George Kovacs P1382-077-L User manual

Brand
George Kovacs
Model
P1382-077-L
Type
User manual
IMPORTANT: Fixture should be installed by a qualified
electrician to ensure proper wiring and installation.
Dimmable with ELV dimmer switches.
INSTALLATION INSTRUCTIONS FOR P1382-077-L/P1383-077-L/P1384-077-L
For Wall Mount Fixture
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
AVE RT I SS E ME N T ! CO U P E R L E C O U RA NT A U N I V E AU D E S FU S I B L E S O U D O D I SJ O N C TE U R.
AV E R T I S S E M E N T ! C O U P E R L E C O U R A N T A U N I V E A U D E S F US I B L E S OU D O D IS J O N C T EU R .
PREPARATION
1. Shut off power at the fuse box or circuit breaker box. If
necessary remove the old fixture and mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts
on a clear area. Take care not to lose any small parts
necessary for installation.
MOUNTING THE FIXTURE (FIG. 1)
3. Align the glass (K) to the metal arm (I), tighten with washer
(J), gasket (O) and screw (L). Fix the metal arm (I) to the
bracket (N) by screw (M). Use the “key holes” located on
the mounting plate (B) as a template to mark the location of
the plastic anchors (D) and pre-drill two holes
4. Install the plastic anchors (D) into the wall.
5. Secure mounting plate (B) to junction box (A) using
junction boxes screws (C) (Size: 8-32*1/2”L). The side of
the mounting back plate marked “GND” must face out.
6. Align the “key holes” on the mounting plate (B) to the
plastic anchors (D) and secure with screws (E).
CONNECTING THE WIRES (FIG. 2)
7. At this point, connect the electrical wires as shown in Fig. 2,
making sure that all wire connectors are secured. If your
outlet has a ground wire (green or bare copper), connect
the fixtures ground wire to it. Otherwise, connect the fixture
ground wire directly to the mounting plate (B) using the
green screw (G) provided. After wires are connected, tuck
them carefully inside the junction box.
COMPLETING THE INSTALLATION (Fig. 1)
8. Install the bracket (Z) into mounting plate (B) using screw
(H).
Your installation is now completed. Return power to the junction box
and test the fixture.
CAUTION /ATTENTION: When handling the fixture, do not
apply pressure to the LEDs. Hold the fixture by the base or
bracket.
Replacing LED module (Fig. 3)
The LED module can be replaced by a qualified electrician
without cutting of wire and without damage to any decorative
element to which the fixture is attached. See installation steps
for more details (Fig 3.)
a. Shut off power. Remove the fixture from the wall.
b. Remove the screw (P) to disconnect the heat sink (W) from
the bracket.
c. Remove screw (U) and use a pin to press the hole on the
quick connector (X) to disconnect LED module.
d. Reverse steps a-c for installing the new LED module.
Note: The LED module should be provided by a specified
supplier.
FIG.1
Set #
P1382-077-L : A-021-341113
P1383-077-L : A-021-564113A
P1384-077-L : A-021-803113
- Mounting plate - Ground screw
- Mounting screw*2pcs
Fig.3
Fig.2
HOUSE
WIRES
Black
(Hot)
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
Green or
Bare
Copper(G
round)
  • Page 1 1

George Kovacs P1382-077-L User manual

Brand
George Kovacs
Model
P1382-077-L
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents