to keep file room at file set level of comfort.

Set file themlostat at a lower number and file indoor

air will become cooleL Set die fllelInostat at a higher

number and file indoor air will become wamleL

NOTE:If theairconditionerisoffandisthenturnedon

whileset toa Coolsettingorif turnedfromafansetting

toa Coolsetting,it maytakeapproximately3minutes

forthecompressortostartandcoolingtobegin.

CoolingDescriptions

ForNormalCooling--Selectthe Coolmode and

Highor Med fan with a middle set temperature.

ForMaximum Cooling--Select tile Coolmode

and Highfan with a lower set temperature.

ForQuieterandNighttimeCooling--Selecttile

Cool mode and Low fan with a middle set

temperature.

Energy Saver Mode

Controls tile fan.

ON--The fan will cycle on and offwidl die

compressor. This results in wider variations of room

temperature and humidity. Normally used when tile

room is unoccupied. NOTE: The fan may continue to run

forashort time after the compressorcycles off.

OFF--The tim runs all tile time, while file

compressor cycles on and off:

Fan OnlyMode

Use the FanOnlyModeat Low,Medor Highfan

speed to provide air circulation and filtering

without cooling. Since fan-only settings do not

provide cooling, a Set mmperamre camlot be

enmred. Tile room mmpemmre will appear

in tile displ W.

NOTE:AutoFanSpeedcannotbeusedwheninthe

FanOnlyMode.

Auto Fan Speed

Set to Autofan speed for tile fan speed to

automatically set m tile speed needed m provide

optimum comfort settings wifll tile set temperature.

If the room needs more cooling, the fan speed

will automatically incre_tse. If the room needs less

cooling, the fan speed will automatically decrease.

NOTE:AutoFanSpeedcannotbeusedwheninthe

FanOnlyMode.

Power Outage Recovery Feature

In tile case of a power outage or interruption, tile

unit will automatically restart in the settings last

used after tile power is restored. If tile Delay 1-24hr

feature was set, it will resume countdown. You may

need to set a new time if desired. 5

Aboutthecontrolsontheair conditionermmodelswith controlknobs.

Features and appearance will van

MODE

High •

Cool.

Cool

OFF

High

MODECONTROL

TEMP

Coolest

TEMPERATURECONTROL

Controls (onsomemodels)

0

Mode Control

HighCool,Med Cooland LowCool

provide cooling with (liff_rent fan speeds.

Fan settings provide Mr circulation and

filtering Mfllout cooling.

NOTE:If youmovethemodecontrolfroma cool

settingtoOFFortoa fansetting,waitatleast

3 minutesbeforeswitchingbacktoa coolsetting.

Cooling Descriptions

ForNormal Cooling--Select HighCoolor Med Cool

with tile TEMPERATURE control at midpoint.

ForMaximum Cooling--Select High Coolwith tile

TEMPERATURE control at the highest number

available on your knob.

ForQuieterandNighttimeCooling--Select Low

Coolwith tile TEMPERATURE control at

midpoint.

O

TEMP Control

Tile TEMP control is used to maintain the

room tempe_mre. Tile compressor will cycle

on and off"m keep tile room at tile same level

of comfoit. _r]len you mrn the knob to a

higher numbe_; the indoor air will become

cooleL Turn the knob m a lower number mid

tile indoor air will become warmeL

Contlo/s (onsomemodels)

OFF

ON

()

ON/OFFControl

Turns air conditioner on and off.

NOTE:If theairconditionerisoffandisthenturnedonwhile

setinaCoolmode,it will takeapproximately3minutesfor

thecompressortostartandcoolingtobegin.

6

Additional important information.

Air Direction

Use die lever to adjust file air direction left and

right only.

ge.com

Appearancemayvary.

Careand cleaning oftheair conditioner.

Grille and Case

Turn tile air conditioner off and remove tile plug

from tile wall oudet before cleaning.

To clean, use water and a mild detergent. Do not

use t)leach or abrasives.

Air Filter

The air filter behind the front grille should be

checked and cleaned at least eve_T 30 days or

more often if necessary.

Toremove:

Push on one side of the filter edge and pull it out

the other side.

Clean tlle filter widl warm, soap), wateL Rinse and

let the filter dry before replacing it. Do not clean

the filter in a dishwasheL

CAUTION:DoNoroperatetheair

conditioner without a filter becausedirt andlint will clog

it and reduceperformance.

Appearancemayvary.

Outdoor Coils

The coils on the outdoor side of the air conditioner

should be checked regularly: If they are clogged

with dirt or soot, they may be professionally cleaned.

How to Insert the Batteries in the Remote Control

[-_ Remove the batte D,cover by sliding it

according to the arrow direction.

Insert new batteiJes, making sure that the (+)

and (-) of battery are installed correcOy.

[-_ Reatmch the cover by sliding it back

into position.

NOTES:

Use 2 "AAA" (1.5 volt) alkaline batteries. Do not

use rechargeable batm_ies.

Remove the batteIies flom the remora control if

the sysmm is not going m be used for a long time.

7

Installation

Instructions

Air Conditioner

=_ uestions? Call 800.GE.CARES (800.432.2737) or visit our Website at: ge.com

In Canada, call 1.800.561.3344 or visit www.GEAppliances.ca

I

BEFORE YOU BEGIN

Read these instructions completely

and carefully.

IMPORTANT - Savethese

instructions for local inspector's use.

• IMPORTANT - Observeall

governing codes and ordinances.

• Note to Installer- Be sure to leave these

instructions with the Consumer.

• Note to Consumer- Keep these

instructions for future reference.

• Skill level - Installation of this appliance

requires basic mechanical skills.

• Completion time- Approximately 1 hour

• We recommend that two people install

this product.

• Proper installation is the responsibility

of the installer.

Product failure due to improper installation

is not covered under the Warranty.

You MUST use all supplied parts and use

proper installation procedures as described

in these instructions when installing this air

conditioner.

(_ ELECTRICAL REQUIREMENTS

Some models require a 115/120-volt AC,

60-Hz grounded outlet protected with a

15-amp time-delay fuse or circuit breaker.

The 3-prong grounding plug minimizes the

possibility of electric shock hazard. If the wall

outlet you plan to use is only a 2-prong outlet,

it is your responsibility to have it replaced with

a properly grounded 3-prong wall outlet.

©

Some models require 230/208-volt AC,

protected with a time-delay fuse or circuit

breaker. These models should be installed

on their own single branch circuit for

best performance and to prevent

overloading house or apartment wiring

circuits, which could cause a possible

fire hazard from overheating wires.

- CAUTION:

Do not, under any circumstances, cut or

remove the third (ground) prong from the

power cord.

Do not change the plug on the power cord

of this air conditioner.

Aluminum house wiring may present special

problemsmconsult a qualified electrician.

TOOLS YOU WILL NEED

Phillips-head screwdriver

Flat-blade screwdriver

Pencil Ruler or tape measure

Level Scissors or knife

8

Power cord includes a current interrupter

device. A test and reset button is provided on

the plug case. The device should be tested on a

periodic basis by first pressing the TEST button

and then the RESET button while plugged into

the outlet. If the TEST button does not trip or

if the RESET button will not stay engaged,

discontinue use of the air conditioner and

contact a qualified service technician.

Installation Instructions

PARTS INCLUDED

(Appearance may vary)

Top mou_

Air

conditioner

\

Window

eal

vv,_a_;_

Left

accordion

panel

Right

accordion

panel

- /

Top mo "_

seal strip

Type A (6) Type B (3) Type C (5)

Window locking

bracket (1)

9

Installation instructions

ITi WINDOW REQUIREMENTS

• These instructions are for a standard double-

hung window. You will need to modify them

for other types of windows.

• The air conditioner can be installed without

the accordion panels if needed to fit in a

narrow window. See the window opening

dimensions.

All supporting parts must be secured

to firm wood, masonry or metal.

The electrical outlet must be within reach of

the power cord.

Follow the dimensions in the table and

illustration for your model.

Models A B

AEH05, AES05 13" min. 24 1/2"-38 1/8"

AEH06, AEH08 13 5/8" min. 24 1/2"-38 1/8"

B====_

t

A

(With accordion panels)

121STORM WINDOW REQUIREMENTS

A storm window frame will not allow the air

conditioner to tilt toward the outside, and will

keep it from draining properly.

To adjust for this, attach a piece of wood to

the sill.

WOOD PIECES

WIDTH: 2"

LENGTH: Long enough to fit inside the

window frame.

THICKNESS: To determine the thickness, place

a piece of wood on the sill to make it 1/2"

higher than the top of the storm window

frame or the vinyl frame.

Attach securely with nails or screws provided

by the installer.

1/2" higher

than vinyl frame

L (on some windows)

/

w

1/2" higher _ _ ________._ Wood

than storm _

window " "_

frame

Storm window

frame

10

[] ATTACH THE TOP MOUNTING

RAIL SEAL STRIP

Remove the backing from the top mounting

rail seal strip and attach the seal strip to the

bottom of the top mounting rail, along the

front edge.

Top mounting rail

Remove

backing

from seal

strip

FRONT ViEW

Topmounting rail

/

Seal strip

141PREPARE THE AIR CONDITIONER

[] Install the top mounting rail with 3 Type B

screws from the outside of the case,

Top mounting rail

Bottom mounting rail

r_ Slide the left and right accordion panels

into the top and bottom mounting rails.

Top right

Top left

Installation Instructions

141PREPARE THE AIR CONDITIONER

(cont.)

[] Attach the accordion panels to the case

using 3 Type A screws on each side.

Top mounting rail

Accordion

panel

Type

screws

BACK

Bottom mounting rail

151PREPARE THE WINDOW

Cut the window sash seal to the proper

length. Peel off the backing and attach the

seal to the underside of the window sash.

161INSTALL THE AIR CONDITIONER

IN THE WINDOW

[_] Place the air conditioner on the sill with

the bottom mounting rail against its back

edge. Center it and close the window

securely behind the top mounting rail.

It should be level or slightly tilted to the

outside. Use a level; about a 1/3 bubble

will be the correct case slant to the outside.

Type C screws

[] Extend the left and right accordion panels

to the vertical window sashes and attach,

through the holes in the panels, with 4

Type C screws, as appropriate.

11

m INSTALL SUPPORT BRACKET AND

FOAM TOP WINDOW GASKET

[] CAUTION:

To prevent broken glass

or damage to windows,

on vinyl or other

similarly constructed

windows, attach the

support bracket to the

window side jam.

Vinyl

Attach the support

bracket with one

Type C screw.

Wood

[]

Cut the foam top window gasket to the

window width.

Stuff the foam

between the

glass and the

window to

prevent air and

insects from

getting into the room.

NOTE: If the gasket supplied does not fit

your window, obtain appropriate material

locally to provide a proper installation seal.

TroubleshootingTips.

Airconditioner

doesnotstart

Possible Causes What ToDo

The air conditioner

is tmplugged.

The fuse is blown/circuit

breaker is tripped.

Power failure.

• Make sure the air conditioner plug is pushed

completely into tile outlet.

• Check tile house fixse/circuit breaker box and replace

tile flxseor reset tile breakeL

• Tile unit will automatically restart in tile settings last

used after the power is restored.

• There is a protective time del W (approximately

3 minutes) to prevent tripping of tile compressor

overload. Fox this reason, tile unit may not start

normal cooling for 3 minutes after it is turned

back on.

The current interrupter • Press the RESETbutton located on the power cord plug.

device is tripped. • If tile RESETbutton will not stay engaged, discontinue

use of tile air conditioner and contact a qualified

service technician.

Air conditioner does Airflow is restricted. • Make sure there are no curtains, blinds or fiuniture

not cool as it should blocking the flont of the air condifioneL

The temp control may • On models wifll touch pads: In tile Cool mode, press tile

not be set correctly. Decrease • pad.

• On models with control kalobs, mrn tile temperature

knob m a higher numbeL

The air filter is dirty. • Glean tile filter at least every 30 days.

See tile Care and Cleaning section.

The room may have been hot. • When tile air conditioner is filst turned on, you need

to allow time for file room to cool down.

Cold air is escaping. • Gheck for open fiunace regfiste_ and cold air returns.

Cooling coils have iced up. • See "Air conditioner freezing up" below.

Air conditioner

freezingup

Ice blocks the air flow

and stops the air conditioner

from cooling the room.

• On models widl conUol knobs, set die mode conuol at

HighFanor HighCoolwitb the rempat I or 2.

• On models with touch pads, set tile controls at HighFan

or High Cooland set the tbemlosmt m a higher

tempex_mxre.

Theremote control The batteries are inserted *Check tile position of tile batteries. Tile), should be

is not working incorrectly, inserted in tile opposite (+) and (-) direction.

The batteries may be dead. =Replace the batteries.

Waterdrips outside Hot, humid weather. • This is normal.

Waterdrips indoors The air conditioner is not • Fox proper water disposal, make sure tile air conditioner

tilted to the outside, slants slightly from the case flont to the real

Watercollects in Moisture removed from air • This is normal for a short period in areas with little

basepan and drains into base pan. humidiD,; hernial for a longer period in very humid areas.

72

Normal Operating Sounds

You may hear a pinging noise caused by water

being picked up and thrown against tile

condenser on rainy dws or when the humidity

is high. This design feature helps remove

moisture and improve efficiency.

}_You may hear tile thernlosmt click when tile

compressor cycles on and off:

Water Mll collect in die base pan during

high humidity or on rainy days. Tile wamr

may overflow and drip flom tile outdoor side

of tile unit.

}_Tile fan may run even when tile compressor

does not.

Page is loading ...

For Canadian

Customers

Pour les

Consommateurs

Canadiens

z

c_

z

<

LIJ

Z

--J

I

F-

(.9

Z

Pleaseregisteryour product to enableusto contactyou

inthe remoteeventasafetynotice isissuedforthis product

andto allowfor efficientcommunication undertheterms

ofyourwarranty,shouldthe need arise.

REGISTERON-UNE: www, geappliances,ca

ENREGISTREMENTSURINTERNET_,: www.eleetremenage[sge.ca

[] MR./M [] MRS./MNE.FIRSTNAME/PRCNOM[] MISS/MLLE,[] MS.

STREETNO/N°RUE STREETNAME/RUE

CITY/VlLLE

AREACODE/IND.REG.JTELEPHONE _E-MAIL

DIDYOUPURCHASEASERVICECONTRACTFORTHISAPPLIANCE?

AVEZ-VOUSACHETt_UN CONTRATDESERVICEPOURCETAPPAREIL?

Veuillezenmgistrervotreproduitafindenouspermettrede

communiqueravecvoussijamaisunavisdes6curi_concemant

ceproduit_it 6misetdecommuniquerfacilementavecvousen

vertudevo_egararde,silebesoins'enfaitsen_r.

P.O.BOX1780,MISSISSAUGA

ONTARIO,L4Y461

MAJLTO:

POSTERA:

LASTNAME/NOM

APT.NO/APR/RR#

PROVINCE POSTALCODE/POSTAL

YES/OUI [] IFYES/SIOUhEXPIRATDN

Y/A M D/J

NO/NON D

NAME OFSELUNGDEALER/ NOMDUMARCHAND

INSTALL&]]ONDATE/DATED'INS_ALLATION

Y/A M D/J CORRESPONDENCE [] ENGUSH

CORRESPONDANCE [] FRAN_AIS

MODEL/MOD_:LE

SERIAL/SERIE

[] Ido notwishtoreceiveanypromotionaloffersregardingthisproduct

[] Jenedesirepasrecevoird'offrespromotionnellesconcemantceproduit.

14

GEAir Conditioner--One- YearLimitedWarranty.(For customers in the U.S.A.)

Staple your receipt here.

Proof of the original purchase date

is needed to make a warranty claim.

One Year

Fromthedateorthe

original purchase i

We Will Replace:

Replacement unitfor any product which fails due m a defect in materials or worl_nanship.

Tile replacement unit is waII_tnted fox tile remainder of your product's original oneg_ear

wanmlty period.

Properly pack your unit. We recommend using the

original carton and packing materials.

Return the product to the retail location where it

was purchased.

Include in the package a copy of the sales receipt or other

evidence of date of original purchase. Also print your

name and address and a description of the defect.

iil iii il !!!!!!!Ill

}_Customer instruction. This owner's manual provides

information regarding operating instructions and

user controls.

}_Improper installation, delivery or maintenance. If you

have an installation problem, or if the air conditioner is

of improper cooling capacity, contact your dealer or

installer. You are responsible for providing adequate

electrical, plumbing and other connecting facilities.

Failure of the product resulting from modifications to

the product or due to unreasonable use, including failure

to provide reasonable and necessary maintenance.

Replacement of house fuses or resetting of circuit

breakers.

Failure due to corrosion on models not corrosion-

protected.

Damage to the product caused by improper power supply

voltage, accident, fire, floods or acts of God.

Incidental or consequential damage caused by possible

defects with this air conditioner.

Damage caused after delivery.

EXCLUSIONOFIMPLIED WARRANTIES--Your sole and exclusive remedy is product replacement as provided

in this Limited Warranty. Any implied warranties, including the implied warranties ofmerchantability or

fitness for a particular purpose, are limited to one year or the shortest period allowed bylaw.

This warranty is extended to the original purchaser and any succeeding owner for products purchased for home

use within the USA.

Some states do not aflow the exclusion or limitation of incidental or consequential damages. This warranty gives

you specific legal rights, and you may also have other rights which vary from state to state. Toknow what your

legal rights are, consult your local or state consumer affairs office or your state's Attorney General

Exclusion of implied warranties: Except where prohibited or restricted by law, there are no warranties, whether

express, oral or statutory which extend beyond the description on the face hereof, including specifically the

impfied warranties of merchantability or fitness for a particular purpose.

Warrantor: General Electric Company. Louisville, KY 40225

15

GEAir Conditioner--One- YearLimitedWarranty.(ForcustomersinCanada)

Staple your receipt here.

Proof of the original purchase date

is needed to make a warranty claim.

OneYear

Fromthe dateofthe

Originalpurchase I

We Will Replace:

Replacement unitfor any product which fails due m a defect in materials or workmanship.

The replacement unit is warI_nted for file remainder of your product's originM one-year

waII_in t), period.

Properly pack your unit. We recommend using the

original carton and packing materials.

Return the product to the retail location where it

was purchased.

Include in the package a copy of the sales receipt or other

evidence of date of original purchase. Also print your

name and address and a description of the defect.

Customer instruction. This owner's manual provides

information regarding operating instructions and

user controls.

Improper installation, delivery or maintenance. If you

have an installation problem, or if the air conditioner is

of improper cooling capacity, contact your dealer or

installer. You are responsible for providing adequate

electrical, plumbing and other connecting facilities.

Failure of the product resulting from modifications to

the product or due to unreasonable use, including failure

to provide reasonable and necessary maintenance.

Replacement of house fuses or resetting of circuit

breakers.

Failure due to corrosion on models not corrosion-

protected.

Damage to the product caused by improper power supply

voltage, accident, fire, floods or acts of God.

Incidental or consequential damage caused by possible

defects with this air conditioner.

Damage caused after delivery.

EXCLUSIONOFIMPLIED WARRANTIES--Your sole and exclusive remedy is product replacement as provided

in this Limited Warranty. Any implied warranties, including the implied warranties of merchantability or

fitness for a particular purpose, are limited to one year or the shortest period allowed by law.

This warranty is extended to the original purchaser and any succeeding owner for products purchased in Canada

for home use within Canada.

Some provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion

may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from

province to province. Toknow what your legal rights are in your province, consult your local or provincial consumer

affairs office.

Exclusion of impfied warranties: Except where prohibited or restricted by law, there are no warranties, whether

express, oral or statutory which extend beyond the description on the face hereof, including specifically the

impfied warranties of merchantability or fitness for a particular purpose.

Warrantor'. Mabe Canada Inc.,

Burlington, Ontario

76

Page is loading ...

For Canadian

Customers

Pour les

Consommateurs

Canadiens

zl

!E

Z I

C31

kkll

ZI

Pleaseregisteryourproducttoenableustocontactyou VeuiUezenregistrervotreproduitafindenouspermed_ede

in the remote event a safety nonce is issued for this product communiquer avec vous sijamais un avis de s6curi_ concemant

and to aUow for efficient communication under the terms ce produit et,ait 6mis et de communiquer facibment avec vous en

of your warrant_; should the need arise, vertu de vol_ garan_e, si le besoin s'en fair sentir.

REGISTERON-UNE: www.geappliances.ca MAILTO:, P.O.BOX1788,MISSISSAUGA

ENREGISTREMENTSURINTERNETA:www.electrornena,qersge.ca POSTERA: ONTARIO,L4Y4GI

[][] MISS/MLLE.MR'/M[][] Ms.MRS'/MNE"FIRSTNAME/PRt_NOM LASTNAME/NOM

STREETNO/N° RUE STREETNAME/RUE

CITY/VILLE

'AR COOE,,NOREOL'LEP.ONE[EOOL

DiDYOUPURCHASEASERVICECONTRACTFORTHISAPPLIANCE?

AVEZ-VOUSACHETEUN CONTRATDESERVICEPOURCETAPPAREIL?

APT.NO/APP./RR#

PROVINCE POSTALCODE/POSTAL

IFYES/SIOUhEXPIRATION

Y/A M D/J

YES/OUI[]

NO/NOND

NAMEOFSELLINGDEALER/ NOMDU MARCHAND MODEL / MODELE

INSTALLATIONDATE/ DATED'INSTALLA_ION/

Y/A M D/J CORRESPONDENCE [] ENGLISH

J

CORRESPONDANCE [] FRANOAIS SERIAL/SI_RI E

D Ido notwishtoreceiveanypromotionaloffers_egardingthisproduct.

El Jened6sirepasrecevoird'offrespromotionnelbsconcemantceproduit.

3O

Page is loading ...

ConsumerSupport.

GEAppliancesWebsite In the U.S.A.ge.com

Have a question or need assistance with your appliance? TD_the GE Appliances Website 24 hours a day,

any day of the year! Fox greater convenience and fi,tster service, you can now download Owner's Manuals,

or even order parts on-line. In Canada: www.GEApplianees.ea

RealLifeDesignStudio In the U.S.A.ge.com

GE supports the Universal Design concept--pxoducts, sexMces and envirolmlents that can be used by

people of aU ages, sizes and capabilities. We recogmize the need m design for a wide range of physical

and mental abilities and impaimmnts. Fox details of GE's Univexsal Design applications, including kitchen

design ideas fox people with disabilities, check out our Website today. Fox the hearing impaired, please call

800.TDD.GEAC (800.833.4322).

In Canada, contact: Managex, Consumer Relations, Mabe Canada Inc.

Suite 310, i Factory Lane

Moncton, N.B. EIC 9M3

PartsandAccessories

In the U.S.A.ge.com

IndMduals qualified to service their own appliances can have parts or accessories sent direcdy to their

homes (VISA, MasterCard and Discover cards are accepted). Order on-line today, 24 horns every day or

by phone at 800.626.2002 during normal business hours.

Instructionscontainedinthismanualcoverprocedurestobeperformedbyanyuser.GEdoesnotsupportany

servicingoftheair conditioner.Westronglyrecommendthatyoudonotattempttoservicetheair conditioner

yourself.

Customers in Canada should consult the yellow pages for the nearest Mabe sexMce centex;

or call 1.800.561.3344.

ContactUs

/n the U.S.A.ge.com

If you are not satisfied Mill die sexMce you receive flom GE, contact us on our Website Mill all die details

including your phone numbex, or write to: GenerM Managex, Customer Relations

GE Appliances, Appliance Park

Louisville, KY40225

In Canada: www.GEAppliances.ca, or write to: Directox, Consumer Relations, Mabe Canada Inc.

Suite 310, i Factory Lane

Moncton, N.B. Ell(; 9M3

Printed in China

GE AEH05LMS1 Owner's manual

GE AEH05LMS1 Owner's manual

in other languages

Related papers

Other documents